Kenwood_TK-3207_serv.pdf

《Kenwood_TK-3207_serv.pdf》由会员分享，可在线阅读，更多相关《Kenwood_TK-3207_serv.pdf（61页珍藏版）》请在收音机爱好者资料库上搜索。

1、UHF FM TRANSCEIVER / UHF 调频对讲机 TK-3207 2004-2 PRINTED IN JAPAN B51-8680-00 (S) 663 SERVICE MANUAL / 维修手册 Antenna 天线 (T90-1039-05): M (T90-0798-15): C (T90-0800-15): C2 Knob (VOLUME) 旋钮(音量) (K29-9309-03) Knob (PTT) 按钮(PTT) (K29-9308-03) Cabinet assy 机壳 (A02-3851-23) Knob (CH-SELECTOR) 旋钮(信道) (K29-931

2、8-03) GENERAL .2 SYSTEM SET-UP .3 REALIGNMENT.4 DISASSEMBLY FOR REPAIR .7 CIRCUIT DESCRIPTION .12 TERMINAL FUNCTION.20 SEMICONDUCTOR DATA .20 COMPONENTS DESCRIPTION .22 PARTS LIST.24 EXPLODED VIEW.30 PACKING .31 ADJUSTMENT .32 PC BOARD TX-RX UNIT (X57-6890-XX).44 SCHEMATIC DIAGRAM.48 BLOCK DIAGRAM.5

3、2 LEVEL DIAGRAM.54 KSC-31 / KNB-29N.55 KNB-30A / KBH-10.56 SPECIFICATIONS.57 CONTENTS TK-3207 2 INTRODUCTION SCOPE OF THIS MANUAL This manual is intended for use by experienced technicians familiar with similar types of commercial grade communications equipment. It contains all required service info

4、rmation for the equipment and is current as of the publication date. Changes which may occur after publication are covered by either Service Bulletins or Manual Revisions. These are issued as required. ORDERING REPLACEMENT PARTS When ordering replacement parts or equipment information, the full part

5、 identification number should be included. This applies to all parts : components, kits, or chassis. If the part number is not known, include the chassis or kit number of which it is a part, and a sufficient description of the required component for proper identification. PERSONNEL SAFETY The follow

6、ing precautions are recommended for personnel safety: DO NOT transmit until all RF connectors are verified secure and any open connectors are properly terminated. SHUT OFF and DO NOT operate this equipment near electrical blasting caps or in an explosive atmosphere. This equipment should be serviced

7、 by a qualified technician only. 概述. 2 系统体系 . 3 模式组合 . 4 维修拆卸 . 7 电路说明 . 12 端子功能 . 20 半导体数据. 20 元件说明 . 22 零件表 . 24 部件分解图. 30 包装. 31 调整. 32 PC 板 TXRX 单元 (X57-6890-XX). 44 原理图 . 48 方块图 . 52 电平图 . 54 KSC-31 / KNB-29N . 55 KNB-30A / KBH-10 . 56 规格.封底 目录目录目录目录目录 GENERAL / 概述 引言 本手册的范围 本手册是提供给熟悉通信专业并且具有维修

8、经验的技术人员 使用的。它包括了维修该设备所需要的全部资料和现行出版日 期。在出版后如果发生变动、则根据需要使用维修通报或 手册修订本进行补充。 个人安全 为了个人的安全、请注意下列事项 在没有认真核实所有射频插头之前或有任何一个打开的插头 没有连接到相应端子上的情况下、均不要发射。 在电爆管附近或在易燃性气体环境中、必须关掉电源、不要 操作本设备。 本设备只应该由有资格的技术人员来维修。 替换零件的订购 当订购替换零件或设备资料时、 应注明完整的零件识别号码。 所有的零件均有识别号码元件、组件或机壳。如果不知道零 件的号码、为了正确地识别、必须注明此元件所属的机壳或组 件的号码、并对元件进行

9、充分的说明。 TK-3207 3 SYSTEM SET-UP / 系统体系 SYSTEM SET-UP / 系统体系 维修服务 为了便于维修本设备、建立了完整的维修服务体系、提供了 包括原理图、印刷线路板图和调整步骤在内的资料供参考。 Merchandise received Choose the type of transceiver Transceiver programming TX/RX TX/RX TX/RX 4.0W 4.0W 4.0W TK-3207 (M) TK-3207 (C) TK-3207 (C2) Frequency range (MHz)RF powerType 45

10、0490 440480 400430 A personal computer (IBM PC or compatible), programming interface (KPG-22), and programming software (KPG-87D) are required for programming. (The frequency, TX power HI/LOW, and signalling data are programmed for the transceiver.) 编程时需要个人计算机(IBM计算机或兼容机)，编程接口(KPG-22) 和编程软件 (KPG-87D

11、)。 (为手持机设定频率，常规系统特性，TX高/低功率， 以及信令数据。) 接收订单 选择手持机的类型 手持机编程 Are you using the optional antenna?KRA-23 or KRA-27 optional antenna YES / 是 NO / 不 您使用可选件天线吗?KRA-23 或 KRA-27 可选件天线 Delivery Are you using the speaker microphone?KMC-17 or KMC-21 Speaker microphone YES / 是 NO / 不( Option / 可选件 ) 您使用扬声器话筒吗?KMC

12、-17或KMC-21 扬声器话筒 频率范围（MHz） 射频功率 类型 交货 GENERAL / 概述 SERVICE This radio is designed for easy servicing. Refer to the schematic diagrams, printed circuit board views, and alignment procedures contained within. Unit ModelTX-RX UnitFrequency rangeRemarks & destination MX57-6890-20450490MHz TK-3207CX57-68

13、90-21440480MHz IF1 : 38.85MHz LOC : 38.4MHz C2X57-6890-22400430MHz 单元 TX-RX 单元频率范围备注 型号和类型 MX57-6890-20450490MHz TK-3207CX57-6890-21440480MHz IF1 : 38.85MHz LOC : 38.4MHz C2X57-6890-22400430MHz TK-3207 4 模式功能 用户模式一般使用 计算机模式用户手持机与计算机(IBM 兼容机)之 间的通信。 数据编程模式用于读出和写入频率数据以及其他功 能。 计算机测试模式用于使用计算机来检测手持机。此功 能

14、包括在KPG- 87D内。 复制模式用于从一个手持机编程数据复制到另 一个手持机。 REALIGNMENT / 模式组合 3-3. KPG-22 description (PC programming interface cable: Option) The KPG-22 is required to interface the TK-3207 with the computer. It has a circuit in its D-subconnector (25-pin) case that converts the RS-232C logic level to the TTL level

15、. 模式组合 1 . 模式 用户模式 计算机模式 计算机测试模式 数据编程模式 计算机调谐模式 3. 计算机模式 3-1 前言 TK-3207 手持机使用计算机、编程接口（KPG-22）和编程软 件（KPG-87D）进行编程。 IBM 计算机或兼容机可以使用编程软件。图1显示IBM 计算 机编程的设置。 3-2 连接步骤 1. 使用接口电缆将 TK-3207连接到计算机上。 2. 当电源接通时，立即进入用户模式。当 PC 机发出指令时， 手持机进入PC模式。 当手持机传送数据时，红色指示灯闪动。 当手持机传送数据时，绿色指示灯闪动。 3-3 KPG-22说明(PC机编程接口电缆可选件) TK-

16、3207需要通过接口电缆KPG-22与电脑连接。此接口电缆 的D连接器（25芯）中有一个将RS-232C逻辑电平转换为TTL 电平的电路。 KPG-22连接TK-3207的侧面插孔，然后连接到电子计算机的 注释： 当把储存在计算机中的数据写入到EEPROM中时,机型型号 必须相匹配。 将TK-3207改变为计算机模式，然后连接接口电缆。 1. Modes REALIGNMENT 3. PC Mode 3-1. Preface The TK-3207 transceiver is programmed using a personal computer, a programming interf

17、ace (KPG-22) and programming software (KPG-87D). The programming software can be used with an IBM PC or compatible. Figure 1 shows the setup of an IBM PC for programming. 3-2. Connection procedure 1. Connect the TK-3207 to the personal computer with the interface cable. 2. When the POWER is switched

18、 on, user mode can be entered immediately. When the PC sends a command, the radio enters PC mode. When data is transmitting from the transceiver, the red LED lights. When data is received by the transceiver, the green LED lights. Notes: The data stored in the personal computer must match the model t

19、ype when it is written into the EEPROM. Change the TK-3207 to PC mode, then attach the interface cable. 2. How to Enter Each Mode ModeOperation User modePower ON PC modeReceived commands from PC Clone modePTT+Side2+Power ON (Two seconds) 2. 如何进入每一种模式 模式操作 用户模式接通电源 计算机模式从计算机接收指令 复制模式PTT+侧面 2+接通电源（2 秒

20、钟） ModeFunction User modeFor normal use. PC modeUsed for communication between the radio and PC (IBM compatible). Data programmingUsed to read and write frequency data modeand other features to and from the radio. PC test modeUsed to check the radio using the PC. This feature is included in the KPG-

21、 87D. Clone modeUsed to transfer programming data from one radio to another. User mode PC mode PC test mode Data programming mode PC tuning mode Clone mode复制模式 TK-3207 5 Fig. 1 / 图 Tuning cable / 调谐电缆 (E30-3216-05) RF Power meter or SSG / RF功率表或SSG KPG-22 KPG-87D IBM-PC / IBM计算机 灰色 灰色/黑色 1.5D-XV 导线

22、1.5D-XV 屏蔽线 SP MIC Gray Gray/Black 1.5D-XV Lead wire 1.5D-XV Shield wire REALIGNMENT / 模式组合 4. Clone Mode 4-1. Outline Clone Mode copies the transceiver data to another transceiver. The dealer can copy the transceiver data to another transceiver even without the use of a personal computer. 4-2. Exam

23、ple The transceiver can copy the programming data to one or more transceivers via RF communication. The clone master and clone slave/s must be in Clone mode. 4-3. Operation 1. To switch the clone slave/s to Clone mode, press and hold the PTT and side2 keys while turning the transceiver power ON. 2.

24、Wait for 2 seconds. The LED will light orange and the transceiver will announce Clone. 3. Select a channel table number using Side1(increment channel table) and Side2(decrement channnel table) keys. 4. To switch the clone master to Clone mode, press and hold the PTT and side2 keys while turning the

25、transceiver power ON. 5. Wait for 2 seconds. The LED will light orange and the transceiver will announce Clone. 6.Select the same channel table number as the clone slave/s. 7. Press PTT on the clone master to begin data transmission. When the clone slave starts to receive data, the LED will light gr

26、een. When the clone master finishes sending data, a confirmation tone will sound. If data transmission fails while cloning, an error tone will sound from the Slave unit. 4. 复制模式 4-1 概要 “复制模式”可以将一台手持机的数据复制到其它的手持机。 经销商甚至不使用个人电脑也可以将一台手持机的数据复制 到其它的手持机。 4-2 例: 手持机可以通过 RF 通信复制编程数据到一台或更多的手持 机。 复制主机和复制子机必须觧

27、于复制模式。 4-3 操作方法 1. 将子机切换到复制模式，旋转手持机电源的同时，持续按 PTT 键和 侧2 键。 2. 等待2秒。 LED将呈橘黄色并且手持机将发出复制的声音。 3. 用侧 1 (频道表递增) 键和侧 2 (频道表递减) 键选择频道表号 码。 4. 将主机切换到复制模式，旋转手持机电源的同时，持续按 PTT 键和 侧2 键。 5. 等待2秒。 LED将呈橘黄色并且手持机将发出复制的声音。 6. 选择与复制子机相同的频道表号码。 7. 按复制主机上的 PTT，开始数据传输。 当复制子机开始接收数据时，LED 将呈绿色。 当复制主机完成传送数据时，将发出一个“确认”音。 如果在复

28、制过程中数据传输失败， 子机将发出一个错误音。 8. 如果复制失败，子机回到用户模式时数据随即消失。 9. 当复制成功时，子机的扫描和键锁定功能将回到它们 的初始值 (扫描=OFF, 键锁定=OFF) The KPG-22 connects the side panel connector of the TK- 3207 to the computers RS-232C serial port. 3-4. Programming software description KPG-87D is the programming software for TK-3207 supplied on a

29、CD-ROM. This software runs under Windows 98, ME, Windows 2000 or XP on an IBM-PC or compatible machine. The data can be input to or read from TK-3207 and edited on the screen. The programmed or edited data can be printed out. It is also possible to tune the transceiver. RS-232C 串行接口。 3-4 编程软件说明 KPG-

30、87D 是手持机 TK-3207 的编程软件。此软件的运行环境 为IBM-PC 机或兼容机的Windows 98,ME,Windows 2000或XP。 数据可以被输入到 TK-3207 手持机或从手持机中读取数据， 并且在屏幕上进行编辑。 已被编程或编辑的数据可以打印出来。 也可以调整手持机的指标。 TK-3207 6 8. If the cloning fails, no data will be available in the Slave unit when it is returned to User mode. 9. When the cloning is successful,

31、the Slave units Scan and Key lock functions will return to their default values (Scan = OFF, Key lock = OFF). Notes: The dealer can clone data to two or more transceivers by repeating the above procedures. If the transceivers Clone Mode is configured as Disabled, the transceiver cannot enter Clone m

32、ode. The table shown below will cover the frequency tables used for wireless cloning. Clone mode cannot be entered in battery low state. A unit cannot be a Master Unit if it is unprogrammed. If PTT is pressed, an error tone will sound. The language used in cloning depends on the Model type setting,

33、not the FPU setting. C, C2, C5 and C6 type TK-3207 transceivers will use Chinese. Other types English. Once a unit is set to be the Master, it cannot be a slave after the data has been transmitted. This protects the data in the Master unit. Electronic interface may cause a failure in data transfer d

34、uring Wireless Clone, such as when waveforms or electromagnetics are being performed at the workbench. Clone mode can be used ONLY by the authorized service personnel. The Clone mode setting must be configured as Disable before being delivered to the end-user. To clone, replace the antenna from both

35、 the master transceiver and the slave transceiver with a dummy load. The transmit output power is automatically set to Low in Clone mode. 1450.000440.000400.000 2452.000442.000401.000 3454.000446.000402.000 4456.000448.000403.000 5458.000450.000404.000 6460.000452.000405.000 7462.000454.000406.000 8

36、464.000456.000407.000 9466.000458.000408.000 10468.000460.000409.000 11470.000462.000410.000 12472.000464.000411.000 13474.000466.000412.000 14476.000468.000413.000 15478.000470.000414.000 16480.000472.000415.000 17482.000474.000416.000 18484.000476.000417.000 19486.000478.000418.000 20488.000480.00

37、0419.000 Clone Frequency Table TypeMCC2 Operating CloneFrequency 450490440480400430 Frequency(MHz) Table 1450.000440.000400.000 2452.000442.000401.000 3454.000446.000402.000 4456.000448.000403.000 5458.000450.000404.000 6460.000452.000405.000 7462.000454.000406.000 8464.000456.000407.000 9466.000458

38、.000408.000 10468.000460.000409.000 11470.000462.000410.000 12472.000464.000411.000 13474.000466.000412.000 14476.000468.000413.000 15478.000470.000414.000 16480.000472.000415.000 17482.000474.000416.000 18484.000476.000417.000 19486.000478.000418.000 20488.000480.000419.000 复制频率表 类型MCC2 操作频率 (MHz)

39、450490440480400430 复制频率表 REALIGNMENT / 模式组合 注释： 经销商可以反复上述过程复制数据到2个或更多的手持机。 如果手持机复制模式被设置为“无效” ，则手持机不能进入 复制模式。 下表包含了无线复制用的频率表。 当电池觧于低电压状态时不能进入复制模式。 如果手持机是非编程的它将不能成为主机。 如果按PTT， 将 发出一个错误 音。 复制时所用的语言是根据样机类别设置，而不是FPU设 置，TK-3207的C，C2， C5和C6 类别的手持机用中文，其它 类别用英文。 手持机一旦被设置为主机， 数据传送以后， 它就不能成为子 机。这是为了保护主机里的数据。 在

40、无线复制的数据传输过程中， 例如在工作台产生的电波或 电磁干扰有可能引起传输失败。 复制模式可以仅被批准的服务人员使用。 在交付给最终用户之前，复制模式设置必须被设置为“无 效” 。 为了复制，将模拟负载代替主手持机和子手持机的天线。 在复制模式，发射功率自动设定为低。 TK-3207 7 DISASSEMBLY FOR REPAIR / 维修拆卸 Removing the case assembly from the chassis. 1. Remove the volume knob z and channel knob x. 2. Remove the two screws c. 3.

41、Lift and remove the chassis from the case assembly v. (Use a flat-blade screwdriver to easily lift the chassis.) Removing the TX-RX unit from the chassis. 1. Remove the packing b from the SP / MIC jack of the TX- RX unit. 2. Remove the eleven screws n fixing the TX-RX unit. 3. Remove the fixing brac

42、ket m of the SP / MIC. 4. Remove the solder of the antenna terminal with a soldering iron ,. 5. Remove the solder of the positive terminal with a soldering iron . Note: You can remove the TX-RX unit from the chassis without removing the solder at the positive terminal. However, in this case, you can not attach t