JVC-MXSK1-cs-sm 维修电路原理图.pdf

《JVC-MXSK1-cs-sm 维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《JVC-MXSK1-cs-sm 维修电路原理图.pdf（36页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUALCOPYRIGHT 2004 VICTOR COMPANY OF JAPAN, LIMITEDNo.MB2072004/4COMPACT COMPONENT SYSTEMMB20720043MX-SK1TABLE OF CONTENTS1PRECAUTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-32SPECIFI

2、C SERVICE INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-53DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-64ADJUSTME

3、NT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-305TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-34

4、COMPACTDIGITAL AUDIOCOMPACTDIGITAL VIDEOPHONESACTIVEBASS EX.EJECTEJECTDISCSELECTSELECTM X - S K 3COMPACTDIGITAL VIDEOVOLUMESTANDBY/ONFM MODEAUXSLEEPFM/AMVIDEO INTROPREV.NEXTHIGHLIGHTON SCREENSETENTERRETURNPBCSTILLKEY CONTROLDISC 1DISC 2DISC 3DISCREPEATPROGRAM RANDOMPROGRAMCANCELSOUNDTURBOSOUNDMODEAC

5、TIVEBASS EX.TAPE-AKARAOKEMPXECHOFADEMUTINGTAPE-BVOLUMEREMOTE CONTROLSTART/STOPRECCA-MXSK1SP-MXSK1SP-MXSK1EE - Russian FederationArea suffixRadioFans.CN 收音机爱 好者资料库1-2 (No.MB207)SPECIFICATIONDesign & specifications are subject to change without notice.Amplifier sectionOutput PowerMAIN SPEAKERS64 W per

6、 channel min. RMS both channels driven into6 at 1 kHz with no more than 0.9% total harmonicdistortion.Audio input sensitivity/Impedance(Measured at 1 kHz with tape record-ing signal 300 mV)AUX400 mV/50 kMIC3 mV/10 kTunerFM tuning range87.50 MHz to 108.00 MHzAM tuning rangeAt 9 kHz intervals531 kHz t

7、o 1 710 kHzAt 10 kHz intervals530 kHz to 1 710 kHzCD playerCD capacity3 CDsDynamic range85 dBSignal-to-noise ratio90 dBWow and flutterImmeasurableCassette deckFrequency response Normal (type I) 50 Hz to 14 000 HzWow and flutter0.15% (WRMS)GeneralPower requirementAC 110 V / AC 127 V / AC 220 V / AC 2

8、30 V to AC 240 V (adjustable with the voltage selector)Power consumption50 Hz / 60 Hz100 W (at operation)20 W (on standby)Dimensions (approx.)270 mm x 306 mm x 433.5 mm (W/H/D)Mass (approx.)9.2 kgSpeaker SpecificationsType3-Way 3 Speaker Bass-Reflex (Magnetically-Shielded Type)SpeakersMain woofer15c

9、m cone x 1Mid Range5.0cm cone x 1Tweeter2.0cm dome x 1Power Handling Capacity80 WImpedance6 Frequency Range42 Hz to 30 000HzSound Pressure Level84 dB/W.mDimensions (W x H xD)215mm x 306 mm x 243 mmMass3.4 kgRadioFans.CN 收音机爱 好者资料库(No.MB207)1-3SECTION 1PRECAUTION1.1Safety Precautions(1) This design o

10、f this product contains special hardware andmany circuits and components specially for safety purpos-es. For continued protection, no changes should be madeto the original design unless authorized in writing by themanufacturer. Replacement parts must be identical tothose used in the original circuit

11、s. Services should be per-formed by qualified personnel only.(2) Alterations of the design or circuitry of the product shouldnot be made. Any design alterations of the product shouldnot be made. Any design alterations or additions will voidthe manufacturers warranty and will further relieve themanuf

12、acture of responsibility for personal injury or propertydamage resulting therefrom.(3) Many electrical and mechanical parts in the products havespecial safety-related characteristics. These characteris-tics are often not evident from visual inspection nor can theprotection afforded by them necessari

13、ly be obtained by us-ing replacement components rated for higher voltage, watt-age, etc. Replacement parts which have these specialsafety characteristics are identified in the Parts List of Ser-vice Manual. Electrical components having such featuresare identified by shading on the schematics and by

14、( ) onthe Parts List in the Service Manual. The use of a substitutereplacement which does not have the same safety charac-teristics as the recommended replacement parts shown inthe Parts List of Service Manual may create shock, fire, orother hazards.(4) The leads in the products are routed and dress

15、ed with ties,clamps, tubings, barriers and the like to be separated fromlive parts, high temperature parts, moving parts and/orsharp edges for the prevention of electric shock and firehazard. When service is required, the original lead routingand dress should be observed, and it should be confirmedt

16、hat they have been returned to normal, after reassem-bling.(5) Leakage shock hazard testingAfter reassembling the product, always perform an isola-tion check on the exposed metal parts of the product (an-tenna terminals, knobs, metal cabinet, screw heads,headphone jack, control shafts, etc.) to be s

17、ure the productis safe to operate without danger of electrical shock.Do notuse a line isolation transformer during this check. Plug the AC line cord directly into the AC outlet. Using aLeakage Current Tester, measure the leakage currentfrom each exposed metal parts of the cabinet, particular-ly any

18、exposed metal part having a return path to thechassis, to a known good earth ground. Any leakage cur-rent must not exceed 0.5mA AC (r.m.s.). Alternate check methodPlug the AC line cord directly into the AC outlet. Use anAC voltmeter having, 1,000 per volt or more sensitivityin the following manner.

19、Connect a 1,500 10W resistorparalleled by a 0.15F AC-type capacitor between an ex-posed metal part and a known good earth ground.Measure the AC voltage across the resistor with the ACvoltmeter. Move the resistor connection to each exposed metalpart, particularly any exposed metal part having a retur

20、npath to the chassis, and measure the AC voltage acrossthe resistor. Now, reverse the plug in the AC outlet andrepeat each measurement. Voltage measured any mustnot exceed 0.75 V AC (r.m.s.). This corresponds to 0.5mA AC (r.m.s.). 1.2Warning(1) This equipment has been designed and manufactured tomee

21、t international safety standards.(2) It is the legal responsibility of the repairer to ensure thatthese safety standards are maintained.(3) Repairs must be made in accordance with the relevantsafety standards.(4) It is essential that safety critical components are replacedby approved parts.(5) If ma

22、ins voltage selector is provided, check setting for localvoltage.1.3CautionBurrs formed during molding may be left over on some partsof the chassis. Therefore, pay attention to such burrs in the case of pre-forming repair of this system.1.4Critical parts for safetyIn regard with component parts appe

23、aring on the silk-screenprinted side (parts side) of the PWB diagrams, the parts that areprinted over with black such as the resistor ( ), diode ( )and ICP ( ) or identified by the mark nearby are criticalfor safety. When replacing them, be sure to use the parts of thesame type and rating as specifi

24、ed by the manufacturer. (This regulation dose not Except the J and C version)Good earth groundPlace this probe on each exposedmetal part.AC VOLTMETER(Having 1000 ohms/volts,or more sensitivity)1500 10W0.15 F AC TYPE1-4 (No.MB207)1.5Preventing static electricityElectrostatic discharge (ESD), which oc

25、curs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laserdiode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.1.5.1 Grounding to prevent damage by static electricityStatic electricity in the work area can destroy the

26、optical pickup (laser diode) in devices such as CD players. Be careful to use proper grounding in the area where repairs are being performed. (1) Ground the workbenchGround the workbench by laying conductive material (such as a conductive sheet) or an iron plate over it before placing thetraverse un

27、it (optical pickup) on it.(2) Ground yourselfUse an anti-static wrist strap to release any static electricity built up in your body. (3) Handling the optical pickup In order to maintain quality during transport and before installation, both sides of the laser diode on the replacement opticalpickup a

28、re shorted. After replacement, return the shorted parts to their original condition. (Refer to the text.) Do not use a tester to check the condition of the laser diode in the optical pickup. The testers internal power source can easilydestroy the laser diode. 1.6Handling the traverse unit (optical p

29、ickup)(1) Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit. (2) Cut off the shorted part of the flexible cable using nippers, etc. after replacing the optical pickup. For specific details, refer to thereplacement procedure in the text. Remove the

30、 anti-static pin when replacing the traverse unit. Be careful not to take too longa time when attaching it to the connector. (3) Handle the flexible cable carefully as it may break when subjected to strong force. (4) I t is not possible to adjust the semi-fixed resistor that adjusts the laser power.

31、 Do not turn it.1.7Attention when traverse unit is decomposed*Please refer to Disassembly method in the text for the CD pickup unit. Apply solder to the short land sections before the flexible wire is disconnected from the connecto on the CD servo board. (If theflexible wire is disconnected without

32、applying solder, the CD pickup may be destroyed by static electricity.) In the assembly, be sure to remove solder from the short land sections after connecting the flexible wire.1MConductive material(conductive sheet) or iron palate(caption)Anti-static wrist strap(No.MB207)1-5SECTION 2SPECIFIC SERVI

33、CE INSTRUCTIONSThis service manual does not describe SPECIFIC SERVICE INSTRUCTIONS.1-6 (No.MB207)SECTION 3DISASSEMBLY3.1Main body3.1.1Removing the metal cover(See Fig.13)(1) Remove the six screws A on the back of the main body.(2) Remove the four screws B on each side of the body. (3) Remove the met

34、al cover from the body by lifting the rearpart of the cover.CAUTION :Do not break the front panel tab fitted to the metal cover.Fig.1Fig.2Fig.3AAABB(No.MB207)1-73.1.2Removing the CD fitting(See Fig.46) Prior to performing the following procedure, remove the metalcover.ATTENTION : Be sure to remove t

35、he CD tray fitting before removing theCD changer unit.(1) Press the STANDBY button. Press the OPEN/CLOSE but-ton to eject the CD trey.(2) Move the CD trey fitting upward and release the joint a.(3) Press the OPEN/ CLOSE button to insert the tray.Fig.4Fig.5Fig.6CD traySTANDBY / ON buttonOPEN / CLOSE

36、buttonCD tray fittingJoint aJoint aCD tray1-8 (No.MB207)3.1.3Removing the CD fitting(See Fig.57) How to eject the CD trey without turning on power.(1) Turn the loading pulley gear marked b from the back ofthe CD changer unit as shown in Fig.7 and draw the CDtray toward the front.(2) Move the CD tray

37、 fitting upward and release the joint a.(3) Push and insert the CD tray manually.Fig.73.1.4Removing the CD changer unit(See Fig.8 10) Prior to performing the following procedure, remove the metalcover and the CD fitting.(1) Disconnect the wire from connector CN13 on the mainboard.(2) On the right si

38、de of the body, disconnect the card wire fromconnector CN651 on the CD board in the bottom of the CDchanger unit.(3) Remove the four screws D attaching the CD changer uniton both sides of the body.(4) Remove the three screws E on the back of the body.(5) Move the CD changer unit in the direction of

39、the arrow withpulling the rear panel and the front panel assembly out-ward.Fig.8Fig.9Fig.10Marked bLoading pulley gearDFront panel assemblyMain borad(CN13)Rear panelCN651CD changer unitDFront panel assemblyMain borad(CN13)Rear panelCN651CD changer unitEERear panel(No.MB207)1-93.1.5Removing the CD bo

40、ard(See Fig.1113) Prior to performing the following procedure, remove the metalcover and the CD changer unit.Caution :Before disconnecting the card wire extending from the CDpickup, make sure to solder the short-circuit point on the CDpickup(Fig.12 and 13). If you do not follow this instruction,the

41、CD pickup may be damaged.(1) Remove the four screws F attaching the CD board on thebottom of the CD changer unit.(2) Turn and move the CD board as shown in Fig.12.(3) Disconnect the wire from the CD mechanism board.(4) Solder the short-circuit point on the CD pickup section.(5) Disconnect the card w

42、ire from CN601 on the CD board.Caution :When reassembling, unsolder the short-circuit point after con-necting the card wire to CN601 on the CD board.Fig.11Fig.12Fig.13CD boardCD mechanism boardCD changer unitFFCD mechanisum boardCD board (CN601)Short round(Short-circuit)Pick upCard wireShort round(s

43、hort-circuit)1-10 (No.MB207)3.1.6Removing the front panel assembly(See Fig.1416) Prior to performing the following procedure, remove the metalcover and the CD changer unit.(1) Disconnect the card wire from the connector CN315,CN316 and CN870 on the main board. (2) Disconnect the wire from connector

44、CN702 on the speakerboard and remove the band attaching the wire to the mainboard.(3) Disconnect the wire from the connector CN214 on powertransformer board.(4) Remove the two screws G attaching the front panel as-sembly on the bottom of the body.(5) Remove the two joints d and e on the lower part o

45、f thesides using a screwdriver, and remove the front panel as-sembly toward the front.Fig.14Fig.15Fig.16Main boardCN870Speaker boardCN702Front panel assemblyCN315BanddCN316Power transformer boardCN214Front panel assemblyeGFront panel assembly(No.MB207)1-113.1.7Removing the tuner pack assembly(See Fi

46、g.1718) Prior to performing the following procedure, remove the metalcover and the CD changer unit.(1) Disconnect the card wire from the connector CN1 on thetuner pack assembly on the right side of the body.(2) Remove the two screws H on the rear panel on the backof the body.Fig.17Fig.18Tuner pack(C

47、N1)AUX & surround boardRear panelHRear panel1-12 (No.MB207)3.1.8Removing the AUX & surround board(See Fig.19, 20) Prior to performing the following procedure, remove the metalcover and the CD changer unit.(1) Disconnect the card wire from the connector CN411,CN711 on the on the AUX & surround board

48、on the rightside of the body. (2) Remove the screw J on the rear panel on the back of thebody.Fig.19Fig.20Tuner packAUX & surroud board(CN411)Rear panelJRear panel(No.MB207)1-133.1.9Removing the rear panel(See Fig.2125) Prior to performing the following procedure, remove the metalcover and the CD ch

49、anger unit.(1) Disconnect the wire from the connector CN1 on the tunerpack assembly on the right side of the body.(2) Disconnect the wire from the connector CN411, CN711 onthe AUX surround board.(3) Remove the screw K attaching the rear cover on the backof the body.(4) Remove the two screws L attach

50、ing the speaker board,and the two screws M attaching the power transformerboard on the back of the body.(5) Remove the four screws N attaching the heat sink on theback of the body.(6) Remove the screw P attaching the rear cover on the backof the body.(7) Release the two joints f and g on the bottom