JVC-THC9-ddcs-sm 电路图 维修手册.pdf

《JVC-THC9-ddcs-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《JVC-THC9-ddcs-sm 电路图 维修手册.pdf（91页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL COPYRIGHT 2005 Victor Company of Japan, Limited No.MB427 2005/8 DVD DIGITAL CINEMA SYSTEM MB42720058 TH-C9 Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade) TABLE OF CONTENTS 1PRECAUTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 2SPECIFIC SERVICE INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7 3DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8 4ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-38 5TROUBLESHOOTING . . . . . . . . . . . . . . . . .

4、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-43 Area suffix US - Singapore UT - Taiwan UX - Saudi Arabia UG - Turkey,South Africa,Egypt UN - Asean (XV-THC9) (SP-PWC9)(SP-THC9C)(SP-THC9F)(SP-THC9F)(SP-THC9S) RadioFans.CN 收音机爱 好者资料库 1-2 (No.MB427)

5、SPECIFICATION Center unit-XV-THC9 *1: This value is measured at System cord CONNECTOR for reference. *2: Corresponding to Linear PCM, Dolby Digital, and DTS Digital Surround (with sampling frequency -32 kHz, 44.1 kHz, 48 kHz) Subwoofer-SP-PWC9 Audio sectionTotal Harmonic Distortion *10.02% Digital i

6、nput*2DIGITAL IN (DBS): -21 dBm to -15 dBm (OPTICAL): (660 nm 30 nm) Video sectionVideo SystemPAL/NTSC Horizontal Resolution500 lines Signal-to-Noise Ratio64 dB Video output levelComposite: 1.0 V(p-p)/75 S-video-Y: 1.0 V(p-p)/75 S-video-C: For PAL: 0.3 V(p-p)/75 S-video-C: For NTSC: 0.286 V(p-p)/75

7、Component-Y: 1.0 V(p-p)/75 Component-PB/PR: 0.7 V(p-p)/75 Video input sensitivity/Impedance (VCR IN)Composite: 1.0 V(p-p)/75 S-video-Y: 1.0 V(p-p)/75 S-video-C: For PAL: 0.3 V(p-p)/75 S-video-C: For NTSC: 0.286 V(p-p)/75 Tuner sectionTuning RangeFM87.5 MHz to 108.0 MHz AM (Except for Middle East)531

8、 kHz to 1 710 kHz(at 9 kHz channel spacing) 530 kHz to 1 710 kHz(at 10 kHz channel spacing) AM (For Middle East)531 kHz to 1 602 kHz(at 9 kHz channel spacing) 530 kHz to 1 600 kHz(at 10 kHz channel spacing) GeneralPower RequirementsAC 110-240 V , 50/60 Hz Power Consumption19 W (at operation) 1.9 W (

9、in standby mode) Dimensions (W H D)400 mm 85 mm 399 mm Mass4.2 kg Amplifier sectionFront/Center/Surround140 W per channel, RMS at 4 at 1 kHz, with 10% total harmonic distortion. Subwoofer300 W, RMS at 4 at 40 Hz, with 10% total harmonic distortion. Speaker sectionSpeaker unit25 cm Bass-reflex Power

10、Handling Capacity300 W Impedance4 Frequency Range25 Hz to 200 Hz GeneralPower RequirementsAC 110 V/ AC 127 V/AC 220-240 V , 50/60 Hz Power Consumption110 W (at operation) 0 W (in standby mode) Dimensions (W H D)264 mm 481 mm 459 mm Mass17.6 kg RadioFans.CN 收音机爱 好者资料库 (No.MB427)1-3 Satellite Speaker-

11、SP-XTHC9 Designs & specifications are subject to change without notice. Front speakers (SP-THC9F)Speaker unitWoofer10.0 cm 2 Midrange10.0 cm 2 Tweeter4 cm Bass-reflex, Magnetically Shielded Power Handling Capacity140 W Impedance4 Frequency Range60 Hz to 20 kHz Dimensions (W H D)270 mm 1 085.5 mm 310

12、 mm Mass8.8 kg each Center speaker (SP-THC9C)Speaker unitWoofer10.0 cm 2 Tweeter4 cm Bass-reflex, Magnetically Shielded Power Handling Capacity140 W Impedance4 Frequency Range65 Hz to 20 kHz Dimensions (W H D)380 mm 141 mm 168 mm Mass3.4 kg Surround speakers (SP-THC9S)Speaker unit8.0 cm Bass-reflex

13、Power Handling Capacity140 W Impedance4 Frequency Range80 Hz to 20 kHz Dimensions (W H D)111.5 mm 148 mm 106.5 mm Mass0.44 kg each RadioFans.CN 收音机爱 好者资料库 1-4 (No.MB427) SECTION 1 PRECAUTION 1.1Safety Precautions (1) This design of this product contains special hardware and many circuits and compone

14、nts specially for safety purpos- es. For continued protection, no changes should be made to the original design unless authorized in writing by the manufacturer. Replacement parts must be identical to those used in the original circuits. Services should be per- formed by qualified personnel only. (2

15、) Alterations of the design or circuitry of the product should not be made. Any design alterations of the product should not be made. Any design alterations or additions will void the manufacturers warranty and will further relieve the manufacture of responsibility for personal injury or property da

16、mage resulting therefrom. (3) Many electrical and mechanical parts in the products have special safety-related characteristics. These characteris- tics are often not evident from visual inspection nor can the protection afforded by them necessarily be obtained by us- ing replacement components rated

17、 for higher voltage, watt- age, etc. Replacement parts which have these special safety characteristics are identified in the Parts List of Ser- vice Manual. Electrical components having such features are identified by shading on the schematics and by ( ) on the Parts List in the Service Manual. The

18、use of a substitute replacement which does not have the same safety charac- teristics as the recommended replacement parts shown in the Parts List of Service Manual may create shock, fire, or other hazards. (4) The leads in the products are routed and dressed with ties, clamps, tubings, barriers and

19、 the like to be separated from live parts, high temperature parts, moving parts and/or sharp edges for the prevention of electric shock and fire hazard. When service is required, the original lead routing and dress should be observed, and it should be confirmed that they have been returned to normal

20、, after reassem- bling. (5) Leakage shock hazard testing After reassembling the product, always perform an isola- tion check on the exposed metal parts of the product (an- tenna terminals, knobs, metal cabinet, screw heads, headphone jack, control shafts, etc.) to be sure the product is safe to oper

21、ate without danger of electrical shock.Do not use a line isolation transformer during this check. Plug the AC line cord directly into the AC outlet. Using a Leakage Current Tester, measure the leakage current from each exposed metal parts of the cabinet, particular- ly any exposed metal part having

22、a return path to the chassis, to a known good earth ground. Any leakage cur- rent must not exceed 0.5mA AC (r.m.s.). Alternate check method Plug the AC line cord directly into the AC outlet. Use an AC voltmeter having, 1,000 per volt or more sensitivity in the following manner. Connect a 1,500 10W r

23、esistor paralleled by a 0.15F AC-type capacitor between an exposed metal part and a known good earth ground. Measure the AC voltage across the resistor with the AC voltmeter. Move the resistor connection to each exposed metal part, particularly any exposed metal part having a return path to the chas

24、sis, and measure the AC voltage across the resistor. Now, reverse the plug in the AC outlet and repeat each measurement. Voltage measured any must not exceed 0.75 V AC (r.m.s.). This corresponds to 0.5 mA AC (r.m.s.). 1.2Warning (1) This equipment has been designed and manufactured to meet internati

25、onal safety standards. (2) It is the legal responsibility of the repairer to ensure that these safety standards are maintained. (3) Repairs must be made in accordance with the relevant safety standards. (4) It is essential that safety critical components are replaced by approved parts. (5) If mains

26、voltage selector is provided, check setting for local voltage. 1.3Caution Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of pre- forming repair of this system. 1.4Critical parts for safety In regard with component parts a

27、ppearing on the silk-screen printed side (parts side) of the PWB diagrams, the parts that are printed over with black such as the resistor ( ), diode ( ) and ICP ( ) or identified by the mark nearby are critical for safety. When replacing them, be sure to use the parts of the same type and rating as

28、 specified by the manufacturer. (This regulation dose not Except the J and C version) Good earth ground Place this probe on each exposed metal part. AC VOLTMETER (Having 1000 ohms/volts, or more sensitivity) 1500 10W 0.15 F AC TYPE (No.MB427)1-5 1.5Preventing static electricity Electrostatic dischar

29、ge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs. 1.5.1 Grounding to prevent damage by static electricity Static electricity in the work

30、area can destroy the optical pickup (laser diode) in devices such as laser products. Be careful to use proper grounding in the area where repairs are being performed. (1) Ground the workbench Ground the workbench by laying conductive material (such as a conductive sheet) or an iron plate over it bef

31、ore placing the traverse unit (optical pickup) on it. (2) Ground yourself Use an anti-static wrist strap to release any static electricity built up in your body. (3) Handling the optical pickup In order to maintain quality during transport and before installation, both sides of the laser diode on th

32、e replacement optical pickup are shorted. After replacement, return the shorted parts to their original condition. (Refer to the text.) Do not use a tester to check the condition of the laser diode in the optical pickup. The testers internal power source can easily destroy the laser diode. 1.6Handli

33、ng the traverse unit (optical pickup) (1) Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit. (2) Cut off the shorted part of the flexible cable using nippers, etc. after replacing the optical pickup. For specific details, refer to the replacement

34、procedure in the text. Remove the anti-static pin when replacing the traverse unit. Be careful not to take too long a time when attaching it to the connector. (3) Handle the flexible cable carefully as it may break when subjected to strong force. (4) I t is not possible to adjust the semi-fixed resi

35、stor that adjusts the laser power. Do not turn it. 1.7Attention when traverse unit is decomposed *Please refer to Disassembly method in the text for the pickup unit. Apply solder to the short land sections before the flexible wire is disconnected from the connecto on the servo board. (If the flexibl

36、e wire is disconnected without applying solder, the pickup may be destroyed by static electricity.) In the assembly, be sure to remove solder from the short land sections after connecting the flexible wire. 1M Conductive material (conductive sheet) or iron palate (caption) Anti-static wrist strap Ca

37、rd wire DVD pickup DVD changer mechanism assembly Connector Short land section 1-6 (No.MB427) 1.8Important for laser products 1.CLASS 1 LASER PRODUCT 2.DANGER : Invisible laser radiation when open and inter lock failed or defeated. Avoid direct exposure to beam. 3.CAUTION : There are no serviceable

38、parts inside the Laser Unit. Do not disassemble the Laser Unit. Replace the complete Laser Unit if it malfunctions. 4.CAUTION : The CD,MD and DVD player uses invisible laser radiation and is equipped with safety switches which prevent emission of radiation when the drawer is open and the safety inte

39、rlocks have failed or are defeated. It is dangerous to defeat the safety switches. 5.CAUTION : If safety switches malfunction, the laser is able to function. 6.CAUTION : Use of controls, adjustments or performance of procedures other than those specified here in may result in hazardous radiation exp

40、osure. REPRODUCTION AND POSITION OF LABELS CAUTION : Visible and Invisible laser radiation when open and interlock failed or defeated. AVOID DIRECT EXPOSURE TO BEAM. (e) VARNING : Synlig och osynling laserstrlning nr den ppnas och sprren r urkopplad. Betrakta ej strlen. (s) VARO : Avattaessa ja suoj

41、alukitus ohitettuna tai viallisena olet alttiina nkyvlle ja nkymttmlle lasersteilylle. Vlt steen kohdistumista suoraan itseesi. (f) ADVARSEL : Synlig og usynlig laserstrling nr maskinen er ben eller interlocken fejeler. Undg direkte eksponering til strling. (d) ! Please use enough caution not to see

42、 the beam directly or touch it in case of an adjustment or operation check. CLASS 1 LASER PRODUCT CAUTION : Visible and Invisible laser radiation when open and interlock failed or defeated. AVOID DIRECT EXPOSURE TO BEAM. (e) VARNING : Synlig och osynling laserstrlning nr den ppnas och sprren r urkop

43、plad. Betrakta ej strlen. (s) VARO : Avattaessa ja suojalukitus ohitettuna tai viallisena olet alttiina nkyvlle ja nkymttmlle lasersteilylle. Vlt steen kohdistumista suoraan itseesi. (f) ADVARSEL : Synlig og usynlig laserstrling nr maskinen er ben eller interlocken fejeler. Undg direkte eksponering

44、til strling. (d) WARNING LABEL (No.MB427)1-7 SECTION 2 SPECIFIC SERVICE INSTRUCTIONS This service manual does not describe SPECIFIC SERVICE INSTRUCTIONS. 1-8 (No.MB427) SECTION 3 DISASSEMBLY 3.1Main body section 3.1.1Removing the metal cover (See Figs. 1 to 4) (1) From the both sides of the main bod

45、y, remove the four screws A attaching the metal cover. (See Figs. 1 and 2.) (2) From the back side of the main body, remove the three screws B attaching the metal cover. (See Fig. 3.) (3) Lift the rear section of the metal cover in the direction of the arrow while extending the lower sections of the

46、 metal cov- er, release the seven claws a using a longer screwdriver from the inside as required. (See Fig. 4.) Note: Do not damage any parts and boards inside the main body when releasing the claws a using a longer screwdriver. Fig.1 Fig.2 Fig.3 Fig.4 Metal cover A Metal cover A Metal cover B Metal

47、 cover Claws aClaws a (No.MB427)1-9 3.1.2Removing the front panel assembly (See Figs. 5 and 6) Prior to performing the following procedures, remove the metal cover. (1) From the top side of the main body, disconnect the parallel wires from the connectors (CN456, CN457) on the main board. (See Fig. 5

48、.) (2) Disconnect the card wires from the connectors (CN450, CN460) on the main board. (See Fig. 5.) (3) Remove the screw C attaching the earth wires to the main board. (See Fig. 5.) Reference: When attaching the screw C, attach the earth wires with it. (See Fig. 5.) (4) From the bottom side of the

49、main body, remove the three screws D attaching the front panel assembly. (See Fig. 6.) (5) From the both and bottom sides of the main body, remove the front panel assembly in the direction of the arrow while releasing the joints b and c. (See Fig. 6.) Fig.5 Fig.6 CN456Main board C Card wire CN460 Earth wires Front panel assembly CN457 Parallel w