JVC-XVN44SL-cd-sm 电路图 维修手册.pdf

《JVC-XVN44SL-cd-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《JVC-XVN44SL-cd-sm 电路图 维修手册.pdf（83页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL COPYRIGHT 2003 VICTOR COMPANY OF JAPAN, LIMITED. No.XA003 2003/5 DVD VIDEO PLAYER XA00320035 XV-N40BKMK2, XV-N44SLMK2, XV-N4SLMK2 TABLE OF CONTENTS 1Important Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2、 . . . . . 1-4 2Disassembly method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8 3Adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3、. . . . . . . . . . . . . . . 1-15 4Description of major ICs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-24 Area Suffix (XV-N40BK,XV-N44SL) J - U.S.A. C - Canada Area Suffix (XV-N4SL) C - Canada 2 5 8 1 4 7 3 6 9 010+

4、10 CANCEL TITLE/ GROUPRETURN VFP PROGRESSIVE SCAN REPEAT ZOOM DIMMER AUDIO 3D PHONIC SUB TITLEANGLE OPEN/ CLOSEDISPLAY NEXTPREVIOUS SELECTCLEAR SLOW-SLOW+ T O P M E N U M E N U O N S C R E E N C H O I C E ENTER STANDBY/ON V I D E O This service manual is a service manual of the model which changes a

5、 part of specification of the above-mentioned model which has already been put on the market. Please refer to the following page for details. This illustration is XV-N40BK for U.S.A RadioFans.CN 收音机爱 好者资料库 1-2 (No.XA003) For this service manual This service manual is a service manual of the model wh

6、ich changes a part of specification of the above-mentioned model which has already been put on the market. The specification is different from what the label of the same model does not paste because of the specification improvement, and refer to this service manual, please. Please already refer to t

7、he issued service manual when the label is not pasted. * Please refer to this service manual for the model to which this label is pasted. * Please refer to the service manual which has already been issued for the model to which this label is not pasted. (one that there is no description named MK2 in

8、 cover of service manual. ) 0478 inside Used only service dealer Please refer to service manual of an applicable model MK2 GN30080-001A The surface of a rear panel or RadioFans.CN 收音机爱 好者资料库 (No.XA003)1-3 SPECIFICATION General Other Video outputs Audio outputs Audio characteristics Specifications an

9、d appearance are subject to change without prior notice. Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarkes of Dolby Laboratories. Manufactured under license from Digital Theater Systems, Inc. DTS and DTS Digital Surround are registered trademarks of Di

10、g- ital Theater Systems, Inc. Digital output signal chart Readable discsDVD VIDEO, DVD-R (Video format), DVDRW (Video format), +RW (Video format), SVCD, Video CD, Audio CD (CD-DA), MP3 format, JPEG, CD-R/RW (CD-DA, SVCD, Video CD, MP3 format, JPEG) Video formatNTSC, 480i (Interlaced scan)/480p (Prog

11、ressive scan) selectable Power requirementsAC 120 V, 60 Hz Power consumption10 W (POWER ON) 0.7 W (STANDBY mode) Mass2.1 kg (4.7 lbs) Dimensions (W x H x D)435mm x 53mm x 248.4mm (17-3/16 inch x 2-1/8 inc x 9-13/16 inch) COMPONENT (pin jacks)Y Output: 1.0 Vp-p (75 ) Pb/Pr Output: 0.7Vp-p (75 ) VIDEO

12、 OUT (pin jack)1.0 Vp-p (75 ) S-VIDEO OUT (S jack)Y Output: 1.0 Vp-p (75 ) C Output: 286 mVp-p (75 ) Horizontal resolution500 lines or more ANALOG OUT (pin jack)2.0 Vrms (10 k) DIGITAL OUT (COAXIAL)0.5 Vp-p (75 termination) DIGITAL OUT (OPTICAL)-21 dBm to -15 dBm (peak) Frequency responseCD (samplin

13、g frequency 44.1 kHz):2 Hz to 20 kHz DVD (sampling frequency 48 kHz):2 Hz to 22 kHz (4 Hz to 20 kHz for DTS and Dolby Digital bitstream signals) DVD (sampling frequency 96 kHz):2 Hz to 44 kHz Dynamic range16 bit: More than 98 dB 20 bit: More than 100 dB 24 bit: More than 100 dB Wow and flutterUnmeas

14、urable (less than + 0.002%) Total harmonic distortionless than 0.006% Disc typeOutput PCM ONLYDOLBY DIGITAL/PCMSTREAM/PCM DVD with 48/44.1 kHz, 16/20/24 bit linear PCM 48/44.1 kHz, 16 bit, stereo linear PCM DVD with 96 kHz, 16/22/24 bit linear PCM 48kHz, 16 bit, stereo linear PCM (Down sampling) DVD

15、 with DTSNo outputDTS bitstream DVD with Dolby Digital48 kHz, 16 bit, stereo linear PCMDolby Digital bitstream DVD with MPEG Multichannel 48 kHz, 16 bit, stereo linear PCMMPEG bitstream SVCD/Video CD/Audio CD44.1 kHz, 16 bit, stereo linear PCM Audio CD with DTSNo outputDTS bitstream CD-R/RW with MP3

16、Linear PCM RadioFans.CN 收音机爱 好者资料库 1-4 (No.XA003) SECTION 1 Important Safety Precautions 1.1Safety Precautions (1) This design of this product contains special hardware and many circuits and components specially for safety purpos- es. For continued protection, no changes should be made to the origin

17、al design unless authorized in writing by the manufacturer. Replacement parts must be identical to those used in the original circuits. Services should be per- formed by qualified personnel only. (2) Alterations of the design or circuitry of the product should not be made. Any design alterations of

18、the product should not be made. Any design alterations or additions will void the manufacturers warranty and will further relieve the manufacture of responsibility for personal injury or property damage resulting therefrom. (3) Many electrical and mechanical parts in the products have special safety

19、-related characteristics. These characteris- tics are often not evident from visual inspection nor can the protection afforded by them necessarily be obtained by us- ing replacement components rated for higher voltage, watt- age, etc. Replacement parts which have these special safety characteristics

20、 are identified in the Parts List of Ser- vice Manual. Electrical components having such features are identified by shading on the schematics and by ( ) on the Parts List in the Service Manual. The use of a substitute replacement which does not have the same safety charac- teristics as the recommend

21、ed replacement parts shown in the Parts List of Service Manual may create shock, fire, or other hazards. (4) The leads in the products are routed and dressed with ties, clamps, tubings, barriers and the like to be separated from live parts, high temperature parts, moving parts and/or sharp edges for

22、 the prevention of electric shock and fire hazard. When service is required, the original lead routing and dress should be observed, and it should be confirmed that they have been returned to normal, after reassem- bling. (5) Leakage shock hazard testing After reassembling the product, always perfor

23、m an isola- tion check on the exposed metal parts of the product (an- tenna terminals, knobs, metal cabinet, screw heads, headphone jack, control shafts, etc.) to be sure the product is safe to operate without danger of electrical shock.Do not use a line isolation transformer during this check. Plug

24、 the AC line cord directly into the AC outlet. Using a Leakage Current Tester, measure the leakage current from each exposed metal parts of the cabinet, particular- ly any exposed metal part having a return path to the chassis, to a known good earth ground. Any leakage cur- rent must not exceed 0.5m

25、A AC (r.m.s.). Alternate check method Plug the AC line cord directly into the AC outlet. Use an AC voltmeter having, 1,000 per volt or more sensitivity in the following manner. Connect a 1,500 10W resistor paralleled by a 0.15F AC-type capacitor between an ex- posed metal part and a known good earth

26、 ground. Measure the AC voltage across the resistor with the AC voltmeter. Move the resistor connection to each exposed metal part, particularly any exposed metal part having a return path to the chassis, and measure the AC voltage across the resistor. Now, reverse the plug in the AC outlet and repe

27、at each measurement. Voltage measured any must not exceed 0.75 V AC (r.m.s.). This corresponds to 0.5 mA AC (r.m.s.). 1.2Warning (1) This equipment has been designed and manufactured to meet international safety standards. (2) It is the legal responsibility of the repairer to ensure that these safet

28、y standards are maintained. (3) Repairs must be made in accordance with the relevant safety standards. (4) It is essential that safety critical components are replaced by approved parts. (5) If mains voltage selector is provided, check setting for local voltage. 1.3Caution Burrs formed during moldin

29、g may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of pre- forming repair of this system. 1.4Critical parts for safety In regard with component parts appearing on the silk-screen printed side (parts side) of the PWB diagrams, the parts that are printe

30、d over with black such as the resistor ( ), diode ( ) and ICP ( ) or identified by the mark nearby are critical for safety. When replacing them, be sure to use the parts of the same type and rating as specified by the manufacturer. (This regulation dose not Except the J and C version) Good earth gro

31、und Place this probe on each exposed metal part. AC VOLTMETER (Having 1000 ohms/volts, or more sensitivity) 1500 10W 0.15 F AC TYPE (No.XA003)1-5 1.5Preventing static electricity Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can d

32、estroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs. 1.5.1 Grounding to prevent damage by static electricity Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as DVD players. Be careful to use

33、proper grounding in the area where repairs are being performed. (1) Ground the workbench Ground the workbench by laying conductive material (such as a conductive sheet) or an iron plate over it before placing the traverse unit (optical pickup) on it. (2) Ground yourself Use an anti-static wrist stra

34、p to release any static electricity built up in your body. (3) Handling the optical pickup In order to maintain quality during transport and before installation, both sides of the laser diode on the replacement optical pickup are shorted. After replacement, return the shorted parts to their original

35、 condition. (Refer to the text.) Do not use a tester to check the condition of the laser diode in the optical pickup. The testers internal power source can easily destroy the laser diode. 1.6Handling the traverse unit (optical pickup) (1) Do not subject the traverse unit (optical pickup) to strong s

36、hocks, as it is a sensitive, complex unit. (2) Cut off the shorted part of the flexible cable using nippers, etc. after replacing the optical pickup. For specific details, refer to the replacement procedure in the text. Remove the anti-static pin when replacing the traverse unit. Be careful not to t

37、ake too long a time when attaching it to the connector. (3) Handle the flexible cable carefully as it may break when subjected to strong force. (4) I t is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn it. 1.7Precautions of the safe use of battery (Only XV-N

38、4SL) Store the battery in a place where children cannot reach.If a child accidentally swallows the battery, consult a doctorimmediately. Do not recharge, short, disassemble or heat the battery or dispose of it in a fire. Doing any of these things may cause the battery to give off heat, crack, or sta

39、rt a fire. Do not leave the battery with other metallic materials.Doing this may cause the battery to give off heat, crack, or start a fire. When throwing away or saving the battery, wrap it in tape and insulate; otherwise, the battery may start to give off heat, crack, or start a fire. Do not poke

40、the battery with tweezers or similar tools.Doing this may cause the battery to give off heat, crack, or start a fire. Dispose of batteries in the proper manner, according to federal, state, and local regulations. 1-6 (No.XA003) 1.8Importance admistering point on the safety C701 C706 C902 C904 C905 C

41、907 C908 C913 C914 C918 C950 C951 C953 C955 C957 B34 C959 B139 C965 C966 C967 B15 C973 C974 C975 B276 C977 B772 C988 B4 D901 CP951 D701 D953 CN901 D904 B873 B166 C906 EP951 FC901 FC902 IC901 IC952 J702 L709 L710 L901 L951 L952 L954 B116 L955 B532 C976 P901 B138 PC901 Q953 B45 R901 R903 R906 R910 R91

42、2 R913 R953 R954 S901 T901 X701 S902 C952 B234 C970 B236 D956 B137 L956 L957 L959 B333 B533 B771 B32 B852 B874 B872 B871 B140 B272 B332 B601 B601 B141 B16 B331 B136 B403 B271 B38 B39 B36 B142 B143 B40 B133 B134 B132 B202 B231 B233 B105 B103 B101 D955 B303 B135 CN902 B273 B631 B37 L953 R966 R951 R915

43、 B2 B237 Q951 B203 B102 C958 D957 D954 D952 D951 D903 D902 B347 EP952 C963 C964 B107 B205 EP953 R969 C808 C802 CN904 B170 D702 K813 K811 K810 K812 K814 Full Fuse Replacement Marking Graphic symbol mark (This symbol means fast blow type fuse.) should be read as follows ; FUSE CAUTION FOR CONTINUED PR

44、OTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE AND RATING OF FUSES ; F901 : 1.6 A / 125 VF901 : 1.6 A / 125 V Marquage Pour Le Remplacement Complet De Fusible PRECAUTIONS SUR LES FUSIBLES POUR UNE PROTECTION CONTINUE CONTRE DES RISQUES DINCENDIE, REMPLACER SEULEMENT PAR UN FUSIBLE DU MEM

45、E TYPE ; Le symbole graphique (Ce symbole signifie fusible de type a fusion rapide.) doit etre interprete comme suit ; (No.XA003)1-7 1.9Precautions for Service 1.9.1Handling of Traverse Unit and Laser Pickup (1) Do not touch any peripheral element of the pickup or the actuator. (2) The traverse unit

46、 and the pickup are precision devices and therefore must not be subjected to strong shock. (3) Do not use a tester to examine the laser diode. (The diode can easily be destroyed by the internal power supply of the tester.) (4) To replace the traverse unit, pull out the metal short pin for protection

47、 from charging. (5) When replacing the pickup, after mounting a new pickup, remove the solder on the short land which is provided at the center of the flexible wire to open the circuit. (6) Half-fixed resistors for laser power adjustment are adjusted in pairs at shipment to match the characteristics

48、 of the optical block. Do not change the setting of these half-fixed resistors for laser power adjustment. 1.9.2Destruction of Traverse Unit and Laser Pickup by Static Electricity Laser diodes are easily destroyed by static electricity charged on clothingor the human body. Before repairing periphera

49、l elements of the traverse unit or pickup, be sure to take the following electrostatic protection: (1) Wear an antistatic wrist wrap. (2) With a conductive sheet or a steel plate on the workbench on which the traverse unit or the pick up is to be repaired, ground the sheet or the plate. (3) It solders to two short circuit sections on the