Aiwa-NSXSZ700-cs-sm 电路图 维修手册.pdf

《Aiwa-NSXSZ700-cs-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Aiwa-NSXSZ700-cs-sm 电路图 维修手册.pdf（38页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL DATA COMPACT DISC STEREO SYSTEM NSX-AJ700 NSX-SZ700 NSX-SZ705 U LH LH S/M Code No. 09-013-441-7R1 REVISION If requiring information about the CD mechanism, see Service Manual of BZG-5, (S/M Code No. 09-00C-353-3N2). This Service Manual is the “Revision Publishing” and replaces “Simple

2、 Manual” NSX-AJ700 (U) / NSX-SZ700 (LH) / NSX-SZ705 (LH), (S/M Code No. 09-012-441-7T1). BASIC TAPE MECHANISM : 2ZM-3MK2 PR9NM ZZM-3 PR1NM BASIC CD MECHANISM : BZG-5 ZD3N1M NSXAJ700 SYSTEM CD CASSEIVER CXNAJ700 NSXSZ700CXNSZ700 NSXSZ705CXNSZ705 TAPE MECHANISM ZZM-3 PR1NM 2ZM-3MK2 PR9NM SPEAKER REMOT

3、E CONTROLLER SXNAJ702 RCBAS02SXWNSZ703 SXNSZ7052ZM-3MK2 PR9NM RadioFans.CN 收音机爱 好者资料库 2 Tuning range87.5 MHz to 108 MHz Usable sensitivity (IHF)13.2 dBf Antenna terminals75 ohms (unbalanced) Tuning range530 kHz to 1710 kHz (10 kHz step) 531 kHz to 1602 kHz (9 kHz step) Usable sensitivity350 V/m Ante

4、nnaLoop antenna Power outputU : 100 W + 100 W (50 Hz to 20 kHz, T.H.D. less than 1 %, 6 ohms) 120 W + 120 W (1 kHz, T.H.D. less than 10 %, 6 ohms) LH : Rated 112 W + 112 W (1 kHz, T.H.D. 1 %, 6 ohms) Reference : 140 W + 140 W (6 ohms, T.H.D. 10 %, 1 kHz) Total harmonic distortionU : 0.08 % (10 W, 1

5、kHz, 6 ohms, DIN AUDIO) LH : 0.08 % (70 W, 1 kHz, 6 ohms, DIN AUDIO) InputsVIDEO / AUX: 700 mV LH only : MIC : 1.7 mV (10 kohms) OutputsSPEAKERS : accept speakers of 6 ohms or more PHONES : accepts headphones of 32 ohms or more LaserSemiconductor laser ( = 780 nm) D/A converter1 bit dual Signal-to-n

6、oise ratio85 dB (1 kHz, 0 dB) Harmonic distortion0.05 % (1 kHz, 0 dB) Track format4 tracks, 2 channels stereo Frequency response50 Hz 15000 Hz Recording systemAC bias HeadsDeck 1 : Playback x 1 Deck 2 : Recording / Playback x 1, erase x 1 Speaker system2 way, bass reflex (magnetic shielded) Speaker

7、unitsWoofer : 160 mm (63/8 in.) cone Tweeter : 60 mm (23/8 in.) cone Impedance6 ohms Dimensions230 x 324 x 253 mm (W x H x D)(91/8 x 127/8 x 10 in.) Weight4.6 kg (10 lbs 2 oz.) SPECIFICATIONS Speaker system3 way, built-in subwoofer (magnetic shielded type) Speaker unitsSubwoofer : 160 mm cone type F

8、ull range : 100 mm cone type Super tweeter : 20 mm ceramic type Impedance6 ohms Dimensions230 x 324 x 257 mm (W x H x D) Weight4.8 kg Speaker system2 way, bass reflex (magnetic shielded) Speaker unitsWoofer : 160 mm cone Tweeter : 60 mm cone Impedance6 ohms Dimensions230 x 324 x 235 mm (W x H x D) W

9、eight4.6 kg Power requirementsU : 120 V AC, 60 Hz LH : 120 V / 220 230 V / 240 V AC, (switchable), 50 / 60 Hz Power consumptionU : 100 W LH : 130 W Power consumptionWith ECO mode on : 0.6 W in standby modeWith ECO mode off : 23 W Dimensions of main unit260 x 326 x 345 mm (W x H x D)(101/4 x 127/8 x

10、135/8 in.) Weight of main unitU : 7.5 kg (16 lbs 9 oz.) LH : 8.4 kg Design and specifications are subject to change without notice. The word BBEand the BBE symbol are trademarks of BBE Sound, Inc. Under license from BBE Sound,Inc. RadioFans.CN 收音机爱 好者资料库 3 CLASS 1LASER PRODUCT KLASSE 1LASER PRODUKT

11、LUOKAN 1LASER LAITE KLASS 1LASER APPARAT This set employs laser. Therefore, be sure to follow carefully the instructions below when servicing. WARNING! WHEN SERVICING, DO NOT APPROACH THE LASER EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE

12、FROM A DISTANCE OF MORE THAN 30cm FROM THE SURFACE OF THE OBJEC- TIVE LENS ON THE OPTICAL PICK-UP BLOCK. sCaution: Invisible laser radiation when open and interlocks defeated avoid exposure to beam. sAdvarsel: Usynlig laserstling ved bning, nr sikkerhedsafbrydere er ude af funktion. Undg udsttelse f

13、or strling. VAROITUS! Laiteen Kyttminen muulla kuin tss kyttohjeessa mainitulla tavalla saataa altistaa kyt-tjn turvallisuusluokan 1 ylittvlle nkymttmlle lasersteilylle. VARNING! Om apparaten anvnds p annat stt n vad som specificeras i denna bruksanvising, kan anvndaren utsttas fr osynling laserstrl

14、ning, som verskrider grnsen fr laserklass 1. PROTECTION OF EYES FROM LASER BEAM DURING SERVICING CAUTION Use of controls or adjustments or performance of proce- dures other than those specified herin may result in hazardous radiation exposure. ATTENTION Lutillisation de commandes, rglages ou procdur

15、es autres que ceux spcifis peut entraner une dangereuse exposition aux radiations. ADVARSEL Usynlig laserstling ved bning, nr sikkerhedsafbrydereer ude af funktion. Undg udsttelse for strling. This Compact Disc player is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label is locat

16、ed on the rear exterior. Precaution to replace Optical block (KSS-213F) Body or clothes electrostatic potential could ruin laser diode in the optical block. Be sure ground body and workbench, and use care the clothes do not touch the diode. 1) After the connection, remove solder shown in right figur

17、e. PICK-UP Assy PWB Solder RadioFans.CN 收音机爱 好者资料库 4 NOTE ON BEFORE STARTING REPAIR Charging voltage (V)Discharging Rated power (W)Parts number (C101, 102)resistor () 25-48100387-A00-247-090 49-140220587-A00-232-090 Note: The reference numbers (C101, C102) of the electrolytic capacitors can change d

18、epending on the models. Be sure to check the reference numbers of the charging capacitors on schematic diagram before starting the discharging work. 2. Check items before exchanging the MICROCOMPUTER Be sure to check the following items before exchanging the MICROCOMPUTER. Exchange the MICROCOMPUTER

19、 after confirming that the MICROCOMPUTER is surely defective. 2-1. Regarding the HOLD terminal of the MICROCOMPUTER When the HOLD terminal (INPUT) of the MICROCOMPUTER is “H”, the MICROCOMPUTER is judged to be operating correctly. When this terminal is “L”, the main power cannot be turned on. Theref

20、ore, be sure to check the terminal voltage of the HOLD terminal before exchange. When the MICROCOMPUTER is not defective, the HOLD terminal can also go “L” when the POWER AMPLIFIER has any abnormalities that triggers the abnormality detection circuit on the MAIN C. B. that sets the HOLD terminal to

21、“L”. Good or no good judgement of the MICROCOMPUTER 11111Turn on the AC main power. 22222Confirm that the main power is turned on and the HOLD terminal of the MICROCOMPUTER keeps the “H” level or not. 33333When the HOLD terminal is “L” level, the abnormality detection circuit is judged to be working

22、 correctly and the MICROCOMPUTER is judged to be good. 1. Forced discharge of electrolytic capacitor of power supply block When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across the electrolytic capacitors (C101, 1

23、02) even though AC power cord is removed. If repair is attempted in this condition, secondary defect can occur. In order to prevent the secondary trouble, perform the following measures before starting repair work. Discharge procedure 11111Remove the AC power cord. 22222Connect a discharging resisto

24、r at an end of lead wire that has clips at both ends. Connect the other end of the lead wire to metal chassis. 33333Contact the other end of the discharging resistor to the positive (+) side (+VH) of C101. (For two seconds) 44444Contact the same end of the discharging resistor as step 33333 to the n

25、egative (-) side (-VH) of C102 in the same way. (For two seconds) 55555Check that voltage across C101 and C102 has decreased to 1 V or less using a multimeter or an oscilloscope. Select a discharging resistor referring to the following table.Fig-1 MAIN C.B D101 C101C102 22 34 5 In such a case, check

26、 also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not. 2-2. Regarding reset There are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC power cord is re-inserted, or the software reset (pressing the STOP key +

27、 POWER key) is performed. When the above described phenomenon occurs, it can lead to wrong judgement as if the MICROCOMPUTER is defective and to exchange the MICROCOMPUTER. In such a case, perform the forced-reset by the following procedure and check good or no good of the MICROCOMPUTER. 11111Remove

28、 the AC power cord. 22222Short both ends of the electrolytic capacitor C113 that is connected to VDD of the MICROCOMPUTER with tweezers. 33333Connect the AC power cord again. If the MICROCOMPUTER returns to the normal operation, the MICROCOMPUTER is good. Note: The reference number or MICROCOMPUTER

29、pin number of transistor (Q110) and electrolytic capacitor (C113) can change depending on the models. Be sure to check the reference numbers on schematic diagram before starting the discharging work. 2-3. Confirmation of soldering state of MICROCOMPUTER Check the soldering state of the MICROCOMPUTER

30、 in addition to the above described procedures. Be sure to exchange the MICROCOMPUTER after surely confirming that the trouble is not caused by poor soldering but the MICROCOMPUTER itself. Fig-2-2 MICRO- COMPUTER MICROCOMPUTER FRONT C.B FRONT C.B VSS VDD C113 * % C113 18 15 Short with tweezers. 6 EL

31、ECTRICAL MAIN PARTS LIST DESCRIPTIONREF. NO.KANRI NO. PART NO.DESCRIPTIONREF. NO.KANRI NO. PART NO. IC 8B-NF7-631-030 C-IC,LC866560W-5V01 87-A21-831-010 IC,SPS-422-1-F1 87-A21-419-040 C-IC,NJM14558MD-TE2 87-A21-893-040 C-IC,NJM14558V-TE2 87-A21-023-040 C-IC,BA3835F 87-A21-401-040 C-IC,M61503FP 87-A2

32、1-695-010 IC,LA1845L 87-070-127-110 IC,LC72131D 87-A21-269-010 IC,EW732 TRANSISTOR 87-A30-494-080 TR,2SA1980G 87-A30-559-010 TR,CSB1370EF 87-A30-492-080 TR,2SC5343G 87-A30-076-080 C-TR,2SC3052F 87-A30-075-080 C-TR,2SA1235F 87-A30-107-070 C-TR,CMBT5401 87-A30-484-080 C-TR,KRA102S 87-A30-190-080 TR,CC

33、5551 87-A30-106-040 C-TR,CMBT5551 87-A30-098-010 TR,FP 1016 87-A30-097-010 TR,FN 1016 87-026-609-080 TR,KTA1266GR 87-A30-087-080 C-FET,2SK2158 87-A30-490-080 C-TR,KRC107S 87-A30-047-080 TR,CSD655E 87-A30-074-080 C-TR,RT1P 141C 87-A30-162-010 FET,2SK2937 87-A30-582-080 TR,CDA1585BC 87-A30-495-080 TR,

34、2SA1981Y 87-A30-091-080 FET,2SJ460 87-A30-090-080 FET,2SK2541 87-A30-062-080 C-TR,KRC104S 89-327-143-080 TR,2SC2714O 87-A30-489-080 C-TR,KRA107S 89-503-602-080 C-FET,2SK360E 87-A30-520-080 TR,2SC5342Y 87-A30-515-080 TR,2SA1979O/Y 87-A30-234-080 TR,CSC4115BC 87-A30-216-080 TR,2SA933AS(R) DIODE 87-A40

35、-393-090 DIODE,1N5402GW(F20) 87-A40-291-080 DIODE,1N4148M(CPT) 87-A40-838-090 DIODE,G3SBA60L-6088 87-A40-839-090 DIODE,G5SBA60L-6088 87-A40-781-080 ZENER,UZ36BSA 87-A40-764-080 ZENER,UZ10BSC 87-A40-553-080 DIODE,1N4003 LES 87-A40-270-080 C-DIODE,MC2838 87-A40-269-080 C-DIODE,MC2836 87-A40-488-080 DI

36、ODE,1SS244 87-A40-748-080 ZENER,UZ5.6BSA 87-A40-747-080 ZENER,UZ5.1BSB 87-A40-749-080 ZENER,UZ5.6BSB 87-A40-802-080 ZENER,UZ5.1BSC 87-A40-739-080 ZENER,UZ2.7BSA 87-017-149-080 ZENER,HZS6A2L MAIN C.B C3 87-A12-317-080 C-CAP,U 0.1-50 Z F C4 87-A12-317-080 C-CAP,U 0.1-50 Z F C5 87-A12-317-080 C-CAP,U 0

37、.1-50 Z F C6 87-A12-317-080 C-CAP,U 0.1-50 Z F C9 87-010-759-080 C-CAP,U, 0.1-25F C10 87-010-759-080 C-CAP,U, 0.1-25F C11 87-010-759-080 C-CAP,U, 0.1-25F C12 87-010-759-080 C-CAP,U, 0.1-25F C19 87-A12-382-000 CAP,E 2200-63 M 85 IV LELON C19 87-A12-383-000 CAP,E 3300-65 M 85 IV LELON C20 87-A12-382-0

38、00 CAP,E 2200-63 M 85 IV LELON C20 87-A12-383-000 CAP,E 3300-65 M 85 IV LELON C21 87-A12-780-090 CAP,E 4700-35 M 85 SKR C22 87-A12-780-090 CAP,E 4700-35 M 85 SKR C31 87-A12-091-080 CAP,E 10-50 SMG C32 87-012-286-080 CAP, U 0.01-25 C33 87-A12-062-080 CAP,E 100-10 SMG C34 87-A12-072-080 CAP,E 100-25 S

39、MG C35 87-A12-071-080 CAP,E 47-25 SMG C36 87-A12-067-080 CAP,E 330-16 SMG C38 87-012-286-080 CAP, U 0.01-25 C60 87-A12-089-080 CAP,E 3.3-50 SMG C61 87-A12-071-080 CAP,E 47-25 SMG C83 87-A12-074-080 CAP,E 470-25 SMG C97 87-010-831-080 C-CAP,U,0.1-16F C101 87-012-279-080 C-CAP,U 2700P-50 B C102 87-012

40、-279-080 C-CAP,U 2700P-50 B C103 87-A12-084-080 CAP,E 0.22-50 SMG C104 87-A12-084-080 CAP,E 0.22-50 SMG C105 87-012-277-080 C-CAP, U 1800P-50 B C106 87-012-277-080 C-CAP, U 1800P-50 B C107 87-A12-089-080 CAP,E 3.3-50 SMG C108 87-A12-089-080 CAP,E 3.3-50 SMG C111 87-A12-077-080 CAP,E 33-35 SMG C112 8

41、7-A12-077-080 CAP,E 33-35 SMG C113 87-A10-596-080 C-CAP,S 100P-100 J CH C114 87-A10-596-080 C-CAP,S 100P-100 J CH C117 87-A12-317-080 C-CAP,U 0.1-50 Z F C118 87-A12-317-080 C-CAP,U 0.1-50 Z F C119 87-012-286-080 CAP, U 0.01-25 C120 87-012-286-080 CAP, U 0.01-25 C123 87-010-177-080 C-CAP,S 820P-50 SL

42、 C124 87-010-177-080 C-CAP,S 820P-50 SL C133 87-012-282-080 CAP, U 4700P-50 C140 87-012-278-080 C-CAP,U 2200P-50 B C186 87-010-759-080 C-CAP,U, 0.1-25F C187 87-010-866-080 CAP, ELECT 10-63 C188 87-010-866-080 CAP, ELECT 10-63 C225 87-A12-317-080 C-CAP,U 0.1-50 Z F C226 87-A12-317-080 C-CAP,U 0.1-50

43、Z F C227 87-A12-317-080 C-CAP,U 0.1-50 Z F C228 87-A12-317-080 C-CAP,U 0.1-50 Z F C241 87-010-831-080 C-CAP,U,0.1-16F C301 87-012-275-080 C-CAP,U 1200P-50 B C301 87-012-274-080 CHIP CAP,U 1000P-50B C302 87-012-275-080 C-CAP,U 1200P-50 B C302 87-012-274-080 CHIP CAP,U 1000P-50B C303 87-012-275-080 C-

44、CAP,U 1200P-50 B C304 87-012-275-080 C-CAP,U 1200P-50 B C307 87-A12-062-080 CAP,E 100-10 SMG C308 87-A12-062-080 CAP,E 100-10 SMG C309 87-012-188-080 C-CAP,U 47P-50 CH C310 87-012-188-080 C-CAP,U 47P-50 CH C313 87-012-284-080 CAP, U 6800P-50 C314 87-012-284-080 CAP, U 6800P-50 C315 87-A12-062-080 CA

45、P,E 100-10 SMG C317 87-A12-085-080 CAP,E 0.33-50 SMG C318 87-A12-085-080 CAP,E 0.33-50 SMG C326 87-010-787-080 CAP, U 0.022-25 C327 87-010-831-080 C-CAP,U,0.1-16F C360 87-A12-087-080 CAP,E 1-50 SMG C399 87-A10-039-080 C-CAP,U 470P-50 J CH C401 87-A12-083-080 CAP,E 0.1-50 SMG C402 87-A12-083-080 CAP,

46、E 0.1-50 SMG C403 87-012-193-080 C-CAP,U 82P-50 CH 7 DESCRIPTIONREF. NO.KANRI NO. PART NO.DESCRIPTIONREF. NO.KANRI NO. PART NO. C404 87-012-193-080 C-CAP,U 82P-50 CH C405 87-012-286-080 CAP, U 0.01-25 C406 87-012-286-080 CAP, U 0.01-25 C407 87-012-286-080 CAP, U 0.01-25 C408 87-012-286-080 CAP, U 0.

47、01-25 C409 87-012-278-080 C-CAP,U 2200P-50 B C410 87-012-278-080 C-CAP,U 2200P-50 B C411 87-A12-091-080 CAP,E 10-50 SMG C412 87-A12-091-080 CAP,E 10-50 SMG C452 87-A12-069-080 CAP,E 22-25 SMG C453 87-012-279-080 C-CAP,U 2700P-50 B C454 87-012-279-080 C-CAP,U 2700P-50 B C455 87-012-279-080 C-CAP,U 2700P-50 B C456 87-012-286-080 CAP, U 0.01-25 C457 87-A12-361-080 CAP,M 5600P-100 J CP C458 87-012-274-080 CHIP CAP,U 1000P-50B C459 87-012-271-080 CAP, U 560P-50 C460 87-010-831-080 C-CAP,U,0.1-16F C461 87-012-158-080 C-CAP,S 390P-5