KEI 6517A Getting Started Guide 电路图.pdf

《KEI 6517A Getting Started Guide 电路图.pdf》由会员分享，可在线阅读，更多相关《KEI 6517A Getting Started Guide 电路图.pdf（110页珍藏版）》请在收音机爱好者资料库上搜索。

1、 Contains Operating Information Model 6517A Electrometer/High Resistance Meter Getting Started Manual RadioFans.CN 收音机爱 好者资料库 WARRANTY Keithley Instruments, Inc. warrants this product to be free from defects in material and workmanship for a period of 1 year from date of shipment. Keithley Instrumen

2、ts, Inc. warrants the following items for 90 days from the date of shipment: probes, cables, rechargeable batteries, diskettes, and documentation. During the warranty period, we will, at our option, either repair or replace any product that proves to be defec- tive. To exercise this warranty, write

3、or call your local Keithley representative, or contact Keithley headquarters in Cleveland, Ohio. You will be given prompt assistance and return instructions. Send the product, transportation prepaid, to the indicated service facility. Repairs will be made and the product returned, transportation pre

4、paid. Repaired or replaced products are warranted for the balance of the original warranty period, or at least 90 days. LIMITATION OF WARRANTY This warranty does not apply to defects resulting from product modifi cation without Keithleys express written consent, or misuse of any product or part. Thi

5、s warranty also does not apply to fuses, software, non-recharge- able batteries, damage from battery leakage, or problems arising from normal wear or failure to follow instruc- tions. THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUD- ING ANY IMPLIED WARRANTY OF MERCHANT

6、ABILITY OR FITNESS FOR A PARTICULAR USE. THE REMEDIES PROVIDED HEREIN ARE BUYERS SOLE AND EXCLUSIVE REMEDIES. NEITHER KEITHLEY INSTRUMENTS, INC. NOR ANY OF ITS EMPLOYEES SHALL BE LIABLE FOR ANY DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF ITS INSTRUMENTS A

7、ND SOFTWARE EVEN IF KEITHLEY INSTRUMENTS, INC., HAS BEEN ADVISED IN ADVANCE OF THE POSSIBILITY OF SUCH DAMAGES. SUCH EXCLUDED DAM- AGES SHALL INCLUDE, BUT ARE NOT LIMITED TO: COSTS OF REMOVAL AND INSTALLATION, LOSSES SUSTAINED AS THE RESULT OF INJURY TO ANY PERSON, OR DAMAGE TO PROPERTY. BELGIUM:Kei

8、thley Instruments B.V. Bergensesteenweg 709 B-1600 Sint-Pieters-Leeuw 02/363 00 40 Fax: 02/363 00 64 CHINA:Keithley Instruments China Yuan Chen Xin Building, Room 705 12 Yumin Road, Dewai, Madian Beijing 100029 8610-62022886 Fax: 8610-62022892 FRANCE:Keithley Instruments Sarl B.P. 60 3, alle des Gar

9、ays 91122 Palaiseau Cdex 01 64 53 20 20 Fax: 01 60 11 77 26 GERMANY:Keithley Instruments GmbH Landsberger Strasse 65 D-82110 Germering 089/84 93 07-40 Fax: 089/84 93 07-34 GREAT BRITAIN: Keithley Instruments Ltd The Minster 58 Portman Road Reading, Berkshire RG30 1EA 0118-9 57 56 66 Fax: 0118-9 59 6

10、4 69 INDIA:Keithley Instruments GmbH Flat 2B, WILOCRISSA 14, Rest House Crescent Bangalore 560 001 91-80-509-1320/21 Fax: 91-80-509-1322 ITALY:Keithley Instruments s.r.l. Viale S. Gimignano, 38 20146 Milano 02/48 30 30 08 Fax: 02/48 30 22 74 NETHERLANDS:Keithley Instruments B.V. Postbus 559 4200 AN

11、Gorinchem 0183-635333 Fax: 0183-630821 SWITZERLAND:Keithley Instruments SA Kriesbachstrasse 4 8600 Dbendorf 01-821 94 44 Fax: 01-820 30 81 TAIWAN:Keithley Instruments Taiwan 1 Fl. 85 Po Ai Street Hsinchu, Taiwan, R.O.C. 886-3572-9077 Fax: 886-3572-9031 10/99 Keithley Instruments, Inc. 28775 Aurora R

12、oad Cleveland, OH 44139 440-248-0400 Fax: 440-248-6168 RadioFans.CN 收音机爱 好者资料库 Model 6517A Electrometer/ High Resistance Meter Getting Started Manual 1995, Keithley Instruments, Inc. All rights reserved. Cleveland, Ohio, U.S.A. First Printing, July 2000 Document Number: 6517A-903-01 Rev. A All refer

13、ences to the Model 6517 also apply to the Model 6517A. RadioFans.CN 收音机爱 好者资料库 Manual Print History The print history shown below lists the printing dates of all Revisions and Addenda created for this manual. The Revision Level letter increases alphabetically as the manual undergoes sub- sequent upd

14、ates. Addenda, which are released between Revisions, contain important change in- formation that the user should incorporate immediately into the manual. Addenda are numbered sequentially. When a new Revision is created, all Addenda associated with the previous Revision of the manual are incorporate

15、d into the new Revision of the manual. Each new Revision includes a revised copy of this print history page. Revision A (Document Number 6517A-903-01) .July 2000 All Keithley product names are trademarks or registered trademarks of Keithley Instruments, Inc. Other brand names are trademarks or regis

16、tered trademarks of their respective holders. Safety Precautions The following safety precautions should be observed before using this product and any associated in- strumentation. Although some instruments and accessories would normally be used with non-hazardous voltages, there are situations wher

17、e hazardous conditions may be present. This product is intended for use by qualifi ed personnel who recognize shock hazards and are familiar with the safety precautions required to avoid possible injury. Read the operating information carefully before using the product. The types of product users ar

18、e: Responsible body is the individual or group responsible for the use and maintenance of equipment, for ensuring that the equipment is operated within its specifi cations and operating limits, and for ensuring that operators are adequately trained. Operators use the product for its intended functio

19、n. They must be trained in electrical safety procedures and proper use of the instrument. They must be protected from electric shock and contact with hazardous live circuits. Maintenance personnel perform routine procedures on the product to keep it operating, for example, setting the line voltage o

20、r replacing consumable materials. Maintenance procedures are described in the manual. The procedures explicitly state if the operator may perform them. Otherwise, they should be performed only by service personnel. Service personnel are trained to work on live circuits, and perform safe installation

21、s and repairs of prod- ucts. Only properly trained service personnel may perform installation and service procedures. Exercise extreme caution when a shock hazard is present. Lethal voltage may be present on cable con- nector jacks or test fi xtures. The American National Standards Institute (ANSI)

22、states that a shock haz- ard exists when voltage levels greater than 30V RMS, 42.4V peak, or 60VDC are present. A good safety practice is to expect that hazardous voltage is present in any unknown cir- cuit before measuring. Users of this product must be protected from electric shock at all times. T

23、he responsible body must en- sure that users are prevented access and/or insulated from every connection point. In some cases, con- nections must be exposed to potential human contact. Product users in these circumstances must be trained to protect themselves from the risk of electric shock. If the

24、circuit is capable of operating at or above 1000 volts, no conductive part of the circuit may be exposed. As described in the International Electrotechnical Commission (IEC) Standard IEC 664, digital multi- meter measuring circuits (e.g., Keithley Models 175A, 199, 2000, 2001, 2002, and 2010) are In

25、stallation Category II. All other instruments signal terminals are Installation Category I and must not be connect- ed to mains. Do not connect switching cards directly to unlimited power circuits. They are intended to be used with impedance limited sources. NEVER connect switching cards directly to

26、 AC mains. When connecting sources to switching cards, install protective devices to limit fault current and voltage to the card. Before operating an instrument, make sure the line cord is connected to a properly grounded power re- ceptacle. Inspect the connecting cables, test leads, and jumpers for

27、 possible wear, cracks, or breaks be- fore each use. For maximum safety, do not touch the product, test cables, or any other instruments while power is ap- plied to the circuit under test. ALWAYS remove power from the entire test system and discharge any capacitors before: connecting or disconnectin

28、g cables or jumpers, installing or removing switching cards, or making internal changes, such as installing or removing jumpers. Do not touch any object that could provide a current path to the common side of the circuit under test or power line (earth) ground. Always make measurements with dry hand

29、s while standing on a dry, insulated surface ca- pable of withstanding the voltage being measured. The instrument and accessories must be used in accordance with its specifi cations and operating instructions or the safety of the equipment may be impaired. Do not exceed the maximum signal levels of

30、the instruments and accessories, as defi ned in the specifi cations and operating information, and as shown on the instrument or test fi xture panels, or switching card. When fuses are used in a product, replace with same type and rating for continued protection against fi re hazard. Chassis connect

31、ions must only be used as shield connections for measuring circuits, NOT as safety earth ground connections. If you are using a test fi xture, keep the lid closed while power is applied to the device under test. Safe operation requires the use of a lid interlock. If a screw is present, connect it to

32、 safety earth ground using the wire recommended in the user documen- tation. The symbol on an instrument indicates that the user should refer to the operating instructions located in the manual. The symbol on an instrument shows that it can source or measure 1000 volts or more, including the com- bi

33、ned effect of normal and common mode voltages. Use standard safety precautions to avoid personal contact with these voltages. The WARNING heading in a manual explains dangers that might result in personal injury or death. Always read the associated information very carefully before performing the in

34、dicated procedure. The CAUTION heading in a manual explains hazards that could damage the instrument. Such damage may invalidate the warranty. Instrumentation and accessories shall not be connected to humans. Before performing any maintenance, disconnect the line cord and all test cables. To maintai

35、n protection from electric shock and fi re, replacement components in mains circuits, including the power transformer, test leads, and input jacks, must be purchased from Keithley Instruments. Standard fuses, with applicable national safety approvals, may be used if the rating and type are the same.

36、 Other components that are not safety related may be purchased from other suppliers as long as they are equivalent to the original component. (Note that selected parts should be purchased only through Keithley Instruments to maintain ac- curacy and functionality of the product.) If you are unsure ab

37、out the applicability of a replacement component, call a Keithley Instruments offi ce for information. To clean an instrument, use a damp cloth or mild, water based cleaner. Clean the exterior of the instrument only. Do not apply cleaner directly to the instrument or allow liquids to enter or spill

38、on the instrument. Prod- ucts that consist of a circuit board with no case or chassis (e.g., data acquisition board for installation into a computer) should never require cleaning if handled according to instructions. If the board becomes contami- nated and operation is affected, the board should be

39、 returned to the factory for proper cleaning/servicing. ! Rev. 10/99 Table of Contents 1 Front Panel Operation Product overview.1-2 Display.1-8 Power-up.1-8 Bench defaults .1-9 Changing functions.1-9 Voltage measurements.1-10 Current measurements.1-12 Resistance measurements .1-13 Resistivity measur

40、ements .1-16 Charge measurements.1-18 External temperature and relative humidity measurements.1-20 2 Measurement Options Multiple displays .2-2 Menus .2-6 Voltage source.2-10 Relative.2-13 Zero check .2-14 Zero correct.2-14 Triggering .2-15 Speed.2-18 Resolution.2-19 Filter.2-20 Buffer (Data Store) .2-23 Math.2-24 Test sequences .2-27 Internal scanning.2-30 External scanning.2-32 3 Remote Operation Overview.3-2 Software support.3-3 IEEE-488 bus standards.3-4 RS-232 standard.3-4 IEEE-488 bus connections.3-4 RS-232 connections.