《Innovason the-fm8vb-and-sensoft-12-0-11-quick-guide-472108电路图.pdf》由会员分享，可在线阅读，更多相关《Innovason the-fm8vb-and-sensoft-12-0-11-quick-guide-472108电路图.pdf（41页珍藏版）》请在收音机爱好者资料库上搜索。
1、 Version : 1.0 DP0041 The FM-8VB effect module and Sensoft 12.0 Quick guide INNOVASON February 2008 Page 1 of 41 Installing and using of the FM-8VB Installing and operating of SENSOFT 12.0.11 RadioFans.CN 收音机爱 好者资料库 Content The FM-8VB effect module and Sensoft 12.0 Quick guide INNOVASON February 200
2、8 Page 2 of 41 I. The FM-8VB at a glance . 3 II. Installing of the FM-8VB card. 3 III. Installing of Sensoft 12. 5 III.1 Minimum required configuration. 5 III.2 Installation. 6 III.3 Updating, new “release” 7 III.4 Configuration. 9 IV. Update the DSP module to version 4.0.3411 V. Update the FM-8VB c
3、ard to version 1.1.38. 14 VI. Upgrade your MC and SCoptical 18 VII. Update your ARC card and DioES modules. 19 VIII. Configure the Stereo/Mono status of the FM-8VB. 20 IX. Using an FX Bay fed by an Aux. 22 IX. 1 A stereo Bay fed by a Mono Auxiliary 22 IX. 2 A stereo Bay fed by a Stereo Auxiliary. 27
4、 X. Using an FX bay as an inserted processing. 28 X. 1 Using a MONO inserted bay. 28 X. 2 Using a Stereo inserted Bay. 30 XI. Locking a Rack. 33 XII. Editing the Effects .34 XII. 1 View of the plugins editors. 34 XIII. Some little words about the 16 floating processing39 Content RadioFans.CN 收音机爱 好者
5、资料库 The FM-8VB at a glance The FM-8VB effect module and Sensoft 12.0 Quick guide INNOVASON February 2008 Page 3 of 41 I. The FM-8VB at a glance The FM-8VB card is a 32 engines FX card. This card is seen by the system as an 8 INPUTS and 8 OUTPUTS card. 4 FX engines are available between each input an
6、d output of the card. Depending of your needs the I/O, by pair, can be declared as a Stereo FX bay or 2 mono FX bays. Although 32 engines are available, the global resources of these engines can be strongly reduced if you use a lot of “greedy” effects, ie: 4 JustVerb (VB Audio Reverb) uses between 8
7、0 and 90 % of the complete resources of one card. In opposite, up to 32 Limitor or De-esser treatments can be assigned without using the complete resources of the DSP. In order to maximum simplify its use, we have imagined the utilization of the FX like you would do with your external bay. The FM-8V
8、B provides you 8 Mono or 4 Stereo bays that you can use as standard FX (fed by an Aux and returning to some inputs channels of the desk) and/or inserted treatments. All the I/O configuration is managed thru the standard patch grids provided by Sensoft 12. A TAP-TEMPO jack input is available front of
9、 the FM-8V card. This future option will allow to determine a global tempo thru a standard Tap Pedal. This global Tempo can be selected to automatically determine the Reverbs Pre-delay, the MultiTap Delay intervals, the Modulator frequency, etc II. Installing of the FM-8VB card The FM-8VB effect car
10、d can be installed in the Mix-Box of your system (Local rack of the Sy80, Back of the Sy48). It is planned that this module, in a close future, will work in a DioCore. As the module is detected by the system as an INPUT and an OUTPUT card you have to take care, when used with a Muxipaire Stage-Box,
11、that no card is installed on the same slot (identified by its geographic letter) of the Stage-Box, ie: if a FM-8VB card is installed on the G slot of the Local Rack, no card can be installed on the slot G of the Stage- Box. Obviously, this restriction does not concern the DioCore where, in this exam
12、ple, any I/O module could be installed on the slot G. RadioFans.CN 收音机爱 好者资料库 Installing of the FM-8VB card The FM-8VB effect module and Sensoft 12.0 Quick guide INNOVASON February 2008 Page 4 of 41 Please to install your FM-8VB card, just follow the following steps : 1 Remove the blank panel on the
13、 slot where you want to install your FM-8VB. Just make a quarter tour on the 4 screws. 2 Slowly pull the panel and keep it fore an eventual future use. 3 Insert the FM-8 card. The PCB must be carefully inserter in the 2 plastic guides. 4 Strongly push the card to ensure a good and secured connection
14、. 5 Switch on the rack, the 4 Blue LEDs indicate that the card is correctly installed and powered. Do the same operations to install a FM-8VB card in a Sy48 local rack. Installing of Sensoft 12 The FM-8VB effect module and Sensoft 12.0 Quick guide INNOVASON February 2008 Page 5 of 41 III. Installing
15、 of Sensoft 12 III.1 Minimum required configuration Before installing Sensoft 12 be sure that your system is configured like following: A Information available from the main mixing screen of Sensoft : The current installed Sensoft version is 11.0 or 11.1 B Information available in the Patch IN or OU
16、T grid of Sensoft, left selected TAB is “MUXI” and top selected TAB is “CONFIG” : Your DSP version is 4.0.28 or 4.0.34 The DioES module installed on the DSP card (Ethersound option) is in version 1.6 Your MCoptical version is 7.0 C - Information available on the Big Eprom of the SCoptical module : Y
17、our SCoptical version (if you use a Stage-Box) is in version 4.0 D Information available in the Patch IN or OUT grid, left selected TAB is “DIO1” and top selected TAB is “CONFIG” : Your Arc version (if you use a DioCore) is 1.28 The DioES module of the ARC card is in version 1.6 Sensoft 12 is delive
18、red with an installation USB key containing all the necessary files to install the System (Win XPE) and Sensoft 12. If you want to install Sensoft 12 by using a previous version USB Key (Sensoft 11, Sensoft 10) please follow the following steps : 1 Insert the USB key in your Lap Top or Desk Top comp
19、uter 2 Copy on this Key the 3 files named install.bat, update.bat and Sensoft.zip. These 3 files are available from our Web Site (in SENSOFT12.0.ZIP downloaded file) or from the CD delivered with the Sensoft 12 upgrade kit. Say “Yes” when your system informs you that these 3 files will erase and rep
20、lace the 3 existing files on your key. Installing of Sensoft 12 The FM-8VB effect module and Sensoft 12.0 Quick guide INNOVASON February 2008 Page 6 of 41 Your Key is now ready to install Sensoft 12.0 on your console. III.2 Installation A fresh installation is necessary when the Sensoft versions fir
21、st digit changes, for example, when changing from version 11 to version 12. It is also necessary if you reinstall your Windows XPE operating system. The previous version will be permanently replaced and the files/pages created with that version will be erased. Generally, a new version can re-interpr
22、et the pages of the previous version (wholly or partially: new functions = new parameters). For example Sensoft 12 re- interprets the pages created with Sensoft 11. First, using the “Export” function in the FILE menu, save all you previously created files on a USB mass storage device. Switch your co
23、nsole off and follow the step by step procedure below to install Sensoft: 1- Insert your USB key in one of the consoles available ports. Launch the console and immediately press F8 or F11 to access the startup menu The 3 files to copy on the installing key Installing of Sensoft 12 The FM-8VB effect
24、module and Sensoft 12.0 Quick guide INNOVASON February 2008 Page 7 of 41 2- As shown above, select the USB port. Validate with ENTER. 3- At the root of the temporary Win98 boot, type “install c:” and validate with ENTER This command installs the Sensoft version currently on the USB key. Once the ins
25、tallation is finished and “a:” is displayed on screen, you can reboot your console to immediately start using your new version of Sensoft 12. When you first launch Sensoft, you are automatically invited to configure the software in order to adapt it to the platform on which it has been installed. Se
26、ction III.4 explains this configuration window thoroughly. III.3 Updating, new “release” When updating a new release of Sensoft 12 you may retain your shows files on disc. Going back to an earlier version of Sensoft (i.e. Sensoft 11.x), a complete reinstallation will be necessary (see section III.2)
27、. Shows are not backwards compatible. Switch your console off and follow the step by step procedure below to install Sensoft: 1- Insert your USB key in one of the consoles available ports. Launch the console and immediately press F8 or F11 to access the startup menu. Installing of Sensoft 12 The FM-
28、8VB effect module and Sensoft 12.0 Quick guide INNOVASON February 2008 Page 8 of 41 2- As shown below, select the USB port. Validate with ENTER. 3- At the root of the temporary Win98 boot, type “update c:” and validate with ENTER This command replaces the prior Sensoft release installed on your cons
29、ole with the one on the USB key. Once the installation is finished and “a:” is displayed on screen, you can reboot your console to immediately start using your new version of Sensoft 12. An update retains parameters and all files residing on the console. Reconfiguring is unnecessary and, when launch
30、ed, Sensoft will return to the last page used and all its parameters. Installing of Sensoft 12 The FM-8VB effect module and Sensoft 12.0 Quick guide INNOVASON February 2008 Page 9 of 41 III.4 Configuration After a new installation, Sensoft displays the screen below so you can chose the platform and
31、configure the system. To access this screen at anytime, go to UTIL menus ABOUT and type the invisible password “innova” . This screens purpose is to configure the consoles elements for data exchange between PC, Mix Box rack and control surface. The parameters on this screen are important for your co
32、nsole and Sensoft software to function properly. Therefore, you must respect the indications that are outlined below. The consoles are delivered from the factory with optimized settings, and it is wise to keep them as they are. Our customer service department might ask you to change these during tec
33、hnical support. Use the up and down arrow keys to select the parameters (highlighted in yellow), and the left and right keys to change the selected parameters value. Console : Sy80, management of the Sy80 control surface, remote audio controller compatible with DSP Sy80 cards. GRAND LIVE, management
34、 of the GL control surface, remote audio controller compatible with DSP Sy80 cards. Sy48, management of the Sy48 control surface, remote audio controller compatible with DSP Sy48 cards. Serial Port Number : Disable for use on an Off-line PC, or without the console. 2 for a Sy80, Sy48 and GL equipped
35、 with an 800MHz or 1GHz PC ISA800. 3 and 4 reserved for specific usage Installing of Sensoft 12 The FM-8VB effect module and Sensoft 12.0 Quick guide INNOVASON February 2008 Page 10 of 41 When the chosen serial port detects the control surface, a yellow RESET DESK window is displayed and its channel
36、 control panel buttons blink twice. On the system status line, on top of the screen, the red background NO DESK message, turns to a green background DESK message. If the serial port is not valid, the red background NO DESK status will remain. When controlling the console with an external PC, try all
37、 the port numbers until the console is detected. Parallel port Number: 1 (default) for normal use of the console DISABLE for use on an Off-line PC, or without the audio rack. New Design : NO (default), normal use YES reserved application MIDI CABLE TEST : NO inactive, normal status OK or BAD CONNECT
38、ION when testing a MIDI cable connected between the IN and OUT port of the console. MIDI SETUP : NO inactive, normal status WAIT. Loading the SENSOFTFILES80XMIDI.CFG text file. Transfer of a MIDI SYSEX file to initialize a Midi-Solutions R8 rack, giving you access to 8 fader-start relays compatible
39、with the data sent by Sensoft. The characteristics of this equipment is available on the web site. Also see section 6.0 of Sensoft 8s user guide for information on fader-starts Faders Calibration : Press the right arrow key to launch a fader calibration process. Just follow the indications given by
40、Sensoft. Firmware Update : Press the right arrow key to launch the firmware updater. This software allows to update the firware of the DSP card, the UM-8PO card and the FM-8VB card. The procedure is explained on the following sections of this quick guide. Update the DSP module to version 4.0.33 The
41、FM-8VB effect module and Sensoft 12.0 Quick guide INNOVASON February 2008 Page 11 of 41 IV. Update the DSP module to version 4.0.34 The firmware 4.0.34 has the big advantage to correct some recently discovered bugs on the DSP board. One of this concerns the Line I/O available on the SubD connectors
42、of the DSP card. In some rare case, the device in charge of these I/O was not correctly initialised, the result is no sound on these I/O. 1- From the configuration screen (see section III.4), select the “Firmware Update” line and press the right arrows () to launch the firmware updater. 2 A warning
43、message explains to disconnect the outputs of the console to any powered audio system. During the programming process some hazardous noises could be generated by the DSP board, this could be dangerous for your ears and the speakers 3 If the communication between the PC and the audio racks module is
44、impossible, the following message will appear. Please check the Audio rack powering, the Jeager cable connection etc 4- If everything is fine regarding the system and communication you should see the following screen. Update the DSP module to version 4.0.33 The FM-8VB effect module and Sensoft 12.0
45、Quick guide INNOVASON February 2008 Page 12 of 41 5 Select the DSP board slot and double click on it to launch the programming process. 6 A window invites you to select the firmware available in the “Firmware” directory of the Hard disk of the PC. This firmware is coming from the last time that you
46、installed Sensoft (Sensoft 12.0 in this case). If you want to use a firmware downloaded form our Web Site, fell free to select a USB device containing this firmware. Select the DSP_4034.LD3 file corresponding to the 4.0.34 firmware version. Update the DSP module to version 4.0.33 The FM-8VB effect m
47、odule and Sensoft 12.0 Quick guide INNOVASON February 2008 Page 13 of 41 7 Confirm that you will replace the actual firmware by the new one by pressing DOWNLOAD on the following message. 8 Flash memory of the DSP is erased Update the FM-8VB card to version 1.1.36 The FM-8VB effect module and Sensoft 12.0 Quick guide INNOVASON February 2008 Page 14 of 41 9 The 4.0.34 firmware is loaded in the DSP flash memory 10 After the “SUCCESSFUL” message, your DSP is now programmed and updated. Exit from the updater software by closing the main window. This will re-launch Sensoft 12 V.
免费区 
