JVC-MXK50R-cs-sm 维修电路原理图.pdf

《JVC-MXK50R-cs-sm 维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《JVC-MXK50R-cs-sm 维修电路原理图.pdf（70页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUALCOMPACT COMPONENT SYSTEMNo.21122Aug. 2002COPYRIGHT 2002 VICTOR COMPANY OF JAPAN, LTD.MX-K50RMX-K50RContentsSafety PrecautionsImportant for laser productsPreventing static electricityDisassembly method Wiring connectionAdjustment methodFlow of functional operation until TOC readMaintena

2、nce of laser pickupReplacement of laser pickupTrouble shootingDescription of major ICs1-21-41-51-61-181-191-231-241-241-251-2841SP-MXK50SP-MXK50CA-MXK50RDISCSKIPVOLUMEVOLUME+RMSM XK50R R EMOTE CONTROLSTANDBY/ON12345678910+10SLEEPSOUNDMODETAPE A/BFADE MUTINGDISPLAY MODE SELECT +FM /A MAUXCD TAPE ACTI

3、VE BASSEX. LEVELFM MODEPTY/ EONDISC CHANGECD-R/ RW PLAYBACKCLOCK/TIMERDISPLAYPHONESREPEATREC START/ STOPCD REC STARTDUBBINGPROGRAMRANDOMTAPE BTAPE AAUXTAPECDFM / AMACTIVE BASSEX. LEVELSOUNDMODEM X-K50RCD 2CD 3ACTIVE BASS EXTENSIONCD3FULL - LOGIC CONTROLCD SYNCHRO RECORDINGCD 1STANDBY/ONSTANDBYECODIS

4、PLAY MODEPTY/EON SELECT +Area suffixB - U.K.E - Continental EuropeEN - Northern EuropeEV - Eastern EuropeRadioFans.CN 收音机爱 好者资料库MX-K50R1-21. This design of this product contains special hardware and many circuits and components specially for safety purposes. For continued protection, no changes shou

5、ld be made to the original design unless authorized in writing by the manufacturer. Replacement parts must be identical to those used in the original circuits. Services should be performed by qualified personnel only.2. Alterations of the design or circuitry of the product should not be made. Any de

6、sign alterations of the product should not be made. Any design alterations or additions will void the manufacturers warranty and will further relieve the manufacture of responsibility for personal injury or property damage resulting therefrom.3. Many electrical and mechanical parts in the products h

7、ave special safety-related characteristics. These characteristics are often not evident from visual inspection nor can the protection afforded by them necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special safety cha

8、racteristics are identified in the Parts List of Service Manual. Electrical components having such features are identified by shading on the schematics and by ( ) on the Parts List in the Service Manual. The use of a substitute replacement which does not have the same safety characteristics as the r

9、ecommended replacement parts shown in the Parts List of Service Manual may create shock, fire, or other hazards.4. The leads in the products are routed and dressed with ties, clamps, tubings, barriers and the like to be separated from live parts, high temperature parts, moving parts and/or sharp edg

10、es for the prevention of electric shock and fire hazard. When service is required, the original lead routing and dress should be observed, and it should be confirmed that they have been returned to normal, after re-assembling.5. Leakage currnet check (Electrical shock hazard testing)After re-assembl

11、ing the product, always perform an isolation check on the exposed metal parts of the product (antenna terminals, knobs, metal cabinet, screw heads, headphone jack, control shafts, etc.) to be sure the product is safe to operate without danger of electrical shock.Do not use a line isolation transform

12、er during this check.Plug the AC line cord directly into the AC outlet. Using a Leakage Current Tester, measure the leakage current from each exposed metal parts of the cabinet, particularly any exposed metal part having a return path to the chassis, to a known good earth ground. Any leakage current

13、 must not exceed 0.5mA AC (r.m.s.).Alternate check methodPlug the AC line cord directly into the AC outlet. Use an AC voltmeter having, 1,000 ohms per volt or more sensitivity in the following manner. Connect a 1,500 10W resistor paralleled by a 0.15 F AC-type capacitor between an exposed metal part

14、 and a known good earth ground.Measure the AC voltage across the resistor with the AC voltmeter. Move the resistor connection to each exposed metal part, particularly any exposed metal part having a return path to the chassis, and meausre the AC voltage across the resistor. Now, reverse the plug in

15、the AC outlet and repeat each measurement. Voltage measured any must not exceed 0.75 V AC (r.m.s.). This corresponds to 0.5 mA AC (r.m.s.). 1. This equipment has been designed and manufactured to meet international safety standards.2. It is the legal responsibility of the repairer to ensure that the

16、se safety standards are maintained.3. Repairs must be made in accordance with the relevant safety standards.4. It is essential that safety critical components are replaced by approved parts.5. If mains voltage selector is provided, check setting for local voltage.Good earth groundPlace this probe on

17、 each exposedmetal part.AC VOLTMETER(Having 1000 ohms/volts,or more sensitivity)1500 10W0.15 F AC TYPE!Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system.In regard with component parts appe

18、aring on the silk-screen printed side (parts side) of the PWB diagrams, the parts that are printed over with black such as the resistor ( ), diode ( ) and ICP ( ) or identified by the mark nearby are critical for safety. (This regulation does not correspond to J and C version.)RadioFans.CN 收音机爱 好者资料

19、库1-3MX-K50R1. Service should be performed by qualified personnel only.2. This equipment has been designed and manufactured to meet international safety standards.3. It is the legal responsibility of the repairer to ensure that these safety standards are maintained.4. Repairs must be made in accordan

20、ce with the relevant safety standards.5. It is essential that safety critical components are replaced by approved parts.6. If mains voltage selector is provided, check setting for local voltage.1. This design of this product contains special hardware and many circuits and components specially for sa

21、fety purposes. For continued protection, no changes should be made to the original design unless authorized in writing by the manufacturer. Replacement parts must be identical to those used in the original circuits. 2. Any unauthorised design alterations or additions will void the manufacturers guar

22、antee ; furthermore the manufacturer cannot accept responsibility for personal injury or property damage resulting therefrom.3. Essential safety critical components are identified by ( ) on the Parts List and by shading on the schematics, and must never be replaced by parts other than those listed i

23、n the manual. Please note however that many electrical and mechanical parts in the product have special safety related characteristics. These characteristics are often not evident from visual inspection. Parts other than specified by the manufacturer may not have the same safety characteristics as t

24、he recommended replacement parts shown in the Parts List of the Service Manual and may create shock, fire, or other hazards.4. The leads in the products are routed and dressed with ties, clamps, tubings, barriers and the like to be separated from live parts, high temperature parts, moving parts and/

25、or sharp edges for the prevention of electric shock and fire hazard. When service is required, the original lead routing and dress should be observed, and it should be confirmed that they have been returned to normal, after re-assembling.!Burrs formed during molding may be left over on some parts of

26、 the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system.(U.K only)MX-K50R1-4Important for laser products1.CLASS 1 LASER PRODUCT2.DANGER : Invisible laser radiation when open and inter lock failed or defeated. Avoid direct exposure to beam.3.CAUTION : Ther

27、e are no serviceable parts inside theLaser Unit. Do not disassemble the Laser Unit. Replace the complete Laser Unit if it malfunctions.4.CAUTION : The compact disc player uses invisible laser radiation and is equipped with safety switches which prevent emission of radiation when the drawer is open a

28、nd the safety interlocks have failed or are defeated. It is dangerous to defeat the safety switches.5.CAUTION : If safety switches malfunction, the laser is able to function.6.CAUTION : Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardou

29、s radiation exposure.!Please use enough caution not to see the beam directly or touch it in case of an adjustment or operationcheck.Position of labelsWARNING LABELCLASS 1LASER PRODUCT1-5MX-K50RPreventing static electricity1. Grounding to prevent damage by static electricity Electrostatic discharge (

30、ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.2. About the earth processing for the destruction prevention by static electricity In the eq

31、uipment which uses optical pick-up (laser diode), optical pick-up is destroyed by the static electricity of the work environment.Be careful to use proper grounding in the area where repairs are being performed. 2-1 Ground the workbench Ground the workbench by laying conductive material (such as a co

32、nductive sheet) or an iron plate over it before placing the traverse unit (optical pickup) on it.2-2 Ground yourself Use an anti-static wrist strap to release any static electricity built up in your body. 3. Handling the optical pickup1. In order to maintain quality during transport and before insta

33、llation, both sides of the laser diode on the replacement optical pickup are shorted. After replacement, return the shorted parts to their original condition. (Refer to the text.)2. Do not use a tester to check the condition of the laser diode in the optical pickup. The testers internal power source

34、 can easily destroy the laser diode. 4. Handling the traverse unit (optical pickup)1. Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit. 2. Cut off the shorted part of the flexible cable using nippers, etc. after replacing the optical pickup. For

35、specific details, refer to the replacement procedure in the text. Remove the anti-static pin when replacing the traverse unit. Be careful not to take too long a time when attaching it to the connector. 3. Handle the flexible cable carefully as it may break when subjected to strong force. 4. It is no

36、t possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn itConductive material (conductive sheet) or iron plate(caption)Anti-static wrist strapAttention when CD mechanism assembly is decomposed1. Remove the CD changer unit. 2. Remove the CD changer mechanism. 3. Solder

37、is put up before the card wire is removed from the pickup unit connector on the CD mechanism assembly. (When the card wire is removed without putting up solder, the CD pick-up assembly might destroy.) 4. Please remove solder after connecting the card wire with the pickup unit connector when you inst

38、all picking up in the substrate.*Please refer to Disassembly method in the text for pick-up and how to detach the CD mechanism assembly. SolderingFig.1Fig.2Card wireCard wirePicup unitconnectorPicup unitconnectorCD changer unitCD changer mechanismMX-K50R1-6Remove the three screws A attaching the met

39、al cover on the back of the body. Remove the six screws B attaching the metal cover on both sides of the body.Remove the metal cover from the body by lifting the rear part of the cover.1.2.3.Disassembly methodRemoving the metal cover (See Fig.1) ONE POINT How to eject the CD tray (see fig.2)Although

40、 it will end if the OPEN/CLOSE button is pushed when a power supply can be taken, when that is not right, CD tray will be opened manually.Turn the loading pulley gear at the bottom of the CD changer unit as shown in Fig.2 and draw the CD tray toward the front. Removing the CD tray fitting(See Fig. 3

41、)Prior to performing the following procedure, eject the CD tray.After drawing the lower part of the tray fitting toward the front, remove the five claws. Then, while moving the tray fitting upward, remove it.1.Prior to performing the following procedure, remove the metal cover and CD tray fitting.Re

42、move the card wire attached to CD changer unit on the adhesion tape.Disconnect the card wire from the connector CW105 on the CD board.Disconnect the harness from the connector RCW6 on the main board and CW107 on the CD board.Remove the two screws C attaching the CD changer unit to the rear panel.Rem

43、ove the two screws D attaching the CD changer unit to both sides of the front panel assembly.Draw the CD changer unit upward from behind while pulling the rear panel outward. 1.2.3.4.5.6.Removing the CD changer unit (See Fig.4 to 7)Fig.1Fig.2Fig.3Metal coverAB(both sides) Loading pulley gear(See fig

44、.1)Fig.4CD changer unitCard wireAdhesion tapeJoint ClawCD tray fitting1-7MX-K50RPrior to performing the following procedure, remove the metal cover and the CD changer unit.Disconnect the card wire from the connector FCW3 on the main board.Disconnect the harness from the connector JCW1, JCW2 and HCW3

45、 on the main board.Remove the screw E attaching the earth terminal extending from the cassette mechanism assembly. Remove the two screws F attaching the front panel assembly to both sides of the body.Remove the screw G attaching the main board to the front panel assembly.Remove the screw H attaching

46、 the front panel assembly to bottom of the body.Release the two joints1 and two joints2, and detach the front panel assembly toward the front.1.2.3.4.5.6.7.Removing the front panel assembly (See Fig.8 to 10)Fig.6Fig.7Fig.5RCW6CD changer unitMain boardRear panelCD(both sides)Rear panelCD changer unit

47、Front panelassemblyFig.8Fig.9Main boardAmp. boardFCW3JCW2JCW1HCW3ACW1ACW2Front panelassemblyJoint1(both sides)F(both sides)Joint1(both sides)F(both sides)E(fixing the earth wire)Front panelassemblyGMain boardCD boardCW105CW107MX-K50R1-8Prior to performing the following procedure, remove the metal co

48、ver and the CD changer unit.Disconnect the card wire from the connector ACW1 and the harness from the connector ACW2 on the amp. board. Remove the four screws I attaching the heat sink cover to the rear panel. Remove the heat sink cover.Remove the four screws J attaching the heat sink and two screws

49、 K attaching the speaker terminal to the rear panel. After moving the heat sink upward, remove the claws. Then pull out the heat sink & amp. board inward.1.2.3.4.Removing the heat sink & amp. board (See Fig.8, 11 and 12)Prior to performing the following procedure, remove the metal cover.Disconnect t

50、he card wire from the connector CON01 on the tuner board.Remove the two screws L attaching the tuner board to the rear panel. 1.2.Removing the tuner board (See Fig.12 and 13)Prior to performing the following procedure, remove the metal cover, CD changer unit and heat sink & amp. board.Disconnect the