JVC-MXGA3V-cs-sm 维修电路原理图.pdf

《JVC-MXGA3V-cs-sm 维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《JVC-MXGA3V-cs-sm 维修电路原理图.pdf（65页珍藏版）》请在收音机爱好者资料库上搜索。

1、MX-GA3VContentsSafety precautions - 1- 2Important for laser products - 1- 3Preventing static electricity - 1- 4Disassembly method - 1- 5Adjustment method - 1- 18Flow of functional operation until TOC read - 1- 20Maintenance of laser pickup - 1- 21Replacement of laser pickup - 1- 21Description of maj

2、or ICs - 1- 22SP-MXGA3VCA-MXGA3VSP-MXGA3VArea SuffixUS . SINGAPOREUX . Saudi AraiaCOPYRIGHT 2003 VICTOR COMPANY OF JAPAN, LTD. No. MB0362003/11MX-GA3VSERVICE MANUAL COMPACT COMPONENT SYSTEMWiring connection - 1- 29RadioFans.CN 收音机爱 好者资料库MX-GA3V1-2Warning ! CAUTIONGood earth groundPlace this probe on

3、 each exposedmetal part.AC VOLTMETER(Having 1000 ohms/v1500 10Wolts,or more sensitivity)0.15 F AC TYPESafety Precautions1. This design of this product contains special hardware and many circuits and components specially for safety purposes. For continued protection, no changes should be made to the

4、original design unless authorized in writing by the manufacturer. Replacement parts must be identical to those used in the original circuits. Services should be performed by qualified personnel only.2. Alterations of the design or circuitry of the product should not be made. Any design alterations o

5、f the product should not be made. Any design alterations or additions will void the manufacturers warranty and will further relieve the manufacture of responsibility for personal injury or property damage resulting therefrom.3. Many electrical and mechanical parts in the products have special safety

6、-related characteristics. These characteristics are often not evident from visual inspection nor can the protection afforded by them necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special safety characteristics are i

7、dentified in the Parts List of Service Manual. Electrical components having such features are identified by shading on the schematics and by ( ! ) on the Parts List in the Service Manual. The use of a substitute replacement which does not have the same safety characteristics as the recommended repla

8、cement parts shown in the Parts List of Service Manual may create shock, fire, or other hazards. 4. The leads in the products are routed and dressed with ties, clamps, tubings, barriers and the like to be separated from live parts, high temperature parts, moving parts and/or sharp edges for the prev

9、ention of electric shock and fire hazard. When service is required, the original lead routing and dress should be observed, and it should be confirmed that they have been returned to normal, after re-assembling. 5. Leakage currnet check (Electrical shock hazard testing) After re-assembling the produ

10、ct, always perform an isolation check on the exposed metal parts of the product (antenna terminals, knobs, metal cabinet, screw heads, headphone jack, control shafts, etc.) to be sure the product is safe to operate without danger of electrical shock. Do not use a line isolation transformer during th

11、is check.? Plug the AC line cord directly into the AC outlet. Using a Leakage Current Tester, measure the leakage current from each exposed metal parts of the cabinet, particularly any exposed metal part having a return path to the chassis, to a known good earth ground. Any leakage current must not

12、exceed 0.5mA AC (r.m.s.)? Alternate check method Plug the AC line cord directly into the AC outlet. Use an AC voltmeter having, 1,000 ohms per volt or more sensitivity in the following manner. Connect a 1,500 10W resistor paralleled by a 0.15 F AC-type capacitor between an exposed metal part and a k

13、nown good earth ground. Measure the AC voltage across the resistor with the AC voltmeter.Move the resistor connection to each exposed metal part, particularly any exposed metal part having a return path to the chassis, and meausre the AC voltage across the resistor. Now, reverse the plug in the AC o

14、utlet and repeat each measurement. Voltage measured Any must not exceed 0.75 V AC(r.m.s.). This corresponds to 0.5 mA AC(r.m.s.). 1. This equipment has been designed and manufactured to meet international safety standards.2. It is the legal responsibility of the repairer to ensure that these safety

15、standards are maintained.3. Repairs must be made in accordance with the relevant safety standards.4. It is essential that safety critical components are replaced by approved parts.5. If mains voltage selector is provided, check setting for local voltage.Burrs formed during molding may be left over o

16、n some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system.RadioFans.CN 收音机爱 好者资料库MX-GA3V1-3VIDEO OUT110V127V220V230V-240VWARNING LABEL1. CLASS 1 LASER PRODUCT2. CAUTION : Visible and invisible laser radiation when open and interlock failed or

17、 defeated. Avoid direct exposure to beam.3. CAUTION : There are no serviceable parts inside the Laser Unit. Do not disassemble the Laser Unit. Replace the complete Laser Unit if it malfunctions.4. CAUTION : The compact disc player uses invisible laser radiation and is equipped with safety switches w

18、hich prevent emission of radiation when the drawer is open and the safety interlocks have failed or are defeated. It is dangerous to defeat the safety switches. Important for laser productsREPRODUCTION AND POSITION OF LABELS5. CAUTION : If safety switches malfunction, the laser is able to function.6

19、. CAUTION : Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. ! CAUTION Please use enough caution not to see the beam directly or touch it in c a s e o f a n a d j u s t m e n t o r operation check. VARNING : Osynl

20、ig laserstrlning r denna del r ppnad och sprren r urkopplad. Betrakta ej strlen.VARO : Avattaessa ja suojalukitus ohitettaessa olet alttiina nkymttmlle lasersteilylle. l katso steeseen. ADVARSEL : Usynlig laserstrling ved bning, nr sikkerhedsafbrydere er ude af funktion. Undg udsttelse for strling.A

21、DVARSEL : Usynlig laserstrling ved pning, nr sikkerhetsbryteren er avslott. Unng utsettelse for strling.MX-GA3V1-4Preventing static electricity1. Grounding to prevent damage by static electricityElectrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is d

22、ischarged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.2. About the earth processing for the destruction prevention by static electricityIn the equipment which uses optical pick-up (laser diode), optical pick-up is destroyed by

23、 the static electricity of the work environment.Be careful to use proper grounding in the area where repairs are being performed.2-1 Ground the workbenchGround the workbench by laying conductive material (such as a conductive sheet) or an iron plate over it before placing the traverse unit (optical

24、pickup) on it.2-2 Ground yourselfUse an anti-static wrist strap to release any static electricity built up in your body.3. Handling the optical pickup1. In order to maintain quality during transport and before installation, both sides of the laser diode on the replacement optical pickup are shorted.

25、 After replacement, return the shorted parts to their original condition. (Refer to the text.)2. Do not use a tester to check the condition of the laser diode in the optical pickup. The testers internal power source can easily destroy the laser diode.4. Handling the CD changer unit (optical pickup)1

26、. Do not subject the CD changer unit (optical pickup) to strong shocks, as it is a sensitive, complex unit.2. Cut off the shorted part of the flexible cable using nippers, etc. after replacing the optical pickup. For specific details, refer to the replacement procedure in the text. Remove the anti-s

27、tatic pin when replacing the CD changer unit. Be careful not to take too long a time when attaching it to the connector.3. Handle the flexible cable carefully as it may break when subjected to strong force.4. It is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not t

28、urn it.Attention when traverse unit is decomposed* Please refer to “Disassembly method” in the text for pick up and how to detach the CD changer mechanism.1. Remove the CD changer unit.2. Disconnect the harness from connector on the CD motor board.3. Solder is put up before the card wire is removed

29、from connector Cn601on the main board as shown in Fig.1 and Fig.2. (When the wire is removed without putting up solder, the CD pick-up assembly might destroy.)4. Please remove solder after connecting the card wire with CN601 when you install picking up in the substrate.Conductive material (conductiv

30、e sheet) or iron plate(caption)Anti-static wrist strapSolderingFig.2Flexible cableFig.1CD changer unitCD changer mechanism assembly MX-GA3V1-5Disassembly methodCommence disassembly of the set by removing the main units and then proceed to the components and assemblies inside the units. Replacement o

31、f the fuses and the power IC? Top cover? CD changer unit? Front panel assembly? Chassis unit? CD changer unit? Removing the main PCB? Removing the CD changer mechanism assembly? Removing the CD pickup? Replacing the loading motor and belt of the CD changer tray? Replacing the CD tray rotor belt of C

32、D changer, and removing the motor? Front panel assembly? Removing the cassette deck mechanism? Removing the earphone jack PCB? Removing the control/FL PCB? Removing the switch PCB and ACTIVE BASS EX. switch PCB? Removing the cassette deck main motor, and replacing the main belts? Removing the leaf s

33、witches of the cassette deck mechanism? Removing the cassette deck heads? Chassis unit? Removing the 3-pin regulator? Removing the power amp and supply PCB and the Power Trans PCB? Removing the sub power PCBMX-GA3V1-6Replacement of the fuses and the power IC? Replacing the fuses (See Fig.1, Fig.3) ?

34、 Prior to performing the following procedure, remove the left side BOARD and remove tuner PCB (Fig.3,BB) 1. Replace the fuses inside.Caution Be sure to use fuses with the specified ratings.? Replacing the heat sink cover (See Fig.3)1. Remove four screws B from the rear panel.2. Pull the heat sink co

35、ver outward.? Replacing the power IC (See Fig.2) ? Prior to performing the following procedure, remove the top cover.1. Remove the two screws A from the heat sink between the power IC.2. Remove the solder fixing the power IC.Fig.3BBBVIDEO OUT110V127V220V230V-240VBottom side Fig.1(A)CN951Fuse(F952)T1

36、.6AL 250VFuse(F951)T2AL 250VFuse(F953)T1.25AL 250VAdd LableT2AL 250VAdd LableT1.25AL 250VComponent side Fig.1(B1)Fuse(F953)T1.25AL 250VAdd LableT1.25AL 250VComponent side Fig.1(B2)Fuse(F951)T2AL 250VFuse(F952)T1.6AL 250VWAFig.2MX-GA3V1-7Fig.5 (A)Fig.5 (B)Left Front panel assemblyRight Front panel as

37、sembly? Removing the top cover (See Fig.4 and 5)1. Remove six screws B that retain the top cover from the panel rear of the body.2. Remove eight screws C and D that retain the top cover from the two sides of the body.3. Remove the top cover from the body by lifting it toward the rear.DDFig.4Top cove

38、rBVIDEO OUT223-2CCMX-GA3V1-8? Removing the CD changer unit(See Fig.6 to 9)? Prior to performing the following procedures, remove the top cover and both sides BOARD.Caution Although the CD mechanism unit can be removed without removing the CD tray panel, it is still recommended to remove it in order

39、to prevent damage.a. From the front panel side of this set, push in the sections marked with arrows and pull out the CD tray toward the front.b. Remove the CD tray panel by pushing both of its extremities upward in the direction of the arrows.c. Push the CD tray deep into the set. 1. Disconnect the

40、cord wires from the CD PCB CN704, CN607, CN1101 and disconnect CN1 (shield wire) from back panel.2. From the rear of the set, remove two screws E and two screws G on the front panel left and right side.3. Handle the CD changer unit rear, take out the unit.Fig.10CD changerunitFig.6CD tray panelFig.7C

41、D tray panelFig.8AccessoryterminalAntennatermianlEFFGMX-GA3V1-9Fig.10HFig.12IPower amp andsupply PCBClaw cGND lug b? Removing the front panel assembly(See Fig.10 to 11)? Prior to performing the following procedures, remove the top cover and both board. ? Also remove the CD changer unit.1. Disconnect

42、 the parallel wire and the cord wire from the connectors CN701, CN702, CN703, CN850 on the power amp. and supply PCB.2. Remove two screws H retaining the front panel assembly onto the bottom of the body.3. Remove two screws I on the left and right side of the set retaining the panel front from the b

43、ottom and then remove then GND lug b that comes from the power amp and supply PCB.4. Disengage the claws c on both sides of the front panel assembly and then remove the assembly.MX-GA3V1-10Fig.14CD PCBShort round CN601? Removing the CD PCB (See Fig.12 to 13)? Prior to performing the following proced

44、ures, remove the top cover and both sides board. ? Also remove the CD changer unit.1. The two screws E that retain the VCD assembly should be removed.2. Disconnect the wires from CN602, CN603, CN604 and CN605 on the CD PCB, which is located on the back side of the CD changer unit.3. The two screws J

45、 that retain the CD PCB should be removed.4. Remove the CD PCB by pulling it toward the side where the CN601 is located.5. Using solder, short the CD pickup to connect to short round.Caution After re-connecting the wires, be sure to remove the shorting solder from the GND connection.6. Disconnect th

46、e card wire from the connector CN601 on the main PCB and then remove the main PCB.Fig.12(A)EFig.12(B)JCD PCBMX-GA3V1-11Fig.14 DFig.16K ( Silver color)K ( copper color)K ( Silver color)K ( copper color)CD changermechanismassembly? Removing the CD changer mechanism assembly (See Fig.14 to 15)? Prior t

47、o performing the following procedures, remove the top cover and both sides board. ? Also remove the CD changer unit.1. Removing screws D from the front chuck base of the CD changer mechanism unit.2. Turn the CD changer mechanism cover base and remove screws E connecting the unit to the CD changer me

48、chanism assembly.3. Removing four screws K retaining the CD mechanism holder assembly.Caution When replacing the CD changer mechanism assembly, be sure not to mistake the positions of the silver color and copper color spring.Fig.15ECD changerunitMX-GA3V1-12Fig.17GFCD pickupShaftFig.19DNOFig.18MLFig.

49、20Motor lockerTurn table motorObligue gear ? Removing the CD pickup (See Fig.17) ? Prior to performing the following procedures, remove the top cover and both sides board. ? Also remove the CD changer unit. ? Also remove the CD changer mechanism.1. Widen the section F.2. While keeping the section F

50、wide open, push the section G in the direction of the arrow to remove the shaft, and then remove the CD pickup.? Replacing the loading motor and rotor belt of the CD changer (See Fig .18)? Prior to performing the following procedures, remove the top cover. ? Also open the CD changer tray.1. Remove t