《Roland_cube_30 电路图 维修原理图.pdf》由会员分享，可在线阅读，更多相关《Roland_cube_30 电路图 维修原理图.pdf（12页珍藏版）》请在收音机爱好者资料库上搜索。
1、SERVICE NOTES Issued by RJA Copyright 2002 ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION. Printed in Japan (0800) (NB)17058088E0 Jul.2002CUBE-30 TABLE OF CONTENTS SPECIFICATIONS.2 LOCATION OF CON
2、TROLS .3 LOCATION OF CONTROLS PARTS LIST.3 EXPLODED VIEW(CABNET).4 EXPLODED VIEW PARTS LIST(CABINET) .5 EXPLODED VIEW(CHASSIS).6 EXPLODED VIEW PARTS LIST(CHASSIS).7 PARTS LIST.8 CHECKING THE VERSION NUMBER.10 TEST MODE.10 CAUTIONS FOR THE REPLACEMENT OF DAMAGED POWER SUPPLY CORD.12 收音机爱好者资料库 Ra d i
3、o Fa n s .CN 2 Jul.2002 SPECIFICATIONS CUBE-30 GUITAR AMPLIFIER SPECIFICATIONS Rated Power Output 30W Nominal Input Level (1kHz) INPUT -10dBu/1Mohms AUX IN -10dBu Speaker 25cm (10inch) x1 Controls JC CLEAN Channel VOLUME Knob LEAD Channel TYPE Switch (ACOUSTIC, BLACK PANEL, BRIT COMBO, TWEED, CLASSI
4、C STACK, METAL STACK, R-FIER STACK) GAIN Knob VOLUME Knob EQUALIZER BASS Knob MIDDLE Knob TREBLE Knob EFX Knob (CHORUS, FLANGER, PHASER, TREMOLO) DELAY/REVERB Knob SELECT Switch POWER Switch Indicators CLEAN Channel LEAD Channel EFX Connectors INPUT Jack (1/4”phone type) AUX IN Jack (1/4”phone type)
5、 RECORDING OUT/HEADPHONE (Stereo 1/4”phone type) FOOT Switch Jack (TIP: SELECT, RING: EFX) (1/4”Stereo phone type) Power Supply AC117V, 230V, 240V Power Consumption 34W Dimension 385 (W) x240 (D) x380 (H) mm 15”-13/16 (W) x9”-1/2 (D) x15” (H) inches Weights 9.2kg/20lbs 5oz Accessories Owners ManualE
6、nglish:(#SD000004) Japanese:(#SD000003) Options Footswitch FS-5U (BOSS) Connection cable PCS-31 * 0dBu = 0.775Vrms 收音机爱好者资料库 Ra d i o Fa n s .CN 3 CUBE-30 LOCATION OF CONTROLS fig.panel30 LOCATION OF CONTROLS PARTS LIST all JACK NUT: SD000042JACK NUT all KNOB: SD000043KNOB 125678 710469 43 No.Part C
7、odePart NameDescriptionQty 113449146YKB21-5012 (W/SW)6.5MM JACK1 2SD000044LED GREEN1 32249752100PUSH BUTTONBLACK #5211 3SD000059SPUP128100PUSH SWITCH1 4SD000045LED RED1 5SD000061SRBV17ROTARY SWITCH1 6SD000055RK09L1120 10KB9MM ROTARY8 713449252YKB21-5006 (STEREO W/SW)6.5MM JACK1 802897801SDDJE13200 9
8、4V-0SEESAW SWITCH1 9SD000030CHASSIS1 1013449145YKB21-50106.5MM JACK2 收音机爱好者资料库 Ra d i o Fa n s .CN 4 Jul.2002 EXPLODED VIEW(CABNET) fig.explo-1 Dont keep a speaker cable from contact a Heatsink and a primary power supply unit when equipping with a chassis. c 5 f 4 3 4 4 6 7 2 e e e e d b 1 a f e g 5
9、 CUBE-30 EXPLODED VIEW PARTS LIST(CABINET) PART SCREW NoPart CodePart NameDescriptionQty 1SD000017BADGE1 2SD000034GRILL1 3SD000035HANDLE WITH ESCUTHEON1 4SD000031CORNER PROTECTOR4 5SD000066TRIM1 6SD000028CABINET ASSY1 CABINET ASSY include the following parts. SD000031 CORNER PROTECTOR SD000066 TRIM
10、7SD000033SPEAKER 3645101 NoPart CodePart NameDescriptionQty aSD000047SCREW 3X8OVALHEAD MACHINE BZC2 b40011689SPEED NUT M3F-TYPE2 cSD000048SCREW 5X35OVALHEAD MACHINE BZC2 dSD000019SCREW 4X25BINDING MACHINE BZC4 eSD000067SCREW 3X12TRUSS TAPTITE A1 BZC29 fSD000068SCREW 4X25TRUSS TAPTITE A1 BZC8 gSD0000
11、69WASHER M4 11FAIADDITIONAL PLASTIC WASHER4 6 Jul.2002 EXPLODED VIEW(CHASSIS) fig.explo-2 9 7 1 2 6 5 4 3 11 a b 10 8 i k e i n h f f m n h d d e c g j l o 7 CUBE-30 EXPLODED VIEW PARTS LIST(CHASSIS) PART * i SCREW M3X6 is not included in PCB ASSY. SCREW NoPart CodePart NameDescriptionQty 1SD000015A
12、C CORDSP-502B 240V1 1SD000014AC CORDSP-301 117V1 1SD000012AC CORDSP-023 230V1 1SD000016AC CORDSP-60 230VE1 2SD000030CHASSIS1 372360705CORD HOOK2 42249752100PUSH BUTTONBLACK #5211 5SD000043KNOB9 612369410RTAC CORD HOLDER1702B2 7SD000053 PCB SPACER* SCC-6 94V-03 8SD000036HEATSINK1 9SD000001PCB ASSY100
13、/117V1 1002897801SEESAW SWITCHSDDJE13200 94V-01 11SD000064TRANSFORMERST-11544 230V/240V1 11SD000065TRANSFORMERST-11545 100V/117V1 NoPart CodePart NameDescriptionQty a17048631VR ACCESSORY WASHER M99 b17048630VR ACCESSORY NUT M99 c40345534SCREW M4X25PAN MACHINE W/SW+PW BZC2 d40011767FLANGE HEX NUT M4F
14、E CM4 e40011756FLANGE HEX NUT M3ZC4 fSD000042JACK NUT4 gSD000018SCREW 4X12BINDING MACHINE BZC2 h40011889EXTERNAL TOOTH WASHER M4FECM3 i40017934SCREW M3X6PAN MACHINE W/SW+PW FE ZC4 j40010301SCREW M3X20BINDING MACHINE BZC2 k40012878SCREW M3X10PAN MACHINE W/SW+PW ZC2 l40012945SCREW M3X6PAN MACHINE W/SW
15、+PW BZC2 m22150518STANDOFFHEX.BOSS 5.5X15 M32 nSD000052SCREW 4X8PAN MACHINE BZC3 o40347534M4 SPRING WASHERBZC2 8 Jul.2002 PARTS LIST fig.part1e Safety Precautions The method of replacing the damaged power supply cord vary with serial numbers. Please refer to followings. 1. Up to serial No.ZP90419(10
16、0V) and NO. ZQ02579(117V,230V) and ZP91179(240V) Replace power supply cord and PS-1 BOARD when replacing the damaged power supply cord. Do not replace only power supply cord due to preventing the damage of the traces of the PS-1 BOARD by heating of the soldering iron. NOTE: Use only the power supply
17、 cord and PS-1 BOARD served by Roland Service Center Japan. Please order the components to Roland Service Center Japan. PCB ASSY (P/No.SD000001) includes the PS-1 BOARD. 2. From serial No.ZP90420(100V) and NO. ZQ02580(117V,230V) and ZP91180(240V) Please replace only the damaged power supply cord acc
18、ording to “Cautions for the replacement of damaged power supply cord.” CASINGQty SD000017BADGE 1 # SD000034GRILL 1 SD000035HANDLE WITH ESCUTHEON 1 # SD000028CABINET ASSY 1 CABINET ASSY includes the following parts. SD000031 CORNER PROTECTOR 4 # SD000066TRIM 1 CHASSIS 22360705CORD HOOK 2 # SD000030CH
19、ASSIS 1 KNOB,BUTTON 2249752100PUSH BUTTONBLACK #521 1 SD000043KNOB 9 SWITCH 02897801SDDJE13200 94V-0SEESAW SWITCHSW11 # SD000061SRBV17ROTARY SWITCHSW3 on RSWB1 SD000059SPUP128100PUSH SWITCHSW2 on CB1 JACK,EXT TERMINAL 13449252YKB21-5006 (STEREO W/SW)6.5MM JACKJK2 on MB1 13449145YKB21-50106.5MM JACKJ
20、K3 on MB, JK4 on CB2 13449146YKB21-5012 (W/SW)6.5MM JACKJK1 on CB1 SPEAKER,BUZZER # SD000033SPEAKER 364510 1 PWB ASSY # SD000001PCB ASSY100/117V 1 PCB ASSY includes the following parts SD000053PCB SPACERSCC-6 94V-0HEATSINK3 # SD000036HEATSINK 1 *PS-1 BOARD1 PCB ASSY 100/117V is exclusively for 100/1
21、17V use. For 230/240V, make the following modifications to this “Low Voltage PWB”. 1.Replace fuse to specific one. 2.Write the mark in the specification voltage(230/240V) table of PCB ASSY. See Table A. SAFETY PRECAUTIONS: The parts marked have safety-related characteristics. Use only listed parts f
22、or replacement. CONSIDERATION ON PARTS ORDRING When ordering any parts listed in the parts list, please specify the following items in the order sheet. QTYPART NUMBERDESCRIPTIONMODEL NUMBER Ex.1022575241Sharp KeyC-20/50 152247017300Knob (orange)DAC-15D Failure to completely fill the above items with
23、 correct number and description will result in delayed or even undelivered replacement. NOTE: The parts marked # are new. (initial parts) 9 CUBE-30 Table A 100 / 117V SB 1A 250V 100 / 117V SB 1A 250V 230 / 240V T500mAL 250V230 / 240V T 500mAL 250V DIODE SD000044LED GREEN D13 on CB1 SD000045LED RED D
24、14 on CB, D7 on MB1 POTENTIOMETER SD000055RK09L1120 10KB9MM ROTARYVR 1,2,3 on CB, V R4,5,6,7,8 on MB8 FUSE,FUSE HOLDER # SD0000085ST 500MA/250VFUSEFH1 on PS1B1 TRANSFORMER # SD000064ST-11544 230V/240VTRANSFORMER 1 # SD000065ST-11545 100V/117VTRANSFORMER 1 AC CORD ASSY (Installed) SD000012SP-023 230V
25、AC CORD 1 SD000014SP-301 117VAC CORD 1 SD000015SP-502B 240VAC CORD 1 SD000016SP-60 230VEAC CORD 1 SCREWS 40011756FLANGE HEX NUT M3ZCAC CORD BUSH, POWER IC4 SD000067SCREW 3X12TRUSS TAPTITE A1 BZCCORNER PROTECTOR29 SD000068SCREW 4X25TRUSS TAPTITE A1 BZCGRILL, CHASSIS8 40012878SCREW M3X10PAN MACHINE W/
26、SW+PW ZCPOWER IC2 40017934SCREW M3X6 PAN MACHINE W/SW+PW FE ZC PCB4 40012945SCREW M3X6PAN MACHINE W/SW+PW BZCSTAND OFF NUT2 40345534SCREW M4X25PAN MACHINE W/SW+PW BZCAC CORD HOOK2 SD000052SCREW 4X8PAN MACHINE BZCAC CORD GND,WIRING GND3 SD000047SCREW 3X8OVALHEAD MACHINE BZCBADGE2 SD000048SCREW 5X35OV
27、ALHEAD MACHINE BZCHANDLE2 22150518STANDOFFHEX.BOSS 5.5X15 M3PCB2 40011889EXTERNAL TOOTH WASHER M4FECMAC CORD GND,WIRING GND3 40011767FLANGE HEX NUT M4FE CMTRANSFORMER PCB WIRING4 40011689SPEED NUT M3F-TYPEBADGE2 40010189SCREW 3X8BINDING ZCAC CORD BUSH2 SD000018SCREW 4X12BINDING MACHINE BZCTRANSFORME
28、R2 SD000019SCREW 4X25BINDING MACHINE BZCSPEAKER4 SD000042JACK NUT JACK4 17048630VR ACCESSORY NUT M9 VR, ROTARY SW9 17048631VR ACCESSORY WASHER M9 VR, ROTARY SW9 SD000069WASHER M4 11FAIADDITIONAL PLASTIC WASHERGRILL4 40347534M4 SPRING WASHERBZCTRANSFORMER2 PACKING SD000046MIRAMIT SHEET 1 # SD000049PA
29、CKING BAG 1 # SD000050PACKING CASE 1 SD000051PACKING INNER 4 MISCELLANEOUS SD000058ADHESIVESC608LVZWring for primary power transformer and PS1 BOARD. 12369410RTAC CORD HOLDER1702BAC CORD2 SD000029CABLE TIE 6 ACCESSORIES (Standard) # SD000003OWNERS MANUALJAPANESE # SD000004OWNERS MANUALENGLISH PWB AS
30、SY 10 Jul.2002 CHECKING THE VERSION NUMBER 1. Connection of foot switches Connect two FS-5U foot switches to the FOOT.SW terminals with the PCS-31 foot switch cable. See “How to set the foot switch FS-5U”. polarity setting for FS-5U foot switch Set the polarity switch to the jack side. Cable of conn
31、ections for foot switch The PCS-31 connection cable for the foot switch is a conversion cable connecting a stereo plug and two standard plugs. Connect the standard plugs to the foot switches. The “white” side of the standard plug is used to change JC CLEAN and LEAD of SELECT. The “red side” of the s
32、tandard plug is used to switch EFX on and off. TIP and RING of the stereo (TRS) plugs of the PCS-31 correspond to SELECT and EFX, respectively. 2. Setting up of the panel Set the LEAD CH rotary switch to “ACOUSTIC”, and all other knobs to “0” or “off”. Undepress the SELECT button to JC CLEAN (to gre
33、en LED when the power is on). 3. How to check the version number After completing 1) and 2), turn on the power while pressing the foot switch for SELECT switching (white side). Then within four seconds, press it again twice to start the test mode. As soon as the test mode starts, all LEDs blink seve
34、ral times, then some LEDs blink to display the version number (see the following on how to display the version number). If setting up of the panel in 2) is not done correctly, the test mode cannot be started. 4. How to display the version number The version number is displayed by the blinking/off co
35、mbination of the green and red LEDs of SELECT, the red LED of EFX ON/OFF. : Blinking : Off. 5. Turn off this unit TEST MODE 1 What is needed Headphones 1 set Foot switch BOSS FS-5U (Optional) 2 units Connection cable for foot switch ROLAND PCS-31 (Optional) 1 unit 2 How to enter the test mode 1. Con
36、nection of foot switches Connect two FS-5U foot switches to the FOOT.SW terminals with the PCS-31 foot switch cable (See CHECKING THE VERSION NUMBER 1. Connection of foot switches). 2. Setting up of the panel Set the LEAD CH rotary switch to “ACOUSTIC”, and all other knobs to “0” or “off”. Undepress
37、 the SELECT button to JC CLEAN (to green LED when the power is on). 3. How to enter the test mode After completing 1) and 2), turn on the power while pressing the foot switch for SELECT switching (white side). Then within four seconds, press it again twice to start the test mode. As soon as the test
38、 mode starts, all LEDs blink several times, then some LEDs blink to display the version number (see the following on how to display the version number). Confirm here that all LEDs can be turned on to show the succeeding check results correctly. If setting up of the panel in 2) is not done correctly,
39、 the test mode cannot be started. 3 How to exit the test mode Turn off the power to exit the test mode. 4 Skipping The check mode cannot be skipped. 5 Test items 1)DSP check: (automatically judged) 2)Switch check: 3)Volume check: LEDs used for display1.001.011.021.03 . . . JC CLEAN Green LED LEAD Re
40、d LED EFX Red LED 11 CUBE-30 6 Contents of test items 1. Display the version number The version number is displayed by the blinking/off combination of the green and red LEDs of SELECT, the red LED of EFX ON/OFF. : Blinking : Off. 2. DSP check: (automatically judged) Press the foot switch once for SE
41、LECT switching (white side) during version display to turn off the LEDs and start automatic checks. The LEDs come on in the order of green, red of SELECT and red of EFX during the checks. If all the checks are completed and the results are OK, all LEDs blink. If the results are NG (no good, fail), o
42、nly the EFX LED blinks. The automatic checks take approximately 5 - 6 seconds. If the check results are OK, press the foot switch for SELECT switching (white side) to proceed to the next check. If the results are NG, the next check cannot be started. 3. Switch check: When the switch check starts, al
43、l LEDs go out. 1. SELECT switch operation check Press the SELECT button. If the check results are OK, both of the green and red LEDs of SELECT come on. If the check results are NG, none of the LEDs come on. The next check cannot be started, either. 2. Operation check for “AMP TYPE switching” of LEAD
44、 rotary switch Shift the switch slowly in the following order to check if the switch setting is read correctly. At this time, check if the green and red LEDs of SELECT come on alternately as follows. ACOUSTIC (green, red) BLACK PANEL (green) BRIT COMBO (red) TWEED (green) CLASSIC STACK (red) METAL S
45、TACK (green) R-FIER STACK (red) METAL STACK (green) CLASSIC STACK (red) TWEED (green) BRIT COMBO (red) BLACK PANEL (green) ACOUSTIC (red) If the check results are OK, both of the green and red LEDs of SELECT come on. If the check results are NG, the green and red LEDs do not come on simultaneously.
46、The next check cannot be started, either. If the switch knob is shifted too fast, the green and red LEDs blink. In this case, repeat the operation slowly to allow the switch settings to be read at all positions. 3. Jack switch (foot switch terminal EFX, RECORDING OUT/PHONES terminal) check a. Foot s
47、witch terminal EFX check Press the foot switch for EFX (red side) on/off switching to check if the green LED of SELECT comes on. Then disconnect the PCS-31 plug from the EFX terminal to check if the green LED of SELECT goes out and the red LED comes on. Then insert the PCS-31 plug again to check if the green LED of SELECT com
免费区 
