Sony Satw60 电路图.pdf

《Sony Satw60 电路图.pdf》由会员分享，可在线阅读，更多相关《Sony Satw60 电路图.pdf（62页珍藏版）》请在收音机爱好者资料库上搜索。

1、SPECIFICATIONS SERVICE MANUALSAT-W60 RM-Y804 U.S. Model INTERNET TERMINAL Terminals: Dimensions: (w/h/d) Weight: Video In (2) Video Out (2) Audio (R/L) In (2) Audio (R/L) Out (2) S-Video In (1) /Out (1) Tel Line (1) Microphone In (1) Printer Port (DB25) (1) VCR Control (1) Digital Audio Out (1) USB

2、Port (2) Satellite In (2) CH3-CH4 Switch (1) VHF/UHF In/Out (1) AC In (1) 430 x 70 x 290 mm (w/h/d) (17 x 23/4 x 111/2 inches) Approx. 4.3 kg (9.4 lbs.) Power Requirements: Power Consumption: Supplied Accessories: Optional Accessories: AC 120V 90 W Max Remote Control RM-Y804 (1) Size AA Batteries (2

3、) AC Power Cord (1) A/V (Audio/Video) Cable (1) Telephone Cable (1) S-Video Cable (1) T Splitter (1) Coaxial Cable (1) IR Blaster (1) Wireless Keyboard KI-W250 (1) Access Card (1) Local Antenna ANJ-AA1 Installation Kit ANJ-DS2 Amplifier EAC-DA1 Diplexer EAC-DD1 Voltage Switch EAC-DV2 Satellite Dish

4、Antenna: SAN-24MD1 SAN-18D4 Design and specifications are subject to change without notice. SAT-W60 RM-Y804 9-965-897-02 RadioFans.CN 收音机爱 好者资料库 2 SAT-W60 SAFETY CHECK-OUT After correcting the original service problem, perform the following safety checks before releasing the set to the customer: Lea

5、kage Test The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microampere). Leakage current can be measured by any one of three methods. 1. A commercial leakage tester, such as t

6、he Simpson 229 or RCA WT-540A. Follow the manufacturers instructions to use these instructions. 2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmete

7、r. The limit indication is 0.75 V, so analog meters must have an accurate low voltage scale. The Simpsons 250 and Sanwa SH-63Trd are examples of passive VOMs that are suitable. Nearly all battery operated digital multimeters that have a 2V AC range are suitable. (See Figure A) 1. Check the area of y

8、our repair for unsoldered or poorly- soldered connections. Check the entire board surface for solder splashes and bridges. 2. Check the interboard wiring to ensure that no wires are “pinched” or contact high-wattage resistors. 3. Check that all control knobs, shields, covers, ground straps, and moun

9、ting hardware have been replaced. Be absolutely certain that you have replaced all the insulators. 4. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement. 5. Look for parts whi

10、ch, though functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. 6. Check the line cords for cracks and abrasion. Recommend the replacement of any such line cord to the customer. 7. Check the B+ and HV to see if they are specified values. M

11、ake sure your instruments are accurate; be suspicious of your HV meter if sets always have low HV. 8. Check the antenna terminals, metal trim, “metallized knobs, screws, and all other exposed metal parts for AC Leakage. Check leakage as described below. 1.5 k0.15 F AC Voltmeter (0.75 V) To Exposed M

12、etal Parts on Set Earth Ground Figure A RadioFans.CN 收音机爱 好者资料库 3 SAT-W60 TABLE OF CONTENTS Section TitlePage Safety Check Out Instructions . 2 1.GENERAL. 4 2.DISASSEMBLY 2-1. Upper Cover Removal . 10 2-2. Hard Drive Removal . 10 3.SYSTEM SELF TEST .11 4.DIAGRAMS 4-1. Block Diagram . 12 4-2. Schemat

13、ic Diagrams. 13 5.EXPLODED VIEWS 5-1. Front Panel View . 53 5-2. Rear View. 54 5-3. SAN-18D4 . 55 5-4. SAN-24MD1 . 55 6. ELECTRICAL PARTS LIST . 56 RadioFans.CN 收音机爱 好者资料库 4 SAT-W60 The instructions mentioned here are partial abstracts from the Operating Instruction Manual. The page numbers shown re

14、flect those of the Operating Instruction Manual. SECTION 1 GENERAL Satellite Receiver 10 Step 1: Connecting the Antenna Step 2: Connecting Your Phone Line Satellite Receiver Connect the SATELLITE IN jack to your Satellite Dish Antenna using RG-6 coaxial cable. Connect the 2nd signal if you have Dual

15、 LNB. Advance Set Up for dual output. 1 12 2 Satellite Receiver Connect the TELEPHONE LINE jack to a telephone line wall jack using the supplied telephone cord. 11 Connecting Your Satellite Receiver 11 Step 3: Connecting Your TV Set VHF / UHF AUDIO L R (MONO) VIDEO IN VIDEO 1 VIDEO 2 TV S VIDEO Sate

16、llite Receiver 1a 1b 1c If your TV has A/V input jacks Connect the VIDEO OUT jacks on your Satellite Receiver to the A/V input jacks on your TV using the supplied A/V cable. (Be sure to match the colors on the jacks with the colored plugs on the A/V cable.) If your TV has only one audio input, conne

17、ct it to the L(MONO) jack on the Satellite Receiver. If your TV has an S-Video input Use an S-Video cable instead of the yellow video connection. S-Video cable is supplied. If your TV does not have A/V jacks Connect the VHF/UHF OUT jack to the VHF/UHF input jack on your TV using coaxial cable. Set t

18、he CH3/CH4 switch to the channel that does not carry off-air broadcasts in your area. 1a 1b 1c Note With this connection, your input source is channel 3 or channel 4 depending on how you set the CH3/CH4 switch on the Satellite Receiver. 5 SAT-W60 Satellite Receiver 12 Step 4: Connecting the AC Power

19、 Step 5: Checking the Access Card Step 6: Activating Your Service After checking the DIRECTV Access Card and your Satellite Dish Antenna is installed, you are ready to begin enjoying service. Call DIRECTV at 1-800-DIRECTV (347-3288) to begin digital satellite programming. For DIRECTV and UltimateTV

20、operational instructions, please refer to the User Guide. Satellite Receiver AC Power Cord to power outlet After all other connections are complete, connect the AC Power Cord to the Satellite Receiver. Then connect the AC Power Cord to a power outlet. 1 1 Satellite Receiver 1 1 Open the access door

21、by applying gentle pressure to the latch and releasing. Make sure the DIRECTV Access Card is firmly inserted into the front left hand slot of the Satellite Receiver. After the DIRECTV Access Card is inserted (correctly), DO NOT remove it unless instructed to do so by your service provider. Connectin

22、g Your Satellite Receiver 13 Advanced Connection: Connecting Your VCR VIDEOS VIDEOAUDIO LINE IN LINE OUT IN OUT VCR Satellite Receiver If your TV and VCR have A/V jacks Connect the VIDEO OUT jacks of your Satellite Receiver to the A/V input jacks of your VCR using the supplied A/V cable. Then, conne

23、ct the A/V output jacks of your VCR to the A/V input jacks of your TV using an A/V cable. (Be sure to match the colors on the jacks with the colored plugs on the A/V cable.) Some TVs and VCRs do not have stereo audio, if yours does not, just connect the white A/V cable to the Left output jack. 1c 1b

24、 1a 1a 1b z Tip To allow your Satellite Receiver to control the recording functions of your VCR, see page 14. If your TV and VCR do not have A/V jacks Connect the VHF(SAT)/UHF OUT jack on the Satellite Receiver to the VHF/UHF input jack on your VCR using coaxial cable. Then, connect the VHF/UHF outp

25、ut jack on your VCR to the VHF/UHF input jack on your TV using a second coaxial cable. Set the CH3/CH4 switch to the channel that does not carry off-air broadcasts in your area. 1c If your TV and VCR have S-Video jacks Use an S-Video cable instead of the yellow video connection. S-Video cable is sup

26、plied. Note With this connection, your input source is channel 3 or channel 4 depending on how you set the CH3/CH4 switch on 6 SAT-W60 Satellite Receiver 14 Advanced Connection: Connecting Your IR Blaster 1/2 to 1 Satellite Receiver VCR (front)IR Sensor In front of the VCR Place the IR Blaster under

27、 and in front of the VCR. The IR Blaster must extend just in front of the infrared sensor of the VCR. 1 2 2 1 To allow the Satellite Receiver to control your VCR Connect the IR Blaster to the VCR CONTROL jack on the Satellite Receiver. z Tip If the infrared sensor is not marked on your VCR, shine a

28、flashlight into the front panel of the VCR to locate the sensor. Connecting Your Satellite Receiver 15 Advanced Connection: Connecting an Audio System Advanced Connection: Connecting a Microphone LINE IN LINE OUT AUDIO OPTICAL IN Audio Receiver Satellite Receiver If you have a digital or Dolby Digit

29、al audio system Connect the DIGITAL OUT (OPTICAL) of the Satellite Receiver to the optical digital input of your audio system. 1 1 PUSHPUSH SATELLITE RECEIVER SAT-W60 GUIDEHOME Satellite Receiver 1 1 If you have a Microphone First, remove the cover from the microphone jack, then connect the micropho

30、ne plug to the Satellite Receivers Microphone IN jack. z Tip If you connect your Satellite Receiver to a Dolby Digital receiver, set the Dolby Digital option of the Audio display to Auto Select. z Tip Check “Help” screen for a list of compatible microphones. 7 SAT-W60 Satellite Receiver 16 Advanced

31、Connection: Connecting a Printer Connecting a printer to your Satellite Receiver enables you to print Web pages and e-mail messages. The Satellite Receiver is not compatible with all printers. Check the on-line instructions for a list of the latest compatible printers. Advanced Connection: Connectin

32、g a Camcorder Printer DB-25 Male Satellite Receiver To print screens Connect the printer port on the Satellite Receiver to the port on the printer. Note Unplug the Satellite Receiver and printer before you begin connecting. Satellite Receiver PUSHPUSH SATELLITE RECEIVER SAT-W60 GUIDEHOME 1 If you ha

33、ve a Camcorder First, remove the cover from the A/V jacks, then, using A/V cables, connect the camcorders A/V OUT jacks to the Satellite Receivers A/V IN jacks. Note If you have a mono camcorder, connect its left audio output to the Satellite Receivers AUDIO L (white) jack. 1 Using the Remote Contro

34、l and Basic Functions 19 MutingPress to mute the sound. Press again, or press VOL +, to restore the sound. (For the TV only) TV/VIDEO Cycles through the video inputs of your TV. TV POWER Turns your TV on and off. SAT POWER Turns your Satellite Receiver on and off. PIPTurns the Picture-in-Picture fea

35、tures of the Satellite Receiver on and off. WINDOWSelects the active window while in PIP mode, allowing you to change the Main or PIP window.(For the Satellite Receiver only) TV FUNCTIONSelects TV feature control. SAT FUNCTIONSelects Satellite Receiver feature control. ButtonReview button. ButtonPla

36、y button. ButtonForward scan button. ButtonRecord button. ButtonStop button. ButtonPause button. ButtonReplay button. ButtonJump ahead button. 0 9 ButtonsSelect channels or enter numbers in text boxes. Adds period to separate major/minor channel numbers. MENUOpens the TV Main Menu. EXITCloses all on

37、-screen displays, including program guides and menus. ENTERActivates the selected channel on your TV. 12 456 789 0 . 3 RM-Y804 CHVOL SCROLL INFOOPTIONS EXIT RECENT TV/WEB MENU PIP POWERMUTING WINDOW TV/VIDEO TV TV FUNCTION SAT SAT ENTER MY SHOWS GUIDE CODE SET BACKHOME . 8 SAT-W60 Satellite Receiver

38、 20 OPTIONSDisplays the OPTIONS panel. RECENTDisplays and allows you to access the most recently viewed Web pages and TV channels. SCROLL V/v Buttons Moves the page up or down when the page is too long to be displayed on the screen. HOME Displays the Web Home or TV Home screen. BACKDisplays the last

39、 screen viewed, or hides the on-screen keyboard. TV/WEBPress the button to switch between TV and WebTV modes. Arrow ButtonsMove the yellow highlight box to a different command or activity on the screen; select different keys when the on-screen keyboard is displayed. MY SHOWSDisplays a list of progra

40、ms that you have recorded with your Satellite Receiver. INFODisplays information on the program you are viewing. GUIDEDisplays information on available programs, including channel, time and date. ButtonActivates a highlighted link or command; displays the on-screen keyboard. VOL +/Increases and decr

41、eases the volume. CH +/Moves to the next or previous channel. CODE SETUsed for programming the remote control to operate your TV. See page 21 for details. Satellite Receiver 26 Troubleshooting SymptomPossible Cause and remedies TV POWER button doesnt turn on TV. The remote control has not been prope

42、rly programmed. See “Setting up the Remote Control” on page 21. The batteries in the remote control or wireless keyboard could be weak. Check the batteries and replace them if necessary. No picture, no sound.Make sure the AC Power Cord is connected. Check that the TV/VIDEO switch is set correctly. M

43、ake sure the Satellite Receiver is properly connected. If you connected using a S-Video or A/V cables, make sure they are properly connected. If your TV must be set to a certain channel to view other devices to which it is connected, make sure this channel is selected. Check that the correct video i

44、nput is selected by pressing the TV/VIDEO button. If your TV is not connected using the S-Video or A/V cables, set the CH3-CH4 switch on the back of the Satellite Receiver to the opposite channel to which it is currently set. No sound.If you connected the Satellite Receiver using A/V cables, make su

45、re the cables are properly connected. Cant change TV channels while using WebTV service. Make sure you select the TV FUNCTION button. The WebTV service screens disappear after pressing the CHANNEL +/ buttons. Press the TV/VIDEO button on the remote control until the WebTV screen appears. VCR Control doesnt seem to be working correctly. Check that the IR Blaster is positioned directly in front of the infrared sensor area of your cable box and/or VCR. Follow the on-line instructions