Sony-STRDA1200ES-rec-sm 维修电路原理图.pdf

《Sony-STRDA1200ES-rec-sm 维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Sony-STRDA1200ES-rec-sm 维修电路原理图.pdf（125页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUALMULTI CHANNEL AV RECEIVERSPECIFICATIONSSTR-DA1200ESVer. 1.1 2006.12 Continued on next page 9-887-344-022006L05-1 2006.12Sony CorporationHome Audio DivisionPublished by Sony Techno Create CorporationAEP ModelUK ModelThis receiver incorporates Dolby* Digital and Pro Logic Surround and th

2、e DTS* Digital Surround System.*Manufactured under license from Dolby Laboratories.“Dolby”, “Pro Logic”, “Surround EX”, and the double-D symbol are trademarks of Dolby Laboratories. * Manufactured under license from DigitalTheater Systems, Inc. U.S. Pat. Nos. 5,451,942; 5,956,674; 5,974,380; 5,978,7

3、62; 6,226,616; 6,487,535 and other U.S. and world-wide patents issued and pending. “DTS”, “DTS-ES”, “Neo:6”, and “DTS 96/24” are trademarks of Digital Theater Systems, Inc. Copyright 1996, 2003 Digital Theater Systems, Inc. All Rights Reserved. Amplifier sectionPOWER OUTPUTRated Power Output at Ster

4、eo Mode1) 2)(8 ohms 1 kHz, THD 0.7%):105 W + 105 WRated Power Output at Stereo Mode2)(4 ohms 1 kHz, THD 0.7%):105 W + 105 WReference Power Output(8 ohms 20 Hz 20 kHz, THD 0.09%)FRONT2): 100 W + 100 WCENTER2): 100 WSURROUND2): 100 W + 100 WSURROUND BACK2): 100 W + 100 WReference Power Output(4 ohms 2

5、0 Hz 20 kHz, THD 0.15%)FRONT2): 100 W + 100 WCENTER2): 100 WSURROUND2): 100 W + 100 WSURROUND BACK2): 100 W + 100 WReference Power Output at Stereo Mode1) 2)(8 ohms 1 kHz, THD 10%):130 W + 130 WReference Power Output at Stereo Mode2)(4 ohms 1 kHz, THD 10%):130 W + 130 WReference Power Output(8 ohms

6、1 kHz, THD 10%)FRONT2): 130 W + 130 WCENTER2): 130 WSURROUND2): 130 W + 130 WSURROUND BACK2): 130 W + 130 WReference Power Output(4 ohms 1 kHz, THD 10%)FRONT2): 130 W + 130 WCENTER2): 130 WSURROUND2): 130 W + 130 WSURROUND BACK2): 130 W + 130 W1)Depending on the sound field settings and the source,

7、there may be no sound output.2)Measured under the following conditions:Power requirements: 230 V AC, 50/60 Hz (in countries/areas in Europe other than the UK)240 V AC, 50/60 Hz (in the UK and general area)Frequency responseInputs (Analog)PHONORIAA equalization curve 0.5 dBMULTI CHANNEL INPUT, SA-CD/

8、CD, MD/TAPE, DVD, VIDEO 1/2/310 Hz 100 kHz 3 dBPHONOSensitivity: 2.5 mVImpedance: 50 kohmsS/N: 86 dB (A, 20 kHz LPF)MULTI CHANNELINPUT, SA-CD/CD, MD/TAPE, DVD, TV/SAT, VIDEO1/2/3Sensitivity: 150 mVImpedance: 50 kohmsS/N: 96 dB (A, 20 kHz LPF)RadioFans.CN 收音机爱 好者资料库2STR-DA1200ESNotes on chip componen

9、t replacement Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor may bedamaged by heat.SAFETY-RELATED COMPONENT WARNING!COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINEWITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND INTHE PARTS LIST ARE CRITICAL TO SAFE OPERATION.R

10、EPLACE THESE COMPONENTS WITH SONY PARTS WHOSEPART NUMBERS APPEAR AS SHOWN IN THIS MANUAL ORIN SUPPLEMENTS PUBLISHED BY SONY.OutputsEQUALIZERFM tuner sectionTuning range87.5 - 108.0 MHzAntenna (aerial)FM wire antenna (aerial)Antenna (aerial) terminals75 ohms, unbalancedSensitivityMono:18.3 dBf, 2.2 V

11、/75 ohmsStereo:38.3 dBf, 22.5 V/75 ohms Usable sensitivity 11.2 dBf, 1 V/75 ohmsS/NMono:76 dBStereo:Harmonic distortion at 1 kHzMono:0.3%Stereo:0.5%Separation45 dB at 1 kHzFrequency response 30 Hz 15 kHz, +0.5/2 dBSelectivity60 dB at 400 kHzAM tuner sectionTuning range531 1,602 kHz(With 9-kHz tuning

12、 scale)Antenna (aerial)Loop antenna (aerial)Usable sensitivity50 dB /m (at 999 kHz)S/N54 dB (at 50 mV/m)Harmonic distortion 0.5% (50 mV/m, 400 Hz)Selectivity35 dBMD/TAPE, VIDEO1/2 (AUDIO OUT)Voltage:150 mVImpedance: 1 kohmsFRONT L/R, CENTER, SURROUND L/R, SURROUND BACK L/R, SUB WOOFERVoltage: 2 VImp

13、edance: 1 kohmsGain levels10 dB, 1 dB stepInputs (Digital)DVD, SA-CD/CD (Coaxial)Impedance: 75 ohmsS/N: 96 dB (A, 20 kHz LPF)VIDEO 1/3, TV/SAT, MD/TAPE (Optical)S/N: 96 dB(A, 20 kHz LPF)Video sectionInputs/OutputsVideo:1 Vp-p, 75 ohmsS video:Y: 1 Vp-p, 75 ohmsC: 0.286 Vp-p, 75 ohmsCOMPONENT VIDEO:Y:

14、 1 Vp-p, 75 ohmsPB/CB: 0.7 Vp-p, 75 ohmsPR/CR: 0.7 Vp-p, 75 ohms80 MHz HD Pass ThroughGeneralPower requirements 230 V AC, 50/60 Hz (in countries/areas in Europe other than the UK)240 V AC, 50/60 Hz (in the UK and general area)Power consumption 440 WPower consumption (during standby mode)1 WAC outlet

15、s1 switched, 100 W/0.4A MAX(Models for countries/areas in Europe other than the UK)Dimensions430 175 430 mmincluding projecting parts and controlsMass (Approx.)15 kgSupplied accessoriesOperating Instructions (this manual)Quick Setup Guide (1)Optimizer microphone ECM-AC2 (1)FM wire antenna (aerial) (

16、1)AM loop antenna (aerial) (1)AC power cord (mains lead) (1)Remote commander RM-AAP015 (1)R6 (size-AA) batteries (2)Design and specifications are subject to change without notice.70 dBRadioFans.CN 收音机爱 好者资料库3STR-DA1200ESTABLE OF CONTENTS1.SERVICING NOTES.42.GENERAL. 103.DISASSEMBLY3-1.Disassembly Fl

17、ow . 123-2.Case . 133-3.Front Panel Assy. 133-4.S-VIDEO Board . 143-5.Tuner. 143-6.E-VOLUME Board . 153-7.VIDEO Board. 153-8.SP TERMINAL Board . 163-9.ANALOG Board . 163-10. Power Transformer (T01) . 173-11. MAIN Board. 174.TEST MODE. 185.ELECTRICAL ADJUSTMENTS. 216.DIAGRAMS6-1.Block Diagram CONTROL

18、 Section . 226-2.Block Diagram DSP Section . 236-3.Block Diagram HDMI Section . 246-4.Block Diagram ANALOG AUDIO Section . 256-5.Block Diagram POWER AMP Section . 266-6.Block Diagram VIDEO Section . 276-7.Block Diagram DISPLAY Section . 286-8.Block Diagram POWER SUPPLY Section . 296-9.Schematic Diag

19、ram DIGITAL Board (1/5) . 316-10. Schematic Diagram DIGITAL Board (2/5) . 326-11. Schematic Diagram DIGITAL Board (3/5) . 336-12. Schematic Diagram DIGITAL Board (4/5) . 346-13. Schematic Diagram DIGITAL Board (5/5) . 356-14. Printed Wiring Board DIGITAL Board (Component Side) . 366-15. Printed Wiri

20、ng Board DIGITAL Board (Conductor Side) . 376-16. Printed Wiring Board DSP Board . 386-17. Schematic Diagram DSP Board . 396-18. Printed Wiring Board HDMI SW Board . 406-19. Schematic Diagram HDMI SW Board . 416-20. Printed Wiring Board ANALOG Board . 426-21. Schematic Diagram ANALOG Board . 436-22.

21、 Printed Wiring Board MAIN Board . 456-23. Schematic Diagram MAIN Board (1/2) . 466-24. Schematic Diagram MAIN Board (2/2) . 476-25. Printed Wiring Board E-VOLUME Board . 486-26. Schematic Diagram E-VOLUME Board . 496-27. Printed Wiring Board A CLASS AMP Board . 506-28. Schematic Diagram A CLASS AMP

22、 Board . 516-29. Printed Wiring Board POWER AMP Board . 526-30. Schematic Diagram POWER AMP Board . 536-31. Printed Wiring Board BIAS Board . 546-32. Schematic Diagram BIAS Board . 556-33. Printed Wiring Board VIDEO Board . 566-34. Schematic Diagram VIDEO Board (1/3) . 576-35. Schematic Diagram VIDE

23、O Board (2/3) . 586-36. Schematic Diagram VIDEO Board (3/3) . 596-37. Printed Wiring Board S-VIDEO Board . 606-38. Schematic Diagram S-VIDEO Board . 616-39. Printed Wiring Board VIDEO 3 Board . 626-40. Schematic Diagram VIDEO 3 Board . 636-41. Printed Wiring Board DISPLAY Board . 646-42. Schematic D

24、iagram DISPLAY Board . 656-43. Printed Wiring Boards KEY Section . 666-44. Schematic Diagram KEY Section . 676-45. Printed Wiring Boards SPEAKER Section . 686-46. Printed Wiring Boards DC Section . 696-47. Printed Wiring Board AC Board . 706-48. Schematic Diagram POWER SUPPLY Section . 717.EXPLODED

25、VIEWS7-1.Case Section . 927-2.DISPLAY Board Block . 937-3.Front Panel Block . 947-4.VIDEO Board Block . 957-5.ANALOG Board Block . 967-6.MAIN Board Block . 977-7.Heat Sink Block. 988.ELECTRICAL PARTS LIST. 99www.freeservicemanuals.info10/21/2012www.nostatech.nlWorld of free manuals4STR-DA1200ESSECTI

26、ON 1SERVICING NOTESUNLEADED SOLDERBoards requiring use of unleaded solder are printed with the lead-free mark (LF) indicating the solder contains no lead.(Caution: Some printed circuit boards may not come printed withthe lead free mark due to their particular size): LEAD FREE MARKUnleaded solder has

27、 the following characteristics. Unleaded solder melts at a temperature about 40 C higherthan ordinary solder.Ordinary soldering irons can be used but the iron tip has to beapplied to the solder joint for a slightly longer time.Soldering irons using a temperature regulator should be set toabout 350 C

28、.Caution: The printed pattern (copper foil) may peel away ifthe heated tip is applied for too long, so be careful! Strong viscosityUnleaded solder is more viscou-s (sticky, less prone to flow)than ordinary solder so use caution not to let solder bridgesoccur such as on IC pins, etc. Usable with ordi

29、nary solderIt is best to use only unleaded solder but unleaded solder mayalso be added to ordinary solder. MODEL IDENTIFICATIONModelPART No.AEP model2-668-097-0UK model2-668-097-1PART No. Back Panel UPDATE OF SOFTWARE OF THE SYSTEM CONTROLLER (IC2054)Perform operation of the following when the updat

30、e of software of the system controller (IC2054) is necessary.Connect:Procedure:1. Turn off the main power and setting the jig referring to Fig. 1 (Note: Do this setting before connecting jig with the set).2. Remove the KNOB (VOL) ASSY and connect CN717 (M-VOL board) and PC by using the jig.3. Turn o

31、n the main power and perform the operation according to the application.4. After “Please Reset” is displayed, reset switch on the jig is pushed and update is completed.5. Turn off the main power and remove the jig.6. Turn on the main power.JIG (Part No. : J-2501-300-A)for PCCN717M-VOL boardSW2 SW1(R

32、ESET)SW1: up, SW2: downFig.1 Setting for jigwww.freeservicemanuals.info10/21/2012www.nostatech.nlWorld of free manuals5STR-DA1200ESDIGITAL/HDMI SW BOARDS SERVICE POSITIONNote: Follow the disassembly procedure in the numerical order given.In checking the DIGITAL board, remove the HDMI SW board.4DIGIT

33、AL board31five screws (BVTP3 8)2two screws (BVTP3 8)HDMI SW boardDIGITAL boardinsulated sheetwww.freeservicemanuals.info10/21/2012www.nostatech.nlWorld of free manuals6STR-DA1200ESAMP BLOCK SERVICE POSITONIn checking the AMP block, prepare jig (extension cable J-2501-290-A: 500 mm 9 core/J-2501-291-

34、A: 500 mm 12 core).A CLASS AMP boardConnect jig (extension cable J-2501-291-A) to the E-VOLUME board (CNS1201) and A CLASS AMP board (CNS1501).E-VOLUME boardConnect jig (extension cable J-2501-290-A) to the E-VOLUME board (CNS1202) and A CLASS AMP board (CNS1502).DISPLAY boardPOWER SW boardfront pan

35、el blockDISPLAY BOARD SERVICE POSITONwww.freeservicemanuals.info10/21/2012www.nostatech.nlWorld of free manuals7STR-DA1200ESVIDEO BOARD SERVICE POSITONIn checking the VIDEO board, prepare jig (extension cable J-2501-231-A: 300 mm 15 core).ANALOG BOARD SERVICE POSITONIn checking the ANALOG board, rem

36、ove the VIDEO board and S-VIDEO board.Connect jig (extension cable J-2501-231-A) to the VIDEO board (CN6804) and S-VIDEO board (CNS6903).VIDEO boardS-VIDEO boardinsulated sheetANALOG boardinsulated sheetwww.freeservicemanuals.info10/21/2012www.nostatech.nlWorld of free manuals8STR-DA1200ESMAIN/E-VOL

37、UME BOARDS SERVICE POSITONIn checking the MAIN/E-VOLUME board, prepare jig (extension cable J-2501-290-A: 500 mm 9 core/J-2501-291-A: 500 mm 12 core).Note: Be sure to ground the MAIN board with a clip when checking it. MAIN board In checking the board, make two capacitors discharge for electric shoc

38、k prevention. (R: 800 /2W)clipchassisExtension cable (Part No. : J-2501-291-A) to the E-VOLUME board (CNS1201) and A CLASS AMP board (CNS1501).MAIN boardC1402C1402C1401C1401CAUTIONA CLASS AMP boardExtension cable (Part No. : J-2501-290-A) to the E-VOLUME board (CNS1202) and A CLASS AMP board (CNS150

39、2).E-VOLUME boardinsulated sheetJWH1210, JWH1208(Even if it attaches a clip in JWH1208 and attaches it in JWH1210, it is satisfactory.)MAIN boardE-VOLUME boardinsulated sheetclipExtension cable (Part No. : J-2501-291-A) to the E-VOLUME board (CNS1201) and A CLASS AMP board (CNS1501).JWH1210, JWH1208

40、(Even if it attaches a clip in JWH1208 and attaches it in JWH1210, it is satisfactory.)A CLASS AMP boardExtension cable (Part No. : J-2501-290-A) to the E-VOLUME board (CNS1202) and A CLASS AMP board (CNS1502).chassis E-VOLUME board www.freeservicemanuals.info10/21/2012www.nostatech.nlWorld of free

41、manuals9STR-DA1200ESHARNESS SETTINGfront panel blockPOWER SW boardPlease band together so that a ribbon cable does not approach a primary side of POWER SW board.Please band the cable from a VIDEO 3 board together in this position.Please band together so that the ribbon cable from a DIGITAL board can

42、not touch a heat sink.DIGITALboardheat sinkheat sinkPlease band together by purse lock so that a cable cannot touch a heat sink.Please band together so that a primary side cable cannot touch a power transformer.powertransformerPlease band together so that a cable cannot touch a power transformer and

43、 a heat sink.Please band together so that the ribbon cable (5pin) to AC board and the ribbon cable (4 pin) from SP TERMNAL board do not approach the primary side parts of AC board.SP TERMNAL boardAC boardwww.freeservicemanuals.info10/21/2012www.nostatech.nlWorld of free manuals10STR-DA1200ESSECTION

44、2GENERALThis section is extracted frominstruction manual.To remove the coverPress PUSH.When you remove the cover, keep it out of reach from children.Front panelNameFunctionA POWERPress to turn the receiver on or off.B AUTO CAL MIC jackConnects to the supplied optimizer microphone for the Digital Cin

45、ema Auto Calibration function.CTONE MODEAdjusts FRONT BASS and FRONT TREBLE. Press TONE MODE repeatedly to select BASS or TREBLE, then turn TONE to adjust the level.TONEDMEMORY/ENTERPress to operate a tuner (FM/AM).TUNING MODETUNINGERemote sensor Receives signals from remote commander.F DIMMERPress

46、to adjust brightness of the display.GSLEEPPress to activate the SLEEP function.HSUR BACK DECODINGPress to activate SB DECODING.IDisplay windowThe current status of the selected component or a list of selectable items appears here.J2CHPress to select sound field.A.F.D.MOVIEMUSICKDISPLAYPress to selec

47、t the input mode when the same components are connected to both digital and analog jacks.INPUT MODENameFunctionLMULTI CH INPress to select the audio input signal from the component connected to the MULTI CHANNEL INPUT jack.MA.DIRECTPress to listen to high quality analog sound.NPHONES jackConnects to

48、 headphones.OSPEAKERS (OFF/A/B/A+B)Press to select A, B, A+B, OFF of the front speakers.PVIDEO 3 IN/ PORTABLE AV IN jackConnect to a portable audio/video component such as a camcorder or video game.QMULTI CHANNEL DECODING lampLights up when multichannel audio signals are decoded.RINPUT SELECTORTurn

49、to select the input source to play back.SMASTER VOLUMETurn to adjust the volume level of all speakers at the same time.NameFunctionRear panelADIGITAL INPUT/OUTPUT sectionOPTICAL IN/OUT jacksConnects to a DVD player, Super Audio CD player, etc. The COAXIAL jack provides a better quality sound.COAXIAL

50、 IN jacksHDMI IN/MONITOR OUT jacksConnects to a DVD player, or a satellite tuner. An image and the sound are output to TV or a projector.BANTENNA sectionFM ANTENNA jackConnects to the FM wire antenna (aerial) supplied with this receiver.AM ANTENNA jackConnects to the AM loop antenna (aerial) supplie