R&S ZVR, ZVRE, ZVRL, ZVC, ZVCE, ZVM, ZVK, Operating Vol 1 电路图.pdf_收音机爱好者资料库 www.radiofans.cn 提供大量国内外收音机电路图，根德grundig SABA 德律风根收音机电路图纸、原理图

资源描述

《R&S ZVR, ZVRE, ZVRL, ZVC, ZVCE, ZVM, ZVK, Operating Vol 1 电路图.pdf》由会员分享，可在线阅读，更多相关《R&S ZVR, ZVRE, ZVRL, ZVC, ZVCE, ZVM, ZVK, Operating Vol 1 电路图.pdf（502页珍藏版）》请在收音机爱好者资料库上搜索。

1、1127.8700.12-03- 1 Test and Measurement Division Operating Manual VECTOR NETWORK ANALYZER ZVR / ZVRE / ZVRL 1127.8551.61/.62 1127.8551.51/.52 1127.8551.41 ZVC / ZVCE 1127.8600.60/.61/.62 1127.8600.50/.51/.52 ZVM 1127.8500.60 ZVK 1127.8651.60 Volume 1 Operating Manual consists of 2 volumes Printed in

2、 the Federal Republic of Germany RadioFans.CN 收音机爱好者资料库 RadioFans.CN 收音机爱好者资料库 ZVxTabbed Divider Overview 1127.8700.12REE-1 Volume 1 Volume 2 ContentsContents IndexIndex Data Sheet Supplements Safety InstructionsSafety Instructions Certificate of QualityCertificate of Quality EC-Certificate of Con

3、formityEC-Certificate of Conformity Support Center AddressSupport Center Address List of R any deviating instructions in the operating manual are to be ignored. If you have received this document together with a new analyzer, you can skip section 1. If you have received the document together with a

4、firmware update kit or as a download together with a self-extracting archive file, you should read section 1. Initial Steps If you work with a ZVR analyzer for the first time, it is recommended to read the operating manual to familiarize yourself with the unit. If you are already familiar with the i

5、nstrument, this document informs you about new features. Documentation of Firmware Modifications This document covers firmware modifications that are not part of the current operating manual. Firmware Version 3.52ZVx 1112.8050.522E-17 1 Firmware Update System Requirements None Preparations for Updat

6、e No preparations are required. Contents of Firmware Update Kit The update kit comprises the following: Five 3.5/1.44 Mbyte disks labelled as follows: Disk 1 : V3.52 DISK 1“ Disk 2 : V3.52 DISK 2“ Disk 3 : V3.52 DISK 3“ Disk 4 : V3.52 DISK 4“ Disk 5 : V3.52 DISK 5“ This document Update Procedure 1.

7、If you have received a self-extracting archive file per e-mail or as a download a set of disks must first be created from the archive file. Proceed as follows: ? Check if you have received all files. disk1.bin self extracting ZIP file, used to generate update disk 1 data2.cab packed contents of disk

8、 2, automatically unpacked during FW update data3.cab packed contents of disk 3, automatically unpacked during FW update data4.cab packed contents of disk 4, automatically unpacked during FW update data5.cab packed contents of disk 5, automatically unpacked during FW update disk_d.bin this document

9、packed ? Keep five DOS-formatted 3.5 / 1.44 Mbyte disks ready. ? Label disks as follows: V3.52 DISK 1 V3.52 DISK 2 V3.52 DISK 3 V3.52 DISK 4 V3.52 DISK 5 ? Create a temporary directory on your PC (e.g. ZVRTEMP on C:). For this you require about 3 Mbytes of free memory on your hard disk. ? Copy file

10、disk1.bin to this temporary directory. ? Rename file disk1.bin to disk1.exe. ZVxFirmware Version 3.52 1112.8050.523E-17 ? Execute disk1.exe, e.g. by using the following command sequence for Windows95/NT: - RUN C: ZVRTEMP DISK1 - (English version) or - AUSFHREN C: ZVRTEMP DISK1 - (German version). Th

11、e files are extracted. ? Delete file disk1.exe in the temporary directory. The temporary directory should contain the following files: _inst32i.ex_isdel.exe_setup.dll_sys1.cab_user1.cab data.tagdata1.cablang.datlayout.binos.dat readme.txtsetup.exesetup.inisetup.inssetup.lid ? Copy all files to updat

12、e disk 1 (V3.52 DISK 1). Check if all files are on the disk with their correct names. In particular, the underscores (_ as in _inst32iex_) are essential for a successful update. ? The contents of the other 4 disks are already in the format needed for the update. Files data2.cab,., data5.cab must be

13、copied to the corresponding disks DISK2, ., DISK5. The disks are now ready, and you can continue with section 2 If you have received a firmware update kit on a disk . Notes:If any error messages are output during creation of a disk, the installation process for the disk in question must be repeated.

14、 Before re-creating the disk, check if the write protection of the disk has been removed. File disk_d.bin contains this document in pdf format. To unpack the document proceed as follows: ? Copy disk_d.bin to the temporary directory. ? Rename the file to disk_d.exe. ? Execute disk_d.exe, e.g. by usin

15、g the following command sequence for Windows95/NT: - RUN C: ZVRTEMP DISK_D - (English version) or - AUSFHREN C: ZVRTEMP DISK_D - (German version) Firmware Version 3.52ZVx 1112.8050.524E-17 2.If you have received a firmware update kit on a disk . You can load the firmware directly from the disk to yo

16、ur network analyzer. ? Insert the disk DISK 1 into the drive. ? Press the SETUP key and change to the side menu by pressing key. ? Press the FIRMWARE UPDATE softkey. ? Start the update by pressing the UPDATE softkey and follow the instructions on the analyzer display. First, the contents of the upda

17、te disks are copied to the hard disk of the instrument. Then the files are extracted and copied in the directories accordingly. After the extraction, the instrument is rebooted. The firmware update is complete. The previous firmware version may be restored using softkey RESTORE. 3.If problems occur

18、during the firmware update . The new firmware can if necessary also be loaded under NT. This should be done only with an external keyboard and a mouse. Log-in has to be made using the ADMINISTRATOR function, and the device firmware closed. Log in as administrator. ? Press key combination ALT SYSREQ

19、to switch to NT screen if not yet displayed. ? Call up the NT task bar START SHUT DOWN. ? Select Close all programs and logon as different user. ? Hold the SHIFT key down and press the OK key to leave the input window until the login window appears. ? Release the SHIFT key as soon as the login windo

20、w appears. ? Now enter administrator as user name and 894129 as password. Close the device firmware: ? Press the keys CTRL ALT DEL on the external keyboard simultaneously. ? Select the Task Manager. ? Select the Application Rohde the entire data is assigned to the same calibration kit. Afterwards, C

21、REATE INST FILE is used to create the installation file. RESTORE INSTD KITS The RESTORE INSTD KITS softkey resets the parameters of all standards to the values defined in the instrument firmware. Exceptions are calibration kits installed from floppy disk (or from another storage medium). Those are r

22、eset to their original state after the installation. The softkey also activates the same standards which were active in the preset state. Besides that, the default values of the name and reference impedance of the connector families which can be user-defined (SEXLESS USR CONN 1 and USR CONN 2) are r

23、estored. This function is used to cancel all user entries, especially the ones made by mistake. LIST INSTD KITS The LIST INSTD KITS softkey displays the INSTALLED CAL KITS table. This table can not be edited. It shows all calibration kits which were installed from floppy disk (or from another storag

24、e medium) or which were generated by modifying an originally installed calibration kit. Preinstalled kits or kits generated by modification of an originally preinstalled kit are not listed. INSTALLED CAL KITS CONNECTORKITSERIAL # 50 ZV-Z21123456/001 CONNECTOR Connector family The CONNECTOR column sh

25、ows the connector family of the calibration kit. The meaning of the two columns KIT and SERIAL # is as explained under softkey MODIFY STANDARDS. If the standards of a kit have different serial numbers VARIOUS is indicated in the SERIAL # column. ZVxFirmware Version 3.52 1112.8050.5217E-17 INSTALL NE

26、W KIT The INSTALL NEW KIT softkey allows the user to install calibration kits from a floppy disk or another storage medium. If a floppy containing a single calibration kit file (this applies to all floppies provided with the calibration kits from Rohde Gxx is normalized to H21 TOSMSCORR1 to SCORR12

27、TOM-XE11 to E22, G11 to G22, H11 to H22, F11, F21, F12 SENSe1.4:CORRection:POWer:DATA This command is used for reading and writing power correction values for a receiver channel. The data can be transmitted either in ASCII format, or in binary REAL32 format. Transmission in REAL64 format is not poss

28、ible. The parameter may assume the following values: B1Correction data for wave b1 at port 1 INPUTB1Correction data for wave b1 at input b1 B2Correction data for wave b2 at port 2 INPUTB2Correction data for wave b2 at input b2 IFREFCorrection data for reference input a1 on rear panel A1REFCorrection

29、 data for reference input a1 (ZVM and ZVK only) A2REFCorrection data for reference input a2 (ZVM and ZVK only) Syntax:SENSe1.4:CORRection:POWer:DATA, | . Example: CORR:POW:DATA B1, Features:*RST value: SCPI: - device-specific Firmware Version 3.52ZVx 1112.8050.5226E-17 SOURce Subsystem (Re section 3

30、.6.15) COMMANDPARAMETERUNITCOMMENT SOURce :POWer :LEVel :IMMediate :AMPLitude :CAMPlitude :A :ESRC :SLOPe :EXTernal :AMPLitude :SLOPe :ALC :STATe :NLINear :COMP :RANGe :UPPer :LOWer :SOI :RANGe :UPPer :LOWer :TOI :RANGe :UPPer :LOWer :CENTer :SPAN :STARt :STOP :CORRection :DATA :EXT :SWEep :NREading

31、s :ACQuire :LLISt :STATE , | . , , , LIN | LOG A1 | A2 | ESRC1 | ESRC2 , , . DBM DBM DBM DB/GHZ DBM DB/GHZ dBm dBm dBm dBm dBm dBm dBm dB dBm dBm HZ, HZ, , , HZ, dB no query ZVxFirmware Version 3.52 1112.8050.5227E-17 COMMANDPARAMETERUNITCOMMENT :FREQuency :CW :FIXED :CONVersion :ARBitrary :IFRequen

33、n values for a generator channel. The data can be transmitted either in ASCII format, or in binary REAL32 format. Transmission in REAL64 format is not possible. The parameter is used for selecting the correction data set as follows: A1Generator output a1 A2Generator output a2 ESRC1External generator

34、 1 ESRC2External generator 2 Syntax:SOURce1.4:POWer:CORRection:DATA, | . Example: SOUR:POW:CORR:DATA A1, Features:*RST value: SCPI: - device-specific Firmware Version 3.52ZVx 1112.8050.5228E-17 6 Special Features The format of the system error calibration (SFK) files and the calibration kit (CalKit)

35、 files was changed for version 3.50. The files from older firmware versions are therefore converted to the new data format. The change concerns files with the extension CAC, CA1 to CA4, CK, CKD and DAT. The old files are not deleted but renamed, i.e. an additional extension .BC350 is appended. For e

36、xample, FACTORY.CAC is renamed to FACTORY.CAC.BC350. Note: There is no conversion if version 3.50 is updated to version 3.52. The new data format cannot be processed by older firmware versions. The following procedure should be adopted, therefore, when restoring a previous firmware version (e.g. V 3

37、.40): ? Restore the old firmware version as usual by means of SETUP FIRMWARE UPDATE RESTORE. ? Terminate the firmware. ? In the Explorer, change to the C:R_SINSTRCAL directory. ? Each file for which a file of identical name but with the additional extension .BC350 exists, must be renamed, for exampl

38、e by appending the additional extension .V350. For example, N50.CKD must be renamed to N50.CKD.V350. Note: If a file with the name CK_INST.DAT exists, it must in any case be renamed to CK_INST.DAT.V350“, no matter whether or not a file CK_INST.DAT.BC350 exists. ? All files with the additional extens

39、ion .BC350 must be renamed, i.e. the extension has to be removed. For example, N50.CKD.BC350 has to be renamed to N50.CKD. ? Start the firmware by means of START START INSTRUMENT. The SFK and CalKit files that were available prior to the update to version 3.50 or 3.52 are now fully available again.

40、New files added through the version 3.50 or 3.52 update cannot be used however. As an alternative to the above procedure, the complete C:R_SINSTRCAL directory can be saved, for example under C:R_SINSTRCAL.BC350, before the update to version 3.50 or 3.52 is made. After restoring the old firmware vers

41、ion, this directory must be renamed to C:R_SINSTRCAL. ZVxContents 1127.8700.12 3 E-3 Contents 1 Preparation for Use.1.1 1.1Introduction.1.1 1.2Legend for Front and Rear View.1.1 1.2.1 Front View ZVR, ZVK and ZVM.1.1 1.2.1.1 Front View ZVR .1.1 1.2.1.2 Front View ZVK, ZVM.1.13 1.2.2 Rear View ZVR, ZV

42、K and ZVM.1.15 1.3Start-Up.1.20 1.3.1 Unpacking the Instrument .1.20 1.3.2 Instrument Setup.1.20 1.3.2.1 Stand-alone Operation .1.20 1.3.2.2 19 Rack Installation.1.21 1.3.3 EMI Protection Measures.1.21 1.3.4 Connecting to AC Power.1.21 1.3.5 AC Power Line Fuses.1.21 1.3.6 Battery-Powered Memory.1.22 1.4Controller Function.1.23 1.5Connecting a Mouse .1.25 1.6Connecting an External Keyboard.1.25 1.7Connecting an External Monitor.1.26 1.8Connecting an Output Device.1.28 1.9Connecting a CD-ROM Drive.1.35 1.10Firmware

展开阅读全文