Aiwa-CX-JDS50-cs-sm 电路图 维修手册.pdf

《Aiwa-CX-JDS50-cs-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Aiwa-CX-JDS50-cs-sm 电路图 维修手册.pdf（70页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL Sony Corporation Personal Audio Group Published by Sony Engineering Corporation AEP Model CX-JDS20 E Model CX-JDS20/JDS50 Australian Model CX-JDS20 Russian Model CX-JDS20/JDS50 COMPACT DISC DECK RECEIVER 9-879-515-01 2005C1678-1 2005.03 Ver. 1.0 2005.03 SPECIFICATIONS CX-JDS20/JDS50 C

2、X-JDS20/JDS50 are the Amplifier, CD player, Tape Deck and Tuner section in DBX-DS20/DBX-DS50. Continued on next page Model Name Using Similar MechanismNEW CD CD Mechanism TypeBU-F1BD81A Section Optical Pick-up NameKSM-215DCP/C2NP TAPE Model Name Using Similar MechanismCX-LEM330 SectionTape Transport

3、 Mechanism Type JDS20CMAL5Z220A JDS50CMAL1Z240A Photo : CX-JDS50 Other models: JDS50 The following measured at AC 120, 127, 220, 240 V 50/60 Hz DIN power output (rated): 160 + 160 watts (6 ohms at 1 kHz, DIN) Continuous RMS power output (reference): 200 + 200 watts (6 ohms at 1 kHz, 10% THD) JDS20 T

4、he following measured at AC 120, 127, 220, 240 V 50/60 Hz DIN power output (rated): 96 + 96 watts (6 ohms at 1 kHz, DIN) Continuous RMS power output (reference): 120 + 120 watts (6 ohms at 1 kHz, 10% THD) Inputs AUDIO IN (stereo mini jack): voltage : impedance 47 kilohms MIC (phone jack) (except for

5、 European model): se JDS20: 0.25 mV JDS50: 0.1 mV, nsitivity: impedance 10 kilohms Outputs PHONES (stereo mini jack): accepts headphones of 8 ohms or more SPEAKER:accepts impedance of 6 to 16 ohms Amplifier section European model: JDS20 DIN power output (rated): 96 + 96 watts (6 ohms at 1 kHz, DIN)

6、Continuous RMS power output (reference): 120 + 120 watts (6 ohms at 1 kHz, 10% THD) Music power output (reference): 180 + 180 watts (6 ohms at 1 kHz, 10% THD) Russian model: JDS50 DIN power output (rated): 160 + 160 watts (6 ohms at 1 kHz, DIN) Continuous RMS power output (reference): 200 + 200 watt

7、s (6 ohms at 1 kHz, 10% THD) Music power output (reference): 330 + 330 watts (6 ohms at 1 kHz, 10% THD) JDS20 DIN power output (rated): 96 + 96 watts (6 ohms at 1 kHz, DIN) Continuous RMS power output (reference): 120 + 120 watts (6 ohms at 1 kHz, 10% THD) Music power output (reference): 180 + 180 w

8、atts (6 ohms at 1 kHz, 10% THD) JDS20: 1.85 V JDS50: 0.9 V, RadioFans.CN 收音机爱 好者资料库 2 CX-JDS20/JDS50 SAFETY-RELATED COMPONENT WARNING! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS W

9、ITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. General Power requirements European and Russian models: 230 V AC, 50/60 Hz Australian model:230 240 V AC, 50/60 Hz Argentine model:220 V AC, 50/60 Hz Mexican model:127 V AC, 60 Hz Other models:120 V

10、, 220 V or 230 240 V AC, 50/60 Hz Adjustable with voltage selector Power consumption European model: JDS20:198 watts 0.25 watts (at the Power Saving Mode) Other models: JDS50:160 watts JDS20:198 watts Dimensions (w/h/d) (excl. speakers): Approx. 230 365.5 409 mm Mass (excl. speakers)Approx. 9.1 kg D

11、esign and specifications are subject to change without notice. CD player section SystemCompact disc and digital audio system Laser Diode PropertiesEmission duration: continuous Laser Output: Less than 44.6 W (This output is the value measurement at a distance of 200 mm from the objective lens surfac

12、e on the Optical Pick-up Block with 7 mm aperture) Frequency response2 Hz 20 kHz (0.5 dB) Signal-to-noise ratioMore than 90 dB Dynamic rangeMore than 90 dB Tape deck section Recording system4-track 2-channel, stereo Frequency response50 13,000 Hz (3 dB), using Sony TYPE I cassettes Tuner section FM

13、stereo, FM/AM superheterodyne tuner FM tuner section Tuning range87.5 108.0 MHz (50 kHz step) AntennaFM lead antenna Antenna terminals75 ohms unbalanced Intermediate frequency10.7 MHz AM tuner section Tuning range European and Russian models: 531 1,602 kHz (with the tuning interval set at 9 kHz) Oth

14、er models:530 1,710 kHz (with the tuning interval set at 10 kHz) 531 1,602 kHz (with the tuning interval set at 9 kHz) AntennaAM loop antenna Antenna terminalsExternal antenna terminal Intermediate frequency450 kHz Pan-American models:530 1,710 kHz (with the tuning interval set at 10 kHz) 531 1,710

15、kHz (with the tuning interval set at 9 kHz) Abbreviation AUS: Australian model E51: Chilean and Peruvian models MX: Mexican model RU: Russian model ModelPart No. JDS50: MX model2-595-343-0 JDS20: MX model2-595-345-0 JDS50: E51 model2-595-523-0 JDS20: E51 model2-595-525-0 JDS50: RU model2-599-602-0 J

16、DS20: AEP, RU models2-599-608-0 JDS20: AUS model2-599-613-0 MODEL IDENTIFICATION BACK PANEL 3 # # 3 Part No. RadioFans.CN 收音机爱 好者资料库 3 CX-JDS20/JDS50 The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the charged electros

17、tatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK

18、The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pick- up block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens. NOTES ON HANDLING THE OPTICAL PICK-UP BLO

19、CK OR BASE UNIT Notes on chip component replacement Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor may be damaged by heat. Flexible Circuit Board Repairing Keep the temperature of the soldering iron around 270 C during repairing. Do not touch the solder

20、ing iron on the same conductor of the circuit board (within 3 times). Be careful not to apply force on the conductor when soldering or unsoldering. CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. UNLEAD

21、ED SOLDER Boards requiring use of unleaded solder are printed with the lead- free mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size) : LEAD FREE MARK Unleaded solder has the following char

22、acteristics. Unleaded solder melts at a temperature about 40 C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350 C. Caution: The

23、 printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! Strong viscosity Unleaded solder is more viscou-s (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. Usable with ordinary sold

24、er It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. Laser component in this product is capable of emitting radiation exceeding the limit for Class 1. This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located

25、on the exterior. The release method of a CD disc tray LOCK function There is a disc lock function for the disc theft prevention for a demonstration at a shop front in this machine. Procedue: 1.Press the ?/1 button to turn the set on. 2.Press two buttons of x and Z simultaneously for five seconds. 3.

26、The message “LOCKED” is displayed and the tray is locked. (Even if exiting from this mode, the tray is still locked.) 4.Press two buttons of x and Z simultaneously for five seconds again. 5.The message “UNLOCKED” is displayed and the tray is unlocked. 6.To exit from this mode, press the ?/1 button t

27、o turn the set off. RadioFans.CN 收音机爱 好者资料库 4 CX-JDS20/JDS50 TABLE OF CONTENTS 1.GENERAL.5 2.DISASSEMBLY 2-1.Disassembly Flow .7 2-2.Top Panel, Side Panel .8 2-3.Front Section .8 2-4.CD Mechanism Section.9 2-5.Cassette Mechanism Deck, DS-PAI/HP/MIC Board .9 2-6.DS-PANEL Board . 10 2-7.Rear Cabinet .

28、 10 2-8.Power Trans . 11 2-9.DS-MAIN Board, Heat Sink . 11 2-10. Holder (CD Mech). 12 2-11. Base Unit (BU-F1BD81A), CD Mech . 12 2-12. BD Board, Optical Pick-up (KSM-215DCP/C2NP) . 13 2-13. Frame. 13 2-14. Belt . 14 2-15. Cassette Panel. 15 3.TEST MODE. 16 4.MECHANICAL ADJUSTMENTS. 17 5.ELECTRICAL A

29、DJUSTMENTS. 17 6.DIAGRAMS 6-1.Block Diagram MAIN Section . 22 BD Section . 23 6-2.Printed Wiring Board BD Section . 24 6-3.Schematic Diagram BD Section . 25 6-4.Printed Wiring Board MAIN (JDS20) Section . 26 6-5.Printed Wiring Board MAIN (JDS50) Section . 27 6-6.Schematic Diagram MAIN Section (1/2)

30、. 28 6-7.Schematic Diagram MAIN Section (2/2) . 29 6-8.Printed Wiring Board PANEL (JDS20/JDS50) Section . 30 6-9.Schematic Diagram PANEL Section (1/2) . 31 6-10. Schematic Diagram PANEL Section (2/2) . 32 6-11. Printed Wiring Board PANEL COMB (JDS20) Section . 33 6-12. Printed Wiring Board PANEL COM

31、B (JDS50) Section . 34 6-13. Schematic Diagram PANEL COMB Section . 35 6-14. Printed Wiring Board AMP (JDS20) Section . 36 6-15. Printed Wiring Board AMP (JDS50) Section . 37 6-16. Schematic Diagram AMP (JDS20) Section . 38 6-17. Schematic Diagram AMP (JDS50) Section . 39 6-18. Printed Wiring Board

32、POWER (JDS20/JDS50) Section . 40 6-19. Schematic Diagram POWER Section . 41 7.EXPLODED VIEWS 7-1.Overall Section . 50 7-2.Front Section . 51 7-3.Chassis Section. 52 7-4.CD Mechanism Section-1 . 53 7-5.CD Mechanism Section-2 . 54 8.ELECTRICAL PARTS LIST. 55 5 CX-JDS20/JDS50 SECTION 1 GENERAL This sec

33、tion is extracted from instruction manual. Main unit AUDIO IN jack w; (28) BASS control qf (21) CANCEL wl (11) CD SYNC wk (18) Cassette compartment qh (17) DISC 1 3 4 (10) DISC SKIP/EX-CHANGE 5 (10, 13, 18) Disc tray 6 (9) DISPLAY qd (16, 25, 26) Display window 3 ENTER wf (11, 13, 14) EQ 0 (20) FM M

34、ODE wd (16) FUNCTION wj (9, 13, 14, 15, 17, 18, 19, 21, 28) i-Bass 9 (20, 31) MIC jack1) qj (21) MIC LEVEL1) qk (21) MIDDLE control qs (21) Jog dial ws (11, 13) PHONES jack ql PLAY MODE wg (10, 13, 17) REC PAUSE/START 8 (18, 19, 21) Remote sensor 2 REP wd (12) TREBLE control qa (21) TUNER/BAND wh (1

35、4, 15) TUNING +/ wl (14, 15) TUNING MODE wg (14, 15) VOLUME control wa (27) ?/1 (power) 1 (7, 15) Z (eject) 7 (9) Z PUSH (eject) qg (17) lm/ML (rewind/fast forward, go back/go forward) wl (10, 17) x (stop) wl (10, 17, 18, 21, 27, 31) N2) or nN3) (play) wl (10, 17, 18) X (pause) wl (10, 17, 31) 1)Exc

36、ept for European model 2)DBX-DS20 3)DBX-DS50 List of button locations and reference pages How to use this page Use this page to find the location of buttons and other parts of the system that are mentioned in the text. Illustration number r TUNER/BAND wh (14, 15) RR Name of button/partReference page

37、 ALPHABETICAL ORDER A NM Z BUTTON DESCRIPTIONS qf w; ql qg qh qk qj wd wa ws wf wg wj wh wk wl 1762 354 8 9 0 qa qs qd 6 CX-JDS20/JDS50 Remote control CD qk (9, 12) CLEAR qg (13) CLOCK/TIMER SELECT 2 (24, 25) CLOCK/TIMER SET 3 (8, 23, 24) DISC SKIP q; (10, 12) DISPLAY wa (16, 25, 26) ENTER 9 (8, 12,

38、 14, 23, 24) EQ qf (20) FM MODE 4 (16) FOLDER + qa (10, 12, 18) FOLDER qd (10, 12, 18) FUNCTION 6 (9, 12, 14, 15, 17, 28) PLAY MODE w; (10, 12, 17) REPEAT 4 (12) SLEEP ws (23) TAPE qj (17) TUNER BAND 5 (14, 15) TUNER MEMORY ql (14) TUNING MODE w; (14, 15) VOLUME +/ qs (23) ?/1 (power) 1 (7, 24) m/M

39、(rewind/fast forward) 7 (10, 17) N (play) 8 (10, 17) X (pause) 8 (10, 17) x (stop) 8 (10, 17) +/ (tuning) qh (14) ./ (go back/go forward) qh (8, 10, 23) ALPHABETICAL ORDER A EF Z BUTTON DESCRIPTIONS 4 5 6 7 8 9 q; ws1 qd qg qf wa w; ql qk qj qh qa qs 3 2 Use buttons on the remote for the operation.

40、1Press ?/1 to turn on the system. 2Press CLOCK/TIMER SET. 3Press . or repeatedly to set the hour. 4Press ENTER. 5Press . or repeatedly to set the minute. 6Press ENTER. The clock starts working. To adjust the clock 1Press CLOCK/TIMER SET. 2Press . or repeatedly to select “CLOCK SET”, then press ENTER

41、. 3Do the same procedures as step 3 to 6 above. Notes The clock settings are canceled when you disconnect the power cord or if a power failure occurs. You cannot set the clock in Power Saving Mode (page 25). Setting the clock 7 CX-JDS20/JDS50 SECTION 2 DISASSEMBLY 2-1.DISASSEMBLY FLOW This set can b

42、e disassembled in the order shown below. SET 2-2. TOP PANEL, SIDE PANEL (Page 8) 2-15. CASSETTE PANEL (Page 15) 2-3. FRONT SECTION (Page 8) 2-7. REAR CABINET (Page 10) 2-10. HOLDER (CD MECH) (Page 12) 2-14. BELT (Page 14) 2-8. POWER TRANS (Page 11) 2-11. BASE UNIT (BU-F1BD81A), CD MECH (Page 12) 2-4

43、. CD MECHANISM SECTION (Page 9) 2-6. DS-PANEL BOARD (Page 10) 2-5. CASSETTE MECHANISM DECK, DS-PAI/HP/MIC BOARD (Page 9) 2-9. DS-MAIN BOARD, HEAT SINK (Page 11) 2-13. FRAME (Page 13) 2-12. BD BORD, OPTICAL PICK-UP (KSM-215DCP/C2NP) (Page 13) 8 CX-JDS20/JDS50 Note: Follow the disassembly procedure in

44、 the numerical order given. 2-2.TOP PANEL, SIDE PANEL 2-3.FRONT SECTION qatop panel 2two screws (+BVTP 3 10) 5two screws (+BVTP 3 10) 7three screws (+BVTP 3 10) 3right panel 6left panel 1four screws (Case 3) 4four screws (Case 3) q; 9 8 9front section 5three screws (+BVTP)(B3) 6screw (+BVTP)(B3) 8screw (+BVTP