《Qsc - Pl16Hvx 电路图.pdf》由会员分享，可在线阅读，更多相关《Qsc - Pl16Hvx 电路图.pdf（2页珍藏版）》请在收音机爱好者资料库上搜索。
1、FEATURES 1675 MacArthur Boulevard Costa Mesa, California 92626-1468 USA Ph: 714/754-6175 Fax: 714/754-6174 Web: E-mail: PowerLight? T PowerLightPowerLightPowerLightPowerLightPowerLight 1.61.61.61.61.6HVX HVXHVXHVXHVX he PowerLight 1.6HVX is an advanced dual power professional audio amplifier featuri
2、ng uncompromised audio performance. Designed specifically for use with bi-amplified speaker systems, power and performance of each channel is tailored for its intended load. A new high frequency power supply, utilizing QSCs PowerWave Switching Technology, has been combined with the rugged audio ampl
3、ification circuits of traditional QSC amplifiers to produce an amplifier with incredible audio performance, reliability, and thermal capacity. A special “High Voltage” output circuit provides maximum power at 16, 8, 4 ohm loads. The PowerLight 1.6HVX is rated at 725 watts/channel into 8 ohms and 110
4、0 watts/channel into 4 ohms for the low frequency channel, making it ideal for powering stage monitors and any high power, bi-amplified speaker systems. PowerWave Switching Technology provides increased power supply regulation to maintain excellent low frequency response to 20 Hz. Outstanding audio
5、performance and reliability, networkability, and light weight make this amplifier ideal for all critical sound system applications. Designed specifically for bi-amp applications 1100 watts (Low Frequency) at 4 725 watts (Low Frequency) at 8 450 watts (High Frequency) at 4 300 watt (High Frequency) a
6、t 8 (guaranteed minimum specs) Low Frequency channel features a high efficiency, Class H, 2-step output circuit for high power output, improved thermal performance and lower AC current consumption High Frequency channel features a full complementary class AB output circuit for ultra-low distortion a
7、nd smooth frequency response Advanced thermal management system Clip Limiter (user defeatable) reduces distortion, protects loud speakers PowerWave Switching Technologyfor improved audio performance Detented gain controls with 2 dB steps for easy resetting Comprehensive LED status arrays Two variabl
8、e speed fans, for quiet operation DC, sub audio, and thermal overload protection Patented Output Averaging short-circuit protection Neutrik ”Combo“ (XLR CH 2: 1.0 Vrms, for rated power (8 ohms) CONTROLS: Front: AC Switch, Ch 1 and Ch 2 Gain Knobs, Ch 1 and Ch 2 Clip Limiter Switches Back: Remote AC
9、Power Control Terminals VOLTAGE GAIN: CH 1: 63 (36 dB); CH 2: 50 (34 dB) INPUT IMPEDANCE: 10K unbalanced, 20K balanced INDICATORS: PROT:Red LEDCLIP:Red LED, 1 per ch. STANDBY:Yellow LEDLEVEL -10:Yellow LED, 1 per ch. PWR-ON:Green LEDLEVEL -20:Yellow LED, 1 per ch. SIG-PRESENT:Green LED, 1 per ch. CO
10、NNECTORS: (each channel) Input:Barrier strip and Neutrik “Combo” XLR and ” input Speakers:“Touch proof” binding posts Data Port:HD15 female COOLING: Two variable speed fans, rear-to-front air flow. AMPLIFIER PROTECTION: Full short circuit, open circuit, thermal, ultrasonic, and RF protection. Stable
11、 into reactive or mismatched loads. LOAD PROTECTION: On/off muting. DC-fault power supply shut down. OUTPUT CIRCUIT TYPE: CH 1: Complementary linear outputs. 2-step high efficiency circuit CH 2: Complementary linear outputs. Class AB circuit POWER REQUIREMENTS: 120, 230 VAC, 5060 Hz 120V CURRENT CON
12、SUMPTION: Multiply currents by 0.5 for 230V units*Pink noise DIMENSIONS: 19.0 (48.3 cm) rack mounting 3.5 (8.9 cm) tall (2 spaces) 17.9 (45.5 cm) deep (rear support ears) WEIGHT: 18 lbs (8.2 kg) net, 24 lbs (10.6 kg) shipping DAOL MARGORPLAMRON *REWOP8 / 1 MARGORPXAM REWOP3 / 1 EVAWENISXAM GNIPPI LC
13、%1 8 A3 . 5A6 . 9A5 . 61 4 A5 . 8A0 . 51A82 ARCHITECTS AND ENGINEERS SPECIFICATIONS The amplifier shall contain all solid-state circuitry, using complementary silicon output devices. The higher-powered of the two channels shall use a two- step Class H configuration and shall exceed the efficiency of
14、 an ordinary class-B linear output circuit. The lower-powered channel shall use a Class AB configuration. The amplifier shall operate from 5060 Hz AC power. The amplifier shall operate from a 15A 120V AC outlet, drawing less than 1025 VA when driven with random program material at 1/8 rated power in
15、to four ohm loads. The amplifier shall be supplied with a single molded AC cord having a standard NEMA 15 AC plug for 120 V units; 220240 V units shall be equipped with a 320-C19 16A IEC mains connector and a removable power cord. The amplifier shall comply with FCC part 15 Class B requirements. The
16、 amplifier shall employ forced-air cooling with two variable speed fans for minimum acoustic noise. Air flow shall be from rear to front to avoid tempera- ture rise inside the rack. Rack mounting shall be possible without clearance between amplifiers for ventilation. The amplifier shall be capable o
17、f continu- ous operation at 1/3 power into eight-ohm loads, in ambient temperatures up to 104F (40C). The amplifier shall contain two independent amplifier channels and a switching power supply. All amplifier protection systems shall be self- resetting upon removal of fault. Each channel shall have
18、protective cir- cuitry against short circuit or mismatched loads. Each channel shall moni- tor heat sink temperature and shall trigger fan speed boost, and if neces- sary, signal muting to prevent excessive temperature rise. Both channels shall have synchronized on-off muting, acting for three secon
19、ds after turn- on, and within second after turn-off or loss of AC power. Each channel shall have DC fault protection for the load, consisting of a power supply shutdown. Each channel shall have a user-defeatable clip limiter. The channels shall be configured for bi-amp usage, suitable for use with a
20、n external active crossover. Channel 1 shall be designated the “low frequency” channel, and Channel 2 the “high frequency” channel. The front panel shall contain the AC power switch; a green LED power-on indicator; a yellow LED standby indicator and a red protect mode indicator. Each channel shall h
21、ave the following controls and displays: a front panel detented gain control, with 11 gain settings (Low Frequency channel: 36 dB, 34 dB, 32 dB, 30 dB, 28 dB, 26 dB, 24 dB, 22 dB, 18 dB, 14 dB, -; High Frequncy channel: 34 dB, 32 dB, 30 dB, 28 dB, 26 dB, 24 dB, 22 dB, 20 dB, 16 dB, 12 dB, -); a rece
22、ssed front panel clip limiter defeat switch; a green signal present LED triggering at -30 dB; two yellow LED output indicators, triggering at -20 dB and -10 dB; a red LED showing true amplifier clipping. The output connectors for each channel shall be “touchproof” binding posts, accepting banana plu
23、gs or up to 7 AWG (4 mm dia.) wire. The rear panel input shall provide barrier strip and Neutrik “Combo” connectors for each channel. The XLR input shall be wired with pin 2 high, the TRS input shall be wired with tip positive, ring negative, and sleeve grounded. Inputs shall be electronically balan
24、ced, with a minimum impedance of 10 kilohms per side, and a common mode rejection of at least 50 dB from 20 Hz to 20 kHz. A High Density 15-pin Data Port connector shall carry both audio and amplifier operational status signals to and from a QSC MultiSignal Processor. A two-position barrier strip on
25、 the rear panel shall be used for remote Power Supply Enable; a contact closure shall place the both amplifier channels in standby mode, when the front panel power switch is in the on position. The front panel power switch shall function as a master switch that removes all AC power. The channels sha
26、ll be capable of meeting the following performance criteria with both channels driven: sine-wave output power of 725 watts (Low Fre- quency) and 275 watts (High Frequency) into 8 ohms, and 1100 watts (Low Frequency) and 500 watts (High Frequency) into 4 ohms, 20 Hz to 20 kHz, with less than 0.1% THD
27、. Frequency response at 3 dB below rated power shall be 20 Hz to 20 kHz within 0.15 dB. The voltage gain of the low frequency channel shall be 63, equivalent to 36 dB, and the input sensitivity shall be 1.12 Vrms. The voltage gain of the high frequency channel shall be 50, equivalent to 34 dB, and t
28、he input sensitivity shall be 1.0 Vrms. The signal to noise ratio over the range of 20 Hz to 20 kHz shall exceed 108 dB relative to full output. IHF damping factor shall exceed 350. The amplifier chassis shall occupy two rack spaces, with provision for securing the rear corners. Depth from mounting surface to tips of rear supports shall be 17.9 (45.5 cm). Weight shall not exceed 18 lbs. (8.2 kg.). The amplifier shall be the QSC Audio Products PowerLight 1.6HVX. RadioFans.CN 收音机爱 好者资料库
免费区 
