Sony-STRDE695-rec-sm 维修电路原理图.pdf

《Sony-STRDE695-rec-sm 维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Sony-STRDE695-rec-sm 维修电路原理图.pdf（68页珍藏版）》请在收音机爱好者资料库上搜索。

1、1SERVICE MANUALUS ModelCanadian ModelAEP ModelUK ModelE ModelAustralian ModelChinese ModelTourist ModelSTR-DE695FM STEREO/FM-AM RECEIVERAUDIO POWER SPECIFICATIONSPOWER OUTPUT AND TOTALHARMONIC DISTORTION:With 8 ohm loads, both channels driven, from20 20,000 Hz; rated 90 watts per channelminimum RMS

2、power, with no more than0.09 % total harmonic distortion from 250milliwatts to rated output (Models of areacode US only).Amplifier sectionPOWER OUTPUTModels of area code US, CNDRated Power Output at Stereo Mode(8 ohms 20 Hz 20 kHz, THD 0.09 %)90 W + 90 WReference Power Output(8 ohms 20 Hz 20 kHz, TH

3、D 0.09 %)FRONT 1) :90 W/chCENTER 1) :90 WSURR 1) :90 W/chSURR BACK 1) :90 W(8 ohms 1 kHz, THD 0.7 %)FRONT 1) :100 W/chCENTER 1) :100 WSURR 1) :100 W/chSURR BACK 1) :100 WSPECIFICATIONSModels of area code AEP, UKRated Power Output at Stereo Mode(8 ohms 1 kHz, THD 0.7 %)120 W + 120 W 2)Reference Power

4、 Output 2)(8 ohms 1 kHz, THD 0.7 %)FRONT 1) :120 W/chCENTER 1) :120 WSURR 1) :120 W/chModels of area code CHRated Power Output at Stereo Mode(8 ohms 1 kHz, THD 0.7 %)120 W + 120 W 2)110 W + 110 W 3)Reference Power Output 2)(8 ohms 1 kHz, THD 10 %)FRONT 1) :140 W/chCENTER 1) :140 WSURR 1) :140 W/chMo

5、dels of area code SP, MYRated Power Output at Stereo Mode(8 ohms 1 kHz, THD 0.7 %)100 W + 100 W 2)Reference Power Output 2)(8 ohms 1 kHz, THD 10 %)FRONT 1) :120 W/chCENTER 1) :120 WSURR 1) :120 W/chVer 1.1 2003. 059-877-239-022003E04-1 2003. 05Sony CorporationHome Audio CompanyPublished by Sony Engi

6、neering CorporationManufactured under license from Dolby Laboratories.“Dolby”, “Pro Logic” and the double-D symbol aretrademarks of Dolby Laboratories.“DTS”, “DTS-ES Extended Surround” and “Neo:6” aretrademarks of Digital Theater Systems, Inc. Continued on next page RadioFans.CN 收音机爱 好者资料库2STR-DE695

7、Ver 1.1Models of area code TWRated Power Output at Stereo Mode(8 ohms 1 kHz, THD 0.7 %)120 W + 120 W 2)Reference Power Output 2)(8 ohms 1 kHz, THD 10 %)FRONT 1) :140 W/chCENTER 1) :140 WSURR 1) :140 W/chModels of area code AUSRated Power Output at Stereo Mode(8 ohms 20 Hz 20 kHz, THD 0.09 %)100 W +

8、100 W 2)(8 ohms 1 kHz, THD 0.7 %)120 W + 120 W 2)Reference Power Output 2)(8 ohms 20 Hz 20 kHz, THD 0.09 %)FRONT 1) :100 W/chCENTER 1) :100 WSURR 1) :100 W/ch(8 ohms 1 kHz, THD 10 %)FRONT 1) :140 W/chCENTER 1) :140 WSURR 1) :140 W/chModels of other area codeRated Power Output at Stereo Mode(8 ohms 1

9、 kHz, THD 0.7 %)110 W + 110 W 2)Reference Power Output 2)(8 ohms 1 kHz, THD 10 %)FRONT 1) :130 W/chCENTER 1) :130 WSURR 1) :130 W/ch1) Depending on the sound field settings and thesource, there may be no sound output.2) Measured under the following conditions:Area codePower requirementsE2, E3, JE, A

10、US240 V AC, 50 HzSP, MY, AEP, UK,230 V AC, 50 HzAR, CHTW110 V AC, 60 HzUS, CND, MX120 V AC, 60 Hz3) Measured under the following conditions:Area codePower requirementsCH220 V AC, 50 HzFrequency responseMULTI CH IN,10 Hz 70 kHzCD/SACD, AUX,+0.5/2 dB (with soundMD/TAPE, DVD,field and equalizerVIDEO 1,

11、 2, 3bypassed)Inputs (Analog)MULTI CH IN,Sensitivity: 500 mVCD/SACD, AUX,Impedance: 50 kilohmsMD/TAPE, DVD,S/N 4) : 96 dBVIDEO 1, 2, 3(A, 500 mV 5) )4) INPUT SHORT (with sound field and equalizerbypassed).5) Weighted network, input level.Inputs (Digital)DVD (Coaxial)Sensitivity: Impedance: 75 ohmsS/

12、N: 100 dB(A, 20 kHz LPF)VIDEO 2, CD/SACD,Sensitivity: MD/TAPE (Optical)Impedance: S/N: 100 dB(A, 20 kHz LPF)Outputs (Analog)MD/TAPE (OUT),Voltage: 500 mVVIDEO 1 (AUDIO OUT)Impedance: 10 kilohmsSUB WOOFER,Voltage: 2 VSURR BACK (Except forImpedance: 1 kilohmsmodels of area code US,CND)Outputs (Digital

13、)MD/TAPE (Optical)Sensitivity: EQGain levels:10 dB, 0.5 dB stepFM tuner sectionTuning range87.5 - 108.0 MHzAntenna terminals75 ohms, unbalancedIntermediate Frequency10.7 MHzSensitivityMono:18.3 dBf, 2.2 V/75 ohmsStereo:38.3 dBf, 22.5 V/75 ohmsUsable sensitivity11.2 dBf, 1 V/75 ohmsS/NMono:76 dBStere

14、o:70 dBHarmonic distortion at 1 kHzMono:0.3%Stereo:0.5%Separation45 dB at 1 kHzFrequency response30 Hz 15 kHz,+0.5/2 dBSelectivity60 dB at 400 kHzAM tuner sectionTuning rangeModels of area code US, CNDWith 10-kHz tuning scale: 530 1710 kHz 6)With 9-kHz tuning scale:531 1710 kHz 6)Models of area code

15、 E2, E3, JEWith 10-kHz tuning scale: 530 1610 kHz 6)With 9-kHz tuning scale:531 1602 kHz 6)Models of area code AEP, UK, SP, MY, CH, TW, AUSWith 9-kHz tuning scale:531 1602 kHzModels of area code AR, MXWith 10-kHz tuning scale: 530 1610 kHzAntennaLoop antennaIntermediate Frequency450 kHzUsable sensit

16、ivity50 dB/m (at 1,000 kHz or999 kHz)S/N54 dB (at 50 mV/m)Harmonic distortion0.5 % (50 mV/m, 400 Hz)SelectivityAt 9 kHz:35 dBAt 10 kHz:40 dB6) You can change the AM tuning scale to 9 kHz or10 kHz. After tuning in any AM station, turn offthe receiver. Hold down PRESET TUNING + andpress ?/1 . All pres

17、et stations will be erased whenyou change the tuning scale. To reset the scale to10 kHz (or 9 kHz), repeat the procedure.Video sectionInputsVideo:1 Vp-p, 75 ohmsS-video:Y: 1 Vp-p, 75 ohmsC: 0.286 Vp-p, 75 ohmsComponent Video (Except for models ofarea code AEP, UK):Y:1 Vp-p, 75 ohmsPB/B-Y:0.7 Vp-p, 7

18、5 ohmsPR/R-Y:0.7 Vp-p, 75 ohmsOutputsVideo:1 Vp-p, 75 ohmsS-video:Y: 1 Vp-p, 75 ohmsC: 0.286 Vp-p, 75 ohmsComponent Video (Except for models ofarea code AEP, UK):Y:1 Vp-p, 75 ohmsPB/B-Y:0.7 Vp-p, 75 ohmsPR/R-Y:0.7 Vp-p, 75 ohmsRadioFans.CN 收音机爱 好者资料库3STR-DE695Ver 1.1GeneralPower requirementsArea cod

19、ePower requirementsUS, CND, MX120 V AC, 60 HzAEP, UK230 V AC, 50/60 HzSP, MY, AR, CH220 230 V AC, 50/60 HzE2, E3, JE120/220/240 V AC, 50/60 HzTW110 V AC, 50/60 HzAUS240 V AC, 50 HzPower consumptionArea codePower consumptionUS245 WCND330 VAMX230 WAEP, UK, AR, CH, AUS250 WSP, MY210 WE2, E3, JE240 WTW6

20、00 WPower consumption (during standby mode)0.3 W (when “P.SAVE” in theCUSTOM menu is set to “ON”)AC outlets (Except for models of area code AR, KR)1 switched, 120 W/1 A MAX(Models of area code US, CND)1 switched, 100 W MAX(Models of other area code)Dimensions430 157.5 310 mm(16 7/8 6 2/8 12 2/8 in.)

21、including projecting partsand controlsMass (Approx.)8.0 kg (17 lb 11 oz)(Models of area code US, CND)8.5 kg (18 lb 12 oz)(Models of other area code)Supplied accessoriesFM wire antenna (1)AM loop antenna (1)Remote commander (1) RM-PP412 (Models of area code US, CND, E2, E3, MX, AR) RM-U307 (Models of

22、 other area code)R6 (size-AA) batteries (2)Design and specifications are subject to changewithout notice. AbbreviationCND: Canadian modelAUS: Australian modelCH: Chinese modelSP: Singapore modelMY: Malaysia modelTW: Taiwan modelE2: AC 120 V area in E modelE3: AC 240 V area in E modelJE: Tourist mode

23、lAR: Argentina modelMX: Mexican model4STR-DE695MODEL IDENTIFICATION BACK PANEL Part No.MODELPART No.US4-244-270-0sCanadian4-244-270-1sAEP4-244-270-2sUK4-244-270-3sSingapore, Malaysia4-244-270-4sChinese4-244-270-5sTaiwan4-244-270-6sE2, E34-244-270-8sMexican4-244-270-9sArgentina4-244-311-0sTourist4-24

24、4-311-1sAustralian4-244-311-2s1.5 k0.15 FACvoltmeter(0.75 V)To Exposed MetalParts on SetEarth GroundSAFETY CHECK-OUTAfter correcting the original service problem, perform the follow-ing safety check before releasing the set to the customer:Check the antenna terminals, metal trim, “metallized” knobs,

25、 screws,and all other exposed metal parts for AC leakage.Check leakage as described below.LEAKAGE TESTThe AC leakage from any exposed metal part to earth ground andfrom all exposed metal parts to any exposed metal part having areturn to chassis, must not exceed 0.5 mA (500 microampers.).Leakage curr

26、ent can be measured by any one of three methods.1.A commercial leakage tester, such as the Simpson 229 or RCAWT-540A. Follow the manufacturers instructions to use theseinstruments.2.A battery-operated AC milliammeter. The Data Precision 245digital multimeter is suitable for this job.3.Measuring the

27、voltage drop across a resistor by means of aVOM or battery-operated AC voltmeter. The “limit” indica-tion is 0.75 V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are ex-amples of a passive VOM that is suitable. Nearly all batteryoperated digital multim

28、eters that have a 2 V AC range are suit-able. (See Fig. A)SAFETY-RELATED COMPONENT WARNING!COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINEWITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND INTHE PARTS LIST ARE CRITICAL TO SAFE OPERATION.REPLACE THESE COMPONENTS WITH SONY PARTS WHOSEPART NUMBERS APPEAR AS SHOW

29、N IN THIS MANUAL ORIN SUPPLEMENTS PUBLISHED BY SONY.ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT!LES COMPOSANTS IDENTIFIS P AR UNE MARQUE 0 SUR LESDIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONTCRITIQUES POUR LA SCURIT DE FONCTIONNEMENT. NEREMPLACER CES COMPOSANTS Q UE PAR DES PICES SONYDONT LES

30、 NUMROS SONT DONNS DANS CE MANUEL OUDANS LES SUPPLMENTS PUBLIS P AR SONY.Fig. A. Using an AC voltmeter to check AC leakage.Ver 1.15TABLE OF CONTENTS1. GENERALMain unit . 6Remote button description.72. DISASSEMBLY2-1. Case . 92-2. Front Panel Section . 102-3. Back Panel. 102-4. Digital Board. 112-5.

31、Standby Board. 112-6. Main Board . 122-7. SB AMP Board (US, Canadian model only). 123. TEST MODE. 134. DIAGRAMS4-1. IC Pin Descriptions . 144-2. Block Diagram Tuner/Audio Section . 194-3. Block Diagram Digital Section . 204-4. Block Diagram Key/Display Section . 214-5. Block Diagram Video Section .

32、224-6. Block Diagram Power Section . 234-7. Circuit Boards Location . 244-8. Printed Wiring Boards Main Section . 254-9. Schematic Diagram Main Section (1/3) . 264-10. Schematic Diagram Main Section (2/3) . 274-11. Schematic Diagram Main Section (3/3) . 284-12. Schematic Diagram Digital Section (1/3

33、) . 294-13. Schematic Diagram Digital Section (2/3) . 304-14. Schematic Diagram Digital Section (3/3) . 314-15. Printed Wiring Board Digital Section (1/2) . 324-16. Printed Wiring Board Digital Section (2/2) . 334-17. Printed Wiring Boards Video Section . 344-18. Schematic Diagram Video Section . 35

34、4-19. Printed Wiring Board S-video Section . 364-20. Schematic Diagram S-video Section . 374-21. Printed Wiring Boards Speaker Section . 384-22. Schematic Diagram Speaker Section . 394-23. Printed Wiring Boards Display Section . 404-24. Schematic Diagram Display Section . 414-25. Printed Wiring Boar

35、ds Power Section . 424-26. Schematic Diagram Power Section . 434-27. IC Block Diagrams. 445. EXPLODED VIEWS5-1. Case Section . 475-2. Front Panel Section . 485-3. Chassis Section-1 . 495-4. Chassis Section-2 . 506. ELECTRICAL PARTS LIST. 51STR-DE695Ver 1.16STR-DE695SECTION 1GENERALThis section is ex

36、tractedfrom instruction manual.7STR-DE695Ver 1.18STR-DE6959STR-DE695Note : This set can be disassemble according to the following sequence.SECTION 2DISASSEMBLY2-1. CASE2-1.CASE(Page 9)2-2.FRONT PANEL SECTION(Page 10)2-3.BACK PANEL(Page 10)SET2-5.STANDBY BOARD(Page 11)2-4.DIGITAL BOARD(Page 11)2-6.MA

37、IN BOARD(Page 12)2-7.SB AMP BOARD(Page 12)Note : Follow the disassembly procedure in the numerical order given.1 two screws (case 3 TP2)2 three screws (case 3 TP2)3 two screws (case 3 TP2)4 case10STR-DE6952-2. FRONT PANEL SECTION2-3. BACK PANEL9 front panel section53 two screws (BVTP3 x 8)6 two scre

38、ws (BVTP3 x 8)2 CNP7918 CN2017 VIDEO3 board4 five screws (BVTP3 x 8)1 CNS5051 CNP9012 CN8063 CNP8074 CNP5015 CNS5086 CNS5098 two screws (BVTP3 x 8)qs two screws (BVTP3 x 8)7 two screws (BVTP3 x 8)9 five screws (BVTP3 x 8)0 five screws (BVTP3 x 8)qd screw (BVTP3 x 8)qa screw (BVTP3 x 8)qf back panel1

39、1STR-DE6952-4. DIGITAL BOARD1 CNS5057 CNP5016 CNP5022 CNP5063 CNP5104 CNP5079 screw (BVTP3 x 8)0 bracket (digital)8 DIGITAL board5 screw (BVTP3 x 8)6 STANDBY board1 CNP9152 CNP8023 CNP9034 CNP9025 three screws (BVTP3 x 6)2-5. STANDBY BOARD12STR-DE6958 MAIN board1 CN9082 CNP8023 CNP5036 screw (BVTP3

40、x 6)5 two screws (BVTP3 x 6)4 two screws (BVTP3 x 6)7 two screws (BVTP3 x 6)2-6. MAIN BOARD2-7. SB AMP BOARD (US, Canadian MODEL ONLY)1 CN7212 CN7204 screw (BVTP3 x 8)6 screw (BVTP3 x 8)7 bracket (PWB)5 bracket (PWB)3 three screws (transister)8 SB AMP boardVer 1.113STR-DE695SECTION 3TEST MODEFACTORY

41、 PRESET MODE* All preset contents are reset to the default setting.* Procedure:While depressing the SURR BACK DECODING and the TUNING -buttons simultaneously, press the ?/1 button to turn on themain power.The message “FACTORY” appears for a moment and the presentcontents are reset to the default val

42、ues.AM CHANNEL STEP 9 kHz/10 kHz SELECTIONMODE (US, Canadian, E model only)* Either the 9 kHz step or 10 kHz step can be selected for the AMchannel step.* Procedure:Press the TUNER FM/AM button to set AM and press the ?/1button to turn off the main power.While depressing the TUNING + button or thePR

43、ESET TUNING + button, press the ?/1 button to turn on themain power.Either the message “9k STEP” or “10k STEP” appears for amoment and select the desired step.SPEAKER SIZE SELECTION MODE* Either the normal speaker or micro satellite speaker can be se-lected.* Procedure:While depressing the MAIN MENU

44、 button, press the ?/1 but-ton to turn on the main power.Either the message “NORM. SP.” or “MICRO SP.” appears for amoment and select the desired speaker size.FLUORESCENT INDICATOR TUBE TEST MODE* All fluorescent segments are tested.When this test is activated, all segments light on at the sametime,

45、 then each segment lights on one after another.* Procedure:While depressing the SURR BACK DECODING and the DISPLAYbuttons simultaneously, press the ?/1 button to turn on themain power.1.ALL segments light on.2CH LED light on.2.Press the DIMMER button, confirm display.A.F.D. and MUSIC LED light on.3.

46、Press the VIDEO 1 button, confirm display.MOVIE and SURR BACK DECODING LED light on.SWLSLCRSSBSRL F EdBkHzmft.MHzDDDDSPSP ASP BOPTSLEEPCOAXMULTI CH IN12 D.RANGEEQSTEREOMONORDSDIGITALMEMORYEXPROLOGICII DTS-ESNEO:6 MPEG-2 AACLSLRSRdBHzft.SP ASP BCOAX1D.RANGEEQMONOMEMORYEXII-ESNEO:6-2SWCSSBL F EkmMHzDD

47、DDSPOPTSLEEPMULTI CH IN2STEREORDSDIGITALPROLOGIC DTSMPEGAAC4.Press the DIMMER button, all segments and all LEDs light off.5.Every pressing the DIMMER button turns on each segment andLED one after another in the same order.SOUND FIELD CLEAR MODE* The preset sound field is cleared when this mode is ac

48、tivated.Use this mode before returning the product to clients uponcompletion of repair.* Procedure:While depressing the 2CH button, press the ?/1 button to turnon the main power.The message “SF. CLR.” appears for a moment.SOFTWARE VERSION DISPLAY MODE* The software version is displayed.* Procedure:W

49、hile depressing the A.F.D. and the DISPLAY buttons simul-taneously, press the ?/1 button to turn on the main power.The destination and the software version are displayed for amoment.AUTOBETICAL MODE (AEP, UK model only)* When this mode is used, the receiver scans the broadcasts thatcan be received b

50、y the tuner, and sets up the broadcasts.Be sure to start scanning after connecting the antenna.* Procedure:Check that the antenna is connected.While depressing the MEMORY button, press the ?/1 buttonto turn on the main power.The message “AUTO-BETICAL SELECT” appears for a mo-ment and the receiver st