Aiwa Cd Stereo Cassette Receiver Z-Hk550 Parts & Service 电路图.pdf

《Aiwa Cd Stereo Cassette Receiver Z-Hk550 Parts & Service 电路图.pdf》由会员分享，可在线阅读，更多相关《Aiwa Cd Stereo Cassette Receiver Z-Hk550 Parts & Service 电路图.pdf（39页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL DATA COMPACT DISC STEREO CASSETTE RECEIVER BASIC TAPE MECHANISM : ZZM-3 PR1NM BASIC CD MECHANISM : 6ZG-1 VZRDM Z-HK550HR S/M Code No. 09-005-428-5R1 REVISION This Service Manual is the Revision Publishing and replaces Simple Manual Z-HK550 (HR), (S/M Code No. 09-005-428-5T1). If requi

2、ring information about the CD mechanism, see Service Manual of 6ZG-1, (S/M Code No. 09-001-338-7N4). ZHK550 SPEAKERSYSTEM CD CASSEIVER SXWZHK550CXZHK550 REMOTE CONTROLLER RCZAS07 RadioFans.CN 收音机爱 好者资料库 2 SPECIFICATIONS Tuning range87.5 MHz to 108 MHz Usable sensitivity (IHF)13.2 dBf Antenna termina

3、ls75 ohms (unbalanced) Tuning range531 kHz to 1602 kHz (9 kHz step) 530 kHz to 1710 kHz (10 kHz step) Usable sensitivity350 V/m AntennaLoop antenna Mid-high frequency amplifier Power outputRated: 20 W + 20 W (8 ohms, T.H.D. 1 %, 1 kHz) Reference: 25 W + 25 W (8 ohms, T.H.D. 10 %, 1 kHz) Total harmon

4、ic distortion 0.15 % (15 W, 1 kHz, 8 ohms) Low frequency amplifier Power outputRated: 60 W + 60 W (6 ohms, T.H.D. 1 %, 75 Hz) Reference : 75 W + 75 W (6 ohms, T.H.D. 10 %, 75 Hz) Total harmonic distortion 0.15 % (45 W, 75 Hz, 6 ohms) InputsVIDEO/AUX/PHONO IN: 300 mV MIC1, MIC2: 1.4 mV (20 kohms) Out

5、putsVIDEO OUT: 1.0 VP-P (75 ohms) CD DIGITAL OUT (OPTICAL) SPEAKERS HIGH FREQ: accept speakers of 8 ohms or more SPEAKERS LOW FREQ: accept speakers of 6 ohms or more PHONES (stereo jack): accepts headphones of 32 ohms or more Track format4 tracks, 2 channels stereo Frequency response50 Hz 12500 Hz R

6、ecording systemAC bias HeadsDeck 1 : Playback head x 1 Deck 2 : Recording/Playback head x 1, erase head x 1 LaserSemiconductor laser ( =780 nm) D-A converter1 bit dual Signal-to-noise ratio85 dB (1 kHz, 0 dB) Harmonic distortion0.05 % (1 kHz, 0 dB) Wow and flutterUnmeasurable Video SignalNTSC / PAL

7、color format (selectable) Video DataMPEG1 Audio DataMPEG1, LAYER 2 Cabinet type3 way, built-in subwoofer SpeakersSubwoofer: 220 mm (83/4 in.) cone type Full range: 120 mm (43/4 in.) cone type Super tweeter: 20 mm (13/16 in.) ceramic type Impedance6 ohms/8 ohms Output sound pressure level 89 dB/W/m D

8、imensions (W x H x D)260 x 444 x 296 mm (101/4 x 171/2 x 113/4 in.) Weight7.3 kg (16 lbs. 2 oz.) Power requirements120 V/220 - 230 V/240 V AC switchable 50/60 Hz Power consumption155 W Dimensions of main unit360 x 395.3 x 402.3 mm (W x H x D)(141/4 x 155/8 x 157/8 in.) Weight of main unit12.5 kg (27

9、 lbs. 9 oz) Design and specifications are subject to change without notice. The word BBEand the BBE symbol are trademarks of BBE Sound, Inc. Under license from BBE Sound,Inc. RadioFans.CN 收音机爱 好者资料库 3 CLASS 1LASER PRODUCT KLASSE 1LASER PRODUKT LUOKAN 1LASER LAITE KLASS 1LASER APPARAT This set employ

10、s laser. Therefore, be sure to follow carefully the instructions below when servicing. WARNING! WHEN SERVICING, DO NOT APPROACH THE LASER EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE FROM A DISTANCE OF MORE THAN 30cm FROM THE SURFACE OF TH

11、E OBJEC- TIVE LENS ON THE OPTICAL PICK-UP BLOCK. sCaution: Invisible laser radiation when open and interlocks defeated avoid exposure to beam. sAdvarsel: Usynlig laserstling ved bning, nr sikkerhedsafbrydere er ude af funktion. Undg udsttelse for strling. VAROITUS! Laiteen Kyttminen muulla kuin tss

12、kyttohjeessa mainitulla tavalla saataa altistaa kyt-tjn turvallisuusluokan 1 ylittvlle nkymttmlle lasersteilylle. VARNING! Om apparaten anvnds p annat stt n vad som specificeras i denna bruksanvising, kan anvndaren utsttas fr osynling laserstrlning, som verskrider grnsen fr laserklass 1. PROTECTION

13、OF EYES FROM LASER BEAM DURING SERVICING CAUTION Use of controls or adjustments or performance of proce- dures other than those specified herin may result in hazardous radiation exposure. ATTENTION Lutillisation de commandes, rglages ou procdures autres que ceux spcifis peut entraner une dangereuse

14、exposition aux radiations. ADVARSEL Usynlig laserstling ved bning, nr sikkerhedsafbrydereer ude af funktion. Undg udsttelse for strling. This Compact Disc player is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label is located on the rear exterior. Precaution to replace Optical b

15、lock (KSS-213F) Body or clothes electrostatic potential could ruin laser diode in the optical block. Be sure ground body and workbench, and use care the clothes do not touch the diode. 1) After the connection, remove solder shown in right figure. PICK-UP Assy P.C.B Solder RadioFans.CN 收音机爱 好者资料库 4 N

16、OTE ON BEFORE STARTING REPAIR Charging voltage (V)Discharging Rated power (W)Parts number (C101, 102)resistor () 25-48100387-A00-247-090 49-140220587-A00-232-090 Note: The reference numbers (C101, C102) of the electrolytic capacitors can change depending on the models. Be sure to check the reference

17、 numbers of the charging capacitors on schematic diagram before starting the discharging work. 2. Check items before exchanging the MICROCOMPUTER Be sure to check the following items before exchanging the MICROCOMPUTER. Exchange the MICROCOMPUTER after confirming that the MICROCOMPUTER is surely def

18、ective. 2-1. Regarding the HOLD terminal of the MICROCOMPUTER When the HOLD terminal (INPUT) of the MICROCOMPUTER is “H”, the MICROCOMPUTER is judged to be operating correctly. When this terminal is “L”, the main power cannot be turned on. Therefore, be sure to check the terminal voltage of the HOLD

19、 terminal before exchange. When the MICROCOMPUTER is not defective, the HOLD terminal can also go “L” when the POWER AMPLIFIER has any abnormalities that triggers the abnormality detection circuit on the MAIN C. B. that sets the HOLD terminal to “L”. Good or no good judgement of the MICROCOMPUTER 11

20、111Turn on the AC main power. 22222Confirm that the main power is turned on and the HOLD terminal of the MICROCOMPUTER keeps the “H” level or not. 33333When the HOLD terminal is “L” level, the abnormality detection circuit is judged to be working correctly and the MICROCOMPUTER is judged to be good.

21、 1. Forced discharge of electrolytic capacitor of power supply block When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across the electrolytic capacitors (C101, 102) even though AC power cord is removed. If repair is

22、 attempted in this condition, secondary defect can occur. In order to prevent the secondary trouble, perform the following measures before starting repair work. Discharge procedure 11111Remove the AC power cord. 22222Connect a discharging resistor at an end of lead wire that has clips at both ends.

23、Connect the other end of the lead wire to metal chassis. 33333Contact the other end of the discharging resistor to the positive (+) side (+VH) of C101. (For two seconds) 44444Contact the same end of the discharging resistor as step 33333 to the negative (-) side (-VH) of C102 in the same way. (For t

24、wo seconds) 55555Check that voltage across C101 and C102 has decreased to 1 V or less using a multimeter or an oscilloscope. Select a discharging resistor referring to the following table.Fig-1 MAIN C.B D101 C101C102 22 34 5 In such a case, check also if the POWER AMPLIFIER circuit or power supply c

25、ircuit has any abnormalities or not. 2-2. Regarding reset There are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC power cord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed. When the above described phe

26、nomenon occurs, it can lead to wrong judgement as if the MICROCOMPUTER is defective and to exchange the MICROCOMPUTER. In such a case, perform the forced-reset by the following procedure and check good or no good of the MICROCOMPUTER. 11111Remove the AC power cord. 22222Short both ends of the electr

27、olytic capacitor C113 that is connected to VDD of the MICROCOMPUTER with tweezers. 33333Connect the AC power cord again. If the MICROCOMPUTER returns to the normal operation, the MICROCOMPUTER is good. Note: The reference number or MICROCOMPUTER pin number of transistor (Q110) and electrolytic capac

28、itor (C113) can change depending on the models. Be sure to check the reference numbers on schematic diagram before starting the discharging work. 2-3. Confirmation of soldering state of MICROCOMPUTER Check the soldering state of the MICROCOMPUTER in addition to the above described procedures. Be sur

29、e to exchange the MICROCOMPUTER after surely confirming that the trouble is not caused by poor soldering but the MICROCOMPUTER itself. Fig-2-2 MICRO- COMPUTER MICROCOMPUTER FRONT C.B FRONT C.B VSS VDD C113 * % C113 18 15 Short with tweezers. 6 ELECTRICAL MAIN PARTS LIST DESCRIPTIONREF. NO.KANRI NO.

30、PART NO.DESCRIPTIONREF. NO.KANRI NO. PART NO. IC 8A-MG5-656-010 C-IC,LC876580W-5R45 87-A21-417-010 IC,STK490-340 87-A21-396-010 IC,STK490-040 87-A21-021-040 C-IC,BU2099FV 87-A20-783-040 C-IC,BA7762AFS 87-A21-577-040 C-IC,M61506FP 87-A21-482-010 IC,RPM6938-H4 87-A21-018-040 C-IC,M65849BFP631D 87-A21-

31、452-030 C-IC,BD3876KS2 87-A21-560-010 IC,LA1844L-A 87-070-127-110 IC,LC72131 D 87-A20-561-040 C-IC,M65847AFP 87-A21-269-010 IC,EW732 TRANSISTOR 87-026-609-080 TR,KTA1266GR 87-026-610-080 TR,KTC3198GR 87-A30-076-080 C-TR,2SC3052F 87-A30-075-080 C-TR,2SA1235F 87-A30-318-080 TR,CSA952K 89-213-702-010 T

32、R,2SB1370E 87-A30-257-080 C-TR,2SD1306E 87-A30-107-070 C-TR,CMBT5401 87-026-245-080 TR,DTC114ES 87-A30-198-080 TR,KTC3199GR 87-A30-484-080 C-TR,KRA 102S 87-A30-269-040 C-FET,2SJ461-T1 87-A30-087-080 C-FET,2SK2158 87-A30-468-080 C-TR,KRC 102S-RTK 87-A30-107-080 C-TR,CMBT5401 87-A30-329-080 TR,CD1585B

33、C 87-A30-063-080 C-TR,KRA 104S 87-A30-074-080 C-TR,RT1P 141C 89-327-143-080 TR,2SC2714O(0.1W) 87-A30-489-080 C-TR,KRA107S 87-A30-234-080 TR,CSC4115BC DIODE 87-020-465-080 DIODE,1SS133 (110MA) 87-A40-673-090 DIODE,D10XB20 87-A40-553-080 DIODE,1N4003 LES 87-A40-780-080 ZENER,UZ33BSD 87-A40-764-080 ZEN

34、ER,UZ10BSC 87-A40-313-080 C-DIODE,MC 2840 87-A40-270-080 C-DIODE,MC2838 87-A40-269-080 C-DIODE,MC2836 87-A40-768-080 ZENER,UZ 16BSA 87-017-447-010 DIODE,GBU4DL 87-017-154-080 ZENER,HZS6C3L 87-020-331-080 CHIP-DIODE,DAN202K 87-017-654-060 DIODE,GBU6J 87-A40-751-080 ZENER,UZ6.2BSB 87-A40-747-080 ZENER

35、,UZ5.1BSB 87-A40-438-080 ZENER,MTZJ4.7A 87-017-149-080 ZENER,HZS6A2L MAIN C.B C3 87-A10-712-080 C-CAP,S 0.22-50 F C4 87-A10-712-080 C-CAP,S 0.22-50 F C21 87-016-035-090 CAP, E 6800-35 VR C22 87-016-035-090 CAP, E 6800-35 VR C25 87-016-300-080 CAP, ELECT 22-100 C26 87-016-300-080 CAP, ELECT 22-100 C2

36、7 87-016-300-080 CAP, ELECT 22-100 C28 87-016-300-080 CAP, ELECT 22-100 C31 87-010-263-080 CAP, ELECT 100-10V C32 87-010-197-080 CAP, CHIP 0.01-25 C34 87-010-247-080 CAP, ELECT 100-50V C35 87-010-406-080 CAP, ELECT 22-50V C36 87-010-381-080 CAP, ELECT 330-16V C38 87-010-394-080 CAP, ELECT 220-35V C3

37、9 87-010-394-080 CAP, ELECT 220-35V C40 87-010-197-080 CAP, CHIP 0.01-25 C60 87-010-403-080 CAP, ELECT 3.3-50V C61 87-010-260-080 CAP, ELECT 47-25V C104 87-010-196-080 CHIP CAPACITOR,0.1-25 C105 87-010-196-080 CHIP CAPACITOR,0.1-25 C111 87-010-401-080 CAP, ELECT 1-50 M C112 87-010-401-080 CAP, ELECT

38、 1-50 M C113 87-010-545-080 CAP, ELECT 0.22-50V C114 87-010-545-080 CAP, ELECT 0.22-50V C115 87-010-546-080 CAP, ELECT 0.33-50V C116 87-010-546-080 CAP, ELECT 0.33-50V C117 87-010-196-080 CHIP CAPACITOR,0.1-25 C121 87-010-404-080 CAP, ELECT 4.7-50V C122 87-010-404-080 CAP, ELECT 4.7-50V C160 87-010-

39、196-080 CHIP CAPACITOR,0.1-25 C171 87-012-368-080 C-CAP,S 0.1-50 F C172 87-012-368-080 C-CAP,S 0.1-50 F C173 87-012-368-080 C-CAP,S 0.1-50 F C174 87-012-368-080 C-CAP,S 0.1-50 F C301 87-010-318-080 C-CAP,S 47P-50 CH C302 87-010-318-080 C-CAP,S 47P-50 CH C303 87-012-157-080 C-CAP,S 330P-50 CH C304 87

40、-012-157-080 C-CAP,S 330P-50 CH C305 87-012-157-080 C-CAP,S 330P-50 CH C306 87-012-157-080 C-CAP,S 330P-50 CH C307 87-010-196-080 CHIP CAPACITOR,0.1-25 C309 87-010-196-080 CHIP CAPACITOR,0.1-25 C310 87-010-196-080 CHIP CAPACITOR,0.1-25 C311 87-010-198-080 CAP, CHIP 0.022-25 C312 87-010-198-080 CAP,

41、CHIP 0.022-25 C313 87-010-179-080 CHIP CAP 1200P-50 C314 87-010-179-080 CHIP CAP 1200P-50 C315 87-010-178-080 CHIP CAP 1000P-50 C316 87-010-178-080 CHIP CAP 1000P-50 C321 87-012-142-080 CAP, S 0.33-16 C322 87-012-142-080 CAP, S 0.33-16 C324 87-010-260-080 CAP, ELECT 47-25V C325 87-010-370-080 CAP,E

42、330-6.3 SME C327 87-010-404-080 CAP, ELECT 4.7-50V C328 87-010-404-080 CAP, ELECT 4.7-50V C332 87-010-196-080 CHIP CAPACITOR,0.1-25 C335 87-010-401-080 CAP, ELECT 1-50V C336 87-010-401-080 CAP, ELECT 1-50V C337 87-010-196-080 CHIP CAPACITOR,0.1-25 C339 87-010-196-080 CHIP CAPACITOR,0.1-25 C340 87-01

43、0-196-080 CHIP CAPACITOR,0.1-25 C351 87-012-140-080 CAP 470P-50 C352 87-012-140-080 CAP 470P-50 C354 87-010-175-080 CAP 560P-50 C355 87-010-178-080 C-CAP,S 1000P-50 KB C356 87-010-260-080 CAP, ELECT 47-25V C357 87-010-197-080 CAP, CHIP 0.01-25 KB C358 87-010-183-080 C-CAP,S 2700P-50 B C359 87-010-18

44、3-080 C-CAP,S 2700P-50 B C360 87-010-183-080 C-CAP,S 2700P-50 B C370 87-010-196-080 CHIP CAPACITOR,0.1-25 C373 87-A11-177-080 C-CAP,S 0.15-16 K B C374 87-A11-177-080 C-CAP,S 0.15-16 K B C378 87-010-196-080 CHIP CAPACITOR,0.1-25 ZF C379 87-010-406-080 CAP, ELECT 22-50 C380 87-010-406-080 CAP, ELECT 2

45、2-50 C386 87-010-196-080 CHIP CAPACITOR,0.1-25 ZF C388 87-012-156-080 C-CAP,S 220P-50 J CH 7 DESCRIPTIONREF. NO.KANRI NO. PART NO.DESCRIPTIONREF. NO.KANRI NO. PART NO. C391 87-010-319-080 C-CAP,S 56P-50 J CH C392 87-010-319-080 C-CAP,S 56P-50 J CH C393 87-010-319-080 C-CAP,S 56P-50 J CH C394 87-010-

46、319-080 C-CAP,S 56P-50 J CH C501 87-010-263-080 CAP, ELECT 100-10V C502 87-010-196-080 CHIP CAPACITOR,0.1-25 C503 87-016-460-080 C-CAP,S 0.22-16 K B C504 87-016-460-080 C-CAP,S 0.22-16 K B C505 87-016-460-080 C-CAP,S 0.22-16 K B C506 87-010-184-080 CHIP CAPACITOR 3300P-50 C507 87-010-177-080 C-CAP,S

47、 820P-50 SL C508 87-016-669-080 C-CAP,S 0.1-25 K B C509 87-016-669-080 C-CAP,S 0.1-25 K B C510 87-010-184-080 CHIP CAPACITOR 3300P-50 C511 87-010-177-080 C-CAP,S 820P-50 SL C512 87-016-460-080 C-CAP,S 0.22-16 K B C513 87-010-544-080 CAP, ELECT 0.1-50V C514 87-010-374-080 CAP, ELECT 47-10V C515 87-010-401-080 CAP, ELECT 1-50 M C516 87-010-401-080 CAP, ELECT 1-50 M C517 87-010-183-080 C-CAP,S 2700P-50 B C518 87-010-183-080 C-CAP,S 2700P-50 B C531 87-010-405-080 CAP, ELECT 10-50 M C532 87-010-196-080 CHIP CAPACITOR,0.1-2