IC-7100_serv.pdf

《IC-7100_serv.pdf》由会员分享，可在线阅读，更多相关《IC-7100_serv.pdf（84页珍藏版）》请在收音机爱好者资料库上搜索。

1、S-15008XZ-C1 July 2013 HF/VHF/UHF ALL MODE TRANSCEIVER This service manual describes the latest technical information for the IC-7100 HF/VHF/UHF ALL MODE TRANSCEIVER, at the time of publication. NEVER connect the transceiver to an AC outlet or to a DC power supply that uses more than the specifi ed

2、voltage. This will ruin the transceiver. DO NOT expose the transceiver to rain, snow or liquids. DO NOT reverse the polarities of the power supply when con- necting the transceiver. DO NOT apply an RF signal of more than 20 dBm (100 mW) to the antenna connector. This could damage the transceivers fr

3、ont-end. To upgrade quality, any electrical or mechanical parts and internal circuits are subject to change without notice or obligation. MODELVERSION VERSION NUMBER IC-7100 USA#02 EUR#03 EUR-01#04 ITR#05 ESP#06 TPE#07 KOR#08 CHN#09 FRA#12 EXP#13 Be sure to include the following four points when ord

4、ering replacement parts: 1. 10-digit Icom part number 2. Component name 3. Equipment model name and unit name 4. Quantity required 1110003491 S.IC TA31136FNG IC-7100 MAIN UNIT 5 pieces 8820001210 Screw 2438 screw IC-7100 Top cover 10 pieces Addresses are provided on the inside back cover for your co

5、nvenience. ORDERING PARTS 1. Make sure that the problem is internal before dis-assem- bling the transceiver. 2. DO NOT open the transceiver until the transceiver is dis- connected from its power source. 3. DO NOT force any of the variable components. Turn them slowly and smoothly. 4. DO NOT short an

6、y circuits or electronic parts. An insulated tuning tool MUST be used for all adjustments. 5. DO NOT keep power ON for a long time when the trans- ceiver is defective. 6. DO NOT transmit power into a Standard Signal Generator or a Sweep Generator. 7. ALWAYS connect a 40 dB to 50 dB attenuator betwee

7、n the transceiver and a Deviation Meter or Spectrum Analyzer, when using such test equipment. 8. READ the instructions of the test equipment thoroughly before connecting it to the transceiver. REPAIR NOTES INTRODUCTIONCAUTION Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorp

8、orated (Japan) in Japan, the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries. TABLE OF CONTENTS SECTION 1 SPECIFICATIONS SECTION 2 INSIDE VIEWS SECTION 3 CIRCUIT DESCRIPITON 3-1 RECEIVER CIRCUITS . 3-1 3-2 TRANSMITTER CIRCUITS . 3-2 3-3 FREQUENCY SYNTHESIZER

9、CIRCUITS . 3-4 3-4 VOLTAGE BLOCK DIAGRAM . 3-4 3-5 PORT ALLOCATIONS . 3-5 SECTION 4 ADJUSTMENT PROCEDURES 4-1 PREPARATION . 4-1 4-2 FREQUENCY ADJUSTMENT . 4-3 4-3 TRANSMIT ADJUSTMENT . 4-4 4-4 RECEIVE ADJUSTMENT . 4-5 SECTION 5 PARTS LIST SECTION 6 MECHANICAL PARTS SECTION 7 BOARD LAYOUTS SECTION 8

10、WIRING DIAGRAM SECTION 9 BLOCK DIAGRAM SECTION 10 VOLTAGE DIAGRAM 1-1 SECTION 1. SPECIFICATIONS ? D ? ? ? Receive 0.030000 199.999999*1*2 400.000000 470.000000*1*2 Transmit 1.800000 1.999999*2, 3.500000 3.999999*2, 5.255000 5.405000*1*3, 5.332000*3*4, 5.348000*3*4, 5.358500*3*4, 5.373000*3*4, 5.4050

11、00*3*4, 7.000000 7.300000*2, 10.100000 10.150000*2, 14.000000 14.350000*2, 18.068000 18.168000*2, 21.000000 21.450000*2, 24.890000 24.990000*2, 28.000000 29.700000*2, 50.000000 54.000000*2, 70.000000 70.500000*2, 144.000000 148.000000*2, 430.000000 450.000000*2 *1Some frequency ranges are not guaran

12、teed. *2Depending on version. *3USA version only. *4Center frequency. ? ? WFM (RX only), DV ? ? ?(99CH 5 bank) ? ? 6 CH (2 3 edges) ? ? ?(2 2 band) ? ? 2 ?Antenna impedance: 50 ? 10C to +60C; +14F to +140F ? ? after power ON. (0C to +50C; +32F to +122F at 430 MHz band) ? ? ? ? (negative ground) ? Tr

13、ansmit Max. power: 22.0 A Receive Standby: 0.9 A Max. audio: 1.2 A ? Main unit: 167(W) 58(H) 225(D) mm; 6.6(W) 2.3(H) 8.9(D) in Controller: 165(W) 64(H) 78.5(D) mm; 6.5(W) 2.5(H) 3.1(D) in ? Main unit: 2.3 kg; 5.1 lb Controller: 0.5 kg; 1.1 lb ? ? ? ?110) ? ? ? ?18) Transmitter D ? ?(at 13.8 V DC/+2

14、5C): (continuously adjustable) ? HF/50 MHz2 to 100 W (AM: 1 to 30 W)* 70 MHz2 to 50 W (AM: 1 to 15 W)* 144 MHz2 to 50 W 430 MHz2 to 35 W * In the AM mode, transmission can be performed only on the HF/50/70 MHz frequency band. ? SSB: Digital PSN modulation AM: Digital Low power modulation FM: Digital

15、 Phase modulation DV: GMSK Digital Phase modulation ? (Spurious domain) HF bands: Less than 50 dB 50 MHz band: Less than 63 dB 70/144/430 MHz bands: Less than 60 dB (Out-of-band domain) HF bands: Less than 40 dB 50/70/144/430 MHz bands: Less than 60 dB ? ? ? ? More than 50 dB ? ? ? ? ? ?18) ? ?18) 1

16、-2 Receiver D ? SSB/CW/RTTY/AM/FM/DV: Triple superheterodyne system WFM: Double superheterodyne system ? 1st: 124.487 MHz (SSB/CW/RTTY/AM/FM/DV) 134.732 MHz (WFM) 2nd: 455 kHz (SSB/CW/RTTY/AM/FM/DV) 10.7 MHz (WFM) 3rd: 36 kHz (SSB/CW/RTTY/AM/FM/DV) ? SSB, CW (10 dB S/N): 0.15 V (1.8029.9950 MHz)*1 0

17、.12 V (50 MHz)*2 0.15 V (70 MHz)*2 0.11 V (144/430 MHz)*3 AM (10 dB S/N): 13.0 V (0.51.8 MHz)*1 2.0 V (1.8029.9950 MHz)*1 1.0 V (50/70 MHz)*2 1.0 V (144/430 MHz) FM (12 dB SINAD): 0.5 V (28.029.7 MHz)*1 0.25 V (50/70 MHz)*2 0.18 V (144/430 MHz)*3 WFM (12 dB SINAD): 10.0 V (76108 MHz)*3 DV (1% BER):

18、1.0 V (28.029.7 MHz)*1 0.63 V (50/70 MHz)*2 0.35 V (144/430 MHz)*3 *1 Preamp 1 is ON, *2 Preamp 2 is ON, *3 Preamp is ON ? ? HF*1 SSB : Less than 5.6 V FM: Less than 0.3 V 50/70 MHz*2 SSB : Less than 5.6 V FM: Less than 0.3 V 144/430 MHz*3 SSB : Less than 5.6 V FM: Less than 0.3 V *1 Preamp 1 is ON,

19、 *2 Preamp 2 is ON, *3 Preamp is ON ? SSB (BW: 2.4 kHz): More than 2.4 kHz/6 dB Less than 3.4 kHz/40 dB CW (BW: 500 Hz): More than 500 Hz/6 dB Less than 700 Hz/40 dB RTTY (BW: 500 Hz): More than 500 Hz/6 dB Less than 800 Hz/40 dB AM (BW: 6 kHz): More than 6.0 kHz/6 dB Less than 10.0 kHz/40 dB FM (BW

20、: 15 kHz): More than 12.0 kHz/6 dB Less than 22.0 kHz/40 dB DV (CH space: 12.5 kHz): More than 50 dB ? ? HF band: More than 70 dB 50/70 MHz bands*: More than 70 dB * except 1/2 IF through on 50/70 MHz bands 144/430 MHz bands*: More than 65 dB * except IF through on 144 MHz band ? ? distortion with a

21、n 8 load ? ? ? ? ? ?18) ? ?18)/ 8 ? ? (with 1 kHz single tone) ? ? ? ? (noise rejection in SSB) All stated specifi cations are typical and subject to change without notice or obligation. 2-1 SECTION 2. INSIDE VIEWS DISPLAY UNIT (TOP VIEW) AF MUTE SW (Q403) FRONT CPU CLOCK (X201) DC-DC CONVERTER (IC7

22、01) AF MUTE SW (Q404) KEY BACKLIT DRIVER (IC601) LED DRIVER (IC901) 2-2 DISPLAY UNIT (BOTTOM VIEW) RESET IC (IC202) CURRENT LIMITTER (Q501) CONTROL DATA INTERFACE (IC501) EXTERNAL SEND SW (Q502) AF OUTPUT CONTROL (Q401) FRONT CPU (IC201) 2-3 DC-DC CONVERTER CIRCUIT MAIN UNIT USB CODEC (IC602) SRAM (

23、IC6204) MAIN CPU (IC6202) REAL-TIME CLOCK (IC6201) DV DSP (IC5502) IF DSP (IC5001) EXPANDER (IC7004) EXPANDER (IC7002) +8 V REGULATOR (IC161) DRIVE CURRENT BUFFER (IC12) 1ST LO AMP (IC2401) ALC CONTROLLER (IC1502) S-METER AMP (IC1501) 2ND RX IF FILER (FI4602) 2ND RX IF FILER (FI4601) 1ST DDS CLOCK F

24、ILTER (FI2151) EXPANDER (IC7001) EXPANDER (FI4101) AF LPF (IC5083) +8 V REGULATOR (IC51) MAIN CPU CLOCK (X6202) USB HUB CLOCK (X511) AGC AMP (IC5091) +1.3 V REGULATOR (IC5501) 1/2 DIVIDER (IC5052) SUB CPU CLOCK (X6401) CODEC (IC5071) D/A CONVERTER (IC5072) SUB CPU (IC6401) EXPANDER (IC7005) 3RD RX/T

25、X IF SWITCH (IC4502) 3RD RX/TX IF SWITCH (IC4503) EXPANDER (IC7003) USB CODEC (IC602) USB HUB (IC511) DATA LINE LEVEL CONVERTER (IC11) 2-4 PA UNIT 144 MHz/430 MHz BAND TX POWER DETECT BUFFER (IC651) DRIVE AMP (Q251) “T8V” LINE CONTROLLER (Q292) “14V” LINE SWITCH (Q391) SERIAL TO PARALLEL CONVERTER (

26、IC751) “T8V” LINE SWITCH (Q492) TX POWER AMP (Q301) TX POWER AMP (Q302) HF/50 MHz/70 MHz BAND TX POWER DETECT BUFFER (IC960) 3-1 RF CIRCUITS LPF TABLE SECTION 3. CIRCUIT DESCRIPTION 3-1 RECEIVER CIRCUITS RF CIRCUIT (PA UNIT) While operating on the HF, 50 MHz and 70 MHz bands The RX signal from the a

27、ntenna connector (ANT1: J1) is passed through the power/SWR detect circuit (D961 and D962) and one of the LPFs, depending on the operating band, to remove unwanted out-of-band signals. (See the LPF TABLE below.) The fi ltered RX signal is passed through the TX/RX SW (RL801) and LPF (L801, L802, C801

28、, C803 and C805) for fur- ther removal of unwanted signals, and then passed through the mute SWs (D181 and D182). When the attenuator is turned ON, the RX signal is passed through the 18 dB attenuator (MAIN UNIT: D3082 and D3083). The RF signal is passed through one of the BPFs, depend- ing on the o

29、perating frequency, to remove unwanted signals. (See the BPF TABLE on page 3-2.) The fi ltered signal is applied to the pre-AMP circuit. PRE-AMP CIRCUIT (MAIN UNIT) When the pre-AMP is turned ON, the RX signal is amplifi ed by the pre-AMP (Q3201). The amplifi ed signal is applied to the 1st RX IF ci

30、rcuits. LPF BPF LPF “L1” “L2” “L3” “L4” “L5” “L6” “L7” D961,D962 PWR/SWR DET TX/RX SW ATT BPF TX/RX SW LPF HPF TX/RX SW ANTENNA LPF ANTENNA BPF LPF PWR/SW R DET LPF LPF MUTE LPF LPF ATT LPF PRE AM P RF AMP PRE AM P BPF MUT E 144 MHz band 7.3-14.35MHz 430 MHz band fc=270M fc=74.8MHz From the TX circu

31、it PA UNIT fc=200M 21.45-33.0MHz 14.35-21.45MHz fc=700M 144/430MHz 430 MHz HF/50MHz/70MHz 144 MHz 0.03-2.0MHz 2.0-4.0MHz 4.0-7.3MHz 33.0-74.8MHz (74.8-200 MHz) (74.8-200MHz) D181,D182 Q481Q451 Q551 D422,423,424 D433,D434 D651,D661 (400-470 MHz) (400-470MHz) 20dB 20dB HPF LPF MUTE D3072 HPF BPF ATT B

32、RF HPF HPF LPF “B1” LPF HPF HPF PRE AMP Q3201 HPF 13.9-20.9MHz fc=500MHz 1.6-2.0MHz 2.0-3.4MHz 6.9-13.9MHz 3.4-6.9MHz 0.03-1.6MHz 74.8MHz and below 74.8MHz or above To the 1st RX IF circuit (74.8MHz and below) To the 1st RX IF circuit (74.8MHz or above) 40.0-60.0MHz 1.6-74.8MHz 60.0-74.8MHz 18dB 20.

33、9-40.0MHz fc=74.8MHz D3272 “B2” “B3” “B4” “B5” “B6” “B7” “B8” “B9” From the TX circuit From the TX circuit Filter Operating frequency (MHz) Filter switchesComponents Control line (Active High) L1 0.030000 to 1.999999RL880 RL881 L881, L882 C882 to C886, C888 to C890, C893, C894, C896, C897, C899L1 L2

34、 2.000000 to 3.999999RL920 RL921 L921, L922, C922 to C929, C933, C984L2 L3 4.000000 to 7.300000RL840 RL841 L841 to L843, C842 to C848, C850, C854 to C859L3 L4 7.300001 to 14.350000RL900 RL901 L901 to L903, C902, C907L4 L514.350001 to 21.450000RL940 RL941 L942, L943, C944 to C947, C950, C953L5 L621.4

35、50001 to 32.999999RL820 RL821 L822, L823, C824 to C828, C833, C835L6 L733.000000 to 74.799999RL860 RL861 L861 to L863, C863 to C866, C868, C869, C873, C875 to C878L7 3-2 BPF TABLE While operating on the 144 MHz and 430 MHz bands The RX signal from the antenna connector (ANT2) is passed through the p

36、ower/SWR detect circuit (D651 and D661) and LPF (L591 to L593, C591 and C592). 144 MHz BAND SIGNAL The RX signal is passed through the LPF (L541 to L543, C542 to C547) and TX/RX SW (RL531). When the attenuator is turned ON, the RX signal is also passed through the 20 dB attenuator (D551 and D552). T

37、he RX signal is then passed through the BPF (MAIN UNIT : D553 to D556, L552, L553 and C553) and applied to the pre-AMP (Q551). The amplifi ed signal is passed through another BPF (MAIN UNIT: D557 to D560, L557 and C561), RX mute (D181 and D182), BPF (MAIN UNIT: D3272, L3271, L3272, C3271 to C3273) a

38、nd LPF (L3261 to L3263, C3261 to C3267), and then applied to the 1st RX IF circuit. 430 MHz BAND SIGNAL The RX signal is passed through the HPF (L441, L442, C441 to C443), mute SW (D433 and D434) and TX/RX SW (D422 to D424). When the attenuator is turned ON, the RX signal is also passed through the

39、18 dB attenuator (D451 and D452). The RX signal is then passed through the BPF (MAIN UNIT : D454, L452 and C454) and applied to the pre-AMP (Q451). The amplifi ed signal is passed through the 2-staged BPF (MAIN UNIT: D455, L453, C468 and D456, L454, C473), and applied to the RF AMP (Q481). The ampli

40、fi ed signal is passed through the RX mute (D181 and D182), BPF (D3272, L3271, L3272, C3271 to C3273) and LPF (L3261 to L3263, C3261 to C3267), and then ap- plied to the 1st RX IF circuit. Filter Operating frequency (MHz) Filter switchesComponents Control line (Active High) B0 0.030000 to 1.599999D3

41、111 D3112L3112, C3112, C3113, C3115B0 B1 1.600000 to 1.999999D3121 D3122L3103 to L3106, C3102 to C3106B1 B1 and B2 2.000000 to 3.399999D3121 D3122 and D3131 D3132 L3103 to L3106, C3102 to C3106 and L3132, L3133, C3132 to C3137 B2 B1 and B3 3.400000 to 6.899999D3121 D3122 and D3141 D3142 L3103 to L31

42、06, C3102 to C3106 and L3142, L3143, C3142 to C3146 B3 B1 and B4 6.900000 to 13.899999D3121 D3122 and D3151 D3152 L3103 to L3106, C3102 to C3106 and L3152, L3153, C3152 to C3156 B4 B1 and B513.900000 to 20.899999D3121 D3122 and D3161 D3162 L3103 to L3106, C3102 to C3106 and L3162, L3163, C3162 to C3

43、166 B5 B1 and B620.900000 to 39.999999D3121 D3122 and D3171 D3172 L3103 to L3106, C3102 to C3106 and L3172, L3173, C3172 to C3176 B6 B1 and B740.000000 to 59.999999D3121 D3122 and D3181 D3182 L3103 to L3106, C3102 to C3106 and L3182, L3183, C3182 to C3187 B7 B1 and B860.000000 to 74.799999D3121 D3122 and D3191 D3192 L3103 to L3106, C3102 to C3106 and L3192, L3193, C3192 to C3196 B8 3-3 1ST RX IF CIRCUIT (MAIN