Qsc - Mx1000A 电路图.pdf

《Qsc - Mx1000A 电路图.pdf》由会员分享，可在线阅读，更多相关《Qsc - Mx1000A 电路图.pdf（2页珍藏版）》请在收音机爱好者资料库上搜索。

1、MX 1000a FEATURES A U D I O he MX 1000a is a high power, low profile pro- fessional power amplifier with advanced fea- tures and a flexible input. It delivers tremen- dous power in only two rack spaces, providing high level performance under the most demand- ing conditions. A stepped linear output c

2、ircuit combines high power with high efficiency to provide greater average and dynamic audio performance, while reducing normal system cooling and AC require- ments by greater than 40%. An automatic two- speed fan matches cooling capacity with ther- mal requirements. The rear panel uses Level 1 of Q

3、SCs exclusive Open Input Architecture which allows the use of optional input connectors, input transform- ers, cinema crossovers, power limiters, preci- sion attenuators, and other signal processing cards as they become available. 1675 MacArthur Boulevard Costa Mesa, California 92626-1468 USA Phone:

4、 714/754-6175 Fax: 714/754-6174 MXa Series LOADFTC CONTINUOUS AVERAGEEIA WATTS 20Hz-20kHz, 0.1% THD1kHz, 1% THD Stereo (W/Ch) 8250 watts275 watts 4350 watts400 watts 2500 watts* Mono-Bridged 16500 watts550 watts 8700 watts800 watts 41000 watts* *typical 500 watts per channel at 2 ohms 400 watts per

5、channel at 4 ohms Low profileOnly 2 rack spaces high High efficiency, 2-step output circuit for improved thermal performance and lower AC current consumption Split secondary configuration independent power supply on each channel, for greater reliability Quiet 2-speed fan Independent DC, sub audio sp

6、eaker protection one yellow LED signal indi- cator, triggering at -30 dB; a red LED showing true amplifier clipping; and a red LED which indicates muting when illuminated. The output connectors for each channel shall include a touch proof bind- ing post. The input connectors shall be mounted on a re

7、movable panel to permit upgrades. The standard input panel shall provide barrier strip and 1/4 connections for each channel. Inputs shall be electronically balanced, with a minimum impedance of 10 kilohms per side, and a common mode rejec- tion of at least 50 dB from 20 Hz to 20 kHz. The standard in

8、put panel shall contain switches for mono-bridging and parallel inputs, and solder pat- terns for input isolation transformers, gain reduction resistors, and first- order high and low pass filters . The input panel shall have enough space behind it to contain a circuit board measuring up to 5.9 wide

9、 by 4.1 “ deep. The multi-pin connector to the amplifier circuitry shall supply positive and negative DC supply cur- rents, and for each channel, balanced input signals, output signal, and clip/protect signal. Each channel shall be capable of meeting the following performance cri- teria with both ch

10、annels driven: Sine-wave output power of 250 watts into eight ohms, and 350 watts into four ohms, 20Hz to 20kHz, with less than O.1% THD. Frequency response at 3dB below rated power shall be 20Hz to 20kHz within O.15 dB. The voltage gain shall be 40, equivalent to 32dB, and the input sensitivity sha

11、ll be 1.12 Vrms. The signal to noise ratio over the range of 20 Hz to 20 kHz shall exceed 100 dB unweighted. IHF damping factor shall exceed 200. The amplifier chassis shall occupy two rack spaces, with provision for securing the rear corners. Depth from mounting surface to tips of rear supports sha

12、ll be 17.9 (45 5 cm). Weight shall not exceed 42 Ibs. (19.1 kg.). The amplifier shall be the QSC Audio Products Model MX 1000a. BACK MX 1000a Specifications A U D I O 1675 MacArthur Boulevard Costa Mesa, California 92626-1468 USA Phone: 714/754-6175 Fax: 714/754-6174 OUTPUT POWER (per channel) 8 ohm

13、s, 20 Hz to 20 kHz, 0.1%THD, 250 watts 8 ohms, 1kHz,1%THD, 275 watts 4 ohms, 20 Hz to 20 kHz, 0.1%THD, 350 watts 4 ohms, 1 kHz,1%THD, 400 watts 2 ohms, 1 kHz,1%THD, 500 watts* OUTPUT POWER (bridged mono) 8 ohms, 20 Hz to 20 kHz, 0.1%THD, 700 watts 4 ohms, 1 kHz,1%THD 1000 watts* *typical DISTORTION:

14、 SMPTE-IM, less than 0.05% FREQUENCY RESPONSE: 20 Hz to 20 kHz, 0.15 dB 8 Hz to 100 kHz, +0/-3 dB DAMPING FACTOR: Greater than 200 DYNAMIC HEADROOM: 3 dB at 4 ohms NOISE: 100 dB below rated output (20 Hz to 20 kHz) SENSITIVITY: 1.12 Vrms for rated power (8 ohms) VOLTAGE GAIN: 40 (32 dB) INPUT IMPEDA

15、NCE: 10K unbalanced, 20K balanced CONTROLS: Front: AC Switch, Ch 1 and Ch 2 Gain Knobs Back: Parallel/Stereo/Bridge Switch INDICATORS: PWR-ON:Green LED SIGNAL PRESENT: Yellow LED CLIP:Red LED PROT:Red LED CONNECTORS: (each channel) Input:Barrier strip and 1/4 RTS Speakers: Touch proof binding posts

16、COOLING: Two-speed fan, rear-to-front air flow. AMPLIFIER PROTECTION: Full short circuit, open circuit, ultrasonic, and RF protection. Stable into reactive or mismatched loads. LOAD PROTECTION: On/off muting. DC-fault load grounding relay with internal fault fuses. OUTPUT CIRCUIT TYPE: Complementary

17、 linear outputs, 2 step high efficiency circuit. POWER REQUIREMENTS: 100,120, 240 Vac, 50-60 Hz POWER CONSUMPTION: Normal Operation: 4 ohms per channel: less than 7.5 amps, 120 Vac (900 VA) maximum (full power, 2 ohms per channel): 22 amps, 120 Vac (2640 VA) DIMENSIONS: 19.0 (48.3 cm) rack mounting 3.5 (8.9 cm) tall (2 spaces) 17.9 (45.5 cm) deep (rear support ears) WEIGHT: 42 Ibs (19.1 kg) net, 49 Ibs (22.2 kg) shipping Output Averaging short circuit protection (US Patent 4,321,554) SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE. RadioFans.CN 收音机爱 好者资料库