SONY MZ-N910 维修电路图.pdf

《SONY MZ-N910 维修电路图.pdf》由会员分享，可在线阅读，更多相关《SONY MZ-N910 维修电路图.pdf（65页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL MZ-N910 Ver. 1.5 2006.05 AEP Model UK Model E Model Australian Model Chinese Model Tourist Model PORTABLE MINIDISC RECORDER 9-877-146-06Sony Corporation 2006E16-1Personal Audio Division C 2006.05Published by Sony Techno Create Corporation Continued on next page US and foreign patents

2、licensed from Dolby Laboratories. Model Name Using Similar MechanismNEW Mechanism TypeMT-MZN910-181 Optical Pick-up NameABX-1R SPECIFICATIONS Audio playing system MiniDisc digital audio system Laser diode properties Material: GaAlAs Wavelength: = 790 nm Emission duration: continuous Laser output: le

3、ss than 44.6 W (This output is the value measured at a distance of 200 mm from the lens surface on the optical pick-up block with 7 mm aperture.) Recording and playback time (when using MDW-80) Maximum 160 min. in monaural Maximum 320 min. in LP4 stereo Revolutions 350 rpm to 3,600 rpm (CLV) Error c

4、orrection ACIRC (Advanced Cross Interleave Reed Solomon Code) Sampling frequency 44.1 kHz Sampling rate converter Input: 32 kHz/44.1 kHz/48 kHz Coding ATRAC (Adaptive TRansform Acoustic Coding) ATRAC3 LP2/LP4 Modulation system EFM (Eight to Fourteen Modulation) Frequency response 20 to 20,000 Hz 3 d

5、B When recording (Unit: approx.hours)(JEITA4) BatteriesSP Stereo LP2 Stereo LP4 Stereo NH-14WM nickel metal hydride rechargeable battery NH-14WM nickel metal hydride rechargeable battery NH-14WM nickel metal hydride rechargeable battery + One NH-14WM nickel metal hydride rechargeable battery + One 1

6、11620 111621LR6 (SG) Sony alkaline dry battery LR6 (SG) LR6 (SG) 293850 When playing BatteriesSP Stereo LP2 Stereo LP4 Stereo 313845 LR6 (SG) Sony alkaline dry battery 475769 8095114 Battery operation time3)Inputs1) MIC: stereo mini-jack (minimum input level 0.25 mV) Line in: stereo mini-jack for an

7、alog input (minimum input level 49 mV) optical (digital) mini-jack for optical (digital) input Outputs i/LINE OUT2): stereo mini-jack (dedicated remote control jack)/194 mV (10 k) Maximum output (DC)2) Headphones: 4 mW + 4 mW (16 )(AEP,UK models) 5 mW + 5 mW (16 )(other models) Power requirements So

8、ny AC Power Adaptor connected at the DC IN 3V jack: 120 V AC, 60 Hz (Models for USA, Canada, Mexico and Taiwan) 230 - V AC, 50/60 Hz (Models for continental Europe) 240 V AC, 50 Hz (Model for Australia) 220 V AC, 50 Hz (Model for China) 230 - V AC, 50 Hz (Models for U.K. and Hong Kong) 100 - 240 V A

9、C, 50/60 Hz (Other models) The recorder: Nickel metal hydride rechargeable battery NH-14WM, 1.2V, 1350mAh (MIN), Ni-MH LR6 (size AA) alkaline battery Battery charging stand: AC power adaptor DC 3V SILVER MODEL 收音机爱好者资料库 Ra d i o Fa n s .CN 2 MZ-N910 CAUTION Use of controls or adjustments or performa

10、nce of procedures other than those specified herein may result in hazardous ra- diation exposure. Notes on chip component replacement Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor may be dam- aged by heat. Flexible Circuit Board Repairing Keep the temp

11、erature of the soldering iron around 270 C dur- ing repairing. Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). Be careful not to apply force on the conductor when soldering or unsoldering. UNLEADED SOLDER Boards requiring use of unleaded solder are printe

12、d with the lead- free mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size) : LEAD FREE MARK Unleaded solder has the following characteristics. Unleaded solder melts at a temperature about 40

13、 C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350 C . Caution: The printed pattern (copper foil) may peel away if the heated

14、tip is applied for too long, so be careful! Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. Usable with ordinary solder It is best to use only unleaded solder but unleaded solde

15、r may also be added to ordinary solder. For use in your house: For the supplied battery charging stand, use the AC power adaptor supplied with this recorder. Do not use any other AC power adaptor since it may cause the recorder to malfunction Polarity of the plug SAFETY-RELATED COMPONENT WARNING! CO

16、MPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. Optical cable (1) CD-ROM (SonicStag

17、e Ver. 1.5) (1)* Carrying pouch/carrying case with a belt clip (1) Do not play a CD-ROM on an audio CD player. Headphones/earphones with a remote control (1) Dimensions Approx. 78.9 72.2 15.9 mm (w/h/d) (31/8 7/8 32 2 21 / in.) (excluding projecting parts and controls) Mass Approx. 93 g (3.3 oz) 1)T

18、he LINE IN (OPT) jack is used to connect either a digital (optical) cable or a line (analog) cable. 2)The i/LINE OUT jack connects either headphones/earphones or a line cable. 3)Measured in accordance with JEITA. Design and specifications are subject to change without notice. 4)Measured in accordanc

19、e with the JEITA (Japan Electronics and Information Technology Industries Association) standard. Supplied accessories AC power adaptor (1) Battery charging stand (1) NH-14WM Nickel metal hydride rechargeable battery (1) Dry battery case (1) Battery carrying case (1) 收音机爱好者资料库 Ra d i o Fa n s .CN 3 M

20、Z-N910 1.SERVICING NOTES. 4 2.GENERAL. 5 3.DISASSEMBLY 3-1. Bottom Panel Block Assy. 7 3-2. Upper Lid Block Assy . 7 3-3. LCD Module. 8 3-4. MAIN Board, Case (battery). 8 3-5. MD Mechanism Deck (MT-MZN910-181), Set Chassis. 9 3-6. Case (battery) . 9 3-7. Gear (BSA), Gear (SB) . 10 3-8. OP Service As

21、sy (ABX-1R). 10 3-9. DC Motor SSM22A (sled) (M602), DC Motor SSM18D (spindle) (M601), DC Motor Unit (over write head up/down) (M603) . 11 3-10. Holder Assy . 11 4.TEST MODE. 12 5.ELECTRICAL ADJUSTMENTS.18 6.DIAGRAMS 6-1. Block Diagram . 37 6-2. Note for Printed Wiring Board and Schematic Diagrams. 3

22、8 6-3. Printed Wiring Board MAIN Board (Side A) . 39 MAIN Board (Side B) . 40 6-4. Schematic Diagrams MAIN Board (1/4) . 41 MAIN Board (2/4) . 42 MAIN Board (3/4) . 43 MAIN Board (4/4) . 44 6-5. IC Pin Function Description . 50 7.EXPLODED VIEWS 7-1. Case Section . 56 7-2. Chassis Section. 57 7-3. MA

23、IN Board Section .58 7-4. MD Mechanism Deck Section (MT-MZN910-181) . 59 8.ELECTRICAL PARTS LIST.60 TABLE OF CONTENTS 收音机爱好者资料库 Ra d i o Fa n s .CN 4 MZ-N910 NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electro- static break-down be

24、cause of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged an

25、d should be handled with care. NOTES ON LASER DIODE EMISSION CHECK Never look into the laser diode emission from right above when checking it for adjustment. It is feared that you will lose your sight. NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK (ABX-1R) The laser diode in the optical pick-up block

26、may suffer electro- static break-down easily. When handling it, perform soldering bridge to the laser-tap on the flexible board. Also perform mea- sures against electrostatic break-down sufficiently before the op- eration. The flexible board is easily damaged and should be handled with care. SECTION

27、 1 SERVICING NOTES In performing the repair the power supplied to the set, remov- ing the MAIN board causes the set to be disabled. In such a case, perform soldering bridge to SL802 on MAIN board. laser-tap OPTICAL PICK-UP FLEXIBLE BOARD MAIN board FLEXIBLE board (over write head) Handle the FLEXIBL

28、E board (over write head) with care, as it has been soldered directly to the MAIN board. In repairing the component side of MAIN board, connect the FLEXIBLE board (over write head) and the MAIN board with the lead wires in advance. System requirements The following hardware and software are required

29、 in order to use the SonicStage software for the Net MD. This software is not supported by the following environments: Macintosh Windows XP versions other than Home Edition or Professional Windows 2000 versions other than Professional Windows 98 versions other than Second Edition Windows NT Windows

30、95 Personally constructed PCs or operating systems An environment that is an upgrade of the original manufacturer-installed Multi-boot environment Multi-monitor environment Notes We do not ensure trouble-free operation on all computers that satisfy the We do not ensure trouble-free operation of the

31、system suspend, sleep, or hibernation function on all computers. Computer IBM PC/AT or Compatible CPU: Pentium II 400 MHz or higher (Pentium III 450 MHz or higher is recommended.) Hard disk drive space1): 120 MB or more 1) Others CD-ROM drive (capable of digital playback by WDM) Sound Board Operatin

32、g System Factory installed: Windows XP Home Edition/Windows XP Professional/ Windows Millennium Edition/Windows 2000 Professional/ Windows 98 Second Edition DisplayHigh Color (16bit) or greater, 800 480 dots or more Others Internet access: for Web registration and EMD services Note on hard disk driv

33、e space 120 MB or more free space on the hard disk drive is required. If your computer does not have enough space, the software will not be properly installed. The required free space differs according to the version of your Windows OS, or the amount of audio files that you handle. USB port (support

34、s USB 2.0 Full Speed (previously USB 1.1) (800 600 dots or more is recommended) Windows Media Player (version 7.0 or higher) installed for playing WMA files RAM: 64 MB or higher (128 MB or higher is recommended) operating system system requirements. MAIN BOARD (SIDE A) SL802 Replacement of SN761058A

35、ZQLR (IC501), CXD2680-205GA (IC801) used in this set requires a special tool The shipment data will be cleared when the NV is reset. There- fore, change the NV adjusted values following the Change of NV Adjusted Values immediately after the NV was reset. (See page 18) This set requires the patch dat

36、a in the nonvolatile memory (IC851) to be rewritten using the application, when the MAIN board was replaced. (See page 29) 5 MZ-N910 SECTION 2 GENERAL This section is extracted from instruction manual. Looking at controls The recorder A END SEARCH button B T MARK button C Battery compartment D Displ

37、ay window E GROUP button F x CHG button G HOLD switch Slide the switch in the direction of the arrow to disable the buttons on the recorder. To prevent the buttons from being accidentally operated when you carry the recorder, use this function. H Terminals for attaching a battery charging stand I Te

38、rminals for attaching a dry battery case J DC IN 3V jack K X button L 5-way control key The N and VOL + button has a tactile dot. M OPEN switch qf 1 4 5 8 6 7 9 q; qa qd qs qh qg qj qk w; ql 2 3 OperationFunction Press N*play Press . rewind Press fast forward Press VOL +*, volume N Jog dial (MENU/EN

39、TER) O Handstrap hole Use the hole to attach your own strap. P Dedicated USB cable connecting jack Q LINE IN (OPT) jack R MIC (PLUG IN POWER) jack There is a tactile dot beside the MIC (PLUG IN POWER) jack. S REC (record) switch T i (headphones/earphones)/LINE OUT jack The display window of the reco

40、rder A Play mode indication Shows the play mode (shuffle play, program play, repeat play, etc.) of the MD. B Group indication C Character information display Displays the disc and track names, date, error messages, track numbers, etc. D REC indication Lights up while recording. When flashing, the re

41、corder is in record standby mode. E SYNC (synchro-recording) indication F Bookmark indication Lights up when playing a bookmarked track. G Level meter H Battery indication Shows the approximate remaining battery condition. I LP2, LP4, MONO (monaural) indication J Melody timer indication K Disc indic

42、ation Shows that the disc is rotating for recording or playing. Turn to select Push to enter 1235 890qa 46 7 The headphones/earphones with a remote control A Volume control (VOL+, ) Turn to adjust the volume. B x (stop) button C Jog lever (NX/ENT, ., ) NX/ENT (to press): play, pause, enter .(to slid

43、e towards): REW (to slide towards): FF D Display window E(group) +, F Clip G HOLD switch Slide the switch in the direction of the arrow (a yellow mark appears) to disable the buttons on the remote control. To prevent the buttons from being accidentally operated when you carry the recorder, use this

44、function. H DISPLAY button I P MODE/ button J SOUND button B C D E A F G H I J The display window of the remote control A Disc indication B Track number display C Character information display D Play mode indication E SOUND indication F Battery level indication G Group indication H Bookmark indicati

45、on I Melody timer indication 1 2 Using the clip for the remote control It may be hard for you to read the indications in the display if the remote control is attached upside down with the clip in its current position. In this case, attach the clip in the opposite direction as shown below. 1 Remove the clip. 2 Attach the clip in the opposite direction. FGHI BACDE 6 MZ-N910 SECTION 3 DISASSEMBLY Note: This set can be disassemble according to the