《Rauland Telecenter Iv - Ki-1629-2524 Master Clock And Intercom Programming 电路图.pdf》由会员分享，可在线阅读，更多相关《Rauland Telecenter Iv - Ki-1629-2524 Master Clock And Intercom Programming 电路图.pdf（17页珍藏版）》请在收音机爱好者资料库上搜索。
1、KI-1 629 ChronoCom TM Master Clock and Intercom Controller Programming RAULAND-BORG CORPORATION ? 3450 West Oakton Street, Skokie, Illinois 60076-2951 ? (708) 679-0900 General Information Table of Contents 2 Description n. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Power-up . . . . . . . . . . . . .
3、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Programming Summary 2 Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4、 . . . . . . . . . . . . . . . . . . . .2 Access to Programmingg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 General Methods. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Exiting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Planning 3 Information Needed d. . . .
6、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Planning Chart s. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7、. . . . . . . . Zones Chart.: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Stations Chart t. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8、 . . . . . . . . . . . . . . . . . . . . . . The Events Chart n. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Clock Modes A-F 5 Mode A (Preprogrammed Clock Codes. . . . . . . . . . . . . . . . . .
9、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mode B (Custom Clock Code) ). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Creating a Custom Code e. . . . . . . . . . . . . .
10、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Entering the Custom Codee. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Mode C (Holidays and Time Cha
11、nges) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mode D (Edit Holiday events). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Mode E (Relay
12、 Panels,Comm Activation).7 Mode F (Events: Totals and Erase All).7 Clock Modes l-6 7 Mode1(Room Numbers) ). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 Mode 2 (Zones and Scanning).l 0 Mode l (Date ). . . .
13、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Mode 2 (Time) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14、 . . . . . . . . . . . . 8 Mode 3 (Enter Regular Events) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mode 4 (Edit Regular Events). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15、 . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 Mode 5 (Zone Duration) ). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 Mode 6 (Activate Zones and Schedules) . . . . . . . . . . . . . . . . . . .
16、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 Mode 0 (Run) ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 0 Communication Modes 10 1989 RAULAND-BORG
17、CORPORATION ? Printed in U.S.A. Ruig. 4/90 Page 1 of 17 RadioFans.CN 收音机爱 好者资料库 2524 ChronoCom Programming Mode 3 (System Options). . . . . . . . . . . . . . . . . . . TC4200 Display. Automatically Connect Priority Call-ins. Remote Phone. Mode 4 (Monitoring Duration). . . . . . . . . . . . . . . Mod
18、e 5 (Call-in Sensitivity). ModeO(Run). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 .11 . . . ii .12 .12 Work Sheet for Custom Se
19、condary-Clock Code 13 Example. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Commentary: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 13 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20、 . . . . . . . Programming Charts 14 General Information Description The Rauland 2524 is a multi-function Master Clock and Communications Control Center. As a master clock, it will synchronize virtually any kind of secondary clock and control up to 350 “events” (such as sending tone signals or turni
21、ng lights and equipment on and off). As an intercom controller, it adds control of room-switching functions and display functions to Director III intercom-control els. a4anuals This manual tells how to program the 2524 for both clock and intercom functions. The first section gives the basic programm
22、ing procedures. The “Clock Modes A-F” section explains the programming for the general settings needed by the unit, whether it is used only as a master clock or also as a control unit for communications. The last two sections deal with the clock and intercom func- tions, respectively. Generally, the
23、 Clock Modes A-E, especially Clock Mode A, should be done before the numerical modes. Refer also to KI-1628, 2524 Installation, and KI-1630, 2524 Opera- tfon. Following the text are four tables that list all of the programming functions. Also attached are a work sheet for devising a special clock-co
24、rrection code and charts for planning the system programming. Power-up When the 2524 is turned on, its displays normally appear as follows: the “Mode” window reads “0” (Run Mode), the “Time” window shows the current time, the “Sched” (“Schedule”) window shows a flashing “P” (to indicate that the pow
25、er was off), and the “Clock” LED lights (to show the unit is set for clock operation). Push any key to stop the flashing “P.” * The “Sched” window will show the number of the schedule currently in use. Note: If the battery was “disabled,” the “Time” display may be random. In this case, set the date
26、and time (Clock Modes 1 and 2). Programming Summary This section gives the procedures for accessing, chang- ing, and entering programming information. After this summary, there is a section on planning. Then the three groups of programming modes are explained. The alphabetical modes (A-F) are explai
27、ned first, because this group affects both clock and intercom operation; moreover, these settings arc usually entered during setup and left that way, except for the annual holiday and Daylight Savings Time changes. The other clock and the intercom modes follow in that order. Sequence Important: P Be
28、fore entering clock events (Clock Mode editing them (Clock Mode 4), you should enter any c ock-correction codes (Mode A), because each code takes up two outputs that arc not, consequently, available for events. The 2524 will not allow you to enter an event for a zone that is taken up by a clock code
29、. Should you enter events for zones that you subsequently take up with a clock code, the 2524 will not erase them. However, it will not activate events in clock-code tones, and these zones LEDs will not light when you review the events in Clock Mode 4. The remaining modes may be programmed in any or
30、der. Access to Programming To begin programming, the clock must be in the Clock Run Mode (“0”). Step 1. Enter the Security Code (Funct 2524-that is, press in succession the Funct, 2, 5 , 2, and 4 keys): Page 2 4/90 RadioFans.CN 收音机爱 好者资料库 2524 ChronoCom Programming * The “0” in the “Mode” window wil
31、l flash, meaning that you can select a programming mode. If you pause more than five seconds between keystrokes or enter invalid keystrokes, the clock will display “ErrO,” “beep,” and, after a moment, revert to the Clock Run Mode. Step 2. To select the Clock Modes, skip to Step 3. To select the “Com
32、m” modes, push the white Clock/Comm button. * The “Comm” LED will light steadily, a “1” will flash in the “Mode” window, and a “P” will appear in the “Sched” window. Note: Once you select intercom programming, you can only select those “Comm” modes. To select the clock modes, you have to Erst exit t
33、o the Clock Run Mode, then begin again with Step 1. Step 3. To select a numbered mode (l-9, type in its number; to select a letter mode, press Funct while you type the corresponding number (“1” for “A,” “2” for “B,” etc.). * The number or letter you selected will show steady in the “Mode” window. Yo
34、u can now either enter a different mode or commence programming. General Methods Flashing, whether in a window or an entire group of LEDs, marks the spot (field) in the programming that will be affected by your entrles. We refer to this flashing area as the “flashing cursor.” Step 1. When you are in
35、 the desired mode, USC the cursor keys (+ and -*) to move to the desired window or LED group. Step 2. Use the digit keys to enter the desired program- ming. Keys 1-8 toggle the individual “Zones” and “Days” LEDs on and off. Step 3. Use the orange Clear key to restore a fields previous setting (excep
36、t in Mode B, where it is used to enter the entire series of numbers). When you are sure all the entries for the mode (or individual event) are correct, press the orange Enter key. * The new programming will be stored in the clocks memory, and the “Time” window and any involved LEDs will light steady
37、, to show your final entries. If you enter invalid data, such as “13” for the month, the 2524 will “beep” and flash the left-most field that had an error (for times and dates, the 2524 typically reverts to the last valid entry). Correct that field and press Enter, which will cause the 2524 to record
38、 this change and check for any other errors. If it finds one, it will flash that field. Note: In Modes 1 and 2, the 2524 will automatically advance to the next mode after you press Enter. Exiting To quit programming, return the cursor to the “Mode” window and type a “0” (Clock Run Mode). Alternative
39、ly, do nothing for one minute. In either case, the 2524 will return to the Clock Run Mode. Planning Information Needed Because of the interrelation between the wiring and the programming, a good deal of programming-related planning was required for the installation. You need the following informatio
40、n from that planning: 4 What is connected to each “Zone/Output” terminal (secondary clocks, equipment, etc.). 4 What, if any, secondary clock c o d e s are needed; if two are used, which is needed for Outputs 5 and 6, and which for Outputs 7 and 8. 4 How many relay panels are connected (O-20). Y 4 W
41、hether there is an audio program source that can be used for clock events (“Music”). v Whether there is a tone generator for clock tones. From the customer, you need to find out: The desired schedules for clock events, including holidays. The desired zones for clock events and intercom paging. The d
42、ates of the holidays and other special days for which a special schedule is desired. (You also need to know the dates for the changes to and from Daylight Savings Time.) The calling (“Architectural”) number that should be programmed for each room station (typically the same as the room number). Zone
43、s Chart When the 2524 is wired and used like a conventional master clock, you can easily figure out how its zones can be used. Any output connected to secondary clocks or to equipment can serve only them. However, wiring the 2524 to speakers via relay panels introduces a second type of zone, which i
44、s determined by the software in “Comm” Mode 2. Although these two types of zones work independently in some respects, they are closely interrelated: Which rooms should be included in the monitoring ? These software zones are used for both events and function. (When this function is activated by the
45、paging; thus, a page sent to Zone 4 will include the operator, it continuously cycles through the se- same speakers as a clock-tone event. lected stations, so that the operator can listen for any unusual sound that signals a need for action.) Most of this information can simply be entered in one or
46、two steps and, accordingly, will be explained in the appropriate “Modes” section of this manual. The events and the paging zones require more planning. Planning Charts Completing the charts attached to the end of this manual is an important part of planning. This will help you organize the programmi
47、ng, make it easier to enter the data, give the user helpful information, and simplify later programming changes. When you are Finished, provide copies to the users and keep a set for your own files. 4/90 Page 3 2524 ChronoCom Programming ?The eight zones are tied in with the 2524s “Zone/Output” term
48、inals. For example, if Outputs 7 and 8 are used for a clock-correction code, you cannot use Zones 7 and 8 for events (e.g., for send- ing clock tones via speakers). To have clock tones via speakers, the corresponding output terminals must be wired to the tone genera- tor, in or it can also be manually activated at any time. The Events Chart This chart contains the most columns and will typically have the largest number of entries. In order to fill
免费区 
