Sangean_ATS-505_user.pdf

《Sangean_ATS-505_user.pdf》由会员分享，可在线阅读，更多相关《Sangean_ATS-505_user.pdf（14页珍藏版）》请在收音机爱好者资料库上搜索。

1、ATS-505 Version 1 GB Control Locations Power/Sleep Power On/off/Alarm off/sleep function Display Switch between radio frequency and time while radio is power on Mode Mode set up (please see below mode button set up) Radio alarm Buzzer alarm Tuning Up/Down Enter command button for frequency and time

2、set Selection cancel Numbered buttons and memory scan (the 0 Button) Memory set buttons and AM/PM selection for 24-hour format Real/dual time button and SW memory page SW meter band selection Band selection Tuning LED indicator (Green)/SSB on (Red) Display (L .C.D.) Display illuminated button (Light

3、) Clarify SSB fine tune External Short Wave antenna jack DX/Local switch FM Mono/Stereo.SSB/AM switch Earphones socket DC input socket Rotary tuning knob /Fine tuning Music/Normal /News Tone control LICK switch Volume control Reset Telescopic Antenna Battery compartment Folding stand Display informa

4、tion FM stereo indication Sleep (auto shut off)status Lock on Buzzer alarm set Radio alarm set Tuning step Short wave meter band kHz for MW, LW, SW and MHz for FM band Short Wave Broadcast bandLow battery indicator Memory bar Frequency and Time display Memory Page 1/2 Radio band and AM/PM (for 12 ho

5、urs format )indicator Real/Dual time 1.Position the radio face down 2.Press the catch marked and slide in the direction shown. 3.Insert the 4 UM-2 (LR6)(AA size) batteries. 4. Replace the battery cover. Choosing a power supply Installing batteries Battery replacement Low battery warnings Using the A

6、C adapter Setting the clock This radio can be operated using. 4 Alkaline UM-3(LR6)(AA size)batteries. Household AC adapter(not supplied). The battery indicator will display the battery condition for approx.7 seconds after the radio is switched off. If the battery strength indicator is shown below2.t

7、he batteries Should be replaced. After removing the batteries you have approx.3 minutes to replace the batteries after which clock and memory information will be lost. 1.Replace batteries if display flashes . 2.Replace batteries if press power button, the radio still not operate. Insert the adapter

8、plug into the socket 6V DC on the left side of the radio. Plug the adapter into a standard mains socket outlet. Whenever the adapter is used, the batteries are automatically disconnected. The mains adapter should be disconnected from the mains supply when not in use for long time. We would recommend

9、 that the receiver operates via the AC adapter whenever possible, add with battery operation for occasional or stand-by use only. The clock will start running when the batteries are installed or the adapter is plugged in. The display will show 0:00 or AM 12:00 and real time icon. The real time can b

10、e set. 1. When the radio is switched off 2. If the radio switched on, press DISPLAY button to time status. 3. Press ENTER button for more than 2 seconds until real time symbol and 4. Set the correct time by pressing the numbered buttons. As you press each button, the corresponding number will show o

11、n the display. 5. If you press wrong button, after pressing the ENTER button. The radio will beep and Err flashed in the display. 6. Press Enter button again to complete the clock setting. Note: You may change 24 hour to 12 hour format or vice versa by pressing MODE and related buttons described lat

12、er. In addition to real time, a dual time can be programmed into the radio. 1. Press Real/Dual time button, the Dual time symbol will flash. 2. Press ENTER button, display dual time symbol will stop flashing. 3. Press ENTER button again for more than 2 seconds until dual time symbol flashes, set the

13、 dual time by pressing the numbered buttons. 4. The rest of the operation is same as setting the real time. Note: a. To temporarily change between real and dual time mode, press Real/dual time button. The dual time icon and dual time will be shown in the display. After approx. 7 seconds, the display

14、 will return to show real time. b. To permanently change the display to dual time, press Real/Dual time button followed by the ENTER button. Dual time icon will appear on the display. C. To permanently change the display back to real time mode, press Real/Dual time button followed by the ENTER butto

15、n. The will be removed from display. Setting the dual time 4 5 Waveband selection Direct tuning Manual tuning by tuning UP/DOWN button There are four waveband selection by pressing BAND button Waveband Frequency coverage Aerial Type - FM 87.50- 108 MHz Telescopic Full extend the aerial, angle and ro

16、tate for best reception. MW 520- 1710 kHz Internal SW 1711- 29999 kHz Telescopic Fully extend the aerial for best reception. LW 153- 279kHz Internal Stations may be selected by using any of the five different available tuning methods: Direct Tuning, Manual tuning, Scan tuning, Memory Recall Tuning a

17、nd APS on MW. FM and LW bands. Example : To tune to 100.70 MHz on the FM band. 1.Press the POWER on/off button to turn on the radio. 2.Select the required FM band by pressing BAND button. 3.Press ENTER - Freq./time Set button, display shows 4.Press the numbered buttons marked1,0,07., then press ENTE

18、R button again, the frequency will now appear in the display. Note: There is no decimal point, therefore you press the number button, make sure you have selected the required waveband, otherwise the operation may switch to other waveband. 5.Extend the aerial fully and rotate for best FM reception. 6

19、.Adjust the volume control for comfortable listening. 7.When selecting a stereo FM station and using stereo earphones, make sure the FM mode switch is in the stereo position. 1.Press the POWER on/off button to turn on the radio. 2. Select a waveband by pressing BAND button. 3.A single press on eithe

20、r Tuning UP or Down button will change the frequency up or down. 6 Note: Each press of Up or Down button will change the frequency in increment of FM: 100kHz or 200kHz depending on the versions. MW: 9kHz or 10kHz depending on the versions. SW: 5kHz LW: 9kHz Rotary tuning is accomplished using the co

21、nvenient Rotary Tuning Knob. Original tuning step is as below but can be changed by the MODE button as described later. BAND FM MW LW SW Step 100 or 200 kHz 9kHz or 10 kHz 9 kHz 5 kHz Fine Tune 50 kHz 1 kHz 1 kHz 1 kHz Note: Fine tune can be op erated by pressing the rotary tuning knob in. Display w

22、ill show fine tune step then the last frequency tuned. Note: During fine tune operation, any press to other functional buttons will cause Fine Tune back to normal tune. 1.Turn on the radio by pressing the POWER on/off button. 2.Select a waveband. 3.Press and hold down either the tuning UP or DOWN bu

23、tton for more than half a second to commence scan tuning. The radio will scan all frequencies in the selected band and stop automatically each time it finds an active station. 4.Press and hold down either the tuning UP or DOWN buttons for more than half a second to resume scan tuning. When the waveb

24、and end is reached, the radio will beep and continue tuning from the opposite waveband end. 5.Adjust the volume control for comfortable listening. You may store up to 45 preset stations in memory. 18 on SW in 2 pages, 9 each on FM, MW and LW bands. To store a station in preset memory, proceed as fol

25、lows. 1.Turn on the radio by pressing the POWER on/off button. 2.Tune to the desired frequency using one of the previous described tuning methods. Manual tuning by Rotary tuning knob Scan tuning Memory tuning 3.Press the button marked M (memory), display M and suggested preset number will flash, pre

26、ss ENTER to store your station in that memory position. 4.Preset positions may be exchanged easily. Select preset station that is to be changed, press memory button ( M and existing memory position will flash). select new preset position. Preset will be exchanged automatically. 5.SW band has 18 pres

27、ets (in two pages).When presets 1-9 are full, press PAGE button to select Page 2. Display will show M2. and an additional 1-9 presets can be set for a total of 18 presets. Note: 1. If all presets have been used, pushing M button will display FULL on LCD. If you still desire to store new station, pus

28、h any button of 1-9 where new station is to be stored and hold for more than 2 seconds. New station will be put into memory in position selected and original station in this position will be replaced. 2. All preset stations are indicated by on the display. If a station has already 1. Turn on the rad

29、io by pressing the POWER on/off button. 2. Select the waveband for the station required. 3. Press the numbered button corresponding to the preset memory location for the required station. The radio will instantly tune to the station and display will show its frequency and memory location. 1.Turn on

30、the radio by pressing the POWER on/of button. 2.Press BAND button to select the SW waveband. 3.Press SW SELECT button to select the required SW meter band, display will appear low end frequency and SW meter band it belongs to. This radio covers SW 120 to 11 meter band. This radio provides an easy to

31、 use feature called APS (Auto Preset System) which operated on FM, MW and LW bands. 1.Turn on the radio by pressing POWER on/off button. 2.Press BAND button to select the required waveband. been put into the memory. it will show preset position on display. Recalling a station Select Short Wave Meter

32、 Band APS (auto Preset System) 7 3.Press Tuning UP and DOWN button at the same time for more than 2 seconds. The radio will beep and then scan from the lowest frequency on the selected band. Automatically storing stations in preset memory based on signal strength. 4.After APS is completed, a beep wi

33、ll be heard. The display will show M1 and the strongest station for your area. 5.If during APS operation, no stations are found, display will show lowest frequency of selected band. Note: 1.The maximum number of preset is 9 each on FM/MW/LW bands. If during APS operation more than 9 presets are foun

34、d, there will be only 9 stations stored in the preset memories. 2.The SW band has no APS function. 3.All previous stored preset stations will be erased when APS operation commences. 4.APS operation can be cancelled by pressing the POWER on/off This radio provides a feature called Memory Scan, when a

35、ctivated will scan the Preset memories. 1.Turn on the radio by pressing the POWEN button. Select the required waveband. 2.Press the M.SCAN button, the radio will scan each preset memory in turn-pause for 7 seconds on each memory before continuing on to the next memory. When the required preset is re

36、ached, press any button to stop memory scan. The alarm can beset with the radio power on or off. If the radio is switched on, press DISPLAY button display the time. 1.Press RADIO ALARM button , display radio alarm icon will flash and show the last alarm time set. Press the number buttons then ENTER

37、to set RADIO alarm time. 2.To verify the alarm time, Press RADIO ALARM button to display the alarm time followed by ENTER button to return to real time mode. 3.To cancel radio alarm set, press RADIO ALARM button, display will show previous alarm set status then press C (Cancel) to cancel radio alarm

38、 set. Display alarm icon will disappear. Memory Scan Setting the alarm (standby) Setting Radio Alarm 8 Note: 1.When alarm is on, press POWER button to turn off the alarm for 24 hours. 2.Radio alarm on will last for one hour if not turned off by pushing the POWER button. 3.Turn the radio to the requi

39、red station before setting the radio alarm. When the alarm is on, the radio will play last station selected. A repeating beep tone will sound when using the HWS alarm. The alarm beep will increase in volume every 15 seconds for one minute followed by 1 minute silence before repeating the cycle. The

40、HWS alarm will last for one hour unless turn off by pushing the POWER button. 1.The HWS alarm is set in the same way as the radio alarm except pushing HWS alarm button And display sill appear 2.The HWS alarm can be turned off by pressing the POWER button. 3.To cancel HWS alarm set, follow the way to

41、 cancel Radio alarm. The sleep timer will automatically switch off radio after a preset time has elapsed. 1.Press and continue to hold down the POWER/SLEEP button, the display will cycle through available sleep time 60-30-15-120-90-60. Release the SLEEP button when the required sleep time appears in

42、 the display. The SLEEP symbol together with frequency will appear in the display. After 2 seconds, display will be back to display frequency. 2.To cancel the sleep function, press the POWER button, the SLEEP symbol will disappear and the display will revert to show real time and radio will be off.

43、To meet different requirements from various markets, you may change the initial Setting by pressing MODE and related numbered buttons described as below. Setting the HWS (Humane Wake System) alarm Setting the sleep timer MODE button sep up 9 10 Numbered key 8 key 1 key 1 FM 100kHz FM 200 kHz tuning

44、step tuning step 2. MW 9 kHz MW 10 kHz 3 12 hour format 24 hour format 4 Beep tone off Beep tone on 5 Memory Rearranged Complete with ENTER button For example, if you like to change from MW 10 kHz to 9 kHz, press MODE, numbered button 2 , 0 , then complete with ENTER button. You can rearrange your m

45、emory stations from low frequency to high frequency by Pressing MODE, numbered button 5, 0 or 5, 1 then complete with(ENTER) button. Some SW and LW stations transmit in Morse Code using a form of transmission Called continuous wave (CW). Some SW stations use a special type voice transmission called

46、single side band (SSB). To tune to a CW or SSB station, select the band and frequency and adjust the antenna. In addition, switch the SSB switch to SSB position, Tuning/SSB LED will be on Red. Then beginning at its midpoint, slowly adjust the CLARIFY dial until reception becomes clear. You may at th

47、e same time use the rotary FINE tuning for best SSB reception. When a station is found, the Tuning/SSB LED will become in orange CLARIFY tuning range can be + 1.5kHz SSB (single side band)/Clarify(+,-) FM Mono/Stereo Headphones (or earphones) Lock switch Light DX/Local switch SW EXT. ANT To listen to FM stereo broadcasts, tune to the required station, plug in headphones and set the FM ST./MO. Switch located on the left side of the radio to to FM ST. (stereo)