JVC-MXG68V-cs-sm 维修电路原理图.pdf

《JVC-MXG68V-cs-sm 维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《JVC-MXG68V-cs-sm 维修电路原理图.pdf（89页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUALCOMPACT COMPONENT SYSTEM?No.20995Jul. 2001COPYRIGHT 2001 VICTOR COMPANY OF JAPAN, LTD.MX-G68VMX-G65VMX-G68V/MX-G65VArea Suffix USSingaporeSafety precautionsPreventing static electricityImportant for laser productsDisassembly methodWiring connection Adjustment method1-21-31-41-51-18?1-1

2、9Flow of functional operation until TOC readMaintenance of laser pickupReplacement of laser pickupTroubleshootingDescription of major ICs 1-231-241-241-251-3352ContentsCA-MXG68VCA-MXG65VCANCEL/DEMOPRESETPLAY & EXCHANGESTANDBY/ONSTANDBYDISC CHANGESOUNDMODESUBWOOFERLEVELCD-R/RW PLAYBACKCOMPACT COMPONE

3、NT SYSTEMMX-G65VCLOCK/TIMERDISPLAYPHONESREPEATPROGRAMREC START/STOPCDREC STARTDUBBINGTAPE ATUNINGSETTAPE BRANDOMEJECTPLAYFULL - LOGIC CONTROLAEJECTREC/PLAYCD SYNCHRO RECORDINGBPREVNEXTRETURNPBCVCD NUMBERCOMPACTDIGITAL VIDEOVIDEO CDSELECTDISC SKIPVOLUMEVOLUME+RMSMXG65VU REMOTE CONTROLSTANDBY/ON123456

4、78910+10KEY CONTROLSUBWOOFERLEVELSOUNDMODEFM MODE/TAPE A/BFADE MUTINGFM/AMCD TAPE KARAOKEECHOPREV.NEXTRETURNSLEEPON SCREENV.INTROHIGHLIGHTSLOWAUX STILLSELECTCA-MXG65VSP-MXG65VSP-MXG65VVIDEO CDPlayBackControlModelColorUXSaudi ArabiaSilverShanpagne-goldRadioFans.CN 收音机爱 好者资料库MX-G68V/MX-G65V1-21. This

5、design of this product contains special hardware and many circuits and components specially for safety purposes. For continued protection, no changes should be made to the original design unless authorized in writing by the manufacturer. Replacement parts must be identical to those used in the origi

6、nal circuits. Services should be performed by qualified personnel only.2. Alterations of the design or circuitry of the product should not be made. Any design alterations of the product should not be made. Any design alterations or additions will void the manufacturers warranty and will further reli

7、eve the manufacture of responsibility for personal injury or property damage resulting therefrom.3. Many electrical and mechanical parts in the products have special safety-related characteristics. These characteristics are often not evident from visual inspection nor can the protection afforded by

8、them necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified in the Parts List of Service Manual. Electrical components having such features are identified by shading on the schem

9、atics and by ( ) on the Parts List in the Service Manual. The use of a substitute replacement which does not have the same safety characteristics as the recommended replacement parts shown in the Parts List of Service Manual may create shock, fire, or other hazards.4. The leads in the products are r

10、outed and dressed with ties, clamps, tubings, barriers and the like to be separated from live parts, high temperature parts, moving parts and/or sharp edges for the prevention of electric shock and fire hazard. When service is required, the original lead routing and dress should be observed, and it

11、should be confirmed that they have been returned to normal, after re-assembling.5. Leakage current check (Electrical shock hazard testing)After re-assembling the product, always perform an isolation check on the exposed metal parts of the product (antenna terminals, knobs, metal cabinet, screw heads

12、, headphone jack, control shafts, etc.) to be sure the product is safe to operate without danger of electrical shock.Do not use a line isolation transformer during this check.Plug the AC line cord directly into the AC outlet. Using a Leakage Current Tester, measure the leakage current from each expo

13、sed metal parts of the cabinet, particularly any exposed metal part having a return path to the chassis, to a known good earth ground. Any leakage current must not exceed 0.5mA AC (r.m.s.).Alternate check methodPlug the AC line cord directly into the AC outlet. Use an AC voltmeter having, 1,000 ohms

14、 per volt or more sensitivity in the following manner. Connect a 1,500 10W resistor paralleled by a 0.15 F AC-type capacitor between an exposed metal part and a known good earth ground.Measure the AC voltage across the resistor with the AC voltmeter. Move the resistor connection to each exposed meta

15、l part, particularly any exposed metal part having a return path to the chassis, and measure the AC voltage across the resistor. Now, reverse the plug in the AC outlet and repeat each measurement. Voltage measured any must not exceed 0.75 V AC (r.m.s.). This corresponds to 0.5 mA AC (r.m.s.). 1. Thi

16、s equipment has been designed and manufactured to meet international safety standards.2. It is the legal responsibility of the repairer to ensure that these safety standards are maintained.3. Repairs must be made in accordance with the relevant safety standards.4. It is essential that safety critica

17、l components are replaced by approved parts.5. If mains voltage selector is provided, check setting for local voltage.Good earth groundPlace this probe on each exposedmetal part.AC VOLTMETER(Having 1000 ohms/volts,or more sensitivity)1500 10W0.15 F AC TYPE!Burrs formed during molding may be left ove

18、r on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system.In regard with component parts appearing on the silk-screen printed side (parts side) of the PWB diagrams, the parts that are printed over with black such as the resistor ( ), diode

19、 ( ) and ICP ( ) or identified by the mark nearby are critical for safety. When replacing them, be sure to use the parts of the same type and rating as specified by the manufacturer. (Except the J&C version)RadioFans.CN 收音机爱 好者资料库MX-G68V/MX-G65V1-3Preventing static electricity1. Grounding to prevent

20、 damage by static electricity Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.2. About the earth processing for the

21、 destruction prevention by static electricity In the equipment which uses optical pick-up (laser diode), optical pick-up is destroyed by the static electricity of the work environment.Be careful to use proper grounding in the area where repairs are being performed. 2-1 Ground the workbench Ground th

22、e workbench by laying conductive material (such as a conductive sheet) or an iron plate over it before placing the traverse unit (optical pickup) on it.2-2 Ground yourself Use an anti-static wrist strap to release any static electricity built up in your body. 3. Handling the optical pickup1. In orde

23、r to maintain quality during transport and before installation, both sides of the laser diode on the replacement optical pickup are shorted. After replacement, return the shorted parts to their original condition. (Refer to the text.)2. Do not use a tester to check the condition of the laser diode i

24、n the optical pickup. The testers internal power source can easily destroy the laser diode. 4. Handling the traverse unit (optical pickup)1. Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit. 2. Cut off the shorted part of the flexible cable using

25、 nippers, etc. after replacing the optical pickup. For specific details, refer to the replacement procedure in the text. Remove the anti-static pin when replacing the traverse unit. Be careful not to take too long a time when attaching it to the connector. 3. Handle the flexible cable carefully as i

26、t may break when subjected to strong force. 4. It is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn itConductive material (conductive sheet) or iron plate(caption)Anti-static wrist strapAttention when CD mechanism assembly is decomposed1. Remove the CD chang

27、er unit. 2. Remove the CD holder mechanism. 3. Solder is put up before the card wire is removed from the pickup unit connector on the CD mechanism assembly. (When the card wire is removed without putting up solder, the CD pick-up assembly might destroy.) 4. Please remove solder after connecting the

28、card wire with the pickup unit connector when you install picking up in the substrate.*Please refer to Disassembly method in the text for pick-up and how to detach the CD mechanism assembly. SolderingFig.1Fig.2Card wireCard wirePickup unitconnectorPickup unitconnectorCD changer unitCD holder mechani

29、smMX-G68V/MX-G65V1-4Important for laser products1.CLASS 1 LASER PRODUCT2.DANGER : Invisible laser radiation when open and inter lock failed or defeated. Avoid direct exposure to beam.3.CAUTION : There are no serviceable parts inside theLaser Unit. Do not disassemble the Laser Unit. Replace the compl

30、ete Laser Unit if it malfunctions.4.CAUTION : The compact disc player uses invisible laserradiation and is equipped with safety switches whichprevent emission of radiation when the drawer is open and the safety interlocks have failed or are de feated. It is dangerous to defeat the safety switches.5.

31、CAUTION : If safety switches malfunction, the laser is able to function.6.CAUTION : Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.Position of labelsWARNING LABEL!CAUTIONPlease use enough caution not to see the b

32、eam directly or touch it in case of an adjustment or operationcheck.CLASS 1LASER PRODUCTMX-G68V/MX-G65V1-5Remove the three screws A attaching the metal cover on the back of the body. Remove the six screws B attaching the metal cover on both sides of the body.Remove the metal cover from the body by l

33、ifting the rear part of the cover.1.2.3.Disassembly methodRemoving the metal cover (See Fig.1 and 2)Do not break the front panel tab fitted to the metal cover.ATTENTION: Prior to performing the following procedure, remove the metal cover.Disconnect the card wire which is attached with adhesive to th

34、e left side of the CD changer unit.Disconnect the harness from connector CW1 and CW7 on the back of the video CD board.Disconnect the harness from connector RCW6 on the main board.Disconnect the card wire from connector UCW3 on the FL dispaly & system control board.Remove the two screws C attaching

35、the CD changer unit on the rear panel. Remove the two screws D attaching the CD changer unit on the side body.Draw the CD changer unit upward from behind while pulling the rear panel outward. 1.2.3.4.5.6.7.Removing the CD changer unit (See Fig.3 to 6)Fig.1Fig.2Fig.3Metal coverAAAMetal coverBBRear pa

36、nelFront panel assembly(Bottom side)(Bottom side)(Bottom side) Video CD boardCD changer unitCW1CW7MX-G68V/MX-G65V1-6Prior to performing the following procedure, remove the metal cover and the CD changer unit.Disconnect the card wire from connector FCW3 and the harness from connector JCW1, JCW2 ECW1

37、and HCW3 on the inner side of the main board in the body.Remove the two screws E attaching the front panel assembly on both sides of the body.Remove the screw F attaching the earth terminal extending from the cassette mechanism assembly. Remove the screw G attaching the front panel assembly and main

38、 board.Remove the screw H attaching the front panel assembly on the bottom of the body.Release the two joints a on both sides and two joints b on the bottom of the body using a screwdriver. 1.2.3.4.5.6.Removing the front panel assembly (See Fig.7 to 9 )Rear panelCDDRear panelRear panelFront panel as

39、semblyAdhesive card wire strapCD changer unitCD changer unitFig.7Main boardFCW3JCW2JCW1HCW3Front panel assemblyJoint aEarth wireEFECW1Fig.4Fig.5Fig.6aFig.6bUCW3Front panel assemblyFLdispaly & system control boardRCW6MX-G68V/MX-G65V1-7Prior to performing the following procedure, remove the metal cove

40、r and the CD changer unit.Remove the four screws I attaching the heat sink cover to the rear panel on the back of the body. Remove the four screws J attaching the heat sink & amplifier board to the rear panel on the back of the body. Remove the two screws K attaching the speaker terminal to the rear

41、 panel on the back of the body. Disconnect the card wire from connector ACW1 and the harness from connector ACW2 on the amplifier board. After moving the heat sink upward, remove the claws. Then pull out the heat sink & amplifier board .1.2.3.4.5.Removing the heat sink & amplifier board (See Fig.10

42、to 12)Fig.8Fig.9Front panel assemblyGEMain boardHJoint bJoint bJoint cBottom sideFig.10Fig.11Rear panelHeat sink coverHeat sink Speaker terminal Tuner terminal KLIIJJFig.12ACW1Rear panelAmplifier boardACW2MX-G68V/MX-G65V1-8Prior to performing the following procedure, remove the metal cover and CD ch

43、anger unit.Disconnect the card wire from connector CON01 on the tuner board.Remove the two screws L attaching the tuner board. 1.2.Removing the tuner board(See Fig.11 and 13)Prior to performing the following procedure, remove the metal cover, CD changer unit, heat sink & amplifier board and tuner bo

44、ard.Remove the one screw M, three screws N and three screws N attaching the rear panel.Removing the rear panel (See Fig.14)1.Prior to performing the following procedure, remove the metal cover, CD changer unit, heat sink & amplifier board, tuner board and rear cover.Disconnect the card wire from con

45、nector FCW3 and the harness from connector JCW1, JCW2, ECW1 and HCW3 on the main board. Disconnect the harness from connector PCW1 on the power transformer board.Remove the screw G attaching the main board holder. (See Fig.8)Remove the two screws O attaching the heat sink and bottom chassis. 1.2.3.4

46、.Removing the main Board (See Fig. 15)Main boardTuner boardCON01NMFig.14Rear panelFig.13NFig.15Transformer boardOFCW3JCW2JCW1HCW3PCW1Main boardECW1Rear panelMX-G68V/MX-G65V1-9Prior to performing the following procedure, remove the metal cover, CD changer unit, heat sink & amplifier board .Remove the

47、 four screws P attaching the power ICs to the heat sink.Unsolder the power ICs solder point.1.2.Removing the power ICs (See Fig.16 and 17)Prior to performing the following procedure, remove the metal cover, CD changer unit, heat sink & amplifier board, tuner board and rear cover.Disconnect the power

48、 cord from connector RCW2 of the power transformer board.Disconnect the harness from connector PCW1 of the power transformer board.Remove the four screws Q attaching the power transformer.1.2.3.Removing the power transformer (See Fig.18)Fig.17Fig.16PHeat sinkAmplifier boardHeat sinkPower ICs solder

49、pointFig.18QPower cordRCW2PCW1Power transformerQMX-G68V/MX-G65V1-10Disconnect the card wire from the connectors UCW3, UCW5,UCW6 and UJW5 on the FL display & system control board.Remove the five screws S attaching the FL display & system board. Disconnect the card wire from the connector UCW2 on the

50、FL display & system control board.1.2.3.Removing the FL display & system control board (See Fig.19)Disconnect the card wire from connector UCW1 of the power switch board. Remove the five screws R attaching the power switch board and release the tab c outward. 1.2.Prior to performing the following pr