《General_Music_LEM_Procon_Plus_Series_Service_Manual电路图.pdf》由会员分享，可在线阅读，更多相关《General_Music_LEM_Procon_Plus_Series_Service_Manual电路图.pdf（13页珍藏版）》请在收音机爱好者资料库上搜索。
1、1 Index Soldering point. Male connector. Female connector. M/F faston connector. Test point. Supply voltage.Logic supply ground. Analog supply ground. Chassis ground. Earth ground. Flag joined with one or more flags GENERALMUSIC S.p.A. Sales Division: 47842 S.Giovanni in Marignano (RN) ITALY - Via d
2、elle Rose, 12 Phone +39(0)541/959511 - Fax +39(0)541/957404 - Internet: Technical specifications, transistor packages, Procon 400p test procedures.2 Procon 750p, Procon 1000p test procedures.3 Procon 1250p, Procon 1500p test procedures. 6 7Procon 750p schematic. 8 Procon 400p schematic. 9Procon 1250
3、p schematic. 10 Procon 1000p schematic. Procon 1500p schematic. 11Procon 1800p schematic. 12Procon 2200p schematic. 13Spare part list. 4 Procon 1800p, Procon 2200p test procedures. 5 with the same signal name inscribed. ATTENTIONObserve precautions when handling electrostatic sensitive devices. Noti
4、ce Service must be carried out by qualified personnel only. Any tampering carried out by unqualified personnel during the guarantee period will forfeit the right to guarantee. For a correct operation of the instrument, after having switched off, be careful to wait at least 3 seconds before switching
5、 on again. To improve the devices specifications, the schematic diagrams may be subject to change without prior notice. All components marked by this symbol have special safety characteristics, when replacing any of these components use only manufacturers specified parts. The () micro symbol of capa
6、citance value is substituted by U. The () omega symbol of resistance value is substituted by E. The electrolytic capacitors are 25Vdc rated voltage unless otherwise specified. All resistors are 1/8W unless otherwise specified. All switches shown in the OFF position. All DC voltages measured to groun
7、d with a voltmeter 20KOhm/V. service manual schematic diagrams CODE: 270312 Power Amplifiers procon plus RadioFans.CN 收音机爱 好者资料库 2 PROCON400p - Test procedures PRECAUTION To prevent short circuit during any test, the oscilloscope must be EARTH INSULATED, this occurs because some test require to conn
8、ect its probe to the amplifi er output, non-compliance may cause damages to oscilloscope inputs circuitry. Before removing or installing any modules and connectors, disconnect the amplifi er from AC MAINS and measure the DC supply voltages across each of the power supply capacitors. If your measurem
9、ent on any of the caps is greater than 10Vdc, connect a 100E 60W resistor across the applicable caps to discharge them for your safety. Remember to remove the discharge resistor immediately after discharging caps. Do not power up the amplifi er with the discharge resistor connected. Do not check the
10、 amplifi er with the speakers connected use the appropriate load resistors only. BE CAREFUL increasing the Variac you must not exceed the nominal mains voltage plus its tolerance (see specifi cations) any upper volt- age can be cause of damage. VISUAL CHECK Use compressed air to clear dust in the am
11、plifi er chassis. Before proceed to supply the amplifi er check visually the internal assembly, if appears an evident damage fi nd the most possible rea- sons that cause it. Check the wiring cables for possible interruptions or shorts. If the damage has burnt a printed circuit board dont try to repa
12、ir it, replace with a new one. TESTING GEAR Audio Generator Dual Trace Oscilloscope Digital Multimeter 4E 300W, 8E 450W, 100E 60W resistors Variac Digital Thermometer (not indispensable) SETUP Connect the Variac between the Mains and the amplifi er and set it at zero voltage. Turn full counter-clock
13、wise the LEVEL potentiometers. Connect the audio generator to the channel inputs and set it to 1KHz 775mVrms (0dBu) sinusoidal signal. Connect the two scope traces to the amplifi er outputs, before the relay, and set them in DC at 20V/div. 2mS/div. SUPPLY CHECK Verify with the Multimeter the insulat
14、ion between the heatsinks and all transistor collectors mounted on them; placing the multimeter tips between the screw heads and the collector pins you can exclude an erroneus reading due to the insulation of the heatsink anodization. Verify with the Multimeter the NTC (RT1) and R1 paralleled resist
15、or value, it must be about 1080ohm (at 25c). Disconnect the amplifi er module supplies of each channel (red and yellow wires). Set the Variac to the nominal mains voltage, turn on the Amplifi er, then check with the Multimeter the AC supply voltages: F1-F2 = 292Vac. RED secondary wires = 879Vac. Re-
16、set the Variac at zero voltage, turn off the amplifi er and recon- nect the supplies at each amplifi er module. Set up the Variac slowly monitoring the oscilloscope screen, it should display no signal; if you notice a DC voltage or a protection trips check the amplifi er as suggested in the ADVICES.
17、 As soon as the +12VF supply circuit reaches its nominal value, all cooling fans run at their minimum and the speaker output relais (J201-202) switch. When the Variac ac voltage reaches the nominal voltage verify the DC supplies as follow: +VCC = +596Vdc -VCC = -596Vdc U101 pin 8 = +120.5Vdc U101 pi
18、n 4 = -120.5Vdc U403 pin 3 = +120.5Vdc If one or more voltages dont correspond, check the rectifi ers, ca- pacitors and transformers disconnecting them from cir cuit ry. CHANNEL CHECK Be sure you have dis con nect ed the load re sis tor. Increasing the input sig nal also the output signal raise ac c
19、ord ing ly, it must be sym met - ri cal without vis i ble dis tor tion or os cil la tion as shown in figure (note: the fi g ure is rep re sent a tive dont re fer to the levels dis played). If there is a dis tor tion read the sec tion ADVICES. When the input sig- nal exceeds -20dBu (20Vpp on output)
20、the fans turn at their max i mum speed. Firstly you must check the channel without load, after- wards you must repeat the check with the loads attached, the following table reports the approx. maximum level obtainable with this amp: out level in level no load 113Vpp +1.5dBu 1CH 4E 91Vpp -0.2dBu 2CH
21、4E 82Vpp -2.0dBu Bridge 8E 161Vpp -2.3dBu LEVEL METER ADJUSTMENT Check if the clip led lights at -2dBu on input (80Vpp on output), if necessary adjust the trimmers W301/2 on dis play board. OFFSET ADJUSTMENT Set the input level at minimum (no signal), the output dc offset voltage must be within rang
22、e 20mV, if necessary adjust the VR201 trimmer (for each channel) to be within this range. BIAS ADJUSTMENT No bias adjustment is necessary for this amplifi er circuitry. ADVICES If you have determinate that the problem is a short on a rail, you must check the output transistors. To determine which tr
23、ansistor devices are bad, use a soldering iron to lift one leg of each emitter pin and measure the resistance across emitter and collector of each device. Unsolder and lift one leg of each base pin and check the base-collector resistance. Replace any device that measure as a short. If all the transi
24、stors are OK, unsolder and lift one leg of each diode and check them. Check the circuit board for open foil traces. Use the Multimeter to check the resistors, particularly the base and emitter resistors of damaged transistor. If the input sinewave appears to be distorted during the negative cycle, y
25、ou can assume that the problem is located somewhere in the circuitry of the positive rail. If the positive cycle appears distorted, you can assume that the problem is in the circuitry of the negative rail. The dc voltages printed on the schematics are measured with the amplifi er in steady state wit
26、hout input signal and nominal mains volt- age supply, it can be useful to localize a damage. POWER SPECIFICATIONS400P750P1000P1250P1500P1800P2200P EIA output power 1kHz, THD maximum 1% Both channels 8 ohm 4 ohm 8 ohm BRIDGED 125+125 200+200 400 215+215 375+375 750 300+300 550+550 1100 375+375 625+62
27、5 1250 450+450 750+750 1500 550+550 900+900 1800 650+650 1100+1100 2200 ELECTRICAL SPECIFICATIONS400P750P1000P1250P1500P1800P2200P INPUT SENSITIVITY INPUT IMPEDANCE FREQUENCY RESPONSE VOLTAGE GAIN32dB33dB35dB36dB37dB37dB39dB SLEW RATE DAMPING FACTOR CROSSTALK S/N ratio Harmonic distortion THD Interm
28、odulation distortion SMPTE GENERAL SPECIFICATIONS400P750P1000P1250P1500P1800P2200P PROTECTIONS CONTROLS INDICATORS CONNECTORS IN OUT POWER SUPPLY DIMENSIONSmm (WxHxD) WEIGHTkg13151819.52123.525 PROCON PLUS SERIES TECHNICAL SPECIFICATIONS 0dB (0.775V) 10 kOhms (balanced) 1050000 Hz (-0.5dB) 22 V/ms 4
29、00:1 1kHz, 8Ohms -82 dB (1KHz) Power transformer thermal protection Short circuit protection Sensor for current on outputs CLIP Limiter on each channel Soft-start circuit (1000P to 2200P) -100 dB 483x88x456 0.1% (ref 20Hz -20KHz) 0.1% (SMPTE method, 60Hz placing the multimeter tips between the screw
30、 heads and the collector pins you can exclude an erroneus reading due to the insulation of the heatsink anodization. Verify with the Multimeter the NTC (RT1) and R1 paralleled resistor value, it must be about 1080ohm (at 25c). Disconnect the amplifi er module supplies of each channel (red and yellow
31、 wires). Set the Variac to the nominal mains voltage, turn on the Amplifi er, then check with the Multimeter the AC supply voltages: F1-F2 = 292Vac. RED secondary wires = 10610Vac. Re-set the Variac at zero voltage, turn off the amplifi er and recon- nect the supplies at each amplifi er module. Set
32、up the Variac slowly monitoring the oscilloscope screen, it should display no signal; if you notice a DC voltage or a protection trips check the amplifi er as suggested in the ADVICES. As soon as the +12VF supply circuit reaches its nominal value, all cooling fans run at their minimum and the speake
33、r output relais (J201-202) switch. When the Variac ac voltage reaches the nominal voltage verify the DC supplies as follow: +VCC = +727Vdc -VCC = -727Vdc U101 pin 8 = +120.5Vdc U101 pin 4 = -120.5Vdc U403 pin 3 = +120.5Vdc If one or more voltages dont correspond, check the rectifi ers, ca- pacitors
34、and transformers disconnecting them from cir cuit ry. CHANNEL CHECK Be sure you have dis con nect ed the load re sis tor. Increasing the input sig nal also the output signal raise ac cord ing ly, it must be sym met - ri cal without vis i ble dis tor tion or os cil la tion as shown in figure (note: t
35、he fi g ure is rep re sent a tive dont re fer to the levels dis played). If there is a dis tor tion read the sec tion ADVICES. When the input sig- nal exceeds -20dBu (20Vpp on output) the fans turn at their max i mum speed. Firstly you must check the channel without load, after- wards you must repea
36、t the check with the loads attached, the following table reports the approx. maximum level obtainable with this amp: out level in level no load 139Vpp +3.0dBu 1CH 4E 117Vpp +1.5dBu 2CH 4E 109Vpp +0.9dBu Bridge 8E 214Vpp +0.7dBu LEVEL METER ADJUSTMENT Check if the clip led lights at -1dBu on input (9
37、0Vpp on output), if necessary adjust the trimmers W301/2 on dis play board. OFFSET ADJUSTMENT Set the input level at minimum (no signal), the output dc offset voltage must be within range 20mV, if necessary adjust the VR201 trimmer (for each channel) to be within this range. BIAS ADJUSTMENT No bias
38、adjustment is necessary for this amplifi er circuitry. ADVICES If you have determinate that the problem is a short on a rail, you must check the output transistors. To determine which transistor devices are bad, use a soldering iron to lift one leg of each emitter pin and measure the resistance acro
39、ss emitter and collector of each device. Unsolder and lift one leg of each base pin and check the base-collector resistance. Replace any device that measure as a short. If all the transistors are OK, unsolder and lift one leg of each diode and check them. Check the circuit board for open foil traces
40、. Use the Multimeter to check the resistors, particularly the base and emitter resistors of damaged transistor. If the input sinewave appears to be distorted during the negative cycle, you can assume that the problem is located somewhere in the circuitry of the positive rail. If the positive cycle a
41、ppears distorted, you can assume that the problem is in the circuitry of the negative rail. The dc voltages printed on the schematics are measured with the amplifi er in steady state without input signal and nominal mains volt- age supply, it can be useful to localize a damage. PROCON1000p - Test pr
42、ocedures PRECAUTION To prevent short circuit during any test, the oscilloscope must be EARTH INSULATED, this occurs because some test require to connect its probe to the amplifi er output, non-compliance may cause damages to oscilloscope inputs circuitry. Before removing or installing any modules an
43、d connectors, disconnect the amplifi er from AC MAINS and measure the DC supply voltages across each of the power supply capacitors. If your measurement on any of the caps is greater than 10Vdc, connect a 100E 80W resistor across the applicable caps to discharge them for your safety. Remember to rem
44、ove the discharge resistor immediately after discharging caps. Do not power up the amplifi er with the discharge resistor connected. Do not check the amplifi er with the speakers connected use the appropriate load resistors only. BE CAREFUL increasing the Variac you must not exceed the nominal mains
45、 voltage plus its tolerance (see specifi cations) any upper volt- age can be cause of damage. VISUAL CHECK Use compressed air to clear dust in the amplifi er chassis. Before proceed to supply the amplifi er check visually the internal assembly, if appears an evident damage fi nd the most possible re
46、a- sons that cause it. Check the wiring cables for possible interruptions or shorts. If the damage has burnt a printed circuit board dont try to repair it, replace with a new one. TESTING GEAR Audio Generator Dual Trace Oscilloscope Digital Multimeter 4E 700W, 8E 1100W, 100E 80W resistors Variac Dig
47、ital Thermometer (not indispensable) SETUP Connect the Variac between the Mains and the amplifi er and set it at zero voltage. Turn full counter-clockwise the LEVEL potentiometers. Connect the audio generator to the channel inputs and set it to 1KHz 775mVrms (0dBu) sinusoidal signal. Connect the two
48、 scope traces to the amplifi er outputs, before the relay, and set them in DC at 50V/div. 2mS/div. SUPPLY CHECK Verify with the Multimeter the insulation between the heatsinks and all transistor collectors mounted on them; placing the multimeter tips between the screw heads and the collector pins yo
49、u can exclude an erroneus reading due to the insulation of the heatsink anodization. Verify with the Multimeter the NTC (RT1) and R1 paralleled resistor value, it must be about 7Kohm (at 25c). Disconnect the amplifi er module supplies of each channel (red and yellow wires). Set the Variac to the nominal mains v
免费区 
