Aiwa-NSXAJ17-cs-sm 电路图 维修手册.pdf

《Aiwa-NSXAJ17-cs-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Aiwa-NSXAJ17-cs-sm 电路图 维修手册.pdf（32页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL DATA COMPACT DISC STEREO CASSETTE RECEIVER BASIC TAPE MECHANISM : ZZM-2 PR1NM BASIC CD MECHANISM : AZG-1 ZA3RDM, AZG-1 ZA3RNDM NSX-AJ17 NSX-BL14 U LH S/M Code No. 09-003-428-8R1 REVISION If requiring information about the CD mechanism, see Service Manual of AZG-1, (S/M Code No. 09-001

2、-335-3NC). This Service Manual is the “Revision Publishing” and replaces “Simple Manual” NSX-AJ17(U)/BL14(LH), (S/M Code No. 09-001-428-8T1). SPEAKER REMOTE CONTROLLER RC-ZAS02 NSX-AJ17 SYSTEM CD CASSEIVER NSX-BL14 CX-NAJ17SX-NAJ17 CX-NBL14SX-NBL17 CD MECHANISM AZG-1 ZA3RNDM AZG-1 ZA3RDM RadioFans.C

3、N 收音机爱 好者资料库 2 Tuning range87.5 MHz to 108 MHz Usable sensitivity (IHF)13.2 dBf Antenna terminals75 ohms (unbalanced) Tuning range530 kHz to 1710 kHz (10 kHz step) 531 kHz to 1602 kHz (9 kHz step) Usable sensitivity350 V/m AntennaLoop antenna Power outputRated U: 30 W + 30 W (50 Hz - 20 kHz, THD les

4、s than 1%, 6 ohms) LH: 28 W + 28 W (1 kHz, THD 1%, 6 ohms) Reference U: 40 W + 40 W (1 kHz, THD less than 10%, 6 ohms) LH: 35 W + 35 W (1 kHz, THD 10% 6 ohms) Total harmonic distortion U: 0.1% (15 W, 1 kHz, 6 ohms, DIN AUDIO) LH: 0.1% (14 W, 1 kHz, 6 ohms, DIN AUDIO) InputsVIDEO/AUX: 500 mV OutputsS

5、PEAKERS: accept speakers of 6 ohms or more SURROUND SPEAKERS accept speakers of 8 ohms to 16 ohms PHONES (stereo jack) : accepts headphones of 32 ohms or more Track format4 tracks, 2 channels stereo Frequency response50 Hz 8000 Hz Recording systemAC bias HeadsDeck 1 : Recording/Playback head x 1, er

6、ase head x 1 Deck 2 : Playback head x 1 LaserSemiconductor laser ( =780 nm) D-A converter1 bit dual Signal-to-noise ratio85 dB (1 kHz, 0 dB) Harmonic distortion0.05 % (1 kHz, 0 dB) SPECIFICATIONS SX-NAJ17 Speaker System2 way, bass reflex (magnetic shielded type) Speaker unitsWoofer: 120 mm (43/4 in.

7、) cone type Tweeter: 20mm (13/16 in.) cone type Impedance6 ohms Sensitivity86 dB/W/m Dimensions (W x H x D)220 x 324x 211 mm (83/4 x 127/8 x 83/8 in.) Weight2.0 kg (4 lbs 7 oz.) SX-NBL17 Speaker System2 way, bass reflex (magnetic shielded type) Speaker unitsWoofer: 120 mm cone type Tweeter: 20mm con

8、e type Impedance6 ohms Sensitivity87 dB/W/m Dimensions (W x H x D)220 x 324x 211 mm Weight2.0 kg Power requirementsU: 120 V AC, 60 Hz LH: 120 V/220-230 V/240 V AC (switchable), 50/60 Hz Power consumptionU: 60 W LH: 55 W Power consumptionWith power-economizing in standby modemode off : 12 W With powe

9、r-economizing mode on : 0.9 W Dimensions of main unitU: (W x H x D)260 x 330 x 348 mm (101/4 X 13 X 133/4 in.) LH: 260 x 324 x 348 mm Weight of main unitU: 5.7 kg (12 lbs 9 oz.) LH: 5.7 kg Design and specifications are subject to change without notice. RadioFans.CN 收音机爱 好者资料库 3 CLASS 1LASER PRODUCT

10、KLASSE 1LASER PRODUKT LUOKAN 1LASER LAITE KLASS 1LASER APPARAT This set employs laser. Therefore, be sure to follow carefully the instructions below when servicing. WARNING! WHEN SERVICING, DO NOT APPROACH THE LASER EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMISSIO

11、N. BE SURE TO OBSERVE FROM A DISTANCE OF MORE THAN 30cm FROM THE SURFACE OF THE OBJEC- TIVE LENS ON THE OPTICAL PICK-UP BLOCK. sCaution: Invisible laser radiation when open and interlocks defeated avoid exposure to beam. sAdvarsel: Usynlig laserstling ved bning, nr sikkerhedsafbrydere er ude af funk

12、tion. Undg udsttelse for strling. VAROITUS! Laiteen Kyttminen muulla kuin tss kyttohjeessa mainitulla tavalla saattaa altistaa kyt-tjn turvallisuusluokan 1 ylittvlle nkymttmlle lasersteilylle. VARNING! Om apparaten anvnds p annat stt n vad som specificeras i denna bruksanvising, kan anvndaren utstta

13、s fr osynling laserstrlning, som verskrider grnsen fr laserklass 1. PROTECTION OF EYES FROM LASER BEAM DURING SERVICING CAUTION Use of controls or adjustments or performance of proce- dures other than those specified herein may result in hazardous radiation exposure. ATTENTION Lutillisation de comma

14、ndes, rglages ou procdures autres que ceux spcifis peut entraner une dangereuse exposition aux radiations. ADVARSEL Usynlig laserstling ved bning, nr sikkerhedsafbrydereer ude af funktion. Undg udsttelse for strling. This Compact Disc player is classified as a CLASS 1 LASER product. The CLASS 1 LASE

15、R PRODUCT label is located on the rear exterior. PICK-UP ASSY P.C.B Precaution to replace Optical block (KSS-213F) Body or clothes electrostatic potential could ruin laser diode in the optical block. Be sure ground body and workbench, and use care the clothes do not touch the diode. 1) After the con

16、nection, remove solder shown in right figure. SOLDER RadioFans.CN 收音机爱 好者资料库 4 NOTE ON BEFORE STARTING REPAIR Charging voltage (V)Discharging Rated power (W)Parts number (C101, 102)resistor () 25-48100387-A00-247-090 49-140220587-A00-232-090 Note: The reference numbers (C101, C102) of the electrolyt

17、ic capacitors can change depending on the models. Be sure to check the reference numbers of the charging capacitors on schematic diagram before starting the discharging work. 2. Check items before exchanging the MICROCOMPUTER Be sure to check the following items before exchanging the MICROCOMPUTER.

18、Exchange the MICROCOMPUTER after confirming that the MICROCOMPUTER is surely defective. 2-1. Regarding the HOLD terminal of the MICROCOMPUTER When the HOLD terminal (INPUT) of the MICROCOMPUTER is “H”, the MICROCOMPUTER is judged to be operating correctly. When this terminal is “L”, the main power c

19、annot be turned on. Therefore, be sure to check the terminal voltage of the HOLD terminal before exchange. When the MICROCOMPUTER is not defective, the HOLD terminal can also go “L” when the POWER AMPLIFIER has any abnormalities that triggers the abnormality detection circuit on the MAIN C. B. that

20、sets the HOLD terminal to “L”. Good or no good judgement of the MICROCOMPUTER 11111Turn on the AC main power. 22222Confirm that the main power is turned on and the HOLD terminal of the MICROCOMPUTER keeps the “H” level or not. 33333When the HOLD terminal is “L” level, the abnormality detection circu

21、it is judged to be working correctly and the MICROCOMPUTER is judged to be good. 1. Forced discharge of electrolytic capacitor of power supply block When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across the electr

22、olytic capacitors (C101, 102) even though AC power cord is removed. If repair is attempted in this condition, secondary defect can occur. In order to prevent the secondary trouble, perform the following measures before starting repair work. Discharge procedure 11111Remove the AC power cord. 22222Con

23、nect a discharging resistor at an end of lead wire that has clips at both ends. Connect the other end of the lead wire to metal chassis. 33333Contact the other end of the discharging resistor to the positive (+) side (+VH) of C101. (For two seconds) 44444Contact the same end of the discharging resis

24、tor as step 33333 to the negative (-) side (-VH) of C102 in the same way. (For two seconds) 55555Check that voltage across C101 and C102 has decreased to 1 V or less using a multimeter or an oscilloscope. Select a discharging resistor referring to the following table.Fig-1 MAIN C.B D101 C101C102 22

25、34 5 In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not. 2-2. Regarding reset There are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC power cord is re-inserted, or the software rese

26、t (pressing the STOP key + POWER key) is performed. When the above described phenomenon occurs, it can lead to wrong judgement as if the MICROCOMPUTER is defective and to exchange the MICROCOMPUTER. In such a case, perform the forced-reset by the following procedure and check good or no good of the

27、MICROCOMPUTER. 11111Remove the AC power cord. 22222Short both ends of the electrolytic capacitor C113 that is connected to VDD of the MICROCOMPUTER with tweezers. 33333Connect the AC power cord again. If the MICROCOMPUTER returns to the normal operation, the MICROCOMPUTER is good. Note: The referenc

28、e number or MICROCOMPUTER pin number of transistor (Q110) and electrolytic capacitor (C113) can change depending on the models. Be sure to check the reference numbers on schematic diagram before starting the discharging work. 2-3. Confirmation of soldering state of MICROCOMPUTER Check the soldering

29、state of the MICROCOMPUTER in addition to the above described procedures. Be sure to exchange the MICROCOMPUTER after surely confirming that the trouble is not caused by poor soldering but the MICROCOMPUTER itself. Fig-2-2 MICRO- COMPUTER MICROCOMPUTER FRONT C.B FRONT C.B VSS VDD C113 * % C113 18 15

30、 Short with tweezers. 6 ELECTRICAL MAIN PARTS LIST DESCRIPTIONREF. NO.KANRI NO. PART NO.DESCRIPTIONREF. NO.KANRI NO. PART NO. IC 8A-NFA-615-010 C-IC,M38B57MCH-E236FP 87-A21-397-010 IC,STK490-070 87-A21-629-010 IC,SPS-442-1-N 87-A21-419-040 C-IC,NJM14558MD-TE2 87-A21-443-040 C-IC,M62495AFP 87-A21-415

31、-010 IC,LA1843 87-070-127-110 IC,LC72131 D TRANSISTOR 87-026-609-080 TR,KTA1266GR 89-213-702-010 TR,2SB1370 (1.8W) 87-026-610-080 TR,KTC3198GR 87-A30-076-080 C-TR,2SC3052F 87-A30-075-080 C-TR,2SA1235F 87-026-245-080 TR,DTC114ES 87-A30-198-080 TR,KTC3199GR 87-A30-090-080 FET,2SK2541 87-A30-484-080 C-

32、TR,KRA102S 87-A30-468-080 C-TR,KRC102S-RTK 87-A30-107-070 C-TR,CMBT5401 87-A30-106-040 C-TR,CMBT5551 87-A30-091-080 FET,2SJ460 87-A30-062-080 C-TR,KRC104S 87-A30-318-080 TR,CSA952K 89-333-317-880 TR,2SC3331 (0.5W) 87-A30-234-080 TR,CSC4115BC 89-327-143-080 TR,2SC2714 (0.1W) 87-A30-489-080 C-TR,KRA10

33、7S DIODE 87-020-465-080 DIODE,1SS133 (110MA) 87-A40-393-090 DIODE,1N5402GW(F20) 87-A40-455-080 DIODE,RL203 GW 87-A40-553-080 DIODE,1N4003 LES 87-A40-774-080 ZENER,UZ24BSD 87-A40-764-080 ZENER,UZ10BSC 87-A40-313-080 C-DIODE,MC 2840 87-A40-270-080 C-DIODE,MC2838 87-A40-269-080 C-DIODE,MC2836 87-A40-76

34、8-080 ZENER,UZ16BSA 87-A40-752-080 ZENER,UZ6.2BSC 87-A40-739-080 ZENER,UZ2.7BSA 87-017-149-080 ZENER,HZS6A2L MAIN C.B C3 87-010-196-080 CHIP CAPACITOR,0.1-25 C4 87-010-196-080 CHIP CAPACITOR,0.1-25 C5 87-010-196-080 CHIP CAPACITOR,0.1-25 C6 87-010-196-080 CHIP CAPACITOR,0.1-25 C9 87-010-196-080 CHIP

35、 CAPACITOR,0.1-25 C10 87-010-196-080 CHIP CAPACITOR,0.1-25 C11 87-010-196-080 CHIP CAPACITOR,0.1-25 C12 87-010-196-080 CHIP CAPACITOR,0.1-25 C19 87-A10-627-000 CAP,E 2200-50 M SMG C20 87-A10-627-000 CAP,E 2200-50 M SMG C21 87-016-495-000 CAP,E 3300-25 M SMG C22 87-016-495-000 CAP,E 3300-25 M SMG C25

36、 87-010-385-080 CAP, ELECT 220-25V C26 87-010-247-080 CAP, ELECT 100-50V C30 87-010-247-080 CAP, ELECT 100-50V C31 87-010-263-080 CAP, ELECT 100-10V C32 87-010-197-080 CAP, CHIP 0.01 DM C33 87-010-263-080 CAP, ELECT 100-10V C34 87-010-247-080 CAP, ELECT 100-50V C35 87-010-406-080 CAP, ELECT 22-50 C3

37、6 87-010-381-080 CAP, ELECT 330-16V C38 87-A11-567-080 C-CAP,S 0.01-50 K B C60 87-010-403-080 CAP, ELECT 3.3-50V C97 87-010-196-080 CHIP CAPACITOR,0.1-25 C100 87-018-127-080 CAP TC-U 470P C101 87-010-183-080 C-CAP,S 2700P-50 B C102 87-010-183-080 C-CAP,S 2700P-50 B C103 87-010-545-080 CAP, ELECT 0.2

38、2-50V C104 87-010-545-080 CAP, ELECT 0.22-50V C105 87-010-178-080 CHIP CAP 1000P C106 87-010-178-080 CHIP CAP 1000P C107 87-010-404-080 CAP, ELECT 4.7-50V C108 87-010-404-080 CAP, ELECT 4.7-50V C111 87-010-391-080 CAP,E 10-35 SME C112 87-010-391-080 CAP,E 10-35 SME C113 87-010-405-080 CAP, ELECT 10-

39、50V C114 87-010-405-080 CAP, ELECT 10-50V C119 87-010-197-080 CAP, CHIP 0.01 DM C120 87-010-197-080 CAP, CHIP 0.01 DM C125 87-012-368-080 C-CAP,S 0.1-50 F C126 87-012-368-080 C-CAP,S 0.1-50 F C127 87-012-368-080 C-CAP,S 0.1-50 F C128 87-012-368-080 C-CAP,S 0.1-50 F C129 87-A11-572-080 C-CAP,S 0.015-

40、50 K B C130 87-A11-572-080 C-CAP,S 0.015-50 K B C131 87-010-197-080 CAP, CHIP 0.01 DM C132 87-010-197-080 CAP, CHIP 0.01 DM C133 87-010-186-080 CAP,CHIP 4700P C140 87-010-182-080 C-CAP,S 2200P-50 B C183 87-010-387-080 CAP,E 470-25 SME C200 87-018-195-080 CAP TC-U 1200P C235 87-010-408-080 CAP, ELECT

41、 47-50V C236 87-010-408-080 CAP, ELECT 47-50V C300 87-018-195-080 CAP TC-U 1200P C301 87-010-179-080 CAP,CHIP S B1200P C302 87-010-179-080 CAP,CHIP S B1200P C303 87-010-178-080 CHIP CAP 1000P C304 87-010-178-080 CHIP CAP 1000P C305 87-010-198-080 CAP, CHIP 0.022 C307 87-010-263-080 CAP, ELECT 100-10

42、V C308 87-010-263-080 CAP, ELECT 100-10V C311 87-010-598-080 C-CAP,S 0.068-16VRK C312 87-010-598-080 C-CAP,S 0.068-16VRK C313 87-010-188-080 CAP,CHIP 6800P C314 87-010-188-080 CAP,CHIP 6800P C315 87-010-263-080 CAP, ELECT 100-10V C317 87-010-546-080 CAP, ELECT 0.33-50V C318 87-010-546-080 CAP, ELECT

43、 0.33-50V C326 87-010-198-080 CAP, CHIP 0.022 C327 87-010-196-080 CHIP CAPACITOR,0.1-25 C360 87-010-401-080 CAP, ELECT 1-50V C399 87-012-140-080 CAP 470P C401 87-010-544-080 CAP, ELECT 0.1-50V C402 87-010-544-080 CAP, ELECT 0.1-50V C405 87-010-197-080 CAP, CHIP 0.01 DM C406 87-010-197-080 CAP, CHIP

44、0.01 DM C407 87-010-197-080 CAP, CHIP 0.01 DM C408 87-010-197-080 CAP, CHIP 0.01 DM C409 87-010-182-080 C-CAP,S 2200P-50 B C410 87-010-182-080 C-CAP,S 2200P-50 B C411 87-010-405-080 CAP, ELECT 10-50V C412 87-010-405-080 CAP, ELECT 10-50V C452 87-010-382-080 CAP, ELECT 22-25V C453 87-010-183-080 C-CA

45、P,S 2700P-50 B C454 87-010-183-080 C-CAP,S 2700P-50 B C455 87-010-183-080 C-CAP,S 2700P-50 B C456 87-010-197-080 CAP, CHIP 0.01 DM C460 87-010-196-080 CHIP CAPACITOR,0.1-25 C461 87-012-158-080 C-CAP,S 390P-50 CH C462 87-012-158-080 C-CAP,S 390P-50 CH 7 DESCRIPTIONREF. NO.KANRI NO. PART NO.DESCRIPTIO

46、NREF. NO.KANRI NO. PART NO. C605 87-010-179-080 CAP,CHIP S B1200P C606 87-010-179-080 CAP,CHIP S B1200P C609 87-010-213-080 C-CAP,S 0.015-50 B C610 87-010-213-080 C-CAP,S 0.015-50 B C611 87-010-545-080 CAP, ELECT 0.22-50V C612 87-010-545-080 CAP, ELECT 0.22-50V C613 87-010-545-080 CAP, ELECT 0.22-50

47、V C614 87-010-545-080 CAP, ELECT 0.22-50V C615 87-010-154-080 CAP CHIP 10P C616 87-010-385-080 CAP, ELECT 220-25V C617 87-010-385-080 CAP, ELECT 220-25V C618 87-010-405-080 CAP, ELECT 10-50V C630 87-016-669-080 C-CAP,S 0.1-25 K B C669 87-010-322-080 C-CAP,S 100P-50 CH C670 87-010-322-080 C-CAP,S 100P-50 CH C677 87-010-197-080 CAP, CHIP 0.01 DM C771 87-010-263-080 CAP, ELECT 100-10V C772 87-010-197-080 CAP, CHIP 0.01 DM C782 87-010-197-080 CAP, CHIP 0.01 DM C783 87-010-197-080 CAP, CHIP 0.01 DM C784 87-010-197-080 CAP, CHIP 0.01 DM C785 87-010-197-080 CAP, CHIP