Pioneer-XDJ700-mp-sm1 电路图 维修手册.pdf

《Pioneer-XDJ700-mp-sm1 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Pioneer-XDJ700-mp-sm1 电路图 维修手册.pdf（48页珍藏版）》请在收音机爱好者资料库上搜索。

1、ORDER NO. PIONEER CORPORATION 1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, Japan PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra

2、Road, #04-01, Singapore 159936 Pioneer DJ Corporation 2015 2015 Printed in Japan XDJ-700 RRV4637 MULTI PLAYER XDJ-700 THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S). THIS SERVICE MANUAL SHOULD BE USED TOGETHER WITH THE FOLLOWING MANUAL(S). ModelTypePower RequirementRemarks XDJ-700UX

3、JCBAC 100 V to 240 V XDJ-700SYXJAC 100 V to 240 V XDJ-700FLXJAC 100 V to 240 V XDJ-700AXJAC 100 V to 240 V ModelOrder No.Remarks XDJ-700RRV4638SCHEMATIC DIAGRAM, PCB CONNECTION DIAGRAM, PCB PARTS LIST K-MZV NOV. RadioFans.CN 收音机爱 好者资料库 2XDJ-700 1234 A B C D E F 1234 SAFETY INFORMATION WARNING This p

4、roduct may contain a chemical known to the State of California to cause cancer, or birth defects or other reproductive harm. Health it is not meant for the casual do-it- yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair

5、 complex products such as those covered by this manual. Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty. If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so and r

6、efer the repair to a qualified service technician. 1. SAFETY PRECAUTIONS The following check should be performed for the continued protection of the customer and service technician. LEAKAGE CURRENT CHECK Measure leakage current to a known earth ground (water pipe, conduit, etc.) by connecting a leak

7、age current tester such as Simpson Model 229-2 or equivalent between the earth ground and all exposed metal parts of the appliance (input/output terminals, screwheads, metal overlays, control shaft, etc.). Plug the AC line cord of the appliance directly into a 120 V AC 60 Hz outlet and turn the AC p

8、ower switch on. Any current measured must not exceed 0.5 mA. ANY MEASUREMENTS NOT WITHIN THE LIMITS OUTLINED ABOVE ARE INDICATIVE OF A POTENTIAL SHOCK HAZARD AND MUST BE CORRECTED BEFORE RETURNING THE APPLIANCE TO THE CUSTOMER. 2. PRODUCT SAFETY NOTICE Many electrical and mechanical parts in the app

9、liance have special safety related characteristics. These are often not evident from visual inspection nor the protection afforded by them necessarily can be obtained by using replacement components rated for voltage, wattage, etc. Replacement parts which have these special safety characteristics ar

10、e identified in this Service Manual. Electrical components having such features are identified by marking with a on the schematics and on the parts list in this Service Manual. The use of a substitute replacement component which does not have the same safety characteristics as the PIONEER recommende

11、d replacement one, shown in the parts list in this Service Manual, may create shock, fire, or other hazards. Product Safety is continuously under review and new instructions are issued from time to time. For the latest information, always consult the current PIONEER Service Manual. A subscription to

12、, or additional copies of, PIONEER Service Manual may be obtained at a nominal charge from PIONEER. Leakage current tester Reading should not be above 0.5 mA Device under test Test all exposed metal surfaces Also test with plug reversed (Using AC adapter plug as required) Earth ground AC Leakage Tes

13、t (FOR USA MODEL ONLY) RadioFans.CN 收音机爱 好者资料库 3XDJ-700 5678 5678 A B C D E F CONTENTS SAFETY INFORMATION.2 1. SERVICE PRECAUTIONS.3 1.1 NOTES ON SOLDERING.3 1.2 NOTES ON REPLACING PARTS.4 1.3 SERVICE NOTICE.4 2. SPECIFICATIONS.5 3. BASIC ITEMS FOR SERVICE .6 3.1 CHECK POINTS AFTER SERVICING .6 3.2

14、JIGS LIST.6 3.3 PCB LOCATIONS.7 4. BLOCK DIAGRAM .8 4.1 OVERALL WIRING DIAGRAM .8 4.2 SIGNAL BLOCK DIAGRAM.9 4.3 POWER SUPPLY BLOCK DIAGRAM.10 5. DIAGNOSIS .11 5.1 POWER ON SEQUENCE.11 5.2 TROUBLESHOOTING.12 5.3 CONNECTION CONFIRMATION WITH THE PC.20 6. SERVICE MODE.21 6.1 SERVICE MODE .21 6.2 ABOUT

15、 THE DEVICE.29 7. DISASSEMBLY .30 8. EACH SETTING AND ADJUSTMENT.38 8.1 NECESSARY ITEMS TO BE NOTED.38 8.2 FIRMWARE UPDATE / RECOVERY.38 8.3 WRITING THE SERIAL NUMBER OF THE UNIT.38 8.4 JOG DIAL ROTATION LOAD ADJUSTMENT.39 8.5 ITEMS FOR WHITCH USERS SETTING IS AVAILABLE.40 9. EXPLODED VIEWS AND PART

16、S LIST.41 9.1 PACKING SECTION.41 9.2 EXTERIOR SECTION .43 9.3 DISPLAY SECTION.45 9.4 JOG DIAL SECTION .47 1. SERVICE PRECAUTIONS 1.1 NOTES ON SOLDERING For environmental protection, lead-free solder is used on the printed circuit boards mounted in this unit. Be sure to use lead-free solder and a sol

17、dering iron that can meet specifications for use with lead-free solders for repairs accompanied by reworking of soldering. Do NOT use a soldering iron whose tip temperature cannot be controlled. RadioFans.CN 收音机爱 好者资料库 4XDJ-700 1234 A B C D E F 1234 1.2 NOTES ON REPLACING PARTS 1.3 SERVICE NOTICE Th

18、e part listed below is difficult to replace as a discrete component part. When the part listed in the table is defective, replace whole Assy. Assy Name MAIN AssyAuthentication CoprocessorH337S3959USON package (UltraSmallOutlineNon-lead) IC2 DDR2M14D51216322R5BG2KBGA packageIC11, 14 MAIN CPUR8A77240D

19、500BG2BGA packageIC8 DSPD810K013DZKB400BGA packageIC301 LCD Backlight Power ICBD81A04EFV-MIC with heat-padIC701 12 V3.3 V DC/DC ConverterBD9328EFJIC with heat-padIC1301, 1302 12 V1.2 V DC/DC ConverterBD9328EFJIC with heat-padIC1303 USBA Current Limit ICTPS2557DRBQFN, IC with heat-padIC1202 ETHER PHY

20、LAN8720A-CPQFN, IC with heat-padIC1203 LCD Power ICR1290K103AQFN, IC with heat-padIC702 Parts that is Difficult to Replace Ref No.FunctionPart No.Remarks About the Flash ROM (IC13) in the MAIN Assy Replacement of the Flash ROM (IC13) in the MAIN Assy is not possible during service, because writing o

21、f the MAC address on the production line is required. Therefore, the Flash ROM (IC13) is not supplied as a service part. If the Flash ROM is defective, replace the whole MAIN Assy. After replacing the the MAIN Assy, writing of the serial number of the unit is required. For details on how to write th

22、e serial number, see 8.3 WRITING THE SERIAL NUMBER OF THE UNIT. About backup of the UTILITY settings As this unit is provided with user-settable UTILITY settings (such as the Play mode setting,) it is recommended that you back up the settings before starting repair. The settings can be stored for ba

23、ckup in a USB memory device. For details on how to back up and restore data, see g How to Back Up and Restore the Settings in 8.5 ITEMS FOR WHICH USER SETTINGS ARE AVAILABLE . About discharging If the 29-pin flexible cable connecting CN2001 on the PNLB Assy and CN1103 on the MAIN Assy of the control

24、 panel section is disconnected, be sure to unplug the Power cord then wait 3 minutes or more before reconnecting the flexible cable. This is because the internal electrical charge remains in the power circuit for a while after the Power cord is unplugged. If the flexible cable is connected in such a

25、 state, L706 will be damaged. If the ICP is damaged, no buttons or LEDs of the unit will light and nothing will be displayed when the POWER switch is set to ON. Control panel Section Bottom view 29-pin flexible cableMAIN Assy PNLB Assy CN2001 CN1103 5XDJ-700 5678 5678 A B C D E F 2. SPECIFICATIONS A

26、C adapter Power. AC 100 V to 240 V, 50 Hz/60 Hz Rated current.0.6 A Rated output.DC 12 V, 2 A Power consumption (standby) .0.5 W General Main Unit Power consumption.DC 12 V, 1200 mA Main unit weight.2.0 kg (4.4 lb) (When not attached with the stand).1.7 kg (3.7 lb) External dimensions .238 mm (W) 10

27、6.3 mm (H) 307.8 mm (D) (9.3 in. (W) 4.1 in. (H) 12.1 in. (D) (When not attached with the stand) .238 mm (W) 78.8 mm (H) 307.8 mm (D) (9.3 in. (W) 3.1 in. (H) 12.1 in. (D) ) Tolerable operating temperature.+5 C to +35 C Tolerable operating humidity.5 % to 85 % (no condensation) Analog audio output (

28、AUDIO OUT L/R) Output terminals. RCA terminal Output Level .2.0 Vrms (1 kHz) Frequency response. 4 Hz to 20 kHz S/N ratio.115 dB Total harmonic distortion .0.003 % USB downstream section (USB) Port.Type A Power supply.5 V/1 A or less USB upstream section (USB) Port.Type B LAN (PRO DJ LINK) Rating.10

29、0Base-TX Main display Display type. Active matrix TFT liquid crystal display (LCD) Supported languages. 18 languages The specifications and design of this product are subject to change without notice. Accessories Power cord (UXJCB: XDG3052) (SYXJ: ADG1154) (FLXJ: ADG1154, ADG7097) (AXJ: ADG7079) Aud

30、io cable 1 (XDE3045) LAN cable 1 (DDE1141) AC adapter 1 (DWR1546) Operating Instructions (Quick Start Guide) 1 (UXJCB: DRH1313) (SYXJ: DRH1314) (FLXJ: DRH1315) (AXJ: DRH1316) 6XDJ-700 1234 A B C D E F 1234 3. BASIC ITEMS FOR SERVICE 3.1 CHECK POINTS AFTER SERVICING 3.2 JIGS LIST Items to be checked after servicing To keep the product quality after servicing, confirm recommended check points shown below. 1Confirm the firmware version on Service mode.The version of the firmware must be latest. Update firmware to the latest one, if it is not t