《FLUKE 8845A___sseng0000 电路图.pdf》由会员分享，可在线阅读，更多相关《FLUKE 8845A___sseng0000 电路图.pdf（2页珍藏版）》请在收音机爱好者资料库上搜索。
1、 8845A/8846A Digital Multimeters Safety Information Safety Information This safety information should be observed when using the 8845A or 8846A (hereafter the Meter) Digital Multimeters. A XWWarning statement identifies conditions or practices that could result in injury or death. A W Caution statem
2、ent identifies conditions or practices that could result in damage to the Meter or equipment to which it is connected. XW Warning To avoid electric shock, personal injury, or death, carefully read the information in this safety sheet before attempting to install, use, or service the Meter. Symbols T
3、able 1 is a list of safety and electrical symbols that appear on the Meter or in its manuals. Table 1. Safety and Electrical Symbols Symbol Description Symbol Description W Risk of danger. Important information. See manual O Display ON / OFF X Hazardous voltage. Voltage 30 V dc or ac peak might be p
4、resent J Earth ground B AC (Alternating Current) E Capacitance F DC (Direct Current) G Diode I Fuse D or C AC or DC (Alternating or Direct Current) Y Digital signal R Continuity test or continuity beeper tone U Maintenance or Service Y Potentially hazardous voltage CAT II IEC 61010 Overvoltage (inst
5、allation or measurement) Category 2. T Double insulated Recycle h Static awareness. Static discharge can damage part(s) Do not dispose of this product as unsorted municipal waste. Contact Fluke or a qualified recycler for disposal PN 2741870 August 2006 2006 Fluke Corporation. All rights reserved. P
6、rinted in U.S.A. 1 RadioFans.CN 收音机爱 好者资料库 8845A/8846A Safety Information 2 XW Warning To avoid possible electric shock, personal injury, or death, read the following before using the Meter: Use the Meter only as specified in the Users Manual, or the protection provided by the Meter might be impaire
7、d. Do not use the Meter in wet environments. Inspect the Meter before using it. Do not use the Meter if it appears damaged. Inspect the test leads before use. Do not use them if insulation is damaged or metal is exposed. Check the test leads for continuity. Replace damaged test leads before using th
8、e Meter. Verify the Meters operation by measuring a known voltage before and after using it. Do not use the Meter if it operates abnormally. Protection may be impaired. If in doubt, have the Meter serviced. Whenever it is likely that safety protection has been impaired, make the Meter inoperative an
9、d secure it against any unintended operation. Have the Meter serviced only by qualified service personnel. Do not apply more than the rated voltage, as marked on the Meter, between the terminals or between any terminal and earth ground. Always use the power cord and connector appropriate for the vol
10、tage and outlet of the country or location in which you are working. Remove test leads from the Meter before opening the case. Never remove the cover or open the case of the Meter without first removing it from the main power source. Never operate the Meter with the cover removed or the case open. U
11、se caution when working with voltages above 30 V ac rms, 42 V ac peak, or 42 V dc. These voltages pose a shock hazard. Use only the replacement fuse(s) specified by the Users Manual. Use the proper terminals, function, and range for your measurements. Do not operate the Meter around explosive gas, v
12、apor, or dust. When using probes, keep your fingers behind the finger guards. When making electrical connections, connect the common test lead before connecting the live test lead; when disconnecting, disconnect the live test lead before disconnecting the common test lead. Disconnect circuit power a
13、nd discharge all high-voltage capacitors before testing resistance, continuity, diodes, or capacitance. Before measuring current, check the Meters fuses and turn OFF power to the circuit before connecting the Meter to the circuit. When servicing the Meter, use only spedified replacement parts. RadioFans.CN 收音机爱 好者资料库
免费区 
