Kenwood-DVF-3030-Service-Manual 电路图 维修手册.pdf

《Kenwood-DVF-3030-Service-Manual 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Kenwood-DVF-3030-Service-Manual 电路图 维修手册.pdf（53页珍藏版）》请在收音机爱好者资料库上搜索。

1、70% In compliance with Federal Regulations, following are repro- duction of labels on, or inside the product relating to laser product safety. KENWOOD-Crop. certifies this equipment conforms to DHHS Regulations No.21 CFR 1040. 10, Chapter 1, subchapter J. DANGER : Laser radiation when open and inter

2、lock defeated. AVOID DIRECT EXPOSURE TO BEAM. Caution : No connection of ground line if disassemble the unit. Please connect the ground line on rear panel, PCBs, Chassis and some others. NOTE : Please use the remote controller for self-diagnosis. DIGITAL OUTPUT (PCM/BIT STREAM) OPTICAL AUDIO OUTPUT

3、SUB WOOFER VIDEO OUTPUT S-VIDEO AC IN L R AV DVD VCD CD PLAYER DVF-3030 SERVICE MANUAL 2000-6/B51-5645-00 (K/K) 1405 Holder P (J19-6058-08) Front panel * (A60-) Tray top * (A29-) Top cover * (A01-) Legx4 (J02-1468-08) Y/C connector (E40-8534-08) Connector (21P) (E40-8598-08) AC inlet * (E40-) Pin ja

4、ck (E63-1170-08) * Refer to parts list on page 61. RadioFans.CN 收音机爱 好者资料库 (A70-1444-08) Battery cover (A09-1193-08) (E30-2946-08): E (E30-2977-08): X (E30-2938-08)(B19-1615-08) Remote control unit . . . . . . . . . 1 for remote control unit size AA Batteries. . . . . . . . . . . . . . . . . . . . 2

5、AC cord . . . . . . . . . . . . . . . . . . . . . 1 Video/audio cable. . . . . . . . . . . . 1Digital cord. . . . . . . . . . . . . . . . . . . 1 DVF-3030 2 CONTENTS / ACCESSORIES CONTENTS / ACCESSORIES . 2 DISASSEMBLY FOR REPAIR.3 BLOCK DIAGRAM .12 CIRCUIT DESCRIPTION.16 ADJUSTMENT.18 VOLTAGE CHART

6、.19 WIRING DIAGRAM.23 PARTS DESCRIPTIONS .24 PC BOARD . 25 SCHEMATIC DIAGRAM . 31 EXPLODED VIEW .58 PARTS LIST.61 SPECIFICATIONS .Back cover Contents Accessories Note: There is different part in this manual as compared with a usual one because we use OEM factorys data. On Circuit description, Lubric

7、ation and Abbreviation of Logo, please refer to DV-303 service manual (B51-5561-00 or B51-5583-00) How to read the schematic diagram There are some destinations in this schematic. Connection of from or to. Port name RadioFans.CN 收音机爱 好者资料库 DVF-3030 3 DISASSEMBLY FOR REPAIR Extension cable(C) Extensi

8、on cable(B)x2 Extension cable(A) 1-1 Casing Parts and C.B.A. Positions 1. Assembling and Disassembling the Casing and Checking C.B.A.s 1-4 Disassembling the Front Panel 1. Release the 3 tabs on the bottom. 2. Release the 2 tabs on the left and right. 3. Release the 2 tabs. 4. Disconnect the 2 flexib

9、le cables. 1-5 Disassembling the Loading Base Unit 1. Remove the 4 screws. 2. Pull out the loading base unit vertically. Note There is a danger of damaging the connectors. 1-2 Service Positions Note To inspect the loading base unit, position the left side upward (as viewed from the front). 1-3 Disas

10、sembling the Tray 1. Turn the lever clockwise. 2. Move the tray in the direction of the arrow until it locks. 3. Release the tab locks on the left and right, then pull out the tray. Module C.B.A. * E type has SCART pcb. RadioFans.CN 收音机爱 好者资料库 DVF-3030 4 DISASSEMBLY FOR REPAIR Extension cable(C) Ext

11、ension cable(B) Extension cable(B) 1-6 Checking the Module C.B.A. 1. Remove the screws. 2. Connect the module C.B.A. to the mother C.B.A. with the extension cables for inspection. Extension cable (B)x2 Mother C.B.A. Module C.B.A. PP4201-PS4201 PP3201-PS3201 3. Connect the mechanism loading C.B.A. to

12、 the mother C.B.A. with the extension cable: for inspection. Extension cable(C) Mother C.B.A. Mechanism Loading C.B.A. PP2591-PS2591 Note Be sure to initialize the player whenever you replace a C.B.A. (Refer to page17/4-1 Initializing the DVD Player.) 1-7 Disassembling the Rear Panel, 1. Remove all

13、of the screws connected to the rear panel. (The number of screws varies according to the model). 1-8 Checking the Power Supply C.B.A. 1. Remove the 3 screws. 2. Carefully pull out the power supply C.B.A. Note There is a danger of damaging the connectors. 3. Connect the power supply C.B.A. and the mo

14、ther C.B.A. with the extension cable for inspection. Extension cable(A) (connects the power supply C.B.A. PS1101 and the mother C.B.A. PP1101) 2. Release the two tabs on the left and right. Extension cable(A) DVF-3030 5 DISASSEMBLY FOR REPAIR Extension cable(C) Extension cable(B) Extension cable(B)

15、1-9 Checking the Mother C.B.A. 1. Remove the 4 screws. 2. Release the 2 tabs. 2. Assembling and Disassembling the Optical Pickup (Mechanical Parts) The optical pickup can be damaged by static electricity from your body. Be sure to take static electricity countermeasures when working around the optic

16、al pickup. 2-1 Handling the Optical Pickup The optical pickup can be damaged by static electricity from your body. Be sure to take static electricity counter- measures when working around the optical pickup. 1. The optical pickup is an extremely high-precision mecha- nism. Do not subject it to stron

17、g impact. 2. To preserve the quality of the optical pickup replacement parts during transport and installation, the terminals of the laser diode are short-circuited. After replacing the parts, use the proper procedure to return the laser diode to its original condition. (Refer to page8/2-11 Assembli

18、ng the Optical Pickup.) 3. Testers cannot be used to check the laser diode of the optical pickup. The power supply inside the tester can easily damage the laser diode. 4. Take care when handling the flexible cable because excessive force can cause it to break. 5. You cannot adjust the semifixed resi

19、stor for laser power adjustment. Do not turn it. 2-2 Disassembly Procedure Use the following procedure to replace major parts. For the assembly procedure, follow the flow chart in reverse. 3. Checked by connecting the module C.B.A. and the moth- er C.B.A. with the extension cables. Extension cable (

20、B)x2 Module C.B.A. Mother C.B.A. PS3201-PP3201 PS4201-PP4201 4. Checked by connecting the mechanism loading C.B.A. and the mother C.B.A. with the extension cables. Extension cable(C) Mechanism Loading C.B.A. Mother C.B.A. PS2591-PP4201 Note Be sure to initialize the player whenever you replace a C.B

21、.A. (Refer to page17/4-1, Initializing the DVD player.) DVF-3030 6 DISASSEMBLY FOR REPAIR 2-3 Static Electricity Countermeasures The laser diode inside the traverse unit (optical pickup) can be damaged by static electricity from your body. Be sure to take static electricity countermeasures when work

22、ing around the optical pickup. 2-3-1 Static Electricity Countermeasure Methods 1. Ground yourself Use an anti-static wrist strap to discharge static electrici- ty from your body. 2. Ground the workbench Lay a conductive material (sheet) or steel sheet on the surface where the traverse unit (optical

23、pickup) is to be placed, then ground the sheet. 2-4 Disassembling the Clamp Base Unit Remove the 2 screws. 2-5 Disassembling the Clamper Weight, Clamper Yoke, Magnet and Clamper 1. Release the tab, and pull out the clamper. 2. Release the 3 tabs on the clamper. 2-3-2 Short-circuit the laser diode So

24、lder the land in the flexible cable of the optical pickup. Notes Be sure to do this before disconnecting the flexible cable of the optical pickup from the module C.B.A. Use an anti-static soldering iron to short-circuit and unshort-circuit laser diode. (Recommended soldering iron: Hakko with ESD cou

25、nter- measure) After you have finished repairing the laser diode, follow the correct procedure to remove the solder from the short-circuit location. (Refer to page5/2. Assembling and Disassembling the Optical Pickup (Mechanical Parts).) DVF-3030 7 DISASSEMBLY FOR REPAIR 2-6 Disassembling the Travers

26、e Unit 1. Remove the 3 screws. Note Be sure to take static electricity countermeasures befer disconnecting the flexible cable.(Refer to page6/2-3 Stat- ic Electricity Countermeasures.) 2. Disconnect the 2 flexible cables. 2-7 Disassembling the Stepping Motor Unit 1. Disconnect the flexible cable. 2.

27、 Remove the 2 screws. Note Take care when handling the flexible cable because it can be broken by excessive force. 2-8 Disassembling the Optical Pickup Unit 1. Remove the screw. 2. Release the tab, then remove spring holder 1. Note Be sure not to lose the spring. 3. Remove the guide shaft. Note Be s

28、ure to adjust the optical pickup tilt after replacing the optical pickup. (Refer to page9/2-13 Optical Pickup Tilt Adjustment.) DVF-3030 8 DISASSEMBLY FOR REPAIR 2-9 Disassembling the Nut Unit 1. Remove the screw. Notes The nut unit is not part of the optical pickup. Before replacing the optical pic

29、kup, remove the nut unit for use with the new optical pickup. After installation, use screw lock to lock the screw in posi- tion. When reassembling, use screw lock to lock the screw in position after attaching it. 2-11 Assembling the Optical Pickup 1. Install the optical pickup. Note Take care not o

30、t attach the tilt spring and guide shaft in the wrong order. 2-10 Disassembling the Sub-Shaft Preload Spring 1. Remove the screw. Notes Handle the sub-shaft preload spring carefully because the shape of the tip is easily deformed. The sub-shaft preload spring is not part of the optical pickup. Befor

31、e replacing the optical pickup, remove the sub-shaft preload spring for use with the new optical pickup. After installation, use screw lock to lock the screw in posi- tion. 2. Insert the pickup FPC into connector FP5201 on the mod- ule C.B.A. DVF-3030 9 DISASSEMBLY FOR REPAIR 2-13 Optical Pickup Til

32、t Adjustment3. Remove the solder from the pickup FPCs soldered short- circuit. 4. Adjust the optical pickup tilt after removing the solder. (Refer to page 9/2-13 Optical Pickup Tilt Adjustment.) 2-12 Disassembling the Spindle Motor Unit 1. Remove the three screws. Note Be sure to adjust the optical

33、pickup tilt after replacing the spindle motor unit. DVF-3030 10 DISASSEMBLY FOR REPAIR Notes Adjustment is generally unnecessary after replacing other parts of the traverse unit. However, adjust if there is a noticeable degradation in picture quality. Optical adjustments cannot be made inside the op

34、tical pickup. Adjustment is generally unnecessary after replacing the traverse unit. D 11 DVF-3030 DISASSEMBLY FOR REPAIR 2-14 Disassembling the Intermediate Chassis 1. Push the stopper downward, then rotate it until it contacts the Vertical cam. 2. Release the 2 tabs. 2-16 Disassembling the Pulley

35、Gear and Deceleration Gear 1. Remove the screw. 2. Remove the pulley gear. 3. Remove the belt. 4. Remove the deceleration gear. 2-17 Disassembling the Mechanism Loading C.B.A. 1. Remove the 2 screws. 2. Remove the 2 screws. 3. Release the three tabs. 2-15 Disassembling the Vertical cam and Drive gea

36、r 1. Rotate the Vertical cam until it reaches the contact position. 2. Lift the Vertical cam straight upward to pull it out. 3. Remove the Drive gear. ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?

37、 ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?

38、 ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?

39、 ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?