JVC-MXGA3V-cs-sm 电路图 维修手册.pdf

《JVC-MXGA3V-cs-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《JVC-MXGA3V-cs-sm 电路图 维修手册.pdf（65页珍藏版）》请在收音机爱好者资料库上搜索。

1、MX-GA3V Contents Safety precautions - 1- 2 Important for laser products - 1- 3 Preventing static electricity - 1- 4 Disassembly method - 1- 5 Adjustment method - 1- 18 Flow of functional operation until TOC read - 1- 20 Maintenance of laser pickup - 1- 21 Replacement of laser pickup - 1- 21 Descript

2、ion of major ICs - 1- 22 SP-MXGA3VCA-MXGA3VSP-MXGA3V Area Suffix US . SINGAPORE UX . Saudi Araia COPYRIGHT 2003 VICTOR COMPANY OF JAPAN, LTD. No. MB036 2003/11 MX-GA3V SERVICE MANUAL COMPACT COMPONENT SYSTEM Wiring connection - 1- 29 RadioFans.CN 收音机爱 好者资料库 MX-GA3V 1-2 Warning ! CAUTION Good earth g

3、round Place this probe on each exposed metal part. AC VOLTMETER (Having 1000 ohms/v 1500 10W olts, or more sensitivity) 0.15 F AC TYPE Safety Precautions 1. This design of this product contains special hardware and many circuits and components specially for safety purposes. For continued protection,

4、 no changes should be made to the original design unless authorized in writing by the manufacturer. Replacement parts must be identical to those used in the original circuits. Services should be performed by qualified personnel only. 2. Alterations of the design or circuitry of the product should no

5、t be made. Any design alterations of the product should not be made. Any design alterations or additions will void the manufacturers warranty and will further relieve the manufacture of responsibility for personal injury or property damage resulting therefrom. 3. Many electrical and mechanical parts

6、 in the products have special safety-related characteristics. These characteristics are often not evident from visual inspection nor can the protection afforded by them necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have these

7、special safety characteristics are identified in the Parts List of Service Manual. Electrical components having such features are identified by shading on the schematics and by ( ! ) on the Parts List in the Service Manual. The use of a substitute replacement which does not have the same safety char

8、acteristics as the recommended replacement parts shown in the Parts List of Service Manual may create shock, fire, or other hazards. 4. The leads in the products are routed and dressed with ties, clamps, tubings, barriers and the like to be separated from live parts, high temperature parts, moving p

9、arts and/or sharp edges for the prevention of electric shock and fire hazard. When service is required, the original lead routing and dress should be observed, and it should be confirmed that they have been returned to normal, after re-assembling. 5. Leakage currnet check (Electrical shock hazard te

10、sting) After re-assembling the product, always perform an isolation check on the exposed metal parts of the product (antenna terminals, knobs, metal cabinet, screw heads, headphone jack, control shafts, etc.) to be sure the product is safe to operate without danger of electrical shock. Do not use a

11、line isolation transformer during this check. ? Plug the AC line cord directly into the AC outlet. Using a Leakage Current Tester, measure the leakage current from each exposed metal parts of the cabinet, particularly any exposed metal part having a return path to the chassis, to a known good earth

12、ground. Any leakage current must not exceed 0.5mA AC (r.m.s.) ? Alternate check method Plug the AC line cord directly into the AC outlet. Use an AC voltmeter having, 1,000 ohms per volt or more sensitivity in the following manner. Connect a 1,500 10W resistor paralleled by a 0.15 F AC- type capacito

13、r between an exposed metal part and a known good earth ground. Measure the AC voltage across the resistor with the AC voltmeter. Move the resistor connection to each exposed metal part, particularly any exposed metal part having a return path to the chassis, and meausre the AC voltage across the res

14、istor. Now, reverse the plug in the AC outlet and repeat each measurement. Voltage measured Any must not exceed 0.75 V AC(r.m.s.). This corresponds to 0.5 mA AC(r.m.s.). 1. This equipment has been designed and manufactured to meet international safety standards. 2. It is the legal responsibility of

15、the repairer to ensure that these safety standards are maintained. 3. Repairs must be made in accordance with the relevant safety standards. 4. It is essential that safety critical components are replaced by approved parts. 5. If mains voltage selector is provided, check setting for local voltage. B

16、urrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system. RadioFans.CN 收音机爱 好者资料库 MX-GA3V 1-3 VIDEO OUT 110V 127V 220V 230V -240V WARNING LABEL 1. CLASS 1 LASER PRODUCT 2. CAUTION : Visible and in

17、visible laser radiation when open and interlock failed or defeated. Avoid direct exposure to beam. 3. CAUTION : There are no serviceable parts inside the Laser Unit. Do not disassemble the Laser Unit. Replace the complete Laser Unit if it malfunctions. 4. CAUTION : The compact disc player uses invis

18、ible laser radiation and is equipped with safety switches which prevent emission of radiation when the drawer is open and the safety interlocks have failed or are defeated. It is dangerous to defeat the safety switches. Important for laser products REPRODUCTION AND POSITION OF LABELS 5. CAUTION : If

19、 safety switches malfunction, the laser is able to function. 6. CAUTION : Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. ! CAUTION Please use enough caution not to see the beam directly or touch it in c a s e o

20、f a n a d j u s t m e n t o r operation check. VARNING : Osynlig laserstrlning r denna del r ppnad och sprren r urkopplad. Betrakta ej strlen. VARO : Avattaessa ja suojalukitus ohitettaessa olet alttiina nkymttmlle lasersteilylle. l katso steeseen. ADVARSEL : Usynlig laserstrling ved bning, nr sikke

21、rhedsafbrydere er ude af funktion. Undg udsttelse for strling. ADVARSEL : Usynlig laserstrling ved pning, nr sikkerhetsbryteren er avslott. Unng utsettelse for strling. RadioFans.CN 收音机爱 好者资料库 MX-GA3V 1-4 Preventing static electricity 1. Grounding to prevent damage by static electricity Electrostati

22、c discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs. 2. About the earth processing for the destruction prevention by static electri

23、city In the equipment which uses optical pick-up (laser diode), optical pick-up is destroyed by the static electricity of the work environment. Be careful to use proper grounding in the area where repairs are being performed. 2-1 Ground the workbench Ground the workbench by laying conductive materia

24、l (such as a conductive sheet) or an iron plate over it before placing the traverse unit (optical pickup) on it. 2-2 Ground yourself Use an anti-static wrist strap to release any static electricity built up in your body. 3. Handling the optical pickup 1. In order to maintain quality during transport

25、 and before installation, both sides of the laser diode on the replacement optical pickup are shorted. After replacement, return the shorted parts to their original condition. (Refer to the text.) 2. Do not use a tester to check the condition of the laser diode in the optical pickup. The testers int

26、ernal power source can easily destroy the laser diode. 4. Handling the CD changer unit (optical pickup) 1. Do not subject the CD changer unit (optical pickup) to strong shocks, as it is a sensitive, complex unit. 2. Cut off the shorted part of the flexible cable using nippers, etc. after replacing t

27、he optical pickup. For specific details, refer to the replacement procedure in the text. Remove the anti-static pin when replacing the CD changer unit. Be careful not to take too long a time when attaching it to the connector. 3. Handle the flexible cable carefully as it may break when subjected to

28、strong force. 4. It is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn it. Attention when traverse unit is decomposed * Please refer to “Disassembly method” in the text for pick up and how to detach the CD changer mechanism. 1. Remove the CD changer unit. 2.

29、Disconnect the harness from connector on the CD motor board. 3. Solder is put up before the card wire is removed from connector Cn601on the main board as shown in Fig.1 and Fig.2. (When the wire is removed without putting up solder, the CD pick-up assembly might destroy.) 4. Please remove solder aft

30、er connecting the card wire with CN601 when you install picking up in the substrate. Conductive material (conductive sheet) or iron plate (caption) Anti-static wrist strap Soldering Fig.2 Flexible cable Fig.1 CD changer unit CD changer mechanism assembly MX-GA3V 1-5 Disassembly method Commence disas

31、sembly of the set by removing the main units and then proceed to the components and assemblies inside the units. Replacement of the fuses and the power IC ? Top cover ? CD changer unit ? Front panel assembly ? Chassis unit ? CD changer unit ? Removing the main PCB ? Removing the CD changer mechanism

32、 assembly ? Removing the CD pickup ? Replacing the loading motor and belt of the CD changer tray ? Replacing the CD tray rotor belt of CD changer, and removing the motor ? Front panel assembly ? Removing the cassette deck mechanism ? Removing the earphone jack PCB ? Removing the control/FL PCB ? Rem

33、oving the switch PCB and ACTIVE BASS EX. switch PCB ? Removing the cassette deck main motor, and replacing the main belts ? Removing the leaf switches of the cassette deck mechanism ? Removing the cassette deck heads ? Chassis unit ? Removing the 3-pin regulator ? Removing the power amp and supply P

34、CB and the Power Trans PCB ? Removing the sub power PCB MX-GA3V 1-6 Replacement of the fuses and the power IC ? Replacing the fuses (See Fig.1, Fig.3) ? Prior to performing the following procedure, remove the left side BOARD and remove tuner PCB (Fig.3,BB) 1. Replace the fuses inside. Caution Be sur

35、e to use fuses with the specified ratings. ? Replacing the heat sink cover (See Fig.3) 1. Remove four screws B from the rear panel. 2. Pull the heat sink cover outward. ? Replacing the power IC (See Fig.2) ? Prior to performing the following procedure, remove the top cover. 1. Remove the two screws

36、A from the heat sink between the power IC. 2. Remove the solder fixing the power IC. Fig.3 BB B VIDEO OUT 110V 127V 220V 230V -240V Bottom side Fig.1(A) CN951 Fuse(F952) T1.6AL 250V Fuse(F951) T2AL 250V Fuse(F953) T1.25AL 250V Add Lable T2AL 250V Add Lable T1.25AL 250V Component side Fig.1(B1) Fuse(

37、F953) T1.25AL 250V Add Lable T1.25AL 250V Component side Fig.1(B2) Fuse(F951) T2AL 250V Fuse(F952) T1.6AL 250V WA Fig.2 MX-GA3V 1-7 Fig.5 (A)Fig.5 (B) Left Front panel assembly Right Front panel assembly ? Removing the top cover (See Fig.4 and 5) 1. Remove six screws B that retain the top cover from

38、 the panel rear of the body. 2. Remove eight screws C and D that retain the top cover from the two sides of the body. 3. Remove the top cover from the body by lifting it toward the rear. DD Fig.4 Top coverB VIDEO OUT 2 23 -2 CC MX-GA3V 1-8 ? Removing the CD changer unit (See Fig.6 to 9) ? Prior to p

39、erforming the following procedures, remove the top cover and both sides BOARD. Caution Although the CD mechanism unit can be removed without removing the CD tray panel, it is still recommended to remove it in order to prevent damage. a. From the front panel side of this set, push in the sections mar

40、ked with arrows and pull out the CD tray toward the front. b. Remove the CD tray panel by pushing both of its extremities upward in the direction of the arrows. c. Push the CD tray deep into the set. 1. Disconnect the cord wires from the CD PCB CN704, CN607, CN1101 and disconnect CN1 (shield wire) f

41、rom back panel. 2. From the rear of the set, remove two screws E and two screws G on the front panel left and right side. 3. Handle the CD changer unit rear, take out the unit. Fig.10 CD changer unit Fig.6 CD tray panel Fig.7 CD tray panel Fig.8 Accessory terminal Antenna termianl E F F G MX-GA3V 1-

42、9 Fig.10 H Fig.12 I Power amp and supply PCB Claw c GND lug b ? Removing the front panel assembly (See Fig.10 to 11) ? Prior to performing the following procedures, remove the top cover and both board. ? Also remove the CD changer unit. 1. Disconnect the parallel wire and the cord wire from the conn

43、ectors CN701, CN702, CN703, CN850 on the power amp. and supply PCB. 2. Remove two screws H retaining the front panel assembly onto the bottom of the body. 3. Remove two screws I on the left and right side of the set retaining the panel front from the bottom and then remove then GND lug b that comes

44、from the power amp and supply PCB. 4. Disengage the claws c on both sides of the front panel assembly and then remove the assembly. MX-GA3V 1-10 Fig.14 CD PCB Short round CN601 ? Removing the CD PCB (See Fig.12 to 13) ? Prior to performing the following procedures, remove the top cover and both side

45、s board. ? Also remove the CD changer unit. 1. The two screws E that retain the VCD assembly should be removed. 2. Disconnect the wires from CN602, CN603, CN604 and CN605 on the CD PCB, which is located on the back side of the CD changer unit. 3. The two screws J that retain the CD PCB should be rem

46、oved. 4. Remove the CD PCB by pulling it toward the side where the CN601 is located. 5. Using solder, short the CD pickup to connect to short round. Caution After re-connecting the wires, be sure to remove the shorting solder from the GND connection. 6. Disconnect the card wire from the connector CN

47、601 on the main PCB and then remove the main PCB. Fig.12(A) E Fig.12(B) J CD PCB MX-GA3V 1-11 Fig.14 D Fig.16 K ( Silver color)K ( copper color) K ( Silver color) K ( copper color) CD changer mechanism assembly ? Removing the CD changer mechanism assembly (See Fig.14 to 15) ? Prior to performing the

48、 following procedures, remove the top cover and both sides board. ? Also remove the CD changer unit. 1. Removing screws D from the front chuck base of the CD changer mechanism unit. 2. Turn the CD changer mechanism cover base and remove screws E connecting the unit to the CD changer mechanism assembly. 3. Removing four screws K retaining the CD mechanism holder assembly. Caution When replacing the CD changer mechanism assembly, be sure not to mistake the positions of the silver color and copper color spring. Fig.