sony_pha-1a_pha-1aeu_ver.1.1_headphone_amplifier.pdf

上传人:大海狮的怀旧 文档编号:178157 上传时间:2024-07-20 格式:PDF 页数:42 大小:2.58MB
下载 相关 举报
sony_pha-1a_pha-1aeu_ver.1.1_headphone_amplifier.pdf_第1页
第1页 / 共42页
sony_pha-1a_pha-1aeu_ver.1.1_headphone_amplifier.pdf_第2页
第2页 / 共42页
sony_pha-1a_pha-1aeu_ver.1.1_headphone_amplifier.pdf_第3页
第3页 / 共42页
亲,该文档总共42页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

《sony_pha-1a_pha-1aeu_ver.1.1_headphone_amplifier.pdf》由会员分享,可在线阅读,更多相关《sony_pha-1a_pha-1aeu_ver.1.1_headphone_amplifier.pdf(42页珍藏版)》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL Sony Corporation Published by Sony Techno Create Corporation PHA-1A/1AEU SPECIFICATIONS 9-896-144-02 2015H33-1 2015.08 US Model Canadian Model E Model Australian Model Chinese Model Russian Model PHA-1A AEP Model UK Model PHA-1AEU Ver. 1.1 2015.08 Frequency range 10 Hz 100 kHz Support

2、ed impedance 8 ? - 600 ? Maximum output*1 (when using the built-in lithium-ion rechargeable battery) Approx. 148 mW + 148 mW (8 ?, 10% distortion) Approx. 80 mW + 80 mW (32 ?, 1% distortion) Approx. 16.4 mW + 16.4 mW (300 ?, 10% distortion) Output jack Stereo mini jack*2 ( (headphones) *2 Only a 3-p

3、ole stereo mini plug is supported. Other plugs, including 2-pole mini plug or 4-pole stereo mini plug, are not supported. Input jack/port Computer/WALKMAN/Xperia connecting port iPhone/iPad/iPod connecting port Operating temperature 0 C to 40 C (32F to 104F) Charging temperature 5 C to 35 C (41F to

4、95F) Power source DC 3.7 V: built-in lithium-ion rechargeable battery Rated power consumption (AEP, Russian, UK, E, Australian and Chinese models) 7 W DC 5 V: when charging via USB Battery life Approx. 6 hours*3 *3 when using the unit at 1 mW + 1 mW output (24 ?). Time may vary, depending on the imm

5、ediate environment or conditions of use. Charging time When connected to a computer: Approx. 3.5 hours*4 When connected to an AC outlet using the recommended USB AC adaptor (sold separately): Approx. 2 hours*3 *4 Time required for empty battery to recharge while the unit is off. Dimensions Approx. 6

6、2 mm 18.5 mm 109 mm Mass Approx. 145 g (5.11 oz) Supported sampling frequencies/bit Maximum 192 kHz/24 bit Included items Digital cable for WALKMAN (1) Digital cable for Xperia (1) Micro-USB cable (1) Silicone belt (2) Protection sheet (1) Startup Guide (1) Reference Guide (1) Remove the included it

7、ems other than the unit by opening the tray under the unit and removing them. Operating environment Compliant OS: Windows 8.1/Windows 8.1 Pro/Windows 8/Windows 8 Pro Windows 7 Starter (SP1 or later)/Home Basic (SP1 or later)/Home Premium (SP1 or later)/ Professional (SP1 or later)/Ultimate (SP1 or l

8、ater) Windows Vista Home Basic (SP2 or later)/Home Premium (SP2 or later)/Business (SP2 or later)/Ultimate (SP2 or later) Mac OS X (v10.6.8 or later) CPU: Intel Core 2 Processor 1.6 GHz or better Memory: 1 GB or better USB port (USB 2.0 High Speed) One of the above OS need to be installed to the com

9、puter at the factory. The unit is not guaranteed to operate with all computers. The unit is not guaranteed to operate with home built computers, operating systems that are personally upgraded, or multiple operating systems. The unit is not guaranteed to operate with functions such as standby, sleep,

10、 or hibernation, on any computer. Design and specifications are subject to change without notice. (2 1/2 3/4 4 3/8 in) (w/h/d, projecting parts are not included) *1 When the GAIN select switch is set to “LOW”, the maximum output will be approx. 150 mV + 150 mV. (PHA-1AEU only) PORTABLE HEADPHONE AMP

11、LIFIER CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. Photo: PHA-1A PHA-1A/1AEU 2 Compatible iPhone/iPad/iPod models You can use the unit with only the following models. Update your iPhone, iPad or iPod to the latest software before use

12、. iPhone 6 Plus iPhone 6 iPhone 5s iPhone 5c iPhone 5 iPhone 4s iPhone 4 iPhone 3GS iPhone 3G iPhone iPad Air 2 iPad mini 3 iPad Air iPad mini 2 iPad mini iPad (4th generation) iPad (3rd generation) iPad 2 iPad iPod touch (1st through 5th generation) iPod classic 120GB/160GB (2009) iPod nano (2nd th

13、rough 7th generation) (As of December 2014) This unit is compatible only with the audio playback functions iPhones/iPads/iPods. Depending on the Apple product, there may be significant electric power required when starting the communication connected with the unit. The battery power of the unit may

14、be drained and the unit may turn off if you connect the Apple product to the unit when the battery power is low. In this case, charge the unit or use the USB AC adaptor to connect with the Apple product. Trademark Notices WALKMAN and WALKMAN logo are registered trademarks of Sony Corporation. “Xperi

15、a” and “Xperia Tablet” are trademarks of Sony Mobile Communications AB. iPad, iPhone, iPod, iPod classic, iPod nano, iPod touch, and Retina are trademarks of Apple Inc., registered in the U.S. and other countries. iPad Air, and iPad mini are trademarks of Apple Inc. “Made for iPod,” “Made for iPhone

16、,” and “Made for iPad” mean that an electronic accessory has been designed to connect specifically to iPod, iPhone or iPad, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safe

17、ty and regulatory standards. Please note that the use of this accessory with iPod, iPhone, or iPad may affect wireless performance. Macintosh and Mac OS are trademarks of Apple Inc., registered in the U.S. and other countries. Microsoft, Windows and Windows Vista are registered trademarks or tradema

18、rks of Microsoft Corporation in the United States and/or other countries. All other trademarks and registered trademarks are trademarks or registered trademarks of their respective holders. In this manual, TM and marks are not specified. SAFETY-RELATED COMPONENT WARNING! COMPONENTS IDENTIFIED BY MAR

19、K 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT! LES COMPOSANT

20、S IDENTIFIS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONT CRITIQUES POUR LA SCURIT DE FONC- TIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PICES SONY DONT LES NUMROS SONT DON- NS DANS CE MANUEL OU DANS LES SUPPLMENTS PUBLIS PAR SONY. 1. SERVICING NOTES . 3 2. DISASS

21、EMBLY 2-1. Disassembly Flow . 4 2-2. Bottom Panel . 4 2-3. Case Block, MAIN Board Block . 5 2-4. Battery Assy (BAT1) . 5 2-5. MAIN Board . 6 2-6. Plate Middle Assy . 7 2-7. HP JACK Board . 7 3. DIAGRAMS 3-1. Block Diagram . 9 3-2. Printed Wiring Boards (PHA-1A) . 11 3-3. Schematic Diagram - MAIN Sec

22、tion (1/4) (PHA-1A) - . 12 3-4. Schematic Diagram - MAIN Section (2/4) (PHA-1A) - . 13 3-5. Schematic Diagram - MAIN Section (3/4) (PHA-1A) - . 14 3-6. Schematic Diagram - MAIN Section (4/4) (PHA-1A) - . 15 4. EXPLODED VIEWS 4-1. MAIN Board Section . 23 4-2. Battery Section . 24 5. ELECTRICAL PARTS

23、LIST . 25 Accessories are given in the last of the electrical parts list. TABLE OF CONTENTS Note: Refer to service manual supplement-1 for printed wiring board, schematic diagram and electrical parts list of PHA-1AEU. Ver. 1.1 PHA-1A/1AEU 3 SECTION 1 SERVICING NOTES UNLEADED SOLDER Boards requiring

24、use of unleaded solder are printed with the lead- free mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size) : LEAD FREE MARK Unleaded solder has the following characteristics. Unleaded solde

25、r melts at a temperature about 40 C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350 C. Caution: The printed pattern (copper fo

26、il) may peel away if the heated tip is applied for too long, so be careful! Strong viscosity Unleaded solder is more viscous (sticky, less prone to fl ow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. Usable with ordinary solder It is best to use only u

27、nleaded solder but unleaded solder may also be added to ordinary solder. The SERVICING NOTES contains important information for servicing. Be sure to read this section before repairing the unit. DESTINATION ABBREVIATIONS The following abbreviations for model destinations are used in this service man

28、ual. Abbreviations AUS : Australian model CH : Chinese model CND : Canadian model LA : Latin American model RU : Russian model NOTE FOR PARTS REPAIR OF HP JACK AND VOLUME BOARDS When HP JACK and VOLUME boards installed in this unit are defective, replace the complete mounted board or the whole parts

29、 including the complete mounted board. The mounted parts on the HP HACK and VOLUME boards cannot replace with single. NOTE FOR REPLACING THE MAIN BOARD OR CASE When replacing the MAIN board or case, be sure to replace both parts simultaneously. Among the repair parts, the MAIN board and case are sup

30、plied as one unit. NOTE FOR REPLACING THE ELECTRICAL PARTS ON THE MAIN BOARD The following parts on the MAIN board cannot replace with sin- gle. When these parts are damaged, replace the complete mounted board. (Q003, Q004: PHA-1AEU only) IC001, IC002, IC003, IC101, IC201, IC301, IC401, IC403, IC500

31、, IC501, IC502, IC503, IC505, IC506, IC507, IC601, IC602, IC701, IC702, Q001, Q002, Q003, Q004 NOTE OF REPLACING THE IC704 ON THE MAIN BOARD Replacement of IC704 on the MAIN board used in this unit re- quires a special tool. Ver. 1.1 PHA-1A/1AEU 4 SECTION 2 DISASSEMBLY This set can be disassembled i

32、n the order shown below. 2-1. DISASSEMBLY FLOW Note: Follow the disassembly procedure in the numerical order given. 2-2. BOTTOM PANEL SET 2-3. CASE BLOCK, MAIN BOARD BLOCK (Page 5) 2-7. HP JACK BOARD (Page 7) 2-4. BATTERY ASSY (BAT1) (Page 5) 2-5. MAIN BOARD (Page 6) 2-6. PLATE MIDDLE ASSY (Page 7)

33、2-2. BOTTOM PANEL (Page 4) 1 two screws (M1.4 ? 4) 2 bottom panel PHA-1A/1AEU 5 2-3. CASE BLOCK, MAIN BOARD BLOCK 1 screw (M1.4 ? 2.5) 4 case block 3 MAIN board block 2 Push the MAIN board block in the direction of the arrow. Note: When replacing the case, be sure to replace the MAIN board simultane

34、ously. Among the repair parts, the MAIN board and case are supplied as one unit. 2-4. BATTERY ASSY (BAT1) 3 Lift up the battery assy (BAT1) in the direction of the arrow. 2 Peel off the battery assy (BAT1) from the frame sheet. frame block 4 connector (CN702) Frame block battery installation side co

35、nnector (CN702) Push the wire inside of the frame. frame battery assy (BAT1) ? ?ire settin? ? ?astin? ?osition o? battery c?s?ion battery assy (BAT1) battery cushion guide line (center) 5 battery assy (BAT1) Note 2: When removing the battery assy (BAT1), the battery assy (BAT1) cannot be reused. Be

36、sure to replace them with new parts. 1 battery cushion Note 1: When removing the battery cushion from the battery assy (BAT1), be sure to replace the battery assy (BAT1) with new parts. PHA-1A/1AEU 6 2-5. MAIN BOARD Note 1: When replacing the MAIN board, be sure to replace the case simultaneously. A

37、mong the repair parts, the MAIN board and case are sup- plied as one unit. 4 four screws (M1.7 ? 4.5) 5 Lift up the MAIN board in the direction of the arrow. 7 connector (CN002) 6 connector (CN001) hole boss boss hole 3 connector (CN303) 2 woofer sheet 1 frame sheet 8 MAIN board Note 2: When install

38、ing the MAIN board, align two holes and two bosses. Frame block battery installation side Frame block MAIN board installation side ? connector (CN002) connector (CN303) MAIN board HP JACK board Pass the wire under the MAIN board. ? ? woofer sheet connector (CN001) connector (CN301) frame sheet guide

39、 line guide line PHA-1A/1AEU 7 2-6. PLATE MIDDLE ASSY 2-7. HP JACK BOARD 4 plate middle assy 1 screw (M1.7 ? 4.5) frame block 1 screw (M1.7 ? 4.5) 1 screw (M1.7 ? 4.5) 2 connector (CN301) 3 light guide Frame block MAIN board installation side 1 screw (M1.7 ? 4.5) 2 HP JACK board ditch boss Frame blo

40、ck MAIN board installation side frame block PHA-1A/1AEU 8 MEMO PHA-1A/1AEU PHA-1A/1AEU 99 SECTION 3 DIAGRAMS 3-1. BLOCK DIAGRAM VOLUME BOARD 3 2 4 1 CN601 INPUT (FOR PC/WALKMAN/Xperia) 3 2 1 CN602 INPUT (FOR iPhone/iPad/iPod) USBDPSDAT_IN_AUX BCLK_IN_AUX LRCK_IN_AUX MCLK_IN AUX_SW 689 USBDM5 XMDAC_S

41、DOUT0 93XMDAC_SCLK 94XMDAC_LRCK 95XMDAC_MCLK XPEE_D0 XPEE_D7 XPEE_A0 XPEE_A15 VCCHSRT2 VCCA_U207 VDD33_VF XPEE_WRN83 XPEE_CEN82 XPEE_RDN84 B+ SWITCH Q404, 405 B+ SWITCH Q595, 710 B+ SWITCH Q711 713 B+ SWITCH Q401, 403 B+ SWITCH Q501, 502 FLASH MEMORY IC602 WE CE OE DQ0 DQ7 A0 A15 7 30 32 CP_RST21 CP

42、_SDA13 CP_SCL12 MFI IC403 RST SDA SCL 7 2 6 26SDAT_OUT 27BCLK_OUT 28LRCK_OUT 18MCLK_OUT 54 23 24 25 17 16XGPIO_7 1XSCO 100XSCI 43MUTE 1 44MUTE 2 UHD+38 UHD37 VBUS-OFF48 45LED1 AUX SWITCH Q402 AUDIO AMP IC001 HEADPHONE AMP IC002 MUTING SWITCH Q002 GAIN CONTROL IC101 OVER VOLTAGE PROTECT IC704 OVER CU

43、RRENT PROTECT IC509 CURRENT LIMIT SWITCH Q719 721 CURRENT LIMIT CONTROL Q718 X601 12MHz 7CF2 6CF1 X401 12MHz 1SERIAL-SW 46BATT_CK USB AUDIO PROCESSOR IC601 USB CONTROLLER IC401 DIN BCKIN LRCIN SCLK 2 3 1 5 D/A CONVERTER IC301 R-CH R-CH R-CH VDD33_VF 2/RESVDD33_VF D+ D VBUS VOLTAGE LEVEL DETECT IC705

44、 DC/DC CONVERTER IC507 POWER CONTROL Q508, 509 POWER CONTROL IC511 +3.3V REGULATOR IC510 +5V REGULATOR IC502 RESET SIGNAL GENERATOR IC402 RESET SWITCH Q722, 723 3 2 1 CN701 DC IN 5V DC/DC CONVERTER IC500 S591 (WALKMAN/Xperia DETECT) S592 (SERIAL No. WRITE) 17VOUTLP LOUT 16VOUTLN 12VOUTRP 13VOUTRN C_

45、LED RC4 RC3 1 5 6 RC27 CHD_PGOOD4 CHARGE CONTROLLER IC702 12D+ 9RC0 11D 2TEMP LIN PWR_CTRL HP JACK BOARD LEFT RIGHT DC SERVO IC003 8RC1 OUT OUT 10 11 BATTERY CHARGER, POWER CONTROLLER IC701 13IN 5EN2 12ILIM 3BAT 6EN1 9CHG 7PGOOD 2BAT BAT1 LITHIUM ION SECONDARY BATTERY LED DRIVE Q702, 703, 716, 717 V

46、DD33_VF POWER/CHG D701 RESET SIGNAL GENERATOR IC508 SOFT START SWITCH Q510 513 VDD50_VB +5V REGULATOR IC504 VDD50_VD +3.3V REGULATOR IC512 VDD3_3_DAC 5V REGULATOR IC503 DC/DC CONVERTER IC501, Q503 VDDN50_VC +3.3V REGULATOR IC506 VDD33_VF 5V REGULATOR IC505 VDDN50_VE : iPhone/iPad/iPod : WALKMAN/Xperia : AUDIO (ANALOG) : AUDIO (DIGITAL) SIGNAL PATH (GRN) (RED) S001 GAIN HIGHNORMAL S001 GAIN HIGHLOWNORMAL F701 VDDN50_VC VDD50_VD GAIN CONTROL Q003 + (PHA-1A) (PHA-1AEU) R-ch is omitted due to same Ver. 1.1 PHA-1A/1AEU PHA-1A/1AEU 1010 For Schematic Diagrams.

展开阅读全文
相关资源
猜你喜欢
相关搜索
资源标签

当前位置:首页 > 进口随身听 > Sony

copyright@ 2008-2025 收音机爱好者资料库 版权所有
备案编号:鄂ICP备16009402-5号