Sony-STRDA2100ES-rec-sm 维修电路原理图.pdf

《Sony-STRDA2100ES-rec-sm 维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Sony-STRDA2100ES-rec-sm 维修电路原理图.pdf（94页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUALAUDIO POWER SPECIFICATIONSPOWER OUTPUT AND TOTAL HARMONIC DISTORTION:(Models of area code U only)With 8 ohm loads, both channels driven, from 20 20,000 Hz; rated 110 watts per channel minimum RMS power, with no more than 0 09% total harmonic distortion from 250 milliwatts to rated outp

2、utAmplifier sectionPower outputModels of area code U, CARated Power Output at Stereo Mode(8 ohms 20 Hz 20 kHz, THD 0 09%)110 W + 110 W1)(8 ohms 1 kHz, THD 0 7%)120 W + 120 W1)(8 ohms 1 kHz, THD 10%)150 W + 150 W1)Reference Power Output1)(8 ohms 20 Hz 20 kHz, THD 0 09%)FRONT2): 110 W/chCENTER2): 110

3、WSURR2): 110 W/chSURR BACK2): 110 W/ch(8 ohms 1 kHz, THD 0 7%)FRONT2): 120 W/chCENTER2): 120 WSURR2): 120 W/chSURR BACK2): 120 W/ch(8 ohms 1 kHz, THD 10%)FRONT2): 150 W/chCENTER2): 150 WSURR2): 150 W/chSURR BACK2): 150 W/ch1) Measured under the following conditions120 V AC, 60 Hz2) Depending on the

4、sound field settings and the source, there may be no sound outputFrequency responseInputs (Analog)3) INPUT SHORT (with sound field and equalizerbypassed)4) Weighted network, input levelInputs (Digital)Outputs (Analog)Outputs (Digital)EqualizerPHONORIAA equalization curve 0 5 dBMULTI CH IN, SA-CD/CD,

5、 TV/SAT, MD/TAPE, DVD, VIDEO 1, 2, 310 Hz 100 kHz+0 5/2 dB (with sound field and equalizer bypassed)PHONOSensitivity: 8 mVImpedance: 50 kiloohmsS/N3): 86 dB(A, 8 mV4)MULTI CH IN, SA-CD/CD, TV/SAT, MD/TAPE, DVD, VIDEO 1, 2, 3Sensitivity: 500 mVImpedance: 50 kiloohmsS/N3): 96 dB(A, 500 mV4)DVD, SA-CD/

6、CD(Coaxial)Sensitivity: Impedance: 75 ohmsS/N: 100 dB(A, 20 kHz LPF)TV/SAT, SA-CD/CD,MD/TAPE, VIDEO 3(Optical)Sensitivity: Impedance: S/N: 100 dB(A, 20 kHz LPF)MD/TAPE (OUT),VIDEO 1, 2(AUDIO OUT)Voltage: 500 mVImpedance: 10 kiloohmsSUB WOOFERVoltage: 2 VImpedance: 1 kiloohmsMD/TAPE (Optical)Sensitiv

7、ity: Gain levels10 dB, 0 5 dB stepFM STEREO FM/AM RECEIVERUS ModelCanadian ModelSTR-DA2100ESVer. 1.2 2006.02SPECIFICATIONS9-879-631-032006B05-1 2006.02Sony CorporationHome Audio DivisionPublished by Sony Techno Create Corporation Continued on next page This receiver incorporates Dolby* Digital and P

8、ro Logic Surround and theDTS* Digital Surround System.* Manufactured under license from Dolby Laboratories.“Dolby”, “Pro Logic” and the double-D symbol are trademarks ofDolby Laboratories.*“DTS”, “DTS-ES”, “Neo:6” and “DTS 96/24” are trademarks ofDigital Theater Systems, Inc.RadioFans.CN 收音机爱 好者资料库2

9、STR-DA2100ESFM tuner sectionTuning range87 5 - 108 0 MHzAntennaFM wire antennaAntenna terminals75 ohms, unbalancedIntermediate frequency10 7 MHzSensitivityMono:18 3 dBf, 2 2 V/75 ohmsStereo:38 3 dBf, 22 5 V/75 ohms Useable sensitivity11 2 dBf, 1 V/75 ohmsS/NMono: 76 dBStereo: 70 dBHarmonic distortio

10、n at 1 kHzMono: 0 3%Stereo: 0 5%Separation45 dB at 1 kHzFrequency response30 Hz 15 kHz, +0 5/2 dBSelectivity60 dB at 400 kHzAM tuner sectionTuning rangeWith 10-kHz tuning scale: 530 1,710 kHz5)With 9-kHz tuning scale: 531 1,710 kHz5)AntennaLoop antennaIntermediate frequency450 kHzUsable sensitivity5

11、0 dB/m (at 1,000 kHz or 999 kHz)S/N54 dB (at 50 mV/m)Harmonic distortion0 5% (50 mV/m, 400 Hz)SelectivityAt 9 kHz:35 dBAt 10 kHz:40 dB5) You can change the AM tuning scale to 9 kHz or 10 kHz After tuning in any AM station, turn off the receiver While holding down PRESET TUNING + or TUNING +, press ?

12、/1 All preset stations will be erased when you change the tuning scale To reset the scale to 10 kHz (or 9 kHz), repeat the procedureVideo sectionInputs/OutputsVideo:1 Vp-p, 75 ohmsS-video:Y: 1 Vp-p, 75 ohmsC: 0 286 Vp-p, 75 ohmsCOMPONENT VIDEO:Y: 1 Vp-p, 75 ohmsPB/CB/B-Y: 0 7 Vp-p, 75 ohmsPR/CR/R-Y:

13、 0 7 Vp-p, 75 ohms80 MHz HD Pass ThroughGeneralPower requirements120 V AC, 60 HzPower consumptionPower consumption (during standby mode)0 5 W (when “INST MODE” in the CIS menu is set to “OFF”)AC outlets2 switched, 120 W/1A MAXDimensions (w/h/d) (Approx )430 160 5 398 5 mm (16 7/8 6 2/8 15 5/8 inches

14、) including projecting parts and controlsMass (Approx )14 0 kg (30 lb 14 oz)Supplied accessoriesFM wire antenna (1)AM loop antenna (1)Remote commander RM-AAE001 (1) R6 (size-AA) batteries (2) Design and specifications are subject to change without noticeArea codePower consumptionU310 WCA420 VARadioF

15、ans.CN 收音机爱 好者资料库3STR-DA2100ESNotes on chip component replacement Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor may bedamaged by heat.ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT!LES COMPOSANTS IDENTIFIS PAR UNE MARQUE 0 SURLES DIAGRAMMES SCHMATIQUES

16、 ET LA LISTE DESPICES SONT CRITIQUES POUR LA SCURIT DEFONCTIONNEMENT. NE REMPLACER CES COM- POSANTSQUE PAR DES PICES SONY DONT LES NUMROS SONTDONNS DANS CE MANUEL OU DANS LES SUPPLMENTSPUBLIS PAR SONY.SAFETY-RELATED COMPONENT WARNING!COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINEWITH MARK 0 ON THE S

17、CHEMATIC DIAGRAMS AND INTHE PARTS LIST ARE CRITICAL TO SAFE OPERATION.REPLACE THESE COMPONENTS WITH SONY PARTS WHOSEPART NUMBERS APPEAR AS SHOWN IN THIS MANUAL ORIN SUPPLEMENTS PUBLISHED BY SONY.SAFETY CHECK-OUTAfter correcting the original service problem, perform the followingsafety check before r

18、eleasing the set to the customer:Check the antenna terminals, metal trim, “metallized” knobs, screws,and all other exposed metal parts for AC leakage.Check leakage as described below.LEAKAGE TESTThe AC leakage from any exposed metal part to earth ground andfrom all exposed metal parts to any exposed

19、 metal part having areturn to chassis, must not exceed 0.5 mA (500 microamperes.).Leakage current can be measured by any one of three methods.1. A commercial leakage tester, such as the Simpson 229 or RCAWT-540A. Follow the manufacturers instructions to use theseinstruments.2. A battery-operated AC

20、milliammeter. The Data Precision 245digital multimeter is suitable for this job.3. Measuring the voltage drop across a resistor by means of aVOM or battery-operated AC voltmeter. The “limit” indicationis 0.75 V, so analog meters must have an accurate low-voltagescale. The Simpson 250 and Sanwa SH-63

21、Trd are examplesof a passive VOM that is suitable. Nearly all battery operateddigital multimeters that have a 2 V AC range are suitable. (SeeFig. A)Fig. A.Using an AC voltmeter to check AC leakage.1.5 k0.15 FACvoltmeter(0.75 V)To Exposed MetalParts on SetEarth Ground4STR-DA2100ESTABLE OF CONTENTS1.S

22、ERVICING NOTES.52.GENERAL.63.DISASSEMBLY3-1.Disassembly Flow .73-2.Case .73-3.Front Panel Block .83-4.Back Panel Block .83-5.DIGITAL Board .93-6.MAIN Board.94.TEST MODE. 105.ELECTRICAL ADJUSTMENTS. 116.DIAGRAMS6-1.Block Diagram DIGITAL AUDIO Section (1/2) . 126-2.Block Diagram DIGITAL AUDIO Section

23、(2/2) . 136-3.Block Diagram ANALOG AUDIO Section . 146-4.Block Diagram POWER AMP Section . 156-5.Block Diagram VIDEO INPUT Section . 166-6.Block Diagram CIS, DISPLAY Section . 176-7.Block Diagram POWER SUPPLY Section . 186-8.Printed Wiring Board VIDEO (AU) Board . 206-9.Schematic Diagram VIDEO (AU)

24、Board . 216-10. Printed Wiring Board DIGITAL Board (Component Side) . 226-11. Printed Wiring Board DIGITAL Board (Conductor Side) . 236-12. Schematic Diagram DIGITAL Board (1/5) . 246-13. Schematic Diagram DIGITAL Board (2/5) . 256-14. Schematic Diagram DIGITAL Board (3/5) . 266-15. Schematic Diagra

25、m DIGITAL Board (4/5) . 276-16. Schematic Diagram DIGITAL Board (5/5) . 286-17. Printed Wiring Board A/V SYNC Board . 306-18. Schematic Diagram A/V SYNC Board . 316-19. Printed Wiring Board MAIN Board . 326-20. Schematic Diagram MAIN Board (1/3) . 336-21. Schematic Diagram MAIN Board (2/3) . 346-22.

26、 Schematic Diagram MAIN Board (3/3) . 356-23. Printed Wiring Boards SPEAKER Section . 366-24. Schematic Diagram SPEAKER Section . 376-25. Printed Wiring Board VIDEO Board (Component Side) . 386-26. Printed Wiring Board VIDEO Board (Conductor Side) . 396-27. Schematic Diagram VIDEO Board (1/2) . 406-

27、28. Schematic Diagram VIDEO Board (2/2) . 416-29. Printed Wiring Board SVIDEO Board . 426-30. Schematic Diagram SVIDEO Board . 436-31. Printed Wiring Boards DISPLAY Section . 446-32. Schematic Diagram DISPLAY Section . 456-33. Printed Wiring Boards CIS Section . 466-34. Schematic Diagram CIS Section

28、 . 476-35. Printed Wiring Board STANDBY Board . 486-36. Schematic Diagram STANDBY Board . 497.EXPLODED VIEWS7-1.Overall Section . 687-2.Front Panel Section . 697-3.Base Panel Section . 707-4.Power Transformer Section . 717-5.Chassis Section. 727-6.Back Panel Section . 737-7.MAIN Board Section. 748.E

29、LECTRICAL PARTS LIST. 755STR-DA2100ESPART No. Back Panel SECTION 1SERVICING NOTES MODEL IDENTIFICATIONModelPART No.US model2-514-880-0Canadian model2-514-880-1UNLEADED SOLDERBoards requiring use of unleaded solder are printed with the lead-free mark (LF) indicating the solder contains no lead.(Cauti

30、on: Some printed circuit boards may not come printed withthe lead free mark due to their particular size): LEAD FREE MARKUnleaded solder has the following characteristics. Unleaded solder melts at a temperature about 40 C higherthan ordinary solder.Ordinary soldering irons can be used but the iron t

31、ip has to beapplied to the solder joint for a slightly longer time.Soldering irons using a temperature regulator should be set toabout 350 C.Caution: The printed pattern (copper foil) may peel away ifthe heated tip is applied for too long, so be careful! Strong viscosityUnleaded solder is more visco

32、u-s (sticky, less prone to flow)than ordinary solder so use caution not to let solder bridgesoccur such as on IC pins, etc. Usable with ordinary solderIt is best to use only unleaded solder but unleaded solder mayalso be added to ordinary solder.6STR-DA2100ESSECTION 2GENERALThis section is extracted

33、 frominstruction manual.Main unitA F D qgDIRECT q;DISPLAY 7Display 5INPUT MODE 8INPUT SELECTOR qsIR (receptor) 1MASTER VOLUME /+ 9MEMORY/ENTER 4MENU wfMOVIE qfMULTI CHANNEL DECODING (indicator) 6MULTI CH IN qaMUSIC qdSPEAKERS (OFF/A/B/A+B) whSURR BACK DECODING qjTUNING + qkTUNING qlVIDEO 3 INPUT (ja

34、cks) wd2CH qh?/1 (power) 2/+ wsALPHABETICAL ORDERA - IMAIN MENU 3M - OPHONES (jack) wgPRESET TUNING + w;PRESET TUNING waP - ZNUMBERS AND SYMBOLSwdwgwhwf289653471qlwswa w;qk qj qh qg qf qdqsqaq;STR-DA2100ES7Note: Follow the disassembly procedure in the numerical order given.3-2.CASE This set can be d

35、isassembled in the order shown below.3-1.DISASSEMBLY FLOWSECTION 3DISASSEMBLY3-2. CASE(Page 7)3-3. FRONT PANEL BLOCK(Page 8)3-4. BACK PANEL BLOCK(Page 8)3-5. DIGITAL BOARD(Page 9)3-6. MAIN BOARD(Page 9)SET1two flat head screws(TP)2two flat head screws(TP)3two flat head screws(TP)4two flat head screw

36、s(TP)5caseSTR-DA2100ES83-3.FRONT PANEL BLOCK3-4.BACK PANEL BLOCK7front panel block6two connectors(CN1081, 1091)4two screws(BVTP3 8)2wire (flat type)(29 core)1connector(CNS505)3six screws(BVTP3 8)52connector(CN1071)1wire (flat type)(11 core: CNP210)1wire (flat type)(5 core: CNS204)2connector(CNP207)2

37、connector(CNP851)6two screws(BVTP4 8)3eleven screws(BVTP3 8)4ten screws(BVTP3 8)5three screws(BVTP3 8)9back panel section8two connectors(CNP208, 801)1wire (flat type) (11 core)7STR-DA2100ES93-5.DIGITAL BOARD3-6.MAIN BOARD1wire (flat type) (29 core)(CNS505)2two connectors(CNP507, CNP510)7A/V SYNC boa

38、rd2connector(CNP506)8DIGITAL board5connector(CNS551)3two connectors(CNP811, CNP814)4screw (BVTP3 8)6AV SYNC holder1connector(CNP813)4three screws(BVTP3 8)2screw(BVTP3 8)1two connectors(CN908, CNP802)5two screws(BVTP3 8)6MAIN board3guide boards section10STR-DA2100ESSECTION 4TEST MODESOUND FIELD INITI

39、ALIZE MODEThe preset sound field is cleared when this mode is activated. Usethis mode before returning the product to clients upon completionof repair.Procedure:1. While pressing the 2CH button, press theI/1button to turnon the main power.2. The message “S. F. INITIALIZE” appears and initializationi

40、s performed.COMMAND MODE CHANGE MODEThe command mode of the remote-commander which this setreceives can be changed.Procedure:1. While pressing the INPUT MODE button, press theI/1buttonto turn on the main power.2. Either the message “C.MODE.AV1” or “C.MODE.AV2”appears. Select the desired mode.SF LOCK

41、 ON/OFF CHANGE MODEProcedure:1. While pressing the MUSIC and MEMORY/ENTER buttons,press theI/1button to turn on the main power.2. Either the message “SF LOCK OFF” or “SF LOCK ON”appears.TUNER FACTORY PRESET MODEAll preset contents are reset to the default setting.Procedure:1. While pressing the MULT

42、I CH IN and DISPLAY buttons, presstheI/1button to turn on the main power.2. The message “FACTORY PRESET” appears and the presentcontents are reset to the default values.MEMORY CLEARING MODEAll preset contents are cleared when this mode is activated. Usethis mode before returning the product to clien

43、ts upon completionof repair.Procedure:1. While pressing the MUSIC and SPEAKERS buttons, presstheI/1button to turn on the main power.2. The message “MEMORY CLEARING” appears and thememories are reset to the default values.3. When done, the message “MEMORY CLEARED” appears.VERSION MODEWhen this mode i

44、s used, the model, the destination and the softwareversion number are displayed.Procedure:1. While pressing the DISPLAY and TUNING - buttons, presstheI/1button to turn on the main power.2. The model, the destination and the software version numberappears.SWAP MODEProcedure:1. While pressing the MAIN

45、 MENU and PRESET TUNING -buttons, press theI/1button to turn on the main power.2. The message “SWAP MODE ” appears.3. Press the MEMORY/ENTER button.4. The message “00dB” appears. (Volume level is “MIN”)5. Press the MEMORY/ENTER button once again.6. The message “49dB” appears. (Volume level is “MID”)

46、7. Press the MEMORY/ENTER button once again.8. The message “+13dB” appears. (Volume level is “MAX”)9. Press the MEMORY/ENTER button once again.10. The message “MUTING” appears.11. Press the MEMORY/ENTER button once again.12. The message “MUTING OFF” appears.FLUORESCENT INDICATOR TUBE PATTERNCHECK MO

47、DEAll fluorescent segments are tested. When this test is activated, allsegments turn on at the same time, then each segment turns on oneafter another.Procedure:1. While pressing the SPEAKER and TUNING - buttons, presstheI/1button to turn on the main power.2. All segments and MULTI CHANNEL DECODING i

48、ndicatorLED turn on.TUNER AM STEP CHANGE (9 kHz/10 kHz) MODEEither the 9 kHz step or 10 kHz step can be selected for the AMchannel step.Procedure:1. Press theI/1button to turn on the main power.2. Turn the INPUT SELECTOR dial to select the “AM”3. Press theI/1button to turn off the main power.4. Whil

49、e pressing the PRESET TUNING + or TUNING + button,press theI/1button to turn on the main power.5. Either the message “9 K STEP” or “10 K STEP” appears.Select the desired step.1111STR-DA2100ESSTR-DA2100ESSECTION 5ELECTRICAL ADJUSTMENTSOSD ADJUSTMENTConnectionProcedure:1. Short the CNP3501 pin 4 on th

50、e VIDEO board to the GND.2. Connect a frequency counter to the CNP3501 pin 2 on theVIDEO board.3. Press the I/1 button to turn on the main power.4. Press the MAIN MENU button to display “CUSTOMIZE ”.5. Turn the MENU jog clockwise to display “OSD COLORNTSC”. If “OSD COLOR PAL” is displayed, turn the