Aiwa-NSXT929-cs-sm 电路图 维修手册.pdf

《Aiwa-NSXT929-cs-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Aiwa-NSXT929-cs-sm 电路图 维修手册.pdf（43页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL DATA NSX-T929RC-ZAS04 SYSTEM CD CASSEIVER REMOTE CONTROLLER CX-NT929 COMPACT DISC STEREO SYSTEM BASIC TAPE MECHANISM : 2ZM-3MK2 PR7NM BASIC CD MECHANISM : 6ZG-1 ZZRNDM NSX-T929LH S/M Code No. 09-013-440-2R1 This Service Manual is the “Revision Publishing” and replaces “Simple Manual”

2、of NSX-T929 (LH), (S/M Code No. 09-00C-440-2T1). If requiring information about the CD mechanism, see Service Manual of 6ZG-1, (S/M Code No. 09-001-338-7N8). SPEAKER SX-WNT929 REVISION RadioFans.CN 收音机爱 好者资料库 2 SPECIFICATIONS Tuning range87.5 MHz to 108 MHz Usable sensitivity (IHF)13.2 dBf Antenna t

3、erminals75 ohms (unbalanced) Tuning range531 kHz to 1602 kHz (9 kHz step) 530 kHz to 1710 kHz (10 kHz step) Usable sensitivity350 V/m AntennaLoop antenna Power outputRated: 250 W + 250 W (8 ohms, T.H.D. 1 %, 60Hz ) Reference: 320 W + 320 W (8 ohms, T.H.D. 10 %, 60Hz ) Total harmonic distortion0.3 %

4、(125 W, 60Hz, 8 ohms, DIN AUDIO) InputsVIDEO/AUX: 300 mV (adjustable) MD: 300 mV (adjustable) MIC 1, MIC 2: 1.0 mV (10 kohms) OutputsLINE OUT: 210 mV SPEAKERS: accept speakers of 8 ohms or more SURROUND SPEAKERS: accept speakers of 8 ohms to 16 ohms PHONES (stereo jack): accepts headphones of 32 ohm

5、s or more Track format4 tracks, 2 channels stereo Frequency responseCrO2 tape: 50 Hz 16000 Hz Normal tape: 50 Hz 15000 Hz Signal-to-noise ratio60 dB (Dolby B NR ON, CrO2 tape peak level) Recording systemAC bias HeadsDeck 1: Playback head x 1 Deck 2: Recording/playback head x 1, erase head x 1 LaserS

6、emiconductor laser ( =780 nm) D-A converter1 bit dual Signal-to-noise ratio85 dB (1 kHz, 0 dB) Harmonic distortion0.05 % (1 kHz, 0 dB) Power requirements120 V/ 220V230V/ 240 V AC (switchable) 50/60 Hz Power consumption390 W Power consumption inWith ECO mode on: 0.9 W standby modeWith ECO mode off: 4

7、7 W Dimensions (W x H x D)300 x 383.5 x 404.5 mm Weight of main unit17.2 kg Speaker system3 way,built-in subwoofer (magnetic shielded type) Speaker unitsWoofer: 160 mm X 2 cone Mid range: 140 mm cone Super tweeter: 20 mm ceramic Impedance8 ohms / 8 ohms Dimensions (W x H x D)270 x 495 x 297 mm Weigh

8、t6.5 kg Manufactured under license from Dolby Laboratories Licensing Corporation. “DOLBY” and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation. The word “BBE” and the “BBE symbol” are trademarks of BBE Sound, Inc. Under license from BBE Sound, Inc. Design and specificat

9、ions are subject to change without notice. RadioFans.CN 收音机爱 好者资料库 3 CLASS 1LASER PRODUCT KLASSE 1LASER PRODUKT LUOKAN 1LASER LAITE KLASS 1LASER APPARAT This set employs laser. Therefore, be sure to follow carefully the instructions below when servicing. WARNING! WHEN SERVICING, DO NOT APPROACH THE

10、LASER EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE FROM A DISTANCE OF MORE THAN 30cm FROM THE SURFACE OF THE OBJEC- TIVE LENS ON THE OPTICAL PICK-UP BLOCK. sCaution: Invisible laser radiation when open and interlocks defeated avoid exposur

11、e to beam. sAdvarsel: Usynlig laserstling ved bning, nr sikkerhedsafbrydere er ude af funktion. Undg udsttelse for strling. VAROITUS! Laiteen Kyttminen muulla kuin tss kyttohjeessa mainitulla tavalla saataa altistaa kyt-tjn turvallisuusluokan 1 ylittvlle nkymttmlle lasersteilylle. VARNING! Om appara

12、ten anvnds p annat stt n vad som specificeras i denna bruksanvising, kan anvndaren utsttas fr osynling laserstrlning, som verskrider grnsen fr laserklass 1. PROTECTION OF EYES FROM LASER BEAM DURING SERVICING CAUTION Use of controls or adjustments or performance of proce- dures other than those spec

13、ified herin may result in hazardous radiation exposure. ATTENTION Lutillisation de commandes, rglages ou procdures autres que ceux spcifis peut entraner une dangereuse exposition aux radiations. ADVARSEL Usynlig laserstling ved bning, nr sikkerhedsafbrydereer ude af funktion. Undg udsttelse for strl

14、ing. This Compact Disc player is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label is located on the rear exterior. Precaution to replace Optical block (KSS-213F) Body or clothes electrostatic potential could ruin laser diode in the optical block. Be sure ground body and workben

15、ch, and use care the clothes do not touch the diode. 1) After the connection, remove solder shown in right figure. PICK-UP Assy PWB Solder RadioFans.CN 收音机爱 好者资料库 4 NOTE ON BEFORE STARTING REPAIR Charging voltage (V)Discharging Rated power (W)Parts number (C101, 102)resistor () 25-48100387-A00-247-0

16、90 49-140220587-A00-232-090 Note: The reference numbers (C101, C102) of the electrolytic capacitors can change depending on the models. Be sure to check the reference numbers of the charging capacitors on schematic diagram before starting the discharging work. 2. Check items before exchanging the MI

17、CROCOMPUTER Be sure to check the following items before exchanging the MICROCOMPUTER. Exchange the MICROCOMPUTER after confirming that the MICROCOMPUTER is surely defective. 2-1. Regarding the HOLD terminal of the MICROCOMPUTER When the HOLD terminal (INPUT) of the MICROCOMPUTER is “H”, the MICROCOM

18、PUTER is judged to be operating correctly. When this terminal is “L”, the main power cannot be turned on. Therefore, be sure to check the terminal voltage of the HOLD terminal before exchange. When the MICROCOMPUTER is not defective, the HOLD terminal can also go “L” when the POWER AMPLIFIER has any

19、 abnormalities that triggers the abnormality detection circuit on the MAIN C. B. that sets the HOLD terminal to “L”. Good or no good judgement of the MICROCOMPUTER 11111Turn on the AC main power. 22222Confirm that the main power is turned on and the HOLD terminal of the MICROCOMPUTER keeps the “H” l

20、evel or not. 33333When the HOLD terminal is “L” level, the abnormality detection circuit is judged to be working correctly and the MICROCOMPUTER is judged to be good. 1. Forced discharge of electrolytic capacitor of power supply block When repair is going to be attempted in the set that uses relay c

21、ircuit in the power supply block, electric potential is kept charged across the electrolytic capacitors (C101, 102) even though AC power cord is removed. If repair is attempted in this condition, secondary defect can occur. In order to prevent the secondary trouble, perform the following measures be

22、fore starting repair work. Discharge procedure 11111Remove the AC power cord. 22222Connect a discharging resistor at an end of lead wire that has clips at both ends. Connect the other end of the lead wire to metal chassis. 33333Contact the other end of the discharging resistor to the positive (+) si

23、de (+VH) of C101. (For two seconds) 44444Contact the same end of the discharging resistor as step 33333 to the negative (-) side (-VH) of C102 in the same way. (For two seconds) 55555Check that voltage across C101 and C102 has decreased to 1 V or less using a multimeter or an oscilloscope. Select a

24、discharging resistor referring to the following table.Fig-1 MAIN C.B D101 C101C102 22 34 5 In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not. 2-2. Regarding reset There are cases that the machine does not work correctly because the MICROCO

25、MPUTER is not reset even though the AC power cord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed. When the above described phenomenon occurs, it can lead to wrong judgement as if the MICROCOMPUTER is defective and to exchange the MICROCOMPUTER. In such a case,

26、 perform the forced-reset by the following procedure and check good or no good of the MICROCOMPUTER. 11111Remove the AC power cord. 22222Short both ends of the electrolytic capacitor C113 that is connected to VDD of the MICROCOMPUTER with tweezers. 33333Connect the AC power cord again. If the MICROC

27、OMPUTER returns to the normal operation, the MICROCOMPUTER is good. Note: The reference number or MICROCOMPUTER pin number of transistor (Q110) and electrolytic capacitor (C113) can change depending on the models. Be sure to check the reference numbers on schematic diagram before starting the discha

28、rging work. 2-3. Confirmation of soldering state of MICROCOMPUTER Check the soldering state of the MICROCOMPUTER in addition to the above described procedures. Be sure to exchange the MICROCOMPUTER after surely confirming that the trouble is not caused by poor soldering but the MICROCOMPUTER itself.

29、 Fig-2-2 MICRO- COMPUTER MICROCOMPUTER FRONT C.B FRONT C.B VSS VDD C113 * % C113 18 15 Short with tweezers. 6 ELECTRICAL MAIN PARTS LIST DESCRIPTIONREF. NO.KANRI NO. PART NO.DESCRIPTIONREF. NO.KANRI NO. PART NO. IC 87-A21-419-040 C-IC,NJM14558MD-TE2 8B-NF4-635-010 C-IC,LC876596W-5T96 87-A21-831-010

30、IC,SPS-422-1-F1 87-A20-355-010 IC,CXA1553P 87-A20-783-040 C-IC,BA7762AFS 87-A21-021-040 C-IC,BU2099FV 87-070-289-040 IC,BU2092F 87-A21-018-040 C-IC,M65849BFP631D 87-A21-452-130 C-IC,BD3876AKS2 87-A21-051-040 C-IC,BU9990-03FS 87-A21-695-010 IC,LA1845L 87-A21-577-040 C-IC,M61506FP 87-A21-928-010 IC,LC

31、72131D-N 87-A21-269-010 IC,EW732 TRANSISTOR 89-213-702-010 TR,2SB1370 (1.8W) 87-A30-087-080 C-FET,2SK2158 87-A30-455-040 C-TR,DTA144EKA 87-A30-515-080 TR,2SA1979O/Y 87-A30-075-080 C-TR,2SA1235F 87-A30-076-080 C-TR,2SC3052F 87-A30-086-070 C-TR,CSD1306E 89-213-750-010 TR,2SB1375 (25W) 89-110-372-080 C

32、-TR,2SA1037K(R) 87-026-610-080 TR,KTC3198GR 87-A30-495-080 TR,2SA1981Y 87-A30-107-070 C-TR,CMBT5401 87-A30-106-040 C-TR,CMBT5551 87-A30-190-080 TR,CC5551 87-A30-523-010 TR,2SD2562 87-A30-522-010 TR,2SB1649 87-A30-218-080 TR,2SB1237(Q) 87-026-609-080 TR,KTA1266GR 87-A30-447-040 C-TR,DTA114EKA 87-A30-

33、427-040 C-TR,DTC114EKA 87-A30-097-010 TR,FN1016 87-A30-098-010 TR,FP1016 87-A30-276-040 C-TR,DTA143EKA 87-A30-186-010 FET,2SK3053 87-A30-582-080 TR,CDA1585BC 87-A30-318-080 TR,CSA952K 89-327-143-010 C-TR,2SC2714(0) 87-A30-489-080 C-TR,KRA107S 89-503-602-080 C-FET,2SK360E 87-A30-234-080 TR,CSC4115BC

34、87-026-463-080 TR,2SA933S (0.3W) DIODE 87-020-465-080 DIODE,1SS133 (110MA) 87-A40-224-010 DIODE,GBU8DL 87-A40-673-090 DIODE,D10XB20 87-A40-269-080 C-DIODE,MC2836 87-A40-270-080 C-DIODE,MC2838 87-A40-784-080 ZENER,UZ39BSB 87-A40-764-080 ZENER,UZ10BSC 87-A40-553-080 DIODE,1N4003 LES 87-A40-488-080 DIO

35、DE,1SS244 87-A40-234-080 ZENER,MTZJ5.6A 87-A40-747-080 ZENER,UZ5.1BSB 87-A40-646-010 DIODE,FMB-G16L 87-A40-313-080 C-DIODE,MC2840 87-A40-751-080 ZENER,UZ6.2BSB 87-A40-745-080 ZENER,UZ4.7BSA 87-A40-392-080 DIODE,1N5818-T 87-A40-749-080 ZENER,UZ5.6BSB 87-017-149-080 ZENER,HZS6A2L MAIN C.B C11 87-A12-3

36、17-080 C-CAP,U 0.1-50 Z F C12 87-A12-317-080 C-CAP,U 0.1-50 Z F C13 87-A12-317-080 C-CAP,U 0.1-50 Z F C14 87-A12-317-080 C-CAP,U 0.1-50 Z F C15 87-A10-122-090 CAP,E 6800-65 VR C16 87-A10-122-090 CAP,E 6800-65 VR C19 87-016-035-090 CAP, E 6800-35 VR C20 87-016-035-090 CAP, E 6800-35 VR C31 87-A12-062

37、-080 CAP,E 100-10 SMG C32 87-012-286-080 C-CAP,U 0.01-25 K B C33 87-A12-071-080 CAP,E 47-25 SMG C34 87-A12-089-080 CAP,E 3.3-50 SMG C35 87-012-286-080 C-CAP,U 0.01-25 KB C36 87-A12-062-080 CAP,E 100-10 SMG C37 87-A12-072-080 CAP,E 100-25 SMG C38 87-A12-092-080 CAP,E 22-50 SMG C39 87-A12-066-080 CAP,

38、E 47-16 SMG C40 87-A12-074-080 CAP,E 470-25 SMG C113 87-012-195-080 C-CAP,U 100P-50CH C114 87-012-195-080 C-CAP,U 100P-50CH C117 87-A12-317-080 C-CAP,U 0.1-50 Z F C118 87-A12-317-080 C-CAP,U 0.1-50 Z F C127 87-A12-317-080 C-CAP,U 0.1-50 Z F C131 87-A12-087-080 CAP,E 1-50 SMG C132 87-A12-061-080 CAP,

39、E 47-10 SMG C133 87-A12-071-080 CAP,E 47-25 SMG C301 87-012-188-080 C-CAP,U 47P-50 CH C302 87-012-188-080 C-CAP,U 47P-50 CH C303 87-012-336-080 C-CAP,U 330P-50 J SL C304 87-012-336-080 C-CAP,U 330P-50 J SL C305 87-012-336-080 C-CAP,U 330P-50 J SL C306 87-012-336-080 C-CAP,U 330P-50 J SL C307 87-010-

40、759-080 C-CAP,U 0.1-25F C311 87-010-787-080 CAP, U 0.022-25 K B C312 87-010-787-080 CAP, U 0.022-25 K B C313 87-012-276-080 C-CAP,U 1500P-50 B C314 87-012-276-080 C-CAP,U 1500P-50 B C315 87-012-274-080 CHIP CAP,U 1000P-50B C316 87-012-274-080 CHIP CAP,U 1000P-50B C317 87-A10-706-080 C-CAP,U 0.33U-16

41、 F Z C318 87-A10-706-080 C-CAP,U 0.33U-16 F Z C319 87-A10-025-080 C-CAP,U 0.22-16Z F C320 87-A10-025-080 C-CAP,U 0.22-16Z F C321 87-A10-025-080 C-CAP,U 0.22-16Z F C322 87-A10-025-080 C-CAP,U 0.22-16Z F C324 87-A12-071-080 CAP,E 47-25 SMG C325 87-A12-057-080 CAP,E 330-6.3 SMG C327 87-A12-090-080 CAP,

42、E 4.7-50 SMG C328 87-A12-090-080 CAP,E 4.7-50 SMG C332 87-010-759-080 C-CAP,U, 0.1-25F C335 87-A12-087-080 CAP,E 1-50 SMG C336 87-A12-087-080 CAP,E 1-50 SMG C337 87-010-759-080 C-CAP,U 0.1-25F C339 87-010-759-080 C-CAP,U 0.1-25F C340 87-010-759-080 C-CAP,U 0.1-25F C351 87-A10-039-080 C-CAP,U 470P-50

43、 J CH C352 87-A10-039-080 C-CAP,U 470P-50 J CH C354 87-010-175-080 C-CAP,S 560P-50 J SL C355 87-012-274-080 CHIP CAP,U 1000P-50B C356 87-A12-071-080 CAP,E 47-25 SMG C357 87-012-286-080 CAP, U 0.01-25 C358 87-012-279-080 C-CAP,U 2700P-50 B C359 87-012-279-080 C-CAP,U 2700P-50 B C360 87-012-279-080 C-

44、CAP,U 2700P-50 B C363 87-A12-361-080 CAP,M 5600P-100 J CP C370 87-010-759-080 C-CAP,U, 0.1-25F C371 87-012-271-080 C-CAP, U 560P-50 C372 87-012-271-080 C-CAP, U 560P-50 C373 87-012-275-080 C-CAP,U 1200P-50 B 7 DESCRIPTIONREF. NO.KANRI NO. PART NO.DESCRIPTIONREF. NO.KANRI NO. PART NO. C374 87-012-275

45、-080 C-CAP,U 1200P-50 B C375 87-A12-084-080 CAP,E 0.22-50 SMG C376 87-A12-084-080 CAP,E 0.22-50 SMG C378 87-010-759-080 C-CAP,U 0.1-25F C381 87-012-286-080 CAP, U 0.01-25 C382 87-012-188-080 C-CAP,U 47P-50 CH C383 87-012-286-080 CAP, U 0.01-25 C384 87-A12-088-080 CAP,E 2.2-50 SMG C385 87-012-280-080

46、 CAP, U 3300P-50 C386 87-010-759-080 C-CAP,U 0.1-25F C388 87-012-199-080 C-CAP,U 220P-50 J CH C501 87-A12-062-080 CAP,E 100-10 SMG C502 87-010-759-080 C-CAP,U 0.1-25F C503 87-A10-353-080 C-CAP,U 0.22-10KB C504 87-A10-353-080 C-CAP,U 0.22-10KB C505 87-A10-025-080 C-CAP,U 0.22-16Z F C506 87-012-280-08

47、0 CAP, U 3300P-50 C507 87-010-986-080 C-CAP,S 820P-25 J CH C508 87-A12-319-080 C-CAP,U 0.1-25 K B C509 87-A12-319-080 C-CAP,U 0.1-25 K B C510 87-012-280-080 CAP, U 3300P-50 C511 87-010-986-080 C-CAP,S 820P-25 J CH C512 87-A10-025-080 C-CAP,U 0.22-16Z F C513 87-A12-083-080 CAP,E 0.1-50 SMG C514 87-A12-061-080 CAP,E 47-10 SMG C515 87-A12-087-080 CAP,E 1-50 SMG C516 87-A12-087-080 CAP,E 1-50 SMG C517 87-012-279-080 C-CAP,U 2700P-50 B C518 87-012-279-080 C-CAP,U 2