Aiwa Cd Stereo Cassette Receiver Nsx-Sz60 Parts & Service 电路图.pdf

《Aiwa Cd Stereo Cassette Receiver Nsx-Sz60 Parts & Service 电路图.pdf》由会员分享，可在线阅读，更多相关《Aiwa Cd Stereo Cassette Receiver Nsx-Sz60 Parts & Service 电路图.pdf（32页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL DATA COMPACT DISC STEREO CASSETTE RECEIVER NSX-SZ60EZ S/M Code No. 09-007-432-9R1 REVISION BASIC TAPE MECHANISM: 6ZM-3 YPR2N BASIC CD MECHANISM: AZG-1 YZA3RDM This Service Manual is the “Revision Publishing” and replaces “Simple Manual” NSX-SZ60, (S/M Code No. 09-004-432-9T1). If requ

2、iring information about the CD mechanisim, see Service Manual of AZG-1 (S/M Code No. 09-001-335-3NC). CD-CASSEIVER CX-NSZ60 SPEAKER SX-WNSZ71 SYSTEM NSX-SZ60 REMOTE CONTROLLER RC-ZAS01 RadioFans.CN 收音机爱 好者资料库 SPECIFICATIONS Tuning range87.5 MHz to 108 MHz Usable sensitivity(IHF)13.2 dBf Antenna term

3、inals75 ohms (unbalanced) Tuning range531 kHz to 1602 kHz (9 kHz step) 530 kHz to 1710 kHz (10 kHz step) Usable sensitivity350 uV/m AntennaLoop antenna Tuning range144 kHz to 290 kHz Usable sensitivity1400 uV/m AntennaLoop antenna Mid-high frequency amplifier Power outputRated: 20 W + 20 W (8 ohms,

4、T.H.D. 1 %, 1 kHz/DIN 45500) Reference: 25 W + 25 W (8 ohms, T.H.D. 10 %, 1 kHz/DIN 45324) DIN MUSIC POWER: 40 W + 40 W Total harmonic distortion 0.1 % (10 W, 1 kHz, 8 ohms, DIN AUDIO) Low frequency amplifier Power outputRated: 60 W + 60 W (6 ohms, T.H.D. 1 %, 130 Hz/DIN 45500) Reference: 75 W + 75

5、W (6 ohms, T.H.D. 10 %,130 Hz/DIN 45324) DIN MUSIC POWER: 130 W + 130 W Total harmonic distortion 0.1 % (35 W,130 Hz,6 ohms, DIN AUDIO) InputsVIDEO/AUX : 500 mV OutputsSPEAKERS HIGH FREQ : accept speakers of 8 ohms or more SPEAKERS LOW FREQ : accept speakers of 6 ohms or more SURROUND SPEAKERS : acc

6、ept speakers of 8 to 16 ohms LINE OUT: 210 mV PHONES (stereo jack) : accepts headphones of 32 ohms or more Track format4 tracks, 2 channels stereo Frequency response50 Hz 15000 Hz Recording systemAC bias HeadsDeck 1: Playback head x 1 Deck 2: Recording/Playback head x 1, erase head x 1 LaserSemicond

7、uctor laser ( =780 nm) D-A converter1 bit dual Signal-to-noise ratio85 dB (1 kHz, 0 dB) Harmonic distortion0.05 % (1 kHz, 0 dB) Wow and flutterUnmeasurable Speaker system3 way, Built-in subwoofer(magnetic shielded type Speaker unitsSubwoofer : 160 mm cone type Full range: 100 mm cone type Super Twee

8、ter : 20 mm ceramic type Impedance6 ohms / 8 ohms Sensitivity87 dB/W/m Dimensions (W x H x D)240 x 324 x 281 mm Weight5.2 kg Power requirements230 V AC, 50 Hz Power consumption150W Power consumption inIf the power-economizing mode is standby modeECO OFF: 20 W If the power-economizing mode is ECO ON

9、or ECO AUTO: 0.9 W Dimensions (W x H x D)260 x 330 x 345 mm Weight8.5 kg Design and specifications are subject to change without notice. The word BBEand the BBE symbol are trademarks of BBE Sound, Inc. Under license from BBE Sound,Inc. 2 ACCESSORIES / PACKAGE LIST KANRI NO. REF. NO.DESCRIPTIONPART N

10、O. 1 8A-NFH-906-010 IB,EZ(9L)E 2 87-006-225-010 AM LOOP ANT NC2 3 87-A90-118-010 ANT,WIRE FM (Z) 4 8Z-NF8-702-010 RC UNIT,RC-ZAS01 RadioFans.CN 收音机爱 好者资料库 3 CLASS 1LASER PRODUCT KLASSE 1LASER PRODUKT LUOKAN 1LASER LAITE KLASS 1LASER APPARAT This set employs laser. Therefore, be sure to follow carefu

11、lly the instructions below when servicing. WARNING! WHEN SERVICING, DO NOT APPROACH THE LASER EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE FROM A DISTANCE OF MORE THAN 30cm FROM THE SURFACE OF THE OBJEC- TIVE LENS ON THE OPTICAL PICK-UP BL

12、OCK. sCaution: Invisible laser radiation when open and interlocks defeated avoid exposure to beam. sAdvarsel: Usynlig laserstling ved bning, nr sikkerhedsafbrydere er ude af funktion. Undg udsttelse for strling. VAROITUS! Laiteen Kyttminen muulla kuin tss kyttohjeessa mainitulla tavalla saataa altis

13、taa kyt-tjn turvallisuusluokan 1 ylittvlle nkymttmlle lasersteilylle. VARNING! Om apparaten anvnds p annat stt n vad som specificeras i denna bruksanvising, kan anvndaren utsttas fr osynling laserstrlning, som verskrider grnsen fr laserklass 1. PROTECTION OF EYES FROM LASER BEAM DURING SERVICING CAU

14、TION Use of controls or adjustments or performance of proce- dures other than those specified herin may result in hazardous radiation exposure. ATTENTION Lutillisation de commandes, rglages ou procdures autres que ceux spcifis peut entraner une dangereuse exposition aux radiations. ADVARSEL Usynlig

15、laserstling ved bning, nr sikkerhedsafbrydereer ude af funktion. Undg udsttelse for strling. This Compact Disc player is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label is located on the rear exterior. Precaution to replace Optical block (KSS-213F) Body or clothes electrostati

16、c potential could ruin laser diode in the optical block. Be sure ground body and workbench, and use care the clothes do not touch the diode. 1) After the connection, remove solder shown in right figure. PICK-UP Assy P.C.B Solder RadioFans.CN 收音机爱 好者资料库 NOTE ON BEFORE STARTING REPAIR Charging voltage

17、 (V)Discharging Rated power (W)Parts number (C101, 102)resistor () 25-48100387-A00-247-090 49-140220587-A00-232-090 Note: The reference numbers (C101, C102) of the electrolytic capacitors can change depending on the models. Be sure to check the reference numbers of the charging capacitors on schemat

18、ic diagram before starting the discharging work. 2. Check items before exchanging the MICROCOMPUTER Be sure to check the following items before exchanging the MICROCOMPUTER. Exchange the MICROCOMPUTER after confirming that the MICROCOMPUTER is surely defective. 2-1. Regarding the HOLD terminal of th

19、e MICROCOMPUTER When the HOLD terminal (INPUT) of the MICROCOMPUTER is “H”, the MICROCOMPUTER is judged to be operating correctly. When this terminal is “L”, the main power cannot be turned on. Therefore, be sure to check the terminal voltage of the HOLD terminal before exchange. When the MICROCOMPU

20、TER is not defective, the HOLD terminal can also go “L” when the POWER AMPLIFIER has any abnormalities that triggers the abnormality detection circuit on the MAIN C. B. that sets the HOLD terminal to “L”. Good or no good judgement of the MICROCOMPUTER 11111Turn on the AC main power. 22222Confirm tha

21、t the main power is turned on and the HOLD terminal of the MICROCOMPUTER keeps the “H” level or not. 33333When the HOLD terminal is “L” level, the abnormality detection circuit is judged to be working correctly and the MICROCOMPUTER is judged to be good. 1. Forced discharge of electrolytic capacitor

22、 of power supply block When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across the electrolytic capacitors (C101, 102) even though AC power cord is removed. If repair is attempted in this condition, secondary defect

23、 can occur. In order to prevent the secondary trouble, perform the following measures before starting repair work. Discharge procedure 11111Remove the AC power cord. 22222Connect a discharging resistor at an end of lead wire that has clips at both ends. Connect the other end of the lead wire to meta

24、l chassis. 33333Contact the other end of the discharging resistor to the positive (+) side (+VH) of C101. (For two seconds) 44444Contact the same end of the discharging resistor as step 33333 to the negative (-) side (-VH) of C102 in the same way. (For two seconds) 55555Check that voltage across C10

25、1 and C102 has decreased to 1 V or less using a multimeter or an oscilloscope. Select a discharging resistor referring to the following table.Fig-1 MAIN C.B D101 C101C102 22 34 4 In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not. 2-2. Rega

26、rding reset There are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC power cord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed. When the above described phenomenon occurs, it can lead to wrong judgement

27、 as if the MICROCOMPUTER is defective and to exchange the MICROCOMPUTER. In such a case, perform the forced-reset by the following procedure and check good or no good of the MICROCOMPUTER. 11111Remove the AC power cord. 22222Short both ends of the electrolytic capacitor C113 that is connected to VDD

28、 of the MICROCOMPUTER with tweezers. 33333Connect the AC power cord again. If the MICROCOMPUTER returns to the normal operation, the MICROCOMPUTER is good. Note: The reference number or MICROCOMPUTER pin number of transistor (Q110) and electrolytic capacitor (C113) can change depending on the models

29、. Be sure to check the reference numbers on schematic diagram before starting the discharging work. 2-3. Confirmation of soldering state of MICROCOMPUTER Check the soldering state of the MICROCOMPUTER in addition to the above described procedures. Be sure to exchange the MICROCOMPUTER after surely c

30、onfirming that the trouble is not caused by poor soldering but the MICROCOMPUTER itself. Fig-2-2 MICRO- COMPUTER MICROCOMPUTER FRONT C.B FRONT C.B VSS VDD C113 * % C113 18 15 Short with tweezers. 5 KANRI NO. REF. NO.DESCRIPTIONPART NO.KANRI NO. REF. NO.DESCRIPTIONPART NO. 6 ELETRICAL MAIN PARTS LIST

31、 IC 87-020-454-010 IC,DN6851 87-A21-417-010 IC,STK490-310 8A-NF8-611-110 C-IC,LC866560W-5P41 87-A21-396-010 IC,STK490-040 87-A21-482-010 IC,RPM6938-H4 87-A21-419-040 C-IC,NJM14558MD-TE2 87-A21-023-040 C-IC,BA3835F 87-070-289-040 C-IC,BU2092F 87-A21-401-040 C-IC,M61503FP 87-A21-415-010 IC,LA1843 87-A

32、20-440-040 C-IC,BU1920FS 87-070-127-110 IC,LC72131 D TRANSISTOR 87-026-609-080 TR,KTA1266GR 89-213-702-010 TR,2SB1370 (1.8W) 87-026-610-080 TR,KTC3198GR 87-A30-076-080 C-TR,2SC3052F 87-A30-075-080 C-TR,2SA1235F 87-026-245-080 TR,DTC114ES 87-A30-198-080 TR,KTC3199GR 87-026-463-080 TR,2SA933SRS 87-A30

33、-107-070 C-TR,CMBT5401 87-A30-106-040 C-TR,CMBT5551 87-A30-087-080 C-FET,2SK2158 87-A30-074-080 C-TR,RT1P 141C 87-A30-091-080 FET,2SJ460 87-A30-318-080 TR,CSA952K 87-A30-090-080 FET,2SK2541 87-A30-329-080 TR,CD1585BC 87-A30-104-080 C-TR,RT1N 441C 87-A30-073-080 C-TR,RT1N 141C 89-333-317-880 TR,2SC33

34、31 (0.5W) 87-A30-269-040 C-FET,2SJ461-T1 89-327-143-080 TR,2SC2714 (0.1W) 87-A30-489-080 C-TR,KRA107S 87-A30-086-070 C-TR,CSD1306E 87-A30-484-080 C-TR,KRA102S 89-503-602-080 C-FET,2SK360E 87-A30-234-080 TR,CSC4115BC DIODE 87-A40-393-090 DIODE,1N5402GW(F20) 87-020-465-080 DIODE,1SS133 87-A40-547-090

35、DIODE,D5SBA20 87-A40-455-080 DIODE,RL203 GW 87-A40-553-080 DIODE,1N4003 LES 87-A40-776-080 ZENER,UZ27BSD 87-A40-764-080 ZENER,UZ10BSC 87-A40-313-080 C-DIODE,MC 2840 87-A40-270-080 C-DIODE,MC2838 87-A40-269-080 C-DIODE,MC2836 87-A40-768-080 ZENER,UZ16BSA 87-A40-802-080 ZENER,UZ5.1BSC 87-A40-739-080 Z

36、ENER,UZ2.7BSA 87-017-149-080 ZENER,HZS6A2L MAIN C.B C3 87-012-368-080 C-CAP,S 0.1-50 F C4 87-012-368-080 C-CAP,S 0.1-50 F C5 87-012-368-080 C-CAP,S 0.1-50 F C6 87-012-368-080 C-CAP,S 0.1-50 F C9 87-012-368-080 C-CAP,S 0.1-50 F C10 87-012-368-080 C-CAP,S 0.1-50 F C11 87-012-368-080 C-CAP,S 0.1-50 F C

37、12 87-012-368-080 C-CAP,S 0.1-50 F C15 87-012-368-080 C-CAP,S 0.1-50 F C16 87-012-368-080 C-CAP,S 0.1-50 F C17 87-012-368-080 C-CAP,S 0.1-50 F C18 87-012-368-080 C-CAP,S 0.1-50 F C19 87-016-520-000 CAP,E 3300-65 M SMG C20 87-016-520-000 CAP,E 3300-65 M SMG C21 87-016-051-000 CAP,E 2200-35 M SMG C22

38、87-016-051-000 CAP,E 2200-35 M SMG C23 87-016-658-000 CAP,E 4700-35 M SMG C24 87-016-658-000 CAP,E 4700-35 M SMG C25 87-010-408-080 CAP, ELECT 47-50V C26 87-010-247-080 CAP, ELECT 100-50V C30 87-010-430-080 CAP, ELECT 100-63 C31 87-010-263-080 CAP, ELECT 100-10V C32 87-010-197-080 CAP, CHIP 0.01 DM

39、C34 87-010-260-080 CAP, ELECT 47-25V C35 87-010-380-080 CAP, ELECT 47-16V C36 87-010-381-080 CAP, ELECT 330-16V C38 87-010-197-080 CAP, CHIP 0.01 DM C60 87-010-403-080 CAP, ELECT 3.3-50V C61 87-010-260-080 CAP, ELECT 47-25V C101 87-010-183-080 C-CAP,S 2700P-50 B C102 87-010-183-080 C-CAP,S 2700P-50

40、B C103 87-010-545-080 CAP, ELECT 0.22-50V C104 87-010-545-080 CAP, ELECT 0.22-50V C107 87-010-405-080 CAP, ELECT 10-50V C108 87-010-405-080 CAP, ELECT 10-50V C109 87-010-179-080 C-CAP,S 1200P-50 K B GRM C110 87-010-179-080 C-CAP,S 1200P-50 K B GRM C111 87-010-405-080 CAP, ELECT 10-50V C112 87-010-40

41、5-080 CAP, ELECT 10-50V C113 87-010-866-080 CAP, ELECT 10-63 C114 87-010-866-080 CAP, ELECT 10-63 C119 87-010-197-080 CAP, CHIP 0.01 DM C120 87-010-197-080 CAP, CHIP 0.01 DM C123 87-010-176-080 C-CAP,S 680P-50 SL C124 87-010-176-080 C-CAP,S 680P-50 SL C125 87-012-368-080 C-CAP,S 0.1-50 F C126 87-012

42、-368-080 C-CAP,S 0.1-50 F C127 87-012-368-080 C-CAP,S 0.1-50 F C128 87-012-368-080 C-CAP,S 0.1-50 F C129 87-010-191-080 C-CAP,S 0.015-50 F C130 87-010-191-080 C-CAP,S 0.015-50 F C131 87-010-197-080 CAP, CHIP 0.01 DM C132 87-010-197-080 CAP, CHIP 0.01 DM C133 87-010-186-080 CAP,CHIP 4700P C140 87-010

43、-182-080 C-CAP,S 2200P-50 B C141 87-010-196-080 CHIP CAPACITOR,0.1-25 C203 87-010-182-080 C-CAP,S 2200P-50 B C204 87-010-182-080 C-CAP,S 2200P-50 B C205 87-010-179-080 C-CAP,S 1200P-50 K B GRM C206 87-010-179-080 C-CAP,S 1200P-50 K B GRM C209 87-010-402-080 CAP, ELECT 2.2-50V C210 87-010-402-080 CAP

44、, ELECT 2.2-50V C211 87-010-184-080 CHIP CAPACITOR 3300P(K) C212 87-010-184-080 CHIP CAPACITOR 3300P(K) C213 87-010-402-080 CAP, ELECT 2.2-50V C214 87-010-402-080 CAP, ELECT 2.2-50V C217 87-010-405-080 CAP, ELECT 10-50V C218 87-010-405-080 CAP, ELECT 10-50V C220 87-010-405-080 CAP, ELECT 10-50V C223

45、 87-010-190-080 S CHIP F 0.01 C224 87-010-190-080 S CHIP F 0.01 C228 87-010-405-080 CAP, ELECT 10-50V C229 87-010-196-080 CHIP CAPACITOR,0.1-25 C230 87-010-196-080 CHIP CAPACITOR,0.1-25 C231 87-010-196-080 CHIP CAPACITOR,0.1-25 C232 87-010-196-080 CHIP CAPACITOR,0.1-25 C233 87-010-190-080 S CHIP F 0

46、.01 KANRI NO. REF. NO.DESCRIPTIONPART NO.KANRI NO. REF. NO.DESCRIPTIONPART NO. 7 C234 87-010-190-080 S CHIP F 0.01 C237 87-010-322-080 C-CAP,S 100P-50 CH C238 87-010-322-080 C-CAP,S 100P-50 CH C239 87-010-196-080 CHIP CAPACITOR,0.1-25 C270 87-010-197-080 CAP, CHIP 0.01 DM C301 87-010-178-080 CHIP CA

47、P 1000P C302 87-010-178-080 CHIP CAP 1000P C303 87-010-178-080 CHIP CAP 1000P C304 87-010-178-080 CHIP CAP 1000P C307 87-010-263-080 CAP, ELECT 100-10V C308 87-010-263-080 CAP, ELECT 100-10V C309 87-010-318-080 C-CAP,S 47P-50 CH C310 87-010-318-080 C-CAP,S 47P-50 CH C313 87-010-188-080 CAP,CHIP 6800P C314 87-010-188-080 CAP,CHIP 6800P C315 87-010-263-080 CAP, ELECT 100-10V C317 87-010-546-080 CAP, ELECT 0.33-50V C318 87-010-546-080 CAP, ELECT 0.33-50V C326 87-010-198-080 CAP, CHIP 0.022 C327 87-012-368-0