Aiwa-XRHG5MD-cs-sm 电路图 维修手册.pdf

《Aiwa-XRHG5MD-cs-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Aiwa-XRHG5MD-cs-sm 电路图 维修手册.pdf（40页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL DATA MD / CD STEREO SYSTEM BASIC TAPE MECHANISM : 2ZM-3MK2 PR4NM BASIC CD MECHANISM : AZG-1 ZD8RMDM BASIC MD MECHANISM : AZG-7 DM XR-HG5MDK, EZ S/M Code No. 09-004-423-9R2 REVISION This Service Manual is the Revision Publishing and replaces Simple Manual XR-HG5MD (K, EZ), (S/M Code No

2、. 09-002-423-9T2). If requiring information about the CD mechanism, see Service Manual of AZG-1 ZD8RMDM, (S/M Code No. 09-001-335-3NA). If requiring information about the MD mechanism, see Service Manual of AZG-7 DM, (S/M Code No. 09-001-338-4N2). XRHG5MD SPEAKERSYSTEM CD CASSEIVER SXWNHG5CXNHG5MD R

3、CZAS16 REMOTE CONTROLLER RadioFans.CN 收音机爱 好者资料库 2 SPECIFICATIONS Tuning range87.5 MHz to 108 MHz Usable sensitivity (IHF)16.8 dBf Antenna terminals75 ohms (unbalanced) Tuning range530 kHz to 1710 kHz (10 kHz step) 531 kHz to 1602 kHz (9 kHz step) Usable sensitivity350 V/m AntennaLoop antenna Tuning

4、 range144 kHz to 290 kHz Usable sensitivity1400 V/m AntennaLoop antenna Mid-high frequency amplifier Power output*Rated: 15 W + 15 W (8 ohms, T.H.D. 1 %, 200 Hz to 20 kHz/ DIN 45500) Reference: 18 W + 18 W (8 ohms, T.H.D. 10 %, 200 Hz to 20 kHz /DIN 45324) EZ: DIN MUSIC POWER: 32 W + 32 W Total harm

5、onic distortion0.06 % (8 W, 1 kHz, 8 ohms, DIN AUDIO) Low frequency amplifier Power output*Rated: 45 W + 45 W (6 ohms, T.H.D. 1 %, 50 Hz to 200 Hz/ DIN 45500) Reference : 54 W + 54 W (6 ohms, T.H.D. 10 %, 50 Hz to 200 HZ/ DIN 45324) EZ: DIN MUSIC POWER: 74 W + 74 W Total harmonic distortion0.06 % (2

6、0 W, 130 Hz, 6 ohms, DIN AUDIO) * without connecting to the SURROUND SPEAKERS InputsVIDEO/AUX: 500 mV DIGITAL IN OutputsSPEAKERS HIGH FREQ: accept speakers of 8 ohms or more SPEAKERS LOW FREQ: accept speakers of 6 ohms or more SURROUND SPEAKERS: accept speakers of 8 to 16 ohms PHONES (stereo jack):

7、accepts headphones of 32 ohms or more CD DIGITAL OUT (OPTICAL) jack Track format4 tracks, 2 channels stereo Frequency response50 Hz 15000 Hz Recording systemAC bias HeadsDeck 1 : Playback head x 1 Deck 2 : Recording/Playback head x 1, erase head x 1 LaserSemiconductor laser ( =780 nm) D-A converter1

8、 bit dual Signal-to-noise ratio85 dB (1 kHz, 0 dB) Harmonic distortion0.05 % (1 kHz, 0 dB) Wow and flutterUnmeasurable Scanning methodNon-contact optical scanner (Semiconductor laser application) Recording sectionMagnetic polarity modulation overwrite system Rotation speedApprox. 400 - 900 rpm (CLV)

9、 Sampling frequency44.1 kHz No. of channelsStereo: 2 channels Monaural: 1 channels A-D, D-A converter1 bit Frequency20 to 20000 Hz +0.5 - 1.5dB Wow and flutterUnmeasurable Cabinet type3 way, built-in subwoofer (magnetic shielded type) SpeakersSubwoofer: 160 mm cone type Full range: 100 mm cone type

10、Super tweeter: 20 mm ceramic type ImpedanceLOW FREQ.: 6 ohms HIGH FREQ.: 8 ohms Output sound pressure level 87 dB/W/m Dimensions (W x H x D)240 x 324 x 270 mm Weight4.8 kg Power requirements230 V AC, 50 Hz Power consumptionEZ: 150 W K: 160 W Power consumption in standby mode If the power-economizing

11、 mode is ECO OFF: 21 W If the power-economizing mode is ECO ON or ECO AUTO: 0.9 W Dimensions of main unit260 x 326.5 x 348 mm (W x H x D) Weight of main unit8.4 kg Design and specifications are subject to change without notice. RadioFans.CN 收音机爱 好者资料库 3 CLASS 1LASER PRODUCT KLASSE 1LASER PRODUKT LUO

12、KAN 1LASER LAITE KLASS 1LASER APPARAT This set employs laser. Therefore, be sure to follow carefully the instructions below when servicing. WARNING! WHEN SERVICING, DO NOT APPROACH THE LASER EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE FRO

13、M A DISTANCE OF MORE THAN 30cm FROM THE SURFACE OF THE OBJEC- TIVE LENS ON THE OPTICAL PICK-UP BLOCK. sCaution: Invisible laser radiation when open and interlocks defeated avoid exposure to beam. sAdvarsel: Usynlig laserstling ved bning, nr sikkerhedsafbrydere er ude af funktion. Undg udsttelse for

14、strling. VAROITUS! Laiteen Kyttminen muulla kuin tss kyttohjeessa mainitulla tavalla saataa altistaa kyt-tjn turvallisuusluokan 1 ylittvlle nkymttmlle lasersteilylle. VARNING! Om apparaten anvnds p annat stt n vad som specificeras i denna bruksanvising, kan anvndaren utsttas fr osynling laserstrlnin

15、g, som verskrider grnsen fr laserklass 1. PROTECTION OF EYES FROM LASER BEAM DURING SERVICING CAUTION Use of controls or adjustments or performance of proce- dures other than those specified herin may result in hazardous radiation exposure. ATTENTION Lutillisation de commandes, rglages ou procdures

16、autres que ceux spcifis peut entraner une dangereuse exposition aux radiations. ADVARSEL Usynlig laserstling ved bning, nr sikkerhedsafbrydereer ude af funktion. Undg udsttelse for strling. This Compact Disc player is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label is located

17、on the rear exterior. Precaution to replace Optical block (KMS-260B / KSM-880CAB) Body or clothes electrostatic potential could ruin laser diode in the optical block. Be sure ground body and workbench, and use care the clothes do not touch the diode. 1) After the connection, remove solder shown in r

18、ight figure. MD PICK-UP Assy P.C.B (KMS-260B) 1 VEE 21 TRK Solder Pattern side solder CD PICK-UP Assy P.C.B (KSM-880CAB) RadioFans.CN 收音机爱 好者资料库 4 NOTE ON BEFORE STARTING REPAIR Charging voltage (V)Discharging Rated power (W)Parts number (C101, 102)resistor () 25-48100387-A00-247-090 49-140220587-A0

19、0-232-090 Note: The reference numbers (C101, C102) of the electrolytic capacitors can change depending on the models. Be sure to check the reference numbers of the charging capacitors on schematic diagram before starting the discharging work. 2. Check items before exchanging the MICROCOMPUTER Be sur

20、e to check the following items before exchanging the MICROCOMPUTER. Exchange the MICROCOMPUTER after confirming that the MICROCOMPUTER is surely defective. 2-1. Regarding the HOLD terminal of the MICROCOMPUTER When the HOLD terminal (INPUT) of the MICROCOMPUTER is “H”, the MICROCOMPUTER is judged to

21、 be operating correctly. When this terminal is “L”, the main power cannot be turned on. Therefore, be sure to check the terminal voltage of the HOLD terminal before exchange. When the MICROCOMPUTER is not defective, the HOLD terminal can also go “L” when the POWER AMPLIFIER has any abnormalities tha

22、t triggers the abnormality detection circuit on the MAIN C. B. that sets the HOLD terminal to “L”. Good or no good judgement of the MICROCOMPUTER 11111Turn on the AC main power. 22222Confirm that the main power is turned on and the HOLD terminal of the MICROCOMPUTER keeps the “H” level or not. 33333

23、When the HOLD terminal is “L” level, the abnormality detection circuit is judged to be working correctly and the MICROCOMPUTER is judged to be good. 1. Forced discharge of electrolytic capacitor of power supply block When repair is going to be attempted in the set that uses relay circuit in the powe

24、r supply block, electric potential is kept charged across the electrolytic capacitors (C101, 102) even though AC power cord is removed. If repair is attempted in this condition, secondary defect can occur. In order to prevent the secondary trouble, perform the following measures before starting repa

25、ir work. Discharge procedure 11111Remove the AC power cord. 22222Connect a discharging resistor at an end of lead wire that has clips at both ends. Connect the other end of the lead wire to metal chassis. 33333Contact the other end of the discharging resistor to the positive (+) side (+VH) of C101.

26、(For two seconds) 44444Contact the same end of the discharging resistor as step 33333 to the negative (-) side (-VH) of C102 in the same way. (For two seconds) 55555Check that voltage across C101 and C102 has decreased to 1 V or less using a multimeter or an oscilloscope. Select a discharging resist

27、or referring to the following table.Fig-1 MAIN C.B D101 C101C102 22 34 5 In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not. 2-2. Regarding reset There are cases that the machine does not work correctly because the MICROCOMPUTER is not rese

28、t even though the AC power cord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed. When the above described phenomenon occurs, it can lead to wrong judgement as if the MICROCOMPUTER is defective and to exchange the MICROCOMPUTER. In such a case, perform the force

29、d-reset by the following procedure and check good or no good of the MICROCOMPUTER. 11111Remove the AC power cord. 22222Short both ends of the electrolytic capacitor C113 that is connected to VDD of the MICROCOMPUTER with tweezers. 33333Connect the AC power cord again. If the MICROCOMPUTER returns to

30、 the normal operation, the MICROCOMPUTER is good. Note: The reference number or MICROCOMPUTER pin number of transistor (Q110) and electrolytic capacitor (C113) can change depending on the models. Be sure to check the reference numbers on schematic diagram before starting the discharging work. 2-3. C

31、onfirmation of soldering state of MICROCOMPUTER Check the soldering state of the MICROCOMPUTER in addition to the above described procedures. Be sure to exchange the MICROCOMPUTER after surely confirming that the trouble is not caused by poor soldering but the MICROCOMPUTER itself. Fig-2-2 MICRO- CO

32、MPUTER MICROCOMPUTER FRONT C.B FRONT C.B VSS VDD C113 * % C113 18 15 Short with tweezers. 6 CAUTIONS WHEN ASSEMBLY 1.Assembling the CAM, LOAD Move the LEVER ASSY, CAM in the direction of the arrow as far as it can go. Rotate the CAM, LOAD so that its positioning hole is moved as close as possible to

33、 the shaft of the LEVER, SW H. Attach the CAM, LOAD so that it engages with the teeth of the GEAR, IDLER2. 2.Assembling the PLATE ASSY, SLIDE L Align the shaft of the PLATE ASSY, SLIDE L with the arrow-marked position of the CAM, LOAD. CAM, LOAD positioning hole Shaft of LEVER, SW H CAM, LOAD LEVER

34、ASSY, CAM CAM, LOAD 7 1.Remove the four screws (BVT2+3-10 W/O SLOT) of A. Remove AZG-4 in the direction of the arrow. DISASSEMBLY INSTRUCTIONS AAAA 2.Remove the four screws (VTT+3-4) of B. Set the mechanism in the PLAY state. Remove the HLDR, SHIELD TOP in the direction of the arrow. HLDR, SHIELD TO

35、P BB B B CCDD MD MECHANISM HLDR, SHIELD BOT FFC A B B HEAD, OWH PLATE, SLIDE R PLATE ASSY, SLIDE L BOSS ZZG-D (b) (a) (c) CAM, LOAD 3.Remove the two screws (S-SCREW, MD TF) of C. Remove the two screws (S-SCREW MD T) of D. Remove the four FFCs and remove the MD MECHANISM. 4.Remove the screw (VW+1.7-5

36、) of A. Remove the HEAD, OWH. Remove the two screws (VTT+2-3) of B. Remove the PLATE ASSY, SLIDE L and the PLATE, SLIDE R. in the direction of the arrow. 5.Move the ZZG-D in the direction of arrow (a). While pushing the BOSS in the direction of arrow (b), remove it in the direction of arrow (c). 6.R

37、emove the CAM, LOAD in the direction of the arrow. Disassembly Procedure 8 ELECTRICAL MAIN PARTS LIST DESCRIPTIONREF. NO.KANRI NO. PART NO.DESCRIPTIONREF. NO.KANRI NO. PART NO. IC 8A-DB8-616-010 C-IC,LC876580W-5N90 87-A21-482-010 IC,RPM6938-H 87-017-888-080 IC,NJM4558MD 87-A21-021-040 C-IC,BU2099FV

38、87-070-289-040 IC,BU 2092F 87-A21-031-040 C-IC,BU4551BF 87-A21-416-040 C-IC,M61500FP 87-A21-023-040 C-IC,BA3835F 87-070-127-110 IC,LC72131 D 87-A20-440-040 C-IC,BU1920FS 87-A20-913-010 IC,LA1837NL 87-020-454-010 IC,DN 6851 87-A21-419-040 C-IC,NJM14558MD-TE2 TRANSISTOR 87-026-245-080 TR,DTC114ES 87-0

39、26-609-080 TR,KTA1266GR 87-A30-198-080 TR,KTC3199GR 89-213-702-010 TR,2SB1370 (1.8W) 87-026-610-080 TR,KTC3198GR 87-A30-076-080 C-TR,2SC3052F 87-A30-075-080 C-TR,2SA1235F 87-A30-234-080 TR,CSC4115BC 87-A30-073-080 C-TR,RT1N 141C 87-A30-186-010 FET,2SK3053 87-A30-074-080 C-TR,RT1P 141C 87-026-210-080

40、 CHIP-TR,DTC144EK 87-A30-190-080 TR,CC5551 87-A30-137-010 TR,2SD2494 87-A30-138-010 TR,2SB1625 87-A30-106-070 C-TR,CMBT5551 87-A30-107-070 C-TR,CMBT5401 87-A30-087-080 C-FET,2SK2158 87-A30-071-080 C-TR,RT1N 144C 87-A30-256-010 TR,2SD1933 87-A30-255-010 TR,2SB1342 87-A30-329-080 TR,CD1585BC 87-A30-31

41、8-080 TR,CSA952K 87-A30-091-080 FET,2SJ460 87-A30-090-080 FET,2SK2541 87-A30-104-080 C-TR,RT1N 441C 87-A30-085-040 C-TR,CSA1362GR 87-A30-086-070 C-TR,CSD1306E 89-327-143-080 C-TR,2SC2714 (0.1W) 87-A30-072-080 C-TR,RT1P 144C 87-026-463-080 TR,2SA933S 89-503-602-080 C-FET,2SK360E DIODE 87-A40-736-080

42、DIODE,1N4148M(SEM) 87-A40-547-090 DIODE,D5SBA20 87-070-274-080 DIODE,1N4003 SEM 87-A40-777-080 ZENER,UZ30BSB 87-A40-548-090 DIODE,D3SBA20 87-A40-764-080 ZENER,UZ10BSC 87-A40-270-080 C-DIODE,MC2838 87-A40-269-080 C-DIODE,MC2836 87-A40-749-080 ZENER,UZ5.6BSB 87-A40-393-090 DIODE,1N5402GW(F20) 87-A40-7

43、67-080 ZENER,UZ12BSC 87-A40-766-080 ZENER,UZ11BSC 87-A40-752-080 ZENER,UZ6.2BSC 87-A40-739-080 ZENER,UZ2.7BSA 87-A40-802-080 ZENER,UZ5.1BSC 87-017-149-080 ZENER,HZS6A2L 87-A40-335-080 ZENER,MTZJ11C T-72 MAIN C.B C1 87-012-369-080 C-CAP,S 0.047-50F C2 87-012-369-080 C-CAP,S 0.047-50F C3 87-012-368-08

44、0 C-CAP,S 0.1-50 F C4 87-012-368-080 C-CAP,S 0.1-50 F C5 87-012-368-080 C-CAP,S 0.1-50 F C6 87-012-368-080 C-CAP,S 0.1-50 F C9 87-016-658-000 CAP,E 4700-35 M SMG C10 87-A10-520-000 CAP,E 3300-35 M SMG C11 87-012-368-080 C-CAP,S 0.1-50 F C12 87-012-368-080 C-CAP,S 0.1-50 F C13 87-012-368-080 C-CAP,S

45、0.1-50 F C21 87-010-385-080 CAP, ELECT 220-25V C22 87-010-385-080 CAP, ELECT 220-25V C23 87-010-247-080 CAP, ELECT 100-50V C24 87-010-247-080 CAP, ELECT 100-50V C25 87-010-430-080 CAP, ELECT 100-63 C26 87-010-263-080 CAP, ELECT 100-10V C27 87-010-197-080 CAP, CHIP 0.01 DM C29 87-010-247-080 CAP, ELE

46、CT 100-50V C30 87-010-381-080 CAP, ELECT 330-16V C31 87-010-235-080 CAP,E 470-16 SME C32 87-010-405-080 CAP, ELECT 10-50V C33 87-010-405-080 CAP, ELECT 10-50V C34 87-012-368-080 C-CAP,S 0.1-50 F C35 87-010-198-080 CAP, CHIP 0.022 C36 87-010-198-080 CAP, CHIP 0.022 C40 87-010-112-080 CAP, ELECT 100-1

47、6V C50 87-010-182-080 C-CAP,S 2200P-50 B C51 87-010-180-080 C-CER 1500P C61 87-010-260-080 CAP, ELECT 47-25V C62 87-010-403-080 CAP, ELECT 3.3-50V C91 87-010-401-080 CAP, ELECT 1-50V C92 87-010-374-080 CAP, ELECT 47-10V C93 87-010-380-080 CAP, ELECT 47-16V C101 87-010-178-080 CHIP CAP 1000P C102 87-

48、010-178-080 CHIP CAP 1000P C103 87-010-402-080 CAP, ELECT 2.2-50V C104 87-010-402-080 CAP, ELECT 2.2-50V C107 87-010-406-080 CAP, ELECT 22-50V C108 87-010-406-080 CAP, ELECT 22-50V C109 87-010-322-080 C-CAP,S 100P-50 CH C110 87-010-322-080 C-CAP,S 100P-50 CH C111 87-010-260-080 CAP, ELECT 47-25V C112 87-010-260-080 CAP, ELECT 47-25