Pioneer-VSXD711-avr-sm 电路图 维修手册.pdf

《Pioneer-VSXD711-avr-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Pioneer-VSXD711-avr-sm 电路图 维修手册.pdf（83页珍藏版）》请在收音机爱好者资料库上搜索。

1、ORDER NO. PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01,

2、 Singapore 159936 PIONEER CORPORATION 2002 ModelTypePower RequirementRemarks VSX-D711-KMVXJIAC230V VSX-D711-KMYXJIEWAC220-230V VSX-D711-KMYXJIGRAC220-230V VSX-D711-SMYXJIEWAC220-230V RRV2607 AUDIO/VIDEO MULTI-CHANNEL RECEIVER VSX-D711-K T ZZV APR. 2002 Printed in Japan VSX-D711-S THIS MANUAL IS APPL

3、ICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S). For details, refer to Important symbols for good services on page 3. DOWNUP ENTER INPUT SELECTOR MASTER VOLUME MULTI JOG R STANDBY STANDBY/ON PHONES Nm-, OFFON RadioFans.CN 收音机爱 好者资料库 VSX-D711-K, VSX-D711-S 2 SAFETY INFORMATION This service manual is int

4、ended for qualified service technicians; it is not meant for the casual do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair complex products such as those covered by this manual. Improperly performed repairs can adv

5、ersely affect the safety and reliability of the product and may void the warranty. If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so and refer the repair to a qualified service technician. WARNING This product contains lead in sol

6、der and certain electrical parts contain chemicals which are known to the state of California to cause cancer, birth defects or other reproductive harm. Health & Safety Code Section 25249.6 Proposition 65 NOTICE (FOR CANADIAN MODEL ONLY) Fuse symbols (fast operating fuse) and/or (slow operating fuse

7、) on PCB indicate that replacement parts must be of identical designation. REMARQUE (POUR MODLE CANADIEN SEULEMENT) Les symboles de fusible (fusible de type rapide) et/ou (fusible de type lent) sur CCI indiquent que les pices de remplacement doivent avoir la mme dsignation. ANY MEASUREMENTS NOT WITH

8、IN THE LIMITS OUTLINED ABOVE ARE INDICATIVE OF A POTENTIAL SHOCK HAZARD AND MUST BE CORRECTED BEFORE RETURN- ING THE APPLIANCE TO THE CUSTOMER. 2. PRODUCT SAFETY NOTICE Many electrical and mechanical parts in the appliance have special safety related characteristics. These are often not evident from

9、 visual inspection nor the protection afforded by them necessarily can be obtained by using replacement components rated for voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified in this Service Manual. Electrical components having such features are

10、identified by marking with a on the schematics and on the parts list in this Service Manual. The use of a substitute replacement component which does not have the same safety characteristics as the PIONEER recommended replacement one, shown in the parts list in this Service Manual, may create shock,

11、 fire, or other hazards. Product Safety is continuously under review and new instructions are issued from time to time. For the latest information, always consult the current PIONEER Service Manual. A subscription to, or additional copies of, PIONEER Service Manual may be obtained at a nominal charg

12、e from PIONEER. (FOR USA MODEL ONLY) 1. SAFETY PRECAUTIONS The following check should be performed for the continued protection of the customer and service technician. LEAKAGE CURRENT CHECK Measure leakage current to a known earth ground (water pipe, conduit, etc.) by connecting a leakage current te

13、ster such as Simpson Model 229-2 or equivalent between the earth ground and all exposed metal parts of the appliance (input/output terminals, screwheads, metal overlays, control shaft, etc.). Plug the AC line cord of the appliance directly into a 120V AC 60 Hz outlet and turn the AC power switch on.

14、 Any current measured must not exceed 0.5 mA. Device under test Leakage current tester Earth ground Reading should not be above 0.5 mA Also test with plug reversed (Using AC adapter plug as required) Test all exposed metal surfaces AC Leakage Test RadioFans.CN 收音机爱 好者资料库 VSX-D711-K, VSX-D711-S 3 Imp

15、ortant symbols for good services In this manual, the symbols shown-below indicate that adjustments, settings or cleaning should be made securely. When you find the procedures bearing any of the symbols, be sure to fulfill them: 2. Adjustments To keep the original performances of the product, optimum

16、 adjustments or specification confirmation is indispensable. In accordance with the procedures or instructions described in this manual, adjustments should be performed. 3. Cleaning For optical pickups, tape-deck heads, lenses and mirrors used in projection monitors, and other parts requiring cleani

17、ng, proper cleaning should be performed to restore their performances. 5. Lubricants, glues, and replacement parts Appropriately applying grease or glue can maintain the product performances. But improper lubrication or applying glue may lead to failures or troubles in the product. By following the

18、instructions in this manual, be sure to apply the prescribed grease or glue to proper portions by the appropriate amount.For replacement parts or tools, the prescribed ones should be used. 4. Shipping mode and shipping screws To protect the product from damages or failures that may be caused during

19、transit, the shipping mode should be set or the shipping screws should be installed before shipping out in accordance with this manual, if necessary. 1. Product safety You should conform to the regulations governing the product (safety, radio and noise, and other regulations), and should keep the sa

20、fety during servicing by following the safety instructions described in this manual. RadioFans.CN 收音机爱 好者资料库 VSX-D711-K, VSX-D711-S 4 SAFETY INFORMATION.2 1. SPECIFICATIONS.5 2. EXPLODED VIEWS AND PARTS LIST.6 2.1 PACKING.6 2.2 EXTERIOR . 8 2.3 FRONT PANEL.10 3. BLOCKDIAGRAM AND SCHEMATIC DIAGRAM.12

21、 3.1 BLOCK DIAGRAM.12 3.2 OVERALL WIRING CONNECTION DIAGRAM . 14 3.3 DD & INPUT ASSY(1/4).16 3.4 DD & INPUT ASSY(2/4).18 3.5 DD & INPUT ASSY(3/4).20 3.6 DD & INPUT ASSY(4/4).22 3.7 AMP & PRIMARY(1/2), TRANS2 and TRANS3 ASSYS.24 3.8 AMP & PRIMARY(2/2), REGULATOR, HASHIGETA B TO B , AMP INPUT and TRAN

22、S 1 ASSYS.26 3.9 DIGITAL IN ASSY.28 3.10 KAWA ASSY.29 3.11 VIDEO and 6CH IN ASSYS.30 3.12 S. VIDEO ASSY.31 3.13 FRONT, R. ENCODER and POWER SW ASSYS.32 3.14 FRONT VIDEO and H.P. ASSYS.34 3.15 TRANS4 and MECHA SW ASSYS.35 3.16 FM/AM TUNER MODULE . 36 4. PCB CONNECTION DIAGRAM.38 4.1 TRANS1, TRANS2, T

23、RANS3 and TRANS4 ASSYS.39 4.2 DD & INPUT ASSY.40 4.3 AMP & PRIMARY, AMP INPUT and MECHA SW ASSYS.44 4.4 REGULATOR, HASHIGETA and KAWA ASSYS.46 4.5 B TO B, DIGITAL IN, VIDEO and 6CH IN ASSYS.48 4.6 S. VIDEO and FRONT VIDEO ASSYS.50 4.7 FRONT, POWER SW, H.P. and R. ENCODER ASSYS.52 4.8 FM/AM TUNER MOD

24、ULE . 56 5. PCB PARTS LIST.57 6. ADJUSTMENT.63 7. GENERAL INFORMATION . 64 7.1 DIAGNOSIS.64 7.1.1 U-COM BLOCKDIAGRAM.64 7.1.2 POWER ON AND OFF SEQUENCE.65 7.1.3 PROTECTION CIRCUIT.67 7.2.2 PCB LOCATION . 68 7.2 PARTS.69 7.2.1 IC.69 7.2.2 DISPLAY.77 7.3 CLEANING . 78 8. PANEL FACILITIES.79 CONTENTS 5

25、 VSX-D711-K, VSX-D711-S Accessories Remote control unit (XXD3042) AM loop antenna (ATB7009) FM wire antenna (ADH7005) AA size IEC R6P Dry cell batteries (x2) Miscellaneous Power Requirements UK model . AC 230 V, 50/60 Hz European model. AC 220-230 V, 50/60 Hz Power Consumption VSX-D711 .250W In Stan

26、dby. 1 W Dimensions . 420 (W) x 158 (H) x 401 (D) mm .10 kg Furnished Parts AM loop antenna . 1 FM wire antenna . 1 Dry cell batteries (AA size IEC R6P). 2 Remote control. 1 Operating instructions . 1 Specifications and the design are subject to possible modifications without notice, due to improvem

27、ents. DTS ,DTS-ES Extended Surround and Neo:6 are trademarks of Digital Theater Systems, Inc. Manufactured under license from Dolby Laboratories. Dolby, Pro Logic and the double D symbol are trademarks of Dolby Laboratorories. Amplifier Section Continuous Power Output (STEREO mode) Front . 100 W per

28、 channel (DIN 1kHz, THD 1.0 %, 8 ) Continuous Power Output Front . 100 W per channel (1kHz, THD 1.0 %, 8 ) Center . 100 W (1kHz, THD 1.0 %, 8 ) Surround . 100 W per channel (1kHz, THD 1.0 %, 8 ) Above specifications are applicable when the power supply is 230V. Input (Sensitivity/Impedance) CD, VCR/

29、DVR, CD-R/TAPE/MD, DVD/LD, TV/SAT . 200 mV/47 k Frequency Response CD, VCR/DVR, CD-R/TAPE/MD, DVD/LD, TV/SAT . 5 Hz to 100,000 Hz dB Output (Level/Impedance) VCR/DVR REC, CD-R/TAPE/MD REC . 200 mV/2.2 k Tone Control BASS . 6 dB (100 Hz) TREBLE . 6 dB (10 kHz) LOUDNESS . +9 dB/+9 dB (100 Hz/10 kHz) S

30、ignal-to-Noise Ratio DIN (Continuous rated power output/50 mW) CD, VCR/DVR, CD-R/TAPE/MD,DVD/LD, TV/SAT .96 dB Video Section Input (Sensitivity/Impedance) VCR/DVR, DVD/LD, TV/SAT . 1 Vp-p/75 Output (Level/Impedance) VCR/DVR . 1 Vp-p/75 Frequency Response VCR/DVR, DVD/LD,TV/SAT MONITOR. 5 Hz to 7 MHz

31、 dB Signal-to-Noise Ratio .55 dB FM Tuner Section Frequency Range. 87.5 MHz to 108 MHz Usable Sensitivity.Mono:13.2 dBf, IHF (1.3 V/ 75 ) 50 dB Quieting Sensitivity . Mono: 20.2 dB Stereo: 38.6 dBf Signal-to-Noise Ratio . Mono: 73 dB (at 85 dBf) Stereo: 70 dB (at 85 dBf) Signal-to-Noise Ratio (DIN)

32、. Mono: 62 dB Stereo: 58 dB Distortion. Stereo: 0.5 % (1 kHz) Alternate Channel Selectivity . 60 dB (400 kHz) Stereo Separation . 40 dB (1 kHz) Frequency Response .30 Hz to 15 kHz (1 dB) Antenna Input (DIN) . 75 unbalanced AM Tuner Section Frequency Range.531 kHz to 1,602 kHz Sensitivity (IHF, Loop

33、antenna) .350 V/m Selectivity .25 dB Signal-to-Noise Ratio .50 dB Antenna. Loop antenna +0 3 +0 3 Weight (without package) 1. SPECIFICATIONS 6 VSX-D711-K, VSX-D711-S 2. EXPLODED VIEWS AND PARTS LIST Parts marked by NSP are generally unavailable because they are not in our Master Spare Parts List. Th

34、e mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. Screws adjacent to mark on product are used for disassembly. For the applying amount of lubricants or glue, follow the instruction

35、s in this manual. (In the case of no amount instructions, apply as you think it appropriate.) NOTES: 1 3 2 4 10 12 13 8 11 14 5 6 7 MYXJIEW Type Only 9 2.1 PACKING 7 VSX-D711-K, VSX-D711-S 1FM Wire AntennaADH7005 NSP2Warranty CardARY7022 3AM Loop AntennaATB7009 NSP4Dry Cell Batteries(AA/R6P)VEM-013 5Operating InstructionsXRE3059 (English/German) 6Operating InstructionsSee Contrast table (2) (French/I