《Kenwood-KDCX-915-Service-Manual(2) 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Kenwood-KDCX-915-Service-Manual(2) 电路图 维修手册.pdf（27页珍藏版）》请在收音机爱好者资料库上搜索。
1、 2000-1 PRINTED IN JAPAN B51-7571-00(S) 3448 SERVICE MANUAL CD RECEIVER KDC-X915/X815 PS9016R/PS9080R Extension cordParts No. CD mechanism(22P)W05-0618-00 The MECHANISM OPERATION DESCRIPTION is the same as model KDC-S3007 and KDC-5050RG. Please refer to the service manual for model KDC-S3007(B51-702
2、9-00) or KDC-5050RG(B51-7099-00). Lever x2 (D10-4301-14) (D10-4302-14) Bracket (J19-4875-04) (J19-4876-04) (E30-4779-05):KDC-X815 (E30-4781-05):KDC-PS9016R (E30-4782-05):KDC-X915 Screw set (N99-1652-05) Stay (J54-0606-04) Mounting hardware assy (J21-9491-03) Screw set (N99-1683-05) (E30-4788-05):KDC
3、-PS9080R Plastic cabinet assy (A02-1489-03) KDC-X915 DISP Escutcheon (B07-2183-02) GKDC-X915 Front glass (B10-3107-01) Panel assy (A64-1867-02) : Refer to the Parts List RadioFans.CN 收音机爱 好者资料库 KDC-X915/X815/PS9016R/PS9080R COM+B FM+B AM+B E2PROM DIMMER 2WAY MUTE ACC DET. SRMPHOT BU DET. SRM DRIVER
4、A8V SERVO DC/DC SW14V SW5VBU5V P CON ANT-CON MUTE DRIVER 4.5V PREMUTE Es POWER IC IC4 IC14 u-com IC1 CD CH IC10 IC7-9 IC5 IC2 F/E MECHADET. E-VOL PREOUT SP-OUT DIMMER TEL-MUTE ACC ANT-CONT P-CON BACK UP DECORDER RDS IC11 IC16 EX.AMP CONTROL AVR DC/DC BOX PANEL u-com RESET SW RESET IC VFD REMOG/R SW
5、SPEANA IC15 ANT. IN AMP IC12 NOISE PREOUT OUTPUT VOLTAGE SPEANA AGC OPAMP CONTROL EX.AMP NAVI-MUTE PANEL 5V 4.5VPRE IC3 IC6 DC/DC REG MATRIX KEY LOCK SW PANEL BFP FL TYPE PLL CLK CH MO SW SERVO+B LO/EJ STOP MUTE DATA S CLK SW2 CS SQR DATA M SW3 SW1 A8V BU5V RST REQ C CLK CH-CON DATA H REQ H CD AM FM
6、 MUTE MC REQ PANEL RST SC REQ MC CLK SC DATA RESET SRM SW1 SRM DET SRM SW2 RDCK RDDA QUAL SDA SCL A8V +B -B +B -B PLL DATA PLL CE S-METER SW5V SW5V DATA C BACK UP PANEL 5V FAC FL+B 750mV 4500mVCHANGER AM 4.5V PRE 2250mVFM 160mV 1200mV 1200mV 213mV (E TYPE) 400mV (K TYPE) RDS OUT FM+B NOISE 4500mVCD
7、K TYPEMODE 4500mV 4500mV 1069mV 1715mV E TYPE 3600mV 600mV 1800mV 3600mV K TYPEE TYPE 3600mV 1372mV 855mV 3600mV 1.8V PRE SRM SUB- SRM SUB+ DRIVER MUTE BU5V DC/DC IS FL ONLY RST 2 BLOCK DIAGRAM RadioFans.CN 收音机爱 好者资料库 MICROCOMPUTERS DESCRIPTION System -com: UPD784217GC GTerminal description No.Pin n
8、ameFunctionI/ODescriptionProcessing Operation 1P120/RTP0CHCON1OChanger 1 controlActive: Hi 2P121/RTP1CH_MUTEIChanger muting inputMUTE Requested : Hi 3P122/RTP2REQHOHandshake request to changersActive: Lo 4P123/RTP3ILL_ONOIllumination outputActive: Hi 5P124/RTP4NCOOpen 6P125/RTP5CD_SW2I12cm DISC dete
9、ctionON: Lo 7P126/RTP6CD_SW1ILoading detectionON: Lo 8P127/RTP7NCOOpen 9VddVdd-Positive power supply 10X2X2-Main clock connection 11X1X1-Main clock connection 12VssVss-GND 13XT2XT2-Sub clock connection 14XT1XT1-Sub clock connection 15RESETRESETIReset inputActive: Lo 16P00/INTP0CH_RSTOChanger reset o
10、utputActive: Lo 17P01/INTP1R_CLKIRDS clock input 18P02/INTP2/NMIREQCIHandshake request from changerActive: Lo 19P03/INTP3NCI/O 20P04/INTP4NCI/O 21P05/INTP5NCI/O 22P06/INTP6SC_REQIHandshake request from panel -com 23AVddAVdd-A/D analog power supply 24AVref0AVref-A/D reference voltage input 25P10/AN10
11、PHONEIPHONE detection terminal1V or less: PHONE 2.5V or more: NAVI MUTE 26P11/ANI1SRM_SW1ISRM position detectionOpen: Hi 27P12/ANI2NOISEIFM noise detectionAnalog input 28P13/ANI3SMETERIFM signal meter detectionAnalog input 29P14/ANI4IF_MODEIK2I IF selectorWide: Hi/Narrow: Lo 30P15/ANI5NCIGND 31P16/A
12、NI6M_MUTE_RIMute request from mechanismMute requested: Lo 32P17/ANI7M_MUTE_LIMute request from mechanismMute requested: Lo 33AVssAVss-A/D GND 34P130/ANO0EXT_AMPOEXT_AMP control 35P131/ANO1M_RSTOReset output to mechanismReset: Lo 36AVref1-D/A reference voltage input 37P70/RxD2/SI2DATACIData line from
13、 changer 38P71/TxD2/SO2DATAHOData line to changer 39P72/ASCK2/SCK2CH_CLKI/OClock line from/to changer 40P20/RxD1/SI1L_DATAL/SC_DATAIData line from LCD driver 41P21/TxD1/SO1L_DATAS/MC_DATAI/OData line to LCD driver 42P22/ASCK1/SCK1L_CLK/MC_CLKI/OClock line to LCD driver 43P23/PCLM_STOPOStop request t
14、o mechanismStop requested: Lo 44P24/BUZBEEPOBeep outputActive: Hi 45P25/SI0PLL_CEOCE output to PLL 46P26/SO0PLL_DATAI/OData in/out with PLL 47P27/SCK0PLL_CLKOClock output to PLL 48P80/A0CD_SW3ISwitch detectionON : Hi 49P81/A1LO/EJOLoading/Eject controlLoading: Lo/Eject: Hi 50P82/A2MOSWOMotor outputL
15、oading: Hi/Eject: Lo 51P83/A3MECH_ DETIMechanism detectionON: Hi/OFF: Lo 52P84/A4PAN5VOPanel detectionOFF: Hi 53P85/A5L_CE/P_RSTOCE to LCD driver/Panel -com reset 54P86/A6L_INH/MC_REQOReset to LCD driver 34 KDC-X915/X815/PS9016R/PS9080RKDC-X915/X815/PS9016R/PS9080R No.Pin nameFunctionI/ODescriptionP
16、rocessing Operation 55P87/A7DIM_CONODIM control 56P40/AD0QUALIRDS receiving conditionGood: Hi 57P41/AD1R_DATAIRDS data input 58P42/AD2SRM_SUB-OSRM sub motor output 59P43/AD3SRM_SUB+OSRM sub motor output 60P44/AD4SRM_DETISRM mechanism detectionON: Lo/OFF: Hi 61P45/AD5SRM_SW2ISRM eject detection : Eje
17、ct 62P46/AD6FM_SDIFM SD inputStation detected: Hi Not detected: Lo 63P47/AD7NCOOpen 64P50/A8AFCONoise detection time constant switchingDuring reception: Hi During search: Lo 65P51/A9O 66P52/A10WIDEOK2I Wide outputActive: Hi 67P53/A11NARROWI/OK2I Narrow outputActive: Hi 68P54/A12AM+BOAM power supplyA
18、ctive: Hi 69P55/A13FM+BOFM power supplyActive: Hi 70P56/A14NCOOpen 71P57/A15NCOOpen 72Vss-GND 73P60/A16TYPE0IDestination type switch 74P61/A17TYPE1IDestination type switch 75P62/A18TYPE2IDestination type switch 76P63/A19ST_TYPE0IIC2 Var. 3 destination type 0Initial value: Lo 77P64/RDST_TYPE1IIC2 Var
19、. 3 destination type 1Initial value: Lo 78P65/WRNCOOpen 79P66/WAITPRE MUTE ROOpenActive: Lo 80P67/ASTBPRE MUTE LOOpenActive: Lo 81Vdd-Positive power supply 82P100/TI5/TO5NCOOpen 83P101/TI6/TO6SVROPower IC resetPower ON: Lo 84P102/TI7/TO7NCOOpen 85P103/TI8/TO8P_MUTEOPower IC mutingActive: Lo 86P30/TO
20、0ANT_CONOAntenna controlActive: Hi 87P31/TO1IC2_SCKOIC2, IC5, EEPROM clock line 88P32/TO2DIMMERIDimmer detectionActive: Lo 89P33/TI1P_CONOPower controlActive: Hi 90P34/TI2ACC_DETIACC detectionACC OFF: Hi 91P35/TI00REMOIRemote control input 92P36/TI01P_ONO-com peripheral power supplyActive: Hi 93P37B
21、U_DETIMomentary power down detectionMomentary power down: Hi 94TEST-TestGND 95P90IC2_SDAI/OIC2, IC5, EEPROM data line 96P91MUTEOMuting outputActive: Hi 97P92SW5O5V power supplyActive: Lo 98P93MS_CLOCD mechanism clock line 99P94MS_DAI/OCD mechanism data line 100P95ONC MICROCOMPUTERS DESCRIPTION Radio
22、Fans.CN 收音机爱 好者资料库 MICROCOMPUTERS DESCRIPTION System -com: UPD784217GC GTerminal description No.Pin nameFunctionI/ODescriptionProcessing Operation 1P120/RTP0CHCON1OChanger 1 controlActive: Hi 2P121/RTP1CH_MUTEIChanger muting inputMUTE Requested : Hi 3P122/RTP2REQHOHandshake request to changersActive
23、: Lo 4P123/RTP3ILL_ONOIllumination outputActive: Hi 5P124/RTP4NCOOpen 6P125/RTP5CD_SW2I12cm DISC detectionON: Lo 7P126/RTP6CD_SW1ILoading detectionON: Lo 8P127/RTP7NCOOpen 9VddVdd-Positive power supply 10X2X2-Main clock connection 11X1X1-Main clock connection 12VssVss-GND 13XT2XT2-Sub clock connecti
24、on 14XT1XT1-Sub clock connection 15RESETRESETIReset inputActive: Lo 16P00/INTP0CH_RSTOChanger reset outputActive: Lo 17P01/INTP1R_CLKIRDS clock input 18P02/INTP2/NMIREQCIHandshake request from changerActive: Lo 19P03/INTP3NCI/O 20P04/INTP4NCI/O 21P05/INTP5NCI/O 22P06/INTP6SC_REQIHandshake request fr
25、om panel -com 23AVddAVdd-A/D analog power supply 24AVref0AVref-A/D reference voltage input 25P10/AN10PHONEIPHONE detection terminal1V or less: PHONE 2.5V or more: NAVI MUTE 26P11/ANI1SRM_SW1ISRM position detectionOpen: Hi 27P12/ANI2NOISEIFM noise detectionAnalog input 28P13/ANI3SMETERIFM signal mete
26、r detectionAnalog input 29P14/ANI4IF_MODEIK2I IF selectorWide: Hi/Narrow: Lo 30P15/ANI5NCIGND 31P16/ANI6M_MUTE_RIMute request from mechanismMute requested: Lo 32P17/ANI7M_MUTE_LIMute request from mechanismMute requested: Lo 33AVssAVss-A/D GND 34P130/ANO0EXT_AMPOEXT_AMP control 35P131/ANO1M_RSTOReset
27、 output to mechanismReset: Lo 36AVref1-D/A reference voltage input 37P70/RxD2/SI2DATACIData line from changer 38P71/TxD2/SO2DATAHOData line to changer 39P72/ASCK2/SCK2CH_CLKI/OClock line from/to changer 40P20/RxD1/SI1L_DATAL/SC_DATAIData line from LCD driver 41P21/TxD1/SO1L_DATAS/MC_DATAI/OData line
28、 to LCD driver 42P22/ASCK1/SCK1L_CLK/MC_CLKI/OClock line to LCD driver 43P23/PCLM_STOPOStop request to mechanismStop requested: Lo 44P24/BUZBEEPOBeep outputActive: Hi 45P25/SI0PLL_CEOCE output to PLL 46P26/SO0PLL_DATAI/OData in/out with PLL 47P27/SCK0PLL_CLKOClock output to PLL 48P80/A0CD_SW3ISwitch
29、 detectionON : Hi 49P81/A1LO/EJOLoading/Eject controlLoading: Lo/Eject: Hi 50P82/A2MOSWOMotor outputLoading: Hi/Eject: Lo 51P83/A3MECH_ DETIMechanism detectionON: Hi/OFF: Lo 52P84/A4PAN5VOPanel detectionOFF: Hi 53P85/A5L_CE/P_RSTOCE to LCD driver/Panel -com reset 54P86/A6L_INH/MC_REQOReset to LCD dr
30、iver 34 KDC-X915/X815/PS9016R/PS9080RKDC-X915/X815/PS9016R/PS9080R No.Pin nameFunctionI/ODescriptionProcessing Operation 55P87/A7DIM_CONODIM control 56P40/AD0QUALIRDS receiving conditionGood: Hi 57P41/AD1R_DATAIRDS data input 58P42/AD2SRM_SUB-OSRM sub motor output 59P43/AD3SRM_SUB+OSRM sub motor out
31、put 60P44/AD4SRM_DETISRM mechanism detectionON: Lo/OFF: Hi 61P45/AD5SRM_SW2ISRM eject detection : Eject 62P46/AD6FM_SDIFM SD inputStation detected: Hi Not detected: Lo 63P47/AD7NCOOpen 64P50/A8AFCONoise detection time constant switchingDuring reception: Hi During search: Lo 65P51/A9O 66P52/A10WIDEOK
32、2I Wide outputActive: Hi 67P53/A11NARROWI/OK2I Narrow outputActive: Hi 68P54/A12AM+BOAM power supplyActive: Hi 69P55/A13FM+BOFM power supplyActive: Hi 70P56/A14NCOOpen 71P57/A15NCOOpen 72Vss-GND 73P60/A16TYPE0IDestination type switch 74P61/A17TYPE1IDestination type switch 75P62/A18TYPE2IDestination
33、type switch 76P63/A19ST_TYPE0IIC2 Var. 3 destination type 0Initial value: Lo 77P64/RDST_TYPE1IIC2 Var. 3 destination type 1Initial value: Lo 78P65/WRNCOOpen 79P66/WAITPRE MUTE ROOpenActive: Lo 80P67/ASTBPRE MUTE LOOpenActive: Lo 81Vdd-Positive power supply 82P100/TI5/TO5NCOOpen 83P101/TI6/TO6SVROPow
34、er IC resetPower ON: Lo 84P102/TI7/TO7NCOOpen 85P103/TI8/TO8P_MUTEOPower IC mutingActive: Lo 86P30/TO0ANT_CONOAntenna controlActive: Hi 87P31/TO1IC2_SCKOIC2, IC5, EEPROM clock line 88P32/TO2DIMMERIDimmer detectionActive: Lo 89P33/TI1P_CONOPower controlActive: Hi 90P34/TI2ACC_DETIACC detectionACC OFF
35、: Hi 91P35/TI00REMOIRemote control input 92P36/TI01P_ONO-com peripheral power supplyActive: Hi 93P37BU_DETIMomentary power down detectionMomentary power down: Hi 94TEST-TestGND 95P90IC2_SDAI/OIC2, IC5, EEPROM data line 96P91MUTEOMuting outputActive: Hi 97P92SW5O5V power supplyActive: Lo 98P93MS_CLOC
36、D mechanism clock line 99P94MS_DAI/OCD mechanism data line 100P95ONC MICROCOMPUTERS DESCRIPTION TEST MODE 1.Entering the test mode Reset the unit by pressing the FM key and the Preset 6 key at the same time. When the test mode is entered, all indicators light up. 2.Releasing the test mode Reset the
37、unit by pressing the Preset 6 key. Note: The unit cannot be reset by simply turning ACC off, turning power off, or turning power off for a brief moment. 3.Voltage adjustment on the FM S-meter (1) Enter the test mode. (2) While pressing the Preset 1 key, keep on pressing the Preset 6 key. (3) When th
38、e adjustment is made, ADJ OK is displayed. When adjustment cannot be made, ADJ NG is displayed. 4.Writing SD voltage for the AM (1) Enter the test mode. (2) While pressing the Preset 1 key, keep on pressing the Preset 6 key, which results in writing SD. 5.Forced switching of K2I Auto/Manual In tuner
39、-mode, keeping on pressing TI key, and the Auto and Manual modes can be swieched. The initial condition is manual modes, which is indicated by flashing DUAL dots. 6.Forced narrow/wide switchng of K2I In tuner-mode, when Preset 6 is pressed, forced narrow/ wide mode switching is made. The initial con
40、dition is in wide mode and the NEWS dot flashes. 7.CD receiver test mode specification By pressing the track-up key, the unit jumps to the following tracks: No. 9 No. 15 No. 10 No. 11 No. 12 No. 13 No. 14 No. 9 (Goes back to the first position.) When the track-down key is pressed, the unit jumps to
41、the previous track. 8.MD test mode specification After loading MD, the unit plays No. 7. Then, the unit jumps as follows each time it track-ups. No. 2 No. 13 No. 23 No. 30 No. 34 No. 7 (Goes back to the first position.) When the track-down key is pressed, the unit jumps to the previous track. 9.Tape
42、 test mode In the initial step, the blank skip is turned off. 10.Audio-related items The volume is -10dB (on display, it is 30). The loudness is off and CRSC is off regardless of functions. Buss/treble and balance/fader are to be adjusted by the up/down key to full-boost/fullcut and fullfront/fullre
43、ar respectively. The high-pass filter is adjusted by the up-key to throughput/100Hz/200Hz and, by the down-key, to 200Hz/100Hz/throughput. Other adjustments are the same as before. 11.Backup current measurement When reset in ACC-off condition (backup is on), the mute terminal goes off after 2 second
44、s instead of 15 seconds, when the ACC is tuned off in the test mode. (In this case, the panel/CD/C/MD mechanisms are not activated.) 12.Registering security code after changing E2PROM at the services (Only for type M. However, RDS models are excluded) (1) Put the unit into the test mode (Refer to 1.
45、 Above for how to enter the test mode.) (2) Press SRC key to put the unit into the tuner mode. (3) Press Audio key for one second and put the unit into the menu mode. (4) Press FM/AM key and then select SECURITY. (5) Press track up/down key for full 2 seconds. (6) Press Preset 1, Preset 2, Preset 3,
46、 and Preset 4 and then input codes. Example: Inputting 3510. Preset 1 key 4 times. Preset 2 key 6 times. Preset 3 key 2 times. Preset 4 key once. (7) Press DISP key for 3 seconds and confirm that APPROVED is displayed. (8) Release the test mode. (Refer to 2. Releasing the test mode above.) 13.Simpli
47、fied method for clearing the security code (Only for type K) (1) When code is requested, continue pressing VOL UP key for three seconds while pressing the DISP key. (. disappear.) (2) Input KCAR, using the remote controller (the same as the 98 Model) Press Tenkey 5 twice and then press track-up key.
48、 (Inputting K) Press Tenkey 2 three times and then press track-up key. (Inputting C) Press Tenkey 2 once and then press track-up key. (Inputting A) Press Tenkey 7 twice and then press track-up key. (Inputting R) (3) Then, the security is released and the unit goes into the Tuner Mode. 14.Writing MAS
49、K KEY on line (E2PROM in initial codition) (1) While pressing the FM key and Preset 6 key, press reset key to enter the test mode. (2) Press AUDIO key for full one second to put the unit into the menu mode. (3) Select the MASK KEY, using the FM key or AM key. (4)Press on the track up/down key to display TRANSMIT 1. (5) Point the MASK KEY to the light receptor and press it for 0.5 second or longer. (6) When TRANSMIT 2 is displayed, press MASK KEY for 0.5 second or longer. When this is conducted, the counter codes for the first time and the second time will not
免费区 
