Sony-STRDE135-rec-sm 维修电路原理图.pdf

《Sony-STRDE135-rec-sm 维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Sony-STRDE135-rec-sm 维修电路原理图.pdf（30页珍藏版）》请在收音机爱好者资料库上搜索。

1、MICROFILMSERVICE MANUALFM STEREO/FM-AM-RECEIVERUS ModelAEP ModelUK ModelSTR-DE135SPECIFICATIONSPhoto: US modelAudio power specifications (US model)POWER OUTPUT AND TOTAL HARMONIC DISTORTIONWith 8-ohm load, both channels driven, from 20 20,000 Hz,rated 100 watts per channel minimum RMS power, with no

2、more than 0.09 % total harmonic distortion from 250 milli-watts to rated output.Amplifier sectionStereo mode(8 ohms at 20 Hz 20 kHz less than0.09 % total harmonic distortion)100 W + 100 W (US model)(DIN 1 kHz, 4 ohms)60 W + 60 W (AEP, UK models)Frequency responseTV/SAT, CD, MD/TAPE, VIDEO(US model)T

3、V/LD, CD, MD/TAPE, VIDEO(AEP, UK models)10 Hz 50 Hz 1 dBInputsSensitivityImpedanceS/NCD,MD/TAPE,150 mV5078 dBTV/SAT,kilohmsVIDEO(US model)SensitivityImpedanceS/NCD,MD/TAPE,150 mV5078 dBTV/LD,kilohmsVIDEO(AEP, UK models)outputsMD/TAPE REC OUT:Voltage: 150 mV, impedance: 10 kilohmsVIDEO AUDIO OUT:Volt

4、age: 150 mV, impedance: 10 kilohmsPHONES: Accepts low and highimpedance headphonesMutingFull muteBASS BOOST+ 10 dB at 70 HzTONE 8 dB at 100 Hz and 10 kHzTuner SectionFM stereo, FM/AM superheterodyne tunerFM tuner sectionTuning range87.5 108.0 MHzAntenna terminals75 ohms, unbalancedIntermediate frequ

5、ency10.7 MHzSensitivityMono: 18.3 dBf, 4.5 VStereo: 38.3 dBf, 45 V (US model)Mono: 18.3 dBf, 2.2 V/75 ohmsStereo: 38.3 dBf, 22.5 V/75 ohms(AEP, UK models)Usable sensitivity11.2 dBf, 2 V (IHF) (US model)11.2 dBf, 1 V/75 ohms (IHF)(AEP, UK models)S/NMono: 76 dBStereo: 70 dBHarmonic distortion at 1 kHz

6、Mono: 0.3 %Stereo: 0.5 %Separation45 dB at 1kHzFrequency response30 Hz 15 kHz dBSelectivity60 dB at 400 kHzAM tuner sectionTuning range10 kHz interval*530 1710 kHz9 kHz interval531 1710 kHz (US model)531 1602 kHz (AEP, UK models)+0.52 Continued on next page RadioFans.CN 收音机爱 好者资料库 2 TABLE OF CONTENT

7、S1.SERVICING NOTES.32.GENERAL.43.DISASSEMBLY.54.TEST MODE.75.DIAGRAMS5-1.Note for Printed Wiring Boards andSchematic Diagrams .95-2.Printed Wiring Board MAIN Board . 115-3.Schematic Diagram MAIN Board (1/2) . 135-4.Printed Wiring Boards DISPLAY Board/KEY Board/VOLUME Board/ TONE Board/POWER SWITCH B

8、oard . 155-5.Schematic Diagram PANEL Section . 195-6.Printed Wiring Boards PANEL Section . 235-7.Schematic Diagram MAIN Board (2/2)/SPK SWITCH Board/ SECONDARY Board/PRIMARY Board/ STANDBY TRANS Board . 255-8.IC Pin Function Description . 266.EXPLODED VIEWS. 287.ELECTRICAL PARTS LIST. 31SAFETY-RELAT

9、ED COMPONENT WARNING!COMPONENTS IDENTIFIED BY MARK ! OR DOTTEDLINE WITH MARK ! ON THE SCHEMATIC DIAGRAMSAND IN THE PARTS LIST ARE CRITICAL TO SAFEOPERATION. REPLACE THESE COMPONENTS WITHSONY PARTS WHOSE PART NUMBERS APPEAR ASSHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-LISHED BY SONY.AntennaLoop anten

10、naIntermediate frequency450 kHzUsable sensitivity50 dB/m (at 1,000 kHz)S/N54 dB (at 50 mV/m)Harmonic distortion0.5 % (50 mV/m, 400Hz)SelectivityAt 10 kHz: 40 dBAt 9 kHz: 35 dB (US model)35 dB (AEP, UK models)* You can change the AM tuning interval between 9 kHz and 10kHz.After tuning in any AM stati

11、on, turn off the receiver. Hold down thePRESET TUNING + button and press the 1/u (power) button. All pre-set stations will be erased when you change the interval. To reset theinterval, repeat the procedure.(US model)GeneralSystemTuner section:PLL quartz-locked digitalsynthesizer systemPreamplifier s

12、ection:Low-noise NF type equalizerPower amplifier section:Pure-complementary SEPPPower requirements120 V AC, 60 Hz (US model)230 V AC, 50/60 Hz(AEP, UK models)Power consumption155 W (US model)135 W (AEP, UK models)AC outlets1 switched, total 120 W/1A Max(US, UK models)switch 100 W max (AEP model)Dim

13、ensions430 144 306 mm(17 56/8 124/8 inches)Mass (Approx.)8.1 kg (17 lb 13 oz) (US model)6.7 kg (AEP, UK models)Supplied accessoriesFM wire antenna (1)AM loop antenna (1)Remote commander (remote) (1)Size AA (R6) batteries (2)Specifications indicated are measured at 230 V AC, 50Hz.(AEP, UK models)Desi

14、gn and specifications are subject to change without notice.RadioFans.CN 收音机爱 好者资料库 3 SECTION 1SERVICING NOTESMODEL IDENTIFICATION Rear view 12345PART No.MODELPART No.US model4-216-802-0AEP model4-216-802-1UK model4-216-802-2SAFETY CHECK-OUTAfter correcting the original service problem, perform the f

15、ollow-ing safety check before releasing the set to the customer:Check the antenna terminals, metal trim, “metallized” knobs,screws, and all other exposed metal parts for AC leakage.Check leakage as described below.LEAKAGE TESTThe AC leakage from any exposed metal part to earth ground andfrom all exp

16、osed metal parts to any exposed metal part having areturn to chassis, must not exceed 0.5 mA (500 microampers.).Leakage current can be measured by any one of three methods.1.A commercial leakage tester, such as the Simpson 229 or RCAWT-540A. Follow the manufacturers instructions to use theseinstrume

17、nts.2.A battery-operated AC milliammeter. The Data Precision 245digital multimeter is suitable for this job.3.Measuring the voltage drop across a resistor by means of aVOM or battery-operated AC voltmeter. The “limit” indica-tion is 0.75 V, so analog meters must have an accurate low-voltage scale. T

18、he Simpson 250 and Sanwa SH-63Trd are ex-amples of a passive VOM that is suitable. Nearly all batteryoperated digital multimeters that have a 2 V AC range are suit-able. (See Fig. A)Fig. A.Using an AC voltmeter to check AC leakage.1.5 k0.15 FACvoltmeter(0.75 V)To Exposed MetalParts on SetEarth Groun

19、d 4 SECTION 2GENERAL1 I/u button2 TUNING +, buttons(US model)TUNING/CHAR +, buttons(AEP, UK models)3 NAME button(AEP, UK models)4 PRESET/TUNING +, buttons(US model)PRESET/PTY SELECT +, buttons(AEP, UK models)5 DISPLAY button(AEP, UK models)6 RDS PTY button(AEP, UK models)7 AM button(US model)RDS EON

20、 button(AEP, UK models)Location of controls Front view 8 FM button(US model)FM/AM button(AEP, UK models)9 VIDEO button0 TV/SAT button(US model)TV/LD button(AEP, UK models)! MD/TAPE button! BASS BOOST button and indicator! SPEAKERS A, B ON/OFF buttons! PHONES jack! SHIFT button! Numeric buttons! DIRE

21、CT button! MEMORY button(US model)MEMORY/ENTER button(AEP, UK models)! FM MODE button TUNER button CD button VOLUME control MUTING button and indicator TREBLE control BASS control BALANCE control3451267!8 9 0 ! ! Rear view 5 CASEFRONT PANEL SECTIONNote: Follow the disassembly procedure in the numeri

22、cal order given.SECTION 3DISASSEMBLY1two tapping screws1tapping screw2case 1two tapping screws2three connectors(CNP702 704)3screw(BVTP3 8)4claw5front panelsection3four screws(BVTP3 8)4claw1two flat wires(CNS204, CNP404) 6 REAR PANEL SECTIONMAIN BOARD2connector(CNP901)4rear panel section3four screws(

23、BVTP3 8)3six screws(BVTP3 8)1flat wire(CNS205)2connector(CNS802)2two connectors(CNP703, 704)4PC board holder2connector(CNP801)1two flat wires(CNS204, CNP404)5MAIN board3three screws(BVTP3 8)3three screws(BVTP3 8)2connector(CNP702) 7 SECTION 4TEST MODEFluorescent Indicator Tube Test ModeAll fluoresce

24、nt segments are tested. When this test is activated, allsegments turn on at the same time, then each segment turns on oneafter another.Procedure:1.While pressing two buttons of TV/SAT (US model)* andDIRECT simultaneously, press the 1/u button to turn thepower ON.2.All segments turn on at the same ti

25、me, then each segment turnson one after another.3.The message “FINISH” appears when this test is complete.*) AEP, UK models are TV/LDAUTO-BETICAL Check Mode (AEP, UK models)To auto-scanning and memories of RDS station.Procedure:1.While pressing the MEMORY/ENTER button, press the 1/u button to turn t

26、he power ON.2.The message “AUTO BET” appears and each function is se-lected one after another.AM Tuning Interval Selection Mode (US model)Either 9 kHz step or 10 kHz step can be selected for the AM tun-ing interval.Procedure:1.Set the FUNCTION to AM.2.Press the 1/u button to turn the power OFF.3.Whi

27、le pressing the TUNING+ button, press the 1/u button toturn the power ON.4.Either the message “9k STEP” or “10k STEP” appears.5.Select the desired step.Software Version Display ModeThe software version is displayed.Procedure:1.While pressing two the buttons of MD/TAPE and DIRECTsimultaneously, press

28、 the 1/u button to turn the power ON.2.The software version is displayed. 8 Circuit Boards LocationSECTION 5DIAGRAMSPOWER SWITCH boardPRIMARY boardSECONDARY boardSTANDBY TRANSboardDISPLAY boardVOLUME boardTONE boardKEY boardSPK SWITCHboardMAIN board 9 10 5-1.NOTES FOR PRINTED WIRING BOARDS AND SCHEM

29、ATIC DIAGRAMSNote on Printed Wiring Board: X : parts extracted from the component side. b : Pattern from the side which enables seeing.(The other layers patterns are not indicated.) Indication of transistor.BThese are omitted.CEQ Waveforms MAIN Board 1 IC1 ! (XO)Note on Schematic Diagram: All capaci

30、tors are in F unless otherwise noted. pF: F50 WV or less are not indicated except for electrolyticsand tantalums. All resistors are in and 1/4 W or less unless otherwisespecified.: internal component. 2 : nonflammable resistor. C : panel designation.Note: The components identified by mark ! or dotte

31、d linewith mark ! are critical for safety.Replace only with part number specified. U : B+ Line. V : B Line. Voltages and waveforms are dc with respect to groundunder no-signal (detuned) conditions.no mark : FM Voltages are taken with a VOM (Input impedance 10 M).Voltage variations may be noted due t

32、o normal produc-tion tolerances. Waveforms are taken with a oscilloscope.Voltage variations may be noted due to normal produc-tion tolerances. Circled numbers refer to waveforms. Signal path.F: FM1.6 Vp-p4.33 MHz DISPLAY Board 1 IC201 # (X2)5.4 Vp-p4.19 MHzBThese are omitted.CEQSTR-DE135C757(AEP,UK)

33、C707(AEP,UK) 11 12 5-2.PRINTED WIRING BOARD MAIN Board See page 8 for Circuit Boards Location.D421F-5D710I-11D721H-5D722H-5D723H-6D724I-5D801I-7D802D-12D804I-7D820C-12D821C-12D822C-12D823C-12D951A-10D952A-10D953A-10D954A-10D955A-10D956A-10IC1D-1IC401C-4IC403E-3IC701E-7IC801C-6IC802C-6IC803B-7IC804C-

34、7IC950A-7Q303E-3Q304D-3Q401F-5Q402F-5Q451E-5Q452F-5Q701G-8Q702G-8Q703H-8Q704F-8Q710I-12Q720G-7Q721I-5Q722H-6Q723I-5Q751C-8Q752D-8Q753E-8Q754C-8Q770B-7Q801H-7Q802C-13Q951A-7 SemiconductorLocationRef. No.Location(Page 17)(Page 24)(Page23)(Page 23)(Page 15)(Page23)(Page23)STR-DE1355-3.SCHEMATIC DIAGRAM

35、 MAIN Board (1/2) See page 10 for Waveform. See page 21 for IC Block Diagrams. 13 14 (Page 25)(Page 25)(Page 20)(Page 19)(Page 25)The components identified by mark ! or dottedline with mark ! are critical for safety.Replace only with part number specified.STR-DE135 15 16 5-4.PRINTED WIRING BOARDS PA

36、NEL Section See page 8 for Circuit Boards Location.D201A-3D202A-3D203A-3D204B-3D223A-10D224A-10IC201B-6IC202A-1IC203B-11Q201B-3Q202B-3 SemiconductorLocationRef. No.Location(Page 11)(Page 17)(Page17)STR-DE135 17 18 (Page 18)(Page 11)(Page 15)(Page 16)(Page 17)STR-DE135 19 20 5-5.SCHEMATIC DIAGRAM PAN

37、EL Section See page 10 for Waveform. See page 22 for IC Block Diagram.100k(Page 14)(Page13)The components identified by mark ! or dottedline with mark ! are critical for safety.Replace only with part number specified.STR-DE135 21 22 IC Block Diagrams MAIN Board IC1BU1922 (AEP, UK models)IC401 LC7821

38、2QUALITY BITGENERATORDEFFERENTIALDECODERBIPHASESYMBOLDECODEROSCILLATORANDDIVIDER57kHzBANDPASS(8th ORDER)CONTAS LOOPVARIABLE ANDFIXED DIVIDERREFERENCEVOLTAGEANTI-ALIASINGFILTERCLOCKEDCOMPARATORTEST LOGIC AND OUTPUTSELECTOR SWITCHRECONSTRUCTIONFILTER14151613121110932145678CLOCK REGENERATIONAND SYNCVP1

39、RDCLTS7OSCOOSCIVDDDVSSDTESTTSTLDQUALRDDAVrefMUXVDDAVSSACINSCOUT123456789101112131415302928272625242322212019181716CONTROLLATCHSHIFT RESISTORLEVEL SHIFTCLDICEVEEOUTINOUTINOUTINVSSSRESETVDDOUTININOUTINOUTINIC950 NJM2103D12345678V+VSB/SESINVSARESETGNDOUTCVSCCRVREF+QRSIC701 PC2581V235467981MUTE+ VOUT1 V

40、OUT1COMP1MF1IN1GNDIN2NF2COMP2 VOUT2+ VOUT2VCC1VCC2VEEPROTECTORBIAS CIRCUITREGDRIVEPREDRIVE111012131514DRIVEPREDRIVE DISPLAY Board IC202 BA6208123456789NCOUTPUT 2VccGNDNCINPUT 2INPUT 1NCMOTORDRIVEMOTORDRIVEREGSWITCHSWITCHOUTPUT1STR-DE135 23 24 5-6.PRINTED WIRING BOARDS SPK SWITCH Board/SECONDARY Boar

41、d/PRIMARY Board/STANDBY TRANS Board See page 8 for Circuit Boards Location.(AEP)(Page 12)(Page 24)(Page 12)(Page 12)(Page 12)(Page 12)(Page 23) 25 5-7.SCHEMATIC DIAGRAM MAIN Board (2/2)/SPK SWITCH Board/SECONDARY Board/PRIMARY Board/STANDBY TRANS Board STR-DE135R7421.2k 1/2WR7921.2k 1/2W(Page 14)(Pa

42、ge 14)(Page 14)The components identified by mark ! or dottedline with mark ! are critical for safety.Replace only with part number specified. 26 5-8.IC PIN FUNCTION DESCRIPTION DISPLAY BOARD IC201 PD78044FGF-115-3B9 (SYSTEM CONTROLLER, FL DRIVER)Pin No.Pin NameI/ODescription1 to 7DIG7 to DIG1ODigit

43、drive signal output to the fluorescent indicator tube (FL201)8VDDPower supply terminal (+5V)9S.CLKOSerial data transfer clock signal output to the LC78212 (IC401), PLL IC on FM/AM tuner pack “L” active10S.DATAOSerial data output to the LC78212 (IC401), PLL IC on FM/AM tuner pack “L” active11PLL.DATA

44、ISerial data input from the PLL IC on FM/AM tuner pack “L” active12S.CE (LC7822)OSerial chip enable signal output to the LC78212 (IC401), PLL IC on FM/AM tuner pack“H” active13S.CE (LV1010)OSerial chip enable signal output terminal “L” active Not used (pull down)14REAR-RYORelay drive signal output f

45、or the rear side speaker “H”: relay on Not used (open)15BRIDGEOBridgeable relay drive signal output terminal “H”: relay on Not used (open)16PROTECTIOver load detect signal input from the protect circuit “L”: protect detect17RESETISystem reset signal input from the reset signal generator (IC950, Q201

46、) “L”: resetFor several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”18AUTO-STOPITuned display detection signal input from the FM/AM tuner pack “L”: tuned19STEREO-INIStereo detection signal input from the FM/AM tuner pack “L”: stereo20AVSSGround terminal (for A/D

47、converter analog system)21SP-RYORelay drive signal output for the speaker protect “H”: relay on22SURR-RYORelay drive signal output for the surround speaker “H”: relay on Not used (pull down)23POWER-RYORelay drive signal output for the power on/off control “H”: relay on24SIGNALIFM and AM signal meter

48、 voltage detection signal input from the FM/AM tuner pack25A/D-4IKey input terminal (A/D input) S210 (NAME) key input(Used for the AEP and UK models only)26A/D-3IKey input terminal (A/D input) S231 to S239 (BASS BOOST, MUTING, SHIFT, 0, MEMORY or MEMORY/ENTER, CD, MD/TAPE, TV/SAT or TV/LD, RDS PTY)

49、keys input(S239 RDS PTY key: used for the AEP and UK models only)27A/D-2IKey input terminal (A/D input) S221 to S230 (FM or FM/AM, 6, 5, 4, 7, 8, 9, FM MODE, VIDEO, TUNER) keys input28A/D-1IKey input terminal (A/D input) S211 to S220 (DISPLAY, AM or RDS EON, 3, 2, 1, TUNING or TUNING/CHAR /+, PRESET

50、 TUNING or PRESET/PTY SELECT /+, DIRECT) keys input (S211 DISPLAY key: used for the AEP and UK models only)29AVDDPower supply terminal (+5V) (for A/D converter analog system)30AVREFIReference voltage (+5V) input terminal (for A/D converter)31RDS DATA INIRDS data input from the RDS decoder (IC1) (Use