Vertex_VX-5500_user.pdf

《Vertex_VX-5500_user.pdf》由会员分享，可在线阅读，更多相关《Vertex_VX-5500_user.pdf（16页珍藏版）》请在收音机爱好者资料库上搜索。

1、VX-5500 OPERATING MANUAL POWER VERTEX STANDARD CO., LTD. 4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan VERTEX STANDARD US Headquarters 10900 Walker Street, Cypress, CA 90630, U.S.A. International Division 8350 N.W. 52nd Terrace, Suite 201, Miami, FL 33166, U.S.A. YAESU EUROPE B.V. P.O. Box 7552

2、5, 1118 ZN Schiphol, The Netherlands YAESU UK LTD. Unit 12, Sun Valley Business Park, Winnall Close Winchester, Hampshire, SO23 0LB, U.K. VERTEX STANDARD HK LTD. Unit 5, 20/F., Seaview Centre, 139-141 Hoi Bun Road, Kwun Tong, Kowloon, Hong Kong Vertex Standard Co., Ltd. FCC ID: K66VX-5500V Congratul

3、ations! You now have at your fingertips a valuable communications tool - a two-way radio! Rugged, reliable and easy to use, your radio will keep you in constant touch with your colleagues for years to come, with negligible maintenance down time. Please take a few minutes to read this manual carefull

4、y. The information presented here will allow you to derive maximum performance from your radio. After reading it, keep the manual handy for quick reference, in case questions arise later on. Were glad you joined the team. Call on us any time, because our business is communications. Let us help you g

5、et your message across. NOTICE There are no user-serviceable points inside this transceiver. All service jobs must be referred to your Authorized Service Center or Network Administrator. Safety / Warning Information WARNING - DO NOT operate the VX-5500V radio when someone (bystanders) outside the ve

6、hicle is within following range. Safety Training information: Antennas used for this transmitter must not exceed an antenna gain of 0 dBd. The radio must be used in vehicle-mount configurations with a maximum operating duty factor not exceeding 50%, in typical Push-to-Talk configurations. This radio

7、 is restricted to occupational use, work related operations only where the radio operator must have the knowledge to control the exposure conditions of its passengers and bystanders by maintaining the minimum separation distance of following range. Failure to observe these restrictions will result i

8、n exceeding the FCC RF exposure limits. Antenna Installation: For rear deck trunk installation, the antenna must be located at least the following range away from rear seat passengers and bystanders in order to comply with the FCC RF exposure requirements. For roof top installation, the antenna must

9、 be placed in the center of the roof. Radiated frequency and Distance VX-5500V (C) 1.97 Feet (0.6 m) FCC ID: K66VX-5500V Vertex Standard Co., Ltd. Page 1 VX-5500 Operating Manual VX-5500 Operating Manual The VX-5500 Series are full-featured FM transceivers designed for flexible mobile and base stati

10、on business communications in the VHF (50/10 Watts: programmable) Land Mobile Bands. Each model is designed for reliable business communications in a wide variety of applications, with a wide range of operating capability provided by its leading- edge design. The 250-channels memories can each be pr

11、ogrammed with a 8-character channel name. Important channel frequency data is stored in EEPROM and flash memory on the CPU, and is easily programmable by dealers using a personal computer and the VERTEX STAN- DARD CT-71 Programming Cable and CE49 Software. The pages which follow will detail the many

12、 advanced features provided on the VX-5500 transceiver. After reading this manual, you may wish to consult with your Network Ad- ministrator regarding precise details of the configuration of this equipment for use in your application. POWER Vertex Standard Co., Ltd. FCC ID: K66VX-5500V Page 2 VX-550

13、0 Operating Manual CONTROLS background noise will now be heard, and you may use this to set the VOL- UME knob for the desired audio level. Press and hold the MON button more than 1/2 seconds to quiet the noise and resume normal (quiet) monitoring. Transmitting To transmit, wait until the “BUSY” indi

14、cator is off (the channel is not in use), and press the PTT (Push-To-Talk) switch on the side of the microphone (the “TX” indica- tor will appear or the “TX” indicator will glow red). While holding in the PTT switch, speak across the face of the microphone in a clear, normal voice level, and then re

15、lease the PTT switch to receive. Selecting Groups and Channels H Press the UP (?) or DOWN (?) button (repeatedly, if necessary) to select a different group of channels. H Turn the CHANNEL selector knob to select a different channel within the current group. Automatic Time-Out Timer If the selected c

16、hannel has been programmed for automatic time-out, you must limit the length of each transmission. While transmitting, a beep will sound five seconds before time-out. Another beep will sound just before the deadline; the “TX” indicator will disappear and transmission will cease soon thereafter. To r

17、esume transmitting, you must release the PTT and wait for the “penalty timer” to expire (if you press the PTT before this timer expires, the timer restarts, and you will have to wait another “penalty” period) Vertex Standard Co., Ltd. FCC ID: K66VX-5500V Page 6 VX-5500 Operating Manual POWER ADVANCE

18、D OPERATION Programmable Function Button (PF button) The VX-5500 includes the seven Programmable Function Buttons (PF button). The PF button functions can be customized, via programming by your VERTEX STAN- DARD dealer, to meet your communications/network requirements. Some features may require the

19、purchase and installation of optional internal accessories. The possible PF button programming features are illustrated at the below, and their functions are explained on page 8. For further details, contact your VERTEX STANDARD dealer. For future reference, check the box next to each function that

20、has been assigned to the PF button on your particular radio, and keep it handy. Functions Programmable Function Button (PF button) None SCAN (SCN) Dual Watch Call/Reset Talk-Around (TA) Alpha Numeric (A/N) DIMMER (DIM) Emergency (EMG) Horn Alert (HA) Home Channel (HOM) Intercom (IC) Low Power (LOW)

21、GRP UP GRP DWN CH UP CH DWN AUX A AUX B AUX C Public Address (PA) Monitor (MON) 1.5 sec1.5 sec1.5 sec1.5 sec1.5 sec1.5 sec1.5 sec Vertex Standard Co., Ltd. FCC ID: K66VX-5500V Page 7 VX-5500 Operating Manual ADVANCED OPERATION 1.5 sec1.5 sec1.5 sec1.5 sec1.5 sec1.5 sec1.5 sec Functions Programmable

22、Function Button (PF button) RCL Selectable Tone (ST) SP* Squelch Level (SQL) Compander Encryption* (OPT) * requires RMK-4000 * requires Encryption Unit Channel Scan The Scanning feature is used to monitor multiple signals programmed into the trans- ceiver. While scanning, the transceiver will check

23、each channel for the presence of a signal, and will stop on a channel if a signal is present. To activate scanning: H Press the assigned PF button of the “Scan” momentarily to activate scanning. H The scanner will search the channels, looking for active ones; it will pause each time it finds a chann

24、el on which someone is speaking. To stop scanning H Press the assigned PF button of the “Scan”. H Operation will revert to the channel to which the CHANNEL selector knob is set. Note:Your dealer may have programmed your radio to stay on one of the following channels if you press the PTT switch durin

25、g scanning pause: Current channel (“Talk Back”) “Last Busy” channel “Priority” channel “Home” channel “Scan Start” channel Dual Watch The Dual Watch feature is similar to the Scan feature, except that only two channels are monitored: The current operating channel; and The “Priority” channel. To acti

26、vate Dual Watch: H Press the assigned PF button of the “Dual Watch”. H The scanner will search the two channels; it will pause each time it finds a channel on which someone is speaking. To stop Dual Watch: H Press the assigned PF button of the “Dual Watch”. H Operation will revert to the channel to

27、which the CHANNEL selector knob is set. Vertex Standard Co., Ltd. FCC ID: K66VX-5500V Page 8 VX-5500 Operating Manual ARTS (Auto Range Transpond System) This system is designed to inform you when you and another ARTS-equipped station are within communication range. During ARTS operation, your radio

28、automatically transmits for about 1 second every 25 (or 55) seconds (the interval is programmed by Dealer) in an attempt to Shake hands with the other station. If you move out of range for more than one minutes, your radio senses that no signal has been received, a ringing beeper will sound. If you

29、subsequently move back into range, as soon as the other station transmits, your beeper will sound. The PF Button Function The PF (Programmable Function) button can be programmed by the dealer to provide two of the other functions described below. To activate the primary Accessory function, press the

30、 PF button momentarily. To access the secondary Accessory function (which may include the Alarm), press and hold the PF button for 1.5 seconds or longer. Call/Reset When this feature is programmed and a selective call has been received, momen- tarily press the assigned PF button of the “Call/Reset”

31、to reset the flashing indicator and mute the receiver, otherwise press the assigned PF button of the “Call/Reset” to sent your radios identification code (ANI) to the dispatcher. Talk-Around The feature causes the assigned PF button of the “Talk-Around” to select simplex operation on semi-duplex cha

32、nnels: the transmit frequency becomes the same as the receive frequency (regardless of any programmed offset for the channel). Note:This feature has no effect on simplex channels. After pressing the button, “-TAKARD-” is displayed on the LCD. Alpha Numeric Press the assigned PF button of the “Alpha

33、Numeric” to switch the display between the Group/Channel number, and the Group/Channel name (alphanumeric). A tone will sound each time you switch between numerical and alphanumerical display. DIM Press the assigned PF button of the “DIM” to adjust the brightness of the display and key backright. AD

34、VANCED OPERATION Vertex Standard Co., Ltd. FCC ID: K66VX-5500V Page 9 VX-5500 Operating Manual EMG (Emergency) Press the assigned PF button of the “EMG” to initiate an emergency call (requires ANI board). When an emergency call is made, not tone is emitted and the display does not change. To end the

35、 emergency call, turn the transceiver power OFF. HA (Horn Alert) Press the assigned PF button of the “HA” to turn the Horn Alert function ON or OFF. If you receive a call from the base station with 2Tone or DTMF signaling, horn alert will activate. When you turn Horn Alert ON, a tone will sound and

36、“ ” appears on the display. Home (Home Channel) Press the assigned PF button of the “Home” to select the pre-programmed Home Channel. Press it again to return to the previous channel. If used while scanning, pressing this key a second time will change to the revert channel. IC (Intercom) This featur

37、e requires dual head configuration. Press the assigned PF button of the “IC” to turn the intercom feature ON or OFF. While ON, you can press the PTT switch to communicate to another control head operator without transmitting over the air. When you press this key, a tone sounds and “” appears on the

38、display. The intercom can be used even while scanning and receiving a call Low Power Press the assigned PF button of the “Low Power” to set the radios transmitter to the “Low Power” mode. Press this key again to return to “High Power” operation when in difficult terrain. GRP UP/DWN Press the assigne

39、d PF button of the “GRP UP” or “GRP DWN” to select a different group of channels. CH UP/DWN Press the assigned PF button of the “CH UP” or “CH DWN” to select a different channel within the current group. AUX A/B/C Press the assigned PF button of the “AUX A”, “AUX B”, or “AUX C” to turn the output po

40、rt (respectively). PA (Public Address) Press the assigned PF button of the “PA” to use the transceiver as a PA amplifier. When you enable this function, a tone sounds and “” appears on the display. The public address can be used even while scanning and receiving a call. ADVANCED OPERATION Vertex Sta

41、ndard Co., Ltd. FCC ID: K66VX-5500V Page 10 VX-5500 Operating Manual MONI (Monitor) Press the assigned PF button of the “MONI” momentarily to cancel CTCSS and DCS signaling squelch; the “MON” icon appears on the display. Press and hold this key for 1/2 seconds to hear background noise (unmute the au

42、dio); the MON icon blinks on the display. RCL (Channel Recall) During scan, you can press the assigned PF button of the “RCL” to select the last called channel. ST (Selectable Tone) Press the assigned PF button of the “Selectable Tone”, then rotate the CHANNEL selector knob to select a 2-Tone. SP Pr

43、ess the assigned PF button of the “SP” to switch “Front panel”, “Front panel & Body” and “Body” speaker. When “Body” is selected, a tone sounds and the “” icon appears on the display. You can use this function while scanning and receiving a call. However, all audio will be emitted from the PA speake

44、r. SQL (Squelch Level) You can manually adjust the squelch level using this function: 1. Press the assigned PF button of the “SQL”. A tone sounds and SQL appears on the display with the current squelch level. 2. Rotate the CHANNEL selector knob to select the desired level. 3. Press the this key. A t

45、one sounds and the display returns to the normal channel. COMP (Compander) Press the PF button assigned to the “COMP” function to turn the “Compander” IC ON or OFF. This IC contains two variable gain circuits configured for compressing and expand- ing the dynamic range of the radios transmitted and

46、received audio signal. When you enable this function, the signal-to-noise radio can be improved by reduc- ing the transmitted audio dynamic range. Encryption (Option) When the Voice Scrambler feature is enabled, pressing the assigned PF button of the “Encryption” toggles the Scrambler on and off. AD

47、VANCED OPERATION Vertex Standard Co., Ltd. FCC ID: K66VX-5500V Page 11 VX-5500 Operating Manual OPTIONAL ACCESSORIES MH-25B7AMicrophone MH-53C7AHeavy Duty Microphone MH-53A7AHeavy Duty Microphone w/Noise Canceler MH-53B7AHeavy Duty DTMF Microphone w/Noise Canceler CE49Programming Software CT-70Radio

48、 Programming Cable (Requires VPL-1) CT-71Radio to PC Programming Cable CT-72Radio to Radio Programming Cable CT-81Cable for RMK-4000 (6 m) CT-82Cable for RMK-4000 (2.5 m) CT-83Cable for RMK-4000 (0.6 m) CNT-6000Control Head RF DECKRF Deck w/MMB-79 (for Dual Band Installations) RMK-4000SHRemote Kit (

49、for Single Transceiver) RMK-4000DHRemote Kit (for Dual-Head Installations) RMK-4000DBRemote Kit (for Dual Band Installations) RMK-4000DBHRemote Kit (for Dual Band plus Dual Head Installations) F2D-82-Tone Decode Unit (Requires FIF-7) F5D-145-Tone ENC-DEC Unit (Requires FIF-7) VTP-50VX-Trunk Unit (Requires FIF-7) FVP-25Encryption/DTMF pager Unit (Requires FIF-7) FP-1030External 30A Power Supply MLS-100Mobile Loud speaker (12 W Peak Power) MMB-79Mobile Mounting Bracket MMB-77Locking Mobile Mounting Bracket FIF-7Inter face Board (for F2D-8, F5D-14, VTP-50, FVP-25) CN-6Inter fac