JVC-UXA52R-cs-sm 维修电路原理图.pdf

《JVC-UXA52R-cs-sm 维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《JVC-UXA52R-cs-sm 维修电路原理图.pdf（127页珍藏版）》请在收音机爱好者资料库上搜索。

1、1-1UX-A52RSERVICE MANUALMICRO COMPONENET SYSTEMNo.21064Feb. 2002COPYRIGHT 2002 VICTOR COMPANY OF JAPAN, LTD.UX-A52RUX-A52RArea Suffix Safety precautionsPreventing static electricityImportant for laser productsDisassembly methodAdjustment Method ContentsFlow of functional operation until TOC read (CD

2、)Maintenance of laser pickupReplacement of laser pickup Description of major ICs1-21-41-51-61-251-291-301-301-3149B - U.K.E - Continental EuropeEN - Northem EuropeSTANDBY/ONCOMPACTDIGITAL AUDIOMICRO COMPONENT SYSTEM UX-A52RPHONESCOLORCLOCK/TIMERFM MODEDISPLAYSOUNDMODE AHBPROSETCANCELCDDIMMER123FM/AM

3、REPEATTAPESTANDBY/ONSLEEP PLAY MODEBEEPVOLUME456789100+10RM-SUXA52RREV.MODEAUX/MDSELECT+- RDS -CONTROLPTYDISPLAYTA/NEWS /INFORadioFans.CN 收音机爱 好者资料库1-2UX-A52R1. This design of this product contains special hardware and many circuits and components specially for safety purposes. For continued protect

4、ion, no changes should be made to the original design unless authorized in writing by the manufacturer. Replacement parts must be identical to those used in the original circuits. Services should be performed by qualified personnel only.2. Alterations of the design or circuitry of the product should

5、 not be made. Any design alterations of the product should not be made. Any design alterations or additions will void the manufacturers warranty and will further relieve the manufacture of responsibility for personal injury or property damage resulting therefrom.3. Many electrical and mechanical par

6、ts in the products have special safety-related characteristics. These characteristics are often not evident from visual inspection nor can the protection afforded by them necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have thes

7、e special safety characteristics are identified in the Parts List of Service Manual. Electrical components having such features are identified by shading on the schematics and by ( ) on the Parts List in the Service Manual. The use of a substitute replacement which does not have the same safety char

8、acteristics as the recommended replacement parts shown in the Parts List of Service Manual may create shock, fire, or other hazards.4. The leads in the products are routed and dressed with ties, clamps, tubings, barriers and the like to be separated from live parts, high temperature parts, moving pa

9、rts and/or sharp edges for the prevention of electric shock and fire hazard. When service is required, the original lead routing and dress should be observed, and it should be confirmed that they have been returned to normal, after re-assembling.5. Leakage currnet check (Electrical shock hazard test

10、ing)After re-assembling the product, always perform an isolation check on the exposed metal parts of the product (antenna terminals, knobs, metal cabinet, screw heads, headphone jack, control shafts, etc.) to be sure the product is safe to operate without danger of electrical shock.Do not use a line

11、 isolation transformer during this check.Plug the AC line cord directly into the AC outlet. Using a Leakage Current Tester, measure the leakage current from each exposed metal parts of the cabinet, particularly any exposed metal part having a return path to the chassis, to a known good earth ground.

12、 Any leakage current must not exceed 0.5mA AC (r.m.s.).Alternate check methodPlug the AC line cord directly into the AC outlet. Use an AC voltmeter having, 1,000 ohms per volt or more sensitivity in the following manner. Connect a 1,500 10W resistor paralleled by a 0.15 F AC-type capacitor between a

13、n exposed metal part and a known good earth ground.Measure the AC voltage across the resistor with the AC voltmeter. Move the resistor connection to each exposed metal part, particularly any exposed metal part having a return path to the chassis, and meausre the AC voltage across the resistor. Now,

14、reverse the plug in the AC outlet and repeat each measurement. Voltage measured any must not exceed 0.75 V AC (r.m.s.). This corresponds to 0.5 mA AC (r.m.s.). 1. This equipment has been designed and manufactured to meet international safety standards.2. It is the legal responsibility of the repaire

15、r to ensure that these safety standards are maintained.3. Repairs must be made in accordance with the relevant safety standards.4. It is essential that safety critical components are replaced by approved parts.5. If mains voltage selector is provided, check setting for local voltage.Good earth groun

16、dPlace this probe on each exposedmetal part.AC VOLTMETER(Having 1000 ohms/volts,or more sensitivity)1500 10W0.15 F AC TYPE!Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system.In regard with

17、component parts appearing on the silk-screen printed side (parts side) of the PWB diagrams, the parts that are printed over with black such as the resistor ( ), diode ( ) and ICP ( ) or identified by the mark nearby are critical for safety. (This regulation does not correspond to J and C version.)Ra

18、dioFans.CN 收音机爱 好者资料库1-3UX-A52R1. Service should be performed by qualified personnel only.2. This equipment has been designed and manufactured to meet international safety standards.3. It is the legal responsibility of the repairer to ensure that these safety standards are maintained.4. Repairs must

19、 be made in accordance with the relevant safety standards.5. It is essential that safety critical components are replaced by approved parts.6. If mains voltage selector is provided, check setting for local voltage.1. This design of this product contains special hardware and many circuits and compone

20、nts specially for safety purposes. For continued protection, no changes should be made to the original design unless authorized in writing by the manufacturer. Replacement parts must be identical to those used in the original circuits. 2. Any unauthorised design alterations or additions will void th

21、e manufacturers guarantee ; furthermore the manufacturer cannot accept responsibility for personal injury or property damage resulting therefrom.3. Essential safety critical components are identified by ( ) on the Parts List and by shading on the schematics, and must never be replaced by parts other

22、 than those listed in the manual. Please note however that many electrical and mechanical parts in the product have special safety related characteristics. These characteristics are often not evident from visual inspection. Parts other than specified by the manufacturer may not have the same safety

23、characteristics as the recommended replacement parts shown in the Parts List of the Service Manual and may create shock, fire, or other hazards.4. The leads in the products are routed and dressed with ties, clamps, tubings, barriers and the like to be separated from live parts, high temperature part

24、s, moving parts and/or sharp edges for the prevention of electric shock and fire hazard. When service is required, the original lead routing and dress should be observed, and it should be confirmed that they have been returned to normal, after re-assembling.!Burrs formed during molding may be left o

25、ver on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system.(U.K only)1-4UX-A52RPreventing static electricity1.Grounding to prevent damage by static electricityElectrostatic discharge (ESD), which occurs when static electricity stored in t

26、he body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.2.About the earth processing for the destruction prevention by static electricity Static electricity in the work area can destroy the optical pick

27、up (laser diode) in devices such as CD players. Be careful to use proper grounding in the area where repairs are being performed. 2-1 Ground the workbench Ground the workbench by laying conductive material (such as a conductive sheet) or an iron plate over it before placing the traverse unit (optica

28、l pickup) on it.2-2 Ground yourself Use an anti-static wrist strap to release any static electricity built up in your body. 3. Handling the optical pickup1. In order to maintain quality during transport and before installation, both sides of the laser diode on the replacement optical pickup are shor

29、ted. After replacement, return the shorted parts to their original condition. (Refer to the text.)2. Do not use a tester to check the condition of the laser diode in the optical pickup. The testers internal power source can easily destroy the laser diode. 4.Handling the traverse unit (optical pickup

30、)1. Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit. 2. Cut off the shorted part of the flexible cable using nippers, etc. after replacing the optical pickup. For specific details, refer to the replacement procedure in the text. Remove the anti-

31、static pin when replacing the traverse unit. Be careful not to take too long a time when attaching it to the connector. 3. Handle the flexible cable carefully as it may break when subjected to strong force. 4. It is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not

32、turn itAttention when traverse unit is decomposed1.Solder is put up before the card wire is removed from connector on the CD substrate as shown in Figure. (When the wire is removed without putting up solder, the CD pick-up assembly might destroy.)2.Please remove solder after connecting the card wire

33、 with when you install picking up in the substrate.*Please refer to Disassembly method in the text for pick-up and how to detach the substrate. (caption)Anti-static wrist strapConductive material (conductive sheet) or iron plateCN601 onmechanismboardShorting roundShorting roundFlexible wire1-5UX-A52

34、RImportant for laser products1.CLASS 1 LASER PRODUCT2.DANGER : Invisible laser radiation when open and inter lock failed or defeated. Avoid direct exposure to beam.3.CAUTION : There are no serviceable parts inside theLaser Unit. Do not disassemble the Laser Unit. Replace the complete Laser Unit if i

35、t malfunctions.4.CAUTION : The compact disc player uses invisible laserradiation and is equipped with safety switches whichprevent emission of radiation when the drawer is open and the safety interlocks have failed or are de feated. It is dangerous to defeat the safety switches.5.CAUTION : If safety

36、 switches malfunction, the laser is able to function.6.CAUTION : Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.VARNING : Osynlig laserstrlning r denna del r ppnad och sprren r urkopplad. Betrakta ej strlen.VARO

37、: Avattaessa ja suojalukitus ohitettaessa olet alttiina nkymttmlle lasersteilylle.l katso steeseen.ADVARSEL : Usynlig laserstrling ved bning , nr sikkerhedsafbrydere er ude af funktion. Undg udsttelse for strling.ADVARSEL : Usynlig laserstrling ved pning,nr sikkerhetsbryteren er avslott. unng utsett

38、else for strling.REPRODUCTION AND POSITION OF LABELSWARNING LABELCLASS 1LASER PRODUCT!CAUTIONPlease use enough caution not to see the beam directly or touch it in case of an adjustment or operationcheck.1-6UX-A52RRemove the eight screws A on the back of the body.Remove the two screws B on the bottom

39、 of the body.Unlock the speaker terminal and the antenna terminal, then remove the rear cover backward with releasing the hooks.1.2.3.Disassembly methodRemoving the rear cover (See Fig.1 and 2)Prior to performing the following procedure, remove the rear cover.Remove the two screws C attaching the si

40、de panels on the bottom of the body.Remove each side panel backward while releasing the eight joints a as shown in Fig.4 and 5.1.2.Removing the side panels (See Fig.3 to 5)(Bottom)Fig.1 AAAAAntenna terminalRear coverSpeaker terminalFig.2Fig.3Fig.4Fig.5Side panel (R)Side panel (L)Side panel (L)Rear c

41、overBBSide panel (R)Side panel (R)Side panel (L)CCJoint aJoint aJoint aJoint a(Bottom)1-7UX-A52RPrior to performing the following procedure, remove the rear cover and the side panels.Remove the two screws D on each side of the body.Release the two joints b on each side of the body and remove the top

42、 panel in the direction of the arrow.Disconnect the card wires from connector CN705 on the system control board on the left side of the body.1.2. 3.Removing the top panel (See Fig.6 and 7) Prior to performing the following procedure, remove the rear cover, the side panels and the top panel.Disconnec

43、t each wire from connector CN706, CN715 and CN716 on the system control board on top of the body.Remove the four screws E retaining the cassette mechanism assembly section on top of the body.1.2.Removing the cassette mechanism assembly section (See Fig.8)Reference: If necessary, remove the spacer ma

44、rked h and the wire from the Cassette mechanism assembly section.REFERENCE: Fig.7Fig.8Fig.6Top panelTop panelDCN705DSystem control boardCN715System control boardCN706EEJoint bJoint bCN716Eh (spacer)Cassette mechanism section1-8UX-A52RPrior to performing the following procedure, remove the rear cover

45、 and the right side panel.Disconnect the card wire from connector CN1 on the tuner board on the right side of the body.Remove the screw G and remove the tuner board upward while disengaging the three joints c.1.2.Removing the tuner board (See Fig.10)Prior to performing the following procedure, remov

46、e the rear cover, the side panels and the top panel.Disconnect the card wire from connector CN701 and the wire from connector CN706, CN715, CN716 on the system control board. Remove the screw F on the left side of the body.Disconnect connector CN709, CN711 and CN712 on the system control board from

47、the body outward.Disconnect the card wire from connector CN704 on the underside of the system control board.1.2.3.4.Removing the system control board(See Fig.9)Fig.9Fig.10System control boardFCN712CN711CN701CN709CN704CN1GJoints cTuner boardCN715CN716CN7061-9UX-A52RPrior to performing the following p

48、rocedure, remove the rear cover, the side panels, the top panel and the system control board.Release the two joints d on the lower right and left sides of the front panel assembly, then remove the front panel assembly toward the front.1.Removing the front panel assembly (See Fig.11 and 12)Prior to p

49、erforming the following procedure, remove the rear cover, the side panels, the top panel, the system control board and the front panel assembly section.Disconnect the wire from connector CN804 on the main board.Remove the plastic rivet fixing the headphone jack board.1.2.Removing the headphone jack

50、board(See Fig.13 and 14)Fig.11Fig.12Fig.13Fig.14Front panel assemblyFront panel assemblyJoint dJoint dHeadphone jack boardHeadphone jack boardMain boardCN804Plastic rivet1-10UX-A52RPrior to performing the following procedure, remove the rear cover, the side panels, the top panel, the cassette mechan