Kenwood-KD-CPSW-9531-Y-Service-Manual 电路图 维修手册.pdf

《Kenwood-KD-CPSW-9531-Y-Service-Manual 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Kenwood-KD-CPSW-9531-Y-Service-Manual 电路图 维修手册.pdf（52页珍藏版）》请在收音机爱好者资料库上搜索。

1、 2005-6 PRINTED IN JAPAN B53-0296-00 (N) 1703 CD RECEIVER KDC-MP928 KDC-PSW9531/PSW9531Y XXV-01D SERVICE MANUAL XXV-01D KDC-PSW9531/PSW9531Y K type E type K type E,M type K type E type KDC-MP928 SIZE AA BATTERY (Not supplied) Compact disc * (W01-1643-15) :K,M (W01-1647-05) :E Plastic cabinet assy (A

2、02-2749-03) Remote controller assy(RC-527) (A70-2067-05) Escutcheon (B07-3125-01) Mounting hardware assy (J21-9716-03) DC cord * (E30-6412-05) :E DC cord * (E30-6408-05) :K,M (E30-6414-05) :KDC-MP928 Lever (D10-4589-04) X2 Cleaning cloth * (W01-1649-05) Antenna adaptor * (T90-0523-05) Screw set * (N

3、99-1758-05) Screw (N09-6280-05) * Depends on the model. Refer to the parts list. CD MECHANISM EXTENSION CORD (24P) : W05-0934-00 A unique identification number (Unique ID) is given to each unit, which is imprinted on the CD mechanism assembly. If and when the mechanism assembly or Flash ROM (IC17) o

4、n the mechanism board is replaced, it is necessary to write the Unique ID. For details, refer to “How to Write the Unique ID” on Page 18. MODELTDF PANEL No.TDF NAME KDC-MP929Y33-2350-60 TDF-MP59D KDC-W9531/W9531YY33-2350-62 TDF-W9531 XXV-01D (K,M type)Y33-2350-61 TDF-XXV01DX XXV-01D (E type)Y33-2350

5、-63 TDF-XXV01D TDF PANEL INFORMATION This product uses Lead Free solder. RadioFans.CN 收音机爱 好者资料库 2 KDC-MP928/PSW9531 /PSW9531Y, XXV-01D BLOCK DIAGRAM F/E CD LX SW5V AM+B AGC RDS DECODER MEMO INSTALLER ROM CORR D3.3V A3.3V DRIVER MUTE LPFDAC D5V A5V A3.3V MUTE PRE SERGE PROTECTION OP AMP LEVEL SHIFT

6、DSP ADC IC301,302IC305IC303IC306-308 IC102 IC300 IC RESET P-CON ANT-CON DIMMER EXT AMP B.U DET SERGE DET ACC DET TEL MUTE SW 16V ILL+B A8V SW 14V BU5V PAN3.3V SW 16V OEL +B SERVO SW 5V (5VPRE) DC/DC MOTOR +B 5V PANEL MOTOR DRIVERMECHA PANEL OPEN/ PANEL DET 3.3V DRIVE COMP POWER IC DSI 3.3V 2.5V ROMC

7、OR E2P ROM SW (16x64kBIT) SRAMFLASHROM (16x8MBIT) OEL MODULE (256x64PIX. 4096COLOR) IR REMO CON ANA. SPE. (6BAND) BU5V A8V D5V SERVO BACK u-COM E-VOL u-COM (FST) BUS LPF IC400 IC104 IC4 IC750 CD D5V A8V A8V SW5V UP BU5V A8V BU5V REF SVR BU5V D3.3V BU5V A8V 9V CLOSE SW5V SERVO SW SWSWSWSWSW SW SW LEV

8、EL SHIFT 9V D5V SHIFT LEVEL IC RESET AUX IN PRE OUT(REAR) SP OUT(FR) OPEL DISP P CON ANT CON EXT. AMP. CON DIMMER LINE ACC BACK UP KEYS RESET JOG ROTARY BU5V PRE OUT(FRONT) PRE OUT(SW) SP OUT(FL) SP OUT(RL) SP OUT(RR) WIRED REMO ILL+B E2P ROM FST AUX FM/AM CD CH SPE ANA MPX for RDS MUTE 0,1,2 WININ

9、DCERR MUTE A,C MUTE A,C RST STBY OFFSET MUTE 0,1,2 PRE MUTE RST E2P P-ON ROM P-ON I2C BUS RESET A1-A23 D0-D15 GREEN KEY ILL KEY ILL RED SUB ILL BLUE(R) SUB ILL BLUE(L) TRIANGLE ILL CONT. KEY SCAN KEY IN P-ON 5V A/D 7CH CW. CCW SPE ANA 5V SYSTEM 3.3V SYSTEM PANEL ELECTRIC UNIT (X34-356) RadioFans.CN

10、收音机爱 好者资料库 3 KDC-MP928/PSW9531 /PSW9531Y, XXV-01D BLOCK DIAGRAM TR COIL FO COIL C F AB E PD LD SERVO DSP MOTOR DRIVER SP MOTOR LOADING by long-pressing for 2 seconds, all error log information is cleared. (Display) I2C_ (Display) ERR_1-, 2-, 3- In “”, “OK” or “NG” is displayed. In “”, “ ” or an erro

11、r code is displayed. (*1) One count is made when the panel opens to full or when a disc is loaded. CE DATA CLK 500msec 500msec 500msec G sensor display items When source is STANDBY, by short-pressing ATT key, the display is switched to analogy meter display, in which verti- cal G and horizontal G ar

12、e displayed. Special display when all lights are on When all lights are on with the STANDBY source, the fol- lowing displays are made when the keys shown below are pressed. 16 KDC-MP928/PSW9531 /PSW9531Y, XXV-01D TEST MODE Initializing AUDIO-related value setting During STANDBY sourcing, by short-pr

13、essing key, AU- DIO setting values are returned to the default values. Flash ROM/Static RAM check 1. When entering the test mode, the manufacture code of the Flash ROM (16M) is read and when it is normal, FROMCHK terminal of the 100pin repeats HiLowHi . If the read- ing is abnormal, “Low” is output.

14、 If the manufacture code is normal, by short-pressing key, the connection checks on all terminal is started. If the connections are normal, the FROMCHK terminal stops the HiLowHi repeating and outputs “Hi.” If the reading is abnormal, “Low” is output. 2. With all lights turned on and by long-pressin

15、g AM key, the data on the Flash ROM (16M) is initialized. While erasing the data, “Data_Erase. . . .” is displayed. Note : Do not touch any key white this is in progress. When erasing is complete, “Erase_OK!” is displayed. If “Erase_NG!” is displayed, it was not possible to erase the data on the Fla

16、sh ROM (16M). In this case, long-pressing AM key again. If it is the same, then there is an abnormality with the Flash ROM. 3. Regardless of the state of the test mode, when the power is turned on, the manufacture code on the Static RAM is read and, when, normal, Hi is output by the SRAMCHK terminal

17、. When abnormal, Low is output. Other At Power ON “CODE_OFF”, “CODE_ON” displays will not be made. When sourcing STANDBY, by short-pressing AUTO / TI key, GREEN/RED of the key illumination is switched. When staring up in the test mode, LINE MUTE prohibition time is set to 1 second instead of 10 seco

18、nds. While in the test mode, security jig should not be used to write the security code. While in the test mode, serial writing jig should not be used to write the serial number. While in the test mode, even when a DC error is detected, the detection information will not be written to the E2PROM. Wh

19、ile in the test mode, even after an elapse of pre-set time, the backup memory items will not be written to the E2PROM. Information Clear mode for Test Mode, backup/installer memory, and CD mechanism error log. In the DC error de- tection information clear mode, DEMO mode operation will not be conduc

20、ted. Also, in the above mode, the menu of the STANDBY source will not display DEMO ON/OFF switching items. While in the test mode, and at the same time, PM_DET terminal is H, the following will apply to the EJECT key, regardless of whether a disc is in the unit or not. Panel full OPEN/CLOSE is condu

21、cted with a short-push. (Protection time: 3 seconds) As far as this item is concerned, eject will be achieved by 1 second long-push on the EJECT key. Clearing backup memory and installer memory data (Clearing E2PROM data) 1. By pressing NEXT key and ATT key simultaneously, re- set and start the unit

22、. This will start the initialization pro- cesses for backup and installer memory data and the error log information of the CD mechanism. 2. When initialization is complete, the following display will be made. Normal completion Abnormal ending 1 backup/installer memory initialization: NG Abnormal end

23、ing 2 CD mechanism error log initialization: NG Abnormal ending 3 All initialization: NG 3. While in this mode, even after an elapse of a pre-set time, no backup memory items will be written to the E2PROM. 4. This mode is released by resetting. (What was on the last screen will not be retained.) CD_

24、E2P_ : AUDIO_E2P : CD_E2P_ : AUDIO_E2P : CD_E2P_ : AUDIO_E2P : CD_E2P_ : AUDIO_E2P : 17 KDC-MP928/PSW9531 /PSW9531Y, XXV-01D TEST MODE Clearing DC error detection information (E2PROM data clear) 1. By resetting, while pressing both ATT key and AUD key simultaneously, enter the DC error display mode.

25、 2. During STANDBY sourcing, the current DC error conditions will be displayed. When error detected : “DC_ERR” When error not detected : “DC_OK” 3. While the error conditions are being displayed, short-press AUTO or TI key to clear the detection information. (E2PROM clear) 4. DC Error Display mode i

26、s released by resetting. (What was on the last screen will not be retained.) Frequency span switching (K / M type) During Power OFF, while pressing both ATT key and TI/ AUTO key simultaneously, turn the power on while press- ing SRC key. Security Forced Power ON mode (All models) Even in the cases w

27、here security is authorized, by resetting while pressing NEXT key and TI/AUTO key simulta- neously, it is possible to turn the power ON for 30 minutes only. After the elapse of 30 minutes, it is possible to start with resetting only. How to register the security code after replace- ment of the E2PRO

28、M (F/E) (Code security models) 1. Enter the test mode. (Refer to the section on “How to Enter the Test Mode.”) 2. Enter the MENU by long pressing NEXT key for one sec- ond. While “Security” is being displayed, long-press key for one second and enter the security registration mode. 3. Using FM / AM /

29、 / keys, enter the code. FM key : Number upAM key : Number down key : Cursor Right key : Cursor Left 4. Press key for 3 seconds to display “RE-ENTER”. Then, re-enter the code using the method in above 4. 5. Press key for 3 seconds to display “APPROVED”. 6. Release the test mode. (Refer to the sectio

30、n on “How to Release the Test Mode”.) Note : The security code for this model cannot be deleted by “all clear” command. Method of clearing simple security code 1. When you are requested to enter the security code, while pressing down on AUTO key, use a long-press on key for 3 seconds. ( disappears.)

31、 2. Using the remote controller, input “KCAR”. Press remote controller 5 key 2 times and then press key. (Input for “K”.) Press remote controller 2 key 3 times and then press key. (Input for “C”.) Press remote controller 2 key once and then press key. (Input for “A”.) Press remote controller 7 key 2

32、 times and then press key. (Input for “R”.) 3. The security is released and the unit enters the STANDBY mode. 4. If a wrong code is input, the unit goes into the Code Re- quest mode. Special operation on the multi-function (multi- function operation that does not use the rotary encoder) Obtaining Tu

33、ner preset by the unit operation 1. Enter the test mode. (Refer to the section on “How to enter the test mode”.) 2. Set to the “Tuner source”. 3. Press the NEXT key, to display the source-related multi- function key. 4. Use the FM key or AM key to move the cursor to the preset number desired. 5. By

34、short-pressing the AUD key, and using the cursor, ob- tain the preset frequency. DSP Bypass/Through switching 1. Enter the test mode. (Refer to the section on “How to enter the test mode”.) 2. Set to the “Tuner source”. 3. Press the NEXT key, to display the source-related multi- function key. 4. Use

35、 the FM key or AM key to move the cursor to the DSP items. 5. By short-pressing the AUD key, switch DSP Bypass/ Through. 18 KDC-MP928/PSW9531 /PSW9531Y, XXV-01D HOW TO WRITE THE UNIQUE ID 1. Introduction The Unique ID is an identification code allocated to each DXM- 6800 mechanism unit. When written

36、 to the mechanism unit, the ID is stored in the Flash memory area, managed by the DSP. During servicing of the unit, if and when the mechanism as- sembly is replaced, the Unique ID of the old unit should be written to the new mechanism assembly. At the same time, after moving the Unique ID, the ID s

37、eal must also be moved. The descriptions herein concern writing Unique ID, using the functions of the DXM-6800 mechanism. It is possible to easily re-write the Unique ID of the mechanism, using this function. * DXM-6800 : X92-5100-00 2. Unique ID The Unique ID is an identification code allocated to

38、each DXM- 6800 mechanism unit. This ID is consisted of 8-digit hexadeci- mal numbers. Example : 9F346D22, 352899AC, etc. The ID number seal is placed on top of the mechanism cabi- net. The 8-digit numbers and characters are the Unique ID assigned to the mechanism. The Unique ID can be confirmed in t

39、he MENU mode. 3. How to write the Unique ID, using the unit In this section, the procedure for writing the Unique ID with the unit is explained. Since this procedure is realized by put- ting the mechanism into a special mode, the unit must first be reset, immediately before conducting the procedure.

40、 At the same time, the display mode of the unit must be set to P- Time, prior to shifting into the write mode. Unless set to P- time, 5 seconds after shifting into the write mode, ID digits and ID numbers will be stopped from displaying. (Please refer to the instruction manual as for the setting met

41、hod for P-Time.) 3-1. How to shift into the Unique ID writing mode using the unit Procedure 1. Set the 63pin of the mechanism microcomputer (91CU27UG5UR8) to High. (Connect X32 : IC1 63pin and Back Up 3.3V with a lead.) Procedure 2. Reset the mechanism microcomputer and boot it up again. (Resetting

42、the mechanism microcomputer and booting it up again can be achieved by cutting off ACC and Back Up power supply once and then re-starting the unit.) Procedure 3. Insert a CD and use it as a source (i.e. let the unit start reading the Disc.) Procedure 4. This completes the start up on Unique ID Write

43、 mode. After shifting into the Unique ID Write mode, the display will be as shown in the figure below. (In the Unique ID Write mode, actually, w is displayed first and, after pressing FF key once in the Write mode, q is dis- played.) Figure1Initial display of the Unique ID Write mode Where, q Unique

44、 ID The contents of what are indicated by x : xx in the time code is the actual contents of the Unique ID. In sections of minutes : seconds, the Unique ID is indicated in decimal numbers. The table below is the correspondence between the decimal and hexadecimal numbers. Decimal numbers00010203040506

45、07 Hexadecimal numbers01234567 Decimal numbers0809101112131415 Hexadecimal numbers89ABCDEF IC1 1 1 1 1 1 D5V BO RE TX BU3.3 A3 A2 A1 A0 GND RX 63pin J76-0060-12 X32-5730-00 0-01 DXM-6800W T-12 w0:00 q 19 KDC-MP928/PSW9531 /PSW9531Y, XXV-01D HOW TO WRITE THE UNIQUE ID The Unique ID indicated in the m

46、inutes section is the target Unique ID of the current procedure for writing the ID. The Unique ID in the seconds section indicates the next Unique ID that is to replace the current Unique ID. The digit numbers of the Unique ID will be displayed in the Track Number section of w. w Unique ID digit num

47、ber : The digit numbers of the Unique ID are numbered 1, 2, 3,. from the left side of the Unique ID. The contents indicated by T-xx in the track number section are the digit number of the Unique ID displayed currently in q. The first digit is the digit number of the Unique ID, which is currently wor

48、ked upon and displayed in the minute section of the time code. The second digit is the next digit number of the Unique ID, which is indicated in the seconds section of the time code. The values of the T-xx will be changed as the tar- get of the changed Unique ID is moved in the following man- ner :

49、T-12 T-23 T-34 T-45 . T-78 T-81 . The value in the higher digit (i.e. “1” of T-12, for example) is the current target for change in the Unique ID. After the Unique ID has been changed in all of its digits and as the writing takes place, the progress condition of writing is indicated in the w section. The display contents are; T-99 : Unique ID writing in progress. T-11 : Unique ID Writing complete (success) T-22 : Unique ID Writing complete (failure) Procedure 5. Changing Unique ID write contents Using