Philips-BDP-9600-Service-Manual(1) 电路图 维修手册.pdf

《Philips-BDP-9600-Service-Manual(1) 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Philips-BDP-9600-Service-Manual(1) 电路图 维修手册.pdf（45页珍藏版）》请在收音机爱好者资料库上搜索。

1、Published by RY-KM 1046 AVMPrinted in the Netherlands BDP9600/12/51/93/98 Subject to modi cationEN Blue-Ray Disc Player Contents PageContents Page Copyright 2010 Philips Consumer Electronics B.V. Eindhoven, The Netherlands. All rights reserved. No part of this publication may be reproduced, stored i

2、n a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips. Version 1.1 2 Technical Specification and Connection Facilities 3 Laser Beam Safety Precautions.3-1 4 Important Safety Precautions .4-1 to 4-2

3、 5 Safety Check After Servicing . 5-1 7 Standard Notes For Servicing,Lead Free Requirements when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6) 4.Release the flat pack-IC from the CBA using tweezers.

4、 (Fig. S-1-6) CAUTION: 1.The Flat Pack-IC shape may differ by models. Use an appropriate hot-air flat pack-IC desoldering machine, whose shape matches that of the Flat Pack-IC. 2.Do not supply hot air to the chip parts around the flat pack-IC for over 6 seconds because damage to the chip parts may o

5、ccur. Put masking tape around the flat pack-IC to protect other parts from damage. (Fig. S-1-2) Fig. S-1-1 Standard Notes for Servicing, Lead Free Requirements when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted).

6、(Fig. S-1-6) 4.Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6) With Iron Wire: 1.Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3) 2.Affix

7、the wire to a workbench or solid mounting point, as shown in Fig. S-1-5. 3.While heating the pins using a fine tip soldering iron or hot air blower, pull up the wire as the solder melts so as to lift the IC leads from the CBA contact pads as shown in Fig. S-1-5. 4.Bottom of the flat pack-IC is fixed

8、 with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6) 5.Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6) Note:When using a soldering iron, care must be taken to

9、 ensure that the flat pack-IC is not being held by glue. When the flat pack-IC is removed from the CBA, handle it gently because it may be damaged if force is applied. Hot-air Flat Pack-IC Desoldering Machine CBA Flat Pack-IC Tweezers Masking Tape Fig. S-1-2 Flat Pack-IC Desoldering Braid Soldering

10、Iron Fig. S-1-3 Fine Tip Soldering Iron Sharp Pin Fig. S-1-4 To Solid Mounting Point Soldering Iron Iron Wire or Hot Air Blower Fig. S-1-5 Fine Tip Soldering Iron CBA Flat Pack-IC Tweezers Fig. S-1-6 7-3 Standard Notes for Servicing, Lead Free Requirements & Handling Flat Pack IC 2. Installation 1.U

11、sing desoldering braid, remove the solder from the foil of each pin of the flat pack-IC on the CBA so you can install a replacement flat pack-IC more easily. 2.The “” mark on the flat pack-IC indicates pin 1. (See Fig. S-1-7.) Be sure this mark matches the 1 on the PCB when positioning for installat

12、ion. Then presolder the four corners of the flat pack-IC. (See Fig. S-1-8.) 3.Solder all pins of the flat pack-IC. Be sure that none of the pins have solder bridges. Instructions for Handling Semi- conductors Electrostatic breakdown of the semi-conductors may occur due to a potential difference caus

13、ed by electrostatic charge during unpacking or repair work. 1. Ground for Human Body Be sure to wear a grounding band (1 M ) that is properly grounded to remove any static electricity that may be charged on the body. 2. Ground for Workbench Be sure to place a conductive sheet or copper plate with pr

14、oper grounding (1 M ) on the workbench or other surface, where the semi-conductors are to be placed. Because the static electricity charge on clothing will not escape through the body grounding band, be careful to avoid contacting semi-conductors with your clothing. Example : Pin 1 of the Flat Pack-

15、IC is indicated by a mark. Fig. S-1-7 Presolder CBA Flat Pack-IC Fig. S-1-8 CBA Grounding Band Conductive Sheet or Copper Plate 1M 1M CBA Standard Notes for Servicing, Lead Free Requirements & Handling Flat Pack IC 7-4 Direction of Use 8-1 *The following excerpt of the DFU/QSG serves as an introduct

16、ion to the set. The Complete Direction for Use can be download in different languages from the internet site of Philips Customer care Center : Remote control a Turn on this player or switch to standby mode. When EasyLink is enabled, press and hold for at least three seconds to turn all connected HDM

17、I CEC compliant devices to standby. b Access the home menu of this player. cDISC/POP-UP BD: Access or exit the pop-up menu. DVD: Access or exit the disc menu. d/ Navigate through the menus. e/ Skip to the previous or next title, chapter, or track. a b c d i e f e q pg h o n j k j lm Product overview

18、 Main unit a ba Turn on this player or switch to standby mode. bDisplay panel cIR sensor Detect signals from the remote control. Always point the remote control at the IR sensor. dDisc compartment e Open or close the disc compartment . f Start or resume play. g Pause play. hjack Connect a USB device

19、. ehfcd g Direction of Use Remote Control 8-2 3Connect Make the following connections to use this player. Basic connections: Video Audio Power Optional connections: Route audio to other devices HDMI-compliant AV receiver/ampli er Multi-channel AV ampli er/receiver Digital AV ampli er/receiver Analog

20、 stereo system USB device Wired/Wireless network Note Refer to the type plate at the back or bottom of the product for identi cation and supply ratings. Before you make or change any connections, ensure that all the devices are disconnected from the power outlet. Connect video/audio cables Select th

21、e best video connection that theTV can support. Option 1:Connect to the HDMI jack (for a HDMI, DVI or HDCP-compliant TV). Option 2:Connect to the component video jacks (for a standard TV or Progressive Scan TV). Option 3:Connect to the composite video jack (for a standard TV). Option 1: Connect to t

22、he HDMI jack 1Connect an HDMI cable (not supplied) to: theHDMI jack on this player. the HDMI input jack on the TV. HDMI IN f Access options for the current activity or selection. g Return to a previous display menu. h/ Search backward or forward. i Stop play. Press and hold to open/close the disc co

23、mpartment. jColor buttons BD: Select tasks or options. kAlphanumeric buttons Select an item to play. Enter values. Enter letters via SMS style entry. lAUDIO Select an audio language or channel on a disc. mSUBTITLE Select a subtitle language on a disc. n Start or resume play. o Pause play. Move the p

24、aused picture forward frame by frame . pTOP MENU BD: Display the top menu. DVD: Display the title menu. qOK Con rm an entry or selection. Direction of Use 8-3 Option 3: Connect to the composite video jack 1Connect a composite video cable (not supplied) to: theVIDEOjack on this player. the VIDEO inpu

25、t jack on the TV. 2Connect the audio cables (not supplied) to: theAudio LINE OUT - L/Rjacks on this player. the AUDIO input jacks on the TV. Tip The video input jack on the TV might be labeled as A/V IN, VIDEO IN, COMPOSITE or BASEBAND. Route audio to other devices You can route the audio from this

26、player to other devices. Connect to an HDMI-compliantAV receiv 1Connect an HDMI cable (not supplied) to: theHDMI jack on this player. the HDMI jack input jack on the device. VIDEO IN AUDIO IN HDMI IN Tip If the TV has a DVI connector only, connect via an HDMI/DVI adaptor. Connect an audio cable for

27、sound output. If there is a blank TV screen under HDMI connection, on the remote control pressand then press “731” (numeric buttons) to recover picture display. If this player connects to a TV compatible with 1080p or 1080p/24Hz, Philips recommends HDMI category 2 cable, also known as High Speed HDM

28、I cable, for optimal video and audio output. To play the digital video images of a BD-video or DVD- video via an HDMI connection, it is necessary that both this player and the display device (or an AV receiver/ampl er) support a copyright protection system called HDCP (high- bandwidth digital conten

29、t protection system). This connection provides the best picture quality. Option 2: Connect to the component video jacks 1Connect the component video cables (not supplied) to: theY Pb/Cb Pr/Crjacks on this player. the COMPONENT VIDEO input jacks on the TV. 2Connect the audio cables (not supplied) to:

30、 theAudio LINE OUT-L/Rjacks on this player. the AUDIO input jacks on the TV. Tip The component video input jack on the TV might be labeled as Y Pb Pr or YUV. Pb Y Pr AUDIO IN Direction of Use 8-4 1Connect a coaxial cable (not supplied) to: theCOAXIAL jack on this player. the COAXIAL/DIGITAL input ja

31、ck on the device. Connect to optical jack 1Connect an optical cable (not supplied) to: theOPTICALjack on this player. the OPTICAL/DIGITAL input jack on the device. Connect an analogue stereo system 1Connect the audio cables (not supplied) to: theAudio LINE OUT-L/R jacks on this player. the AUDIO inp

32、ut jacks on the device. Connect a USB device 1Connect a USB device to the (USB) jack on the front panel of this player. Note Press, and select Browse USBin the menu to access the content and play theles. Connect a USB device only to the jack on this player. Philips does not guarantee compatibility w

33、ith all USB devices. OPTICAL AV IN Tip The HDMI connection provides the best audio quality. Connect to a multi-channelAV receiver/ 1Connect the 7.1-channel audio cables (not supplied) to: the7.1 CH AUDIO OUTPUTjacks on this player. the corresponding AUDIO input jacks on the device. Tip To connect 5.

34、1-channel AV receiver/ampli er, connect the 7.1-channel audio jacks except theSL/SRjacks. You can optimize the speaker output (see “Adjust settings” AudioSpeaker Setup). Connect to a digitalAreceiver Connect to coaxial jack 7.1 CH AUDIO INPUT COAXIAL Direction of Use 8-5 Connect a network With a wir

35、ed or wireless connection (see “Get started” “Set up a network”), you can connect this player to: the Internet (for software update/BD Live/Net TV service). or a home network (to access mediaes from a DLNA media server, e.g. PC). Note Internet access to Philips website for software update may not be

36、 allowed, depending on the router you use or the Internet Service Providers policy. Contact your Internet Service Provider for more information. Connect power Caution Risk of player damage! Ensure that the power supply voltage corresponds to the voltage printed on the back of the unit. Before connec

37、ting the AC power cord, ensure you have completed all other connections. Note The type plate is located on the back of the player. 1Connect the AC power cable to: this player. the wall socket. This player is ready to be set up for use. Cabinet Disassembly Instructions 1. Disassembly Flowchart This f

38、lowchart indicates the disassembly steps to gain access to item(s) to be serviced. When reassembling, follow the steps in reverse order. Bend, route, and dress the cables as they were originally. 2. Disassembly Method Note: (1) Identification (location) No. of parts in the figures (2) Name of the pa

39、rt (3) Figure Number for reference (4) Identification of parts to be removed, unhooked, unlocked, released, unplugged, unclamped, or desoldered. 0 x = Screw, CNxx/Jxx/CONxx = Connector D3.5X12BA is specification of screw. * = Unhook, Unlock, Release, Unplug, or Desolder e.g. 7(01) = seven Screws ID/

40、 Loc. No. Part Removal Fig. No. Remove/*Unhook/ Unlock/Release/ Unplug/Desolder Note 4 DVDDoor 3 Machine shield 2 TOP Cover 1 2 3 4 4 5 6 4(01) D3x6BMTT 3(02) D3x8BT 7(06) D3x4BMTT 1(04) D4x6KMTT,4x6KT 18(05) D3x8BT 10(07) D2.6x8BT D1 D3 D5 D6 D7 D8 D11 Fig. D1 Fig. D2 1 Aluminum decorative floor, M

41、achine bracket 5 Bly-RayDriver 7 Transformer 6 Top Loader Driver Top Loader Cover 8 Powersocketboard, Decoderboard, outputboard,Power board 9 USBTerminalboard 10 Frontpanel 12 TransparentPMMA,Tou- chpad,Powerbutton sp- port,LEDlens 13 USBdoor,DecorativeLenses, Touchpad Aluminum deco- rative floor, M

42、ac- hine bracket Machine shield Bly-RayLoader Driver 4(03) D3x8BT 2(08) D3x5BMTT Transformer Powersocket bo- ard,Decoderboa- rd,Output board Powerboard Touch Keyboard VFD displayboard 01 9-1 11Touch Key Board VFD Display Board 9-2 Fig. D3 Fig. D7 Fig. D4 Cabinet Disassembly Instructions Fig. D5 Fig.

43、 D8 02 04 05 06 05 05 03 Fig.D6 08 9-3 Cabinet Disassembly Instructions Fig. D10 Fig. D12 Fig. D13 Fig. D11 07 Fig. D9 No power Check the Power Cord is connected Check whether the Power Transfer Board has provided voltage output (AC220V) No sound Check whether the PowerBoard has provided voltage out

44、put Adjust the volume Use Oscillograph to checkVFD data cable if has normal nignal or not ,the check location is U201 pin No 5#(VFD DATA)、8#(CLK)and STB provide voltage No display Check the FUSE is ok or not? Check the power pcb “CON1” connection to display board cable normal No picture on HDMI conn

45、ection Check if the HDMI cable is usable Replace a new HDMI cable Check the connect cable is OK or NOT Check Digital output board(J2) & decoder board(xp8)between the flat connect wire is OK or NOT and Re-planted Check location CON1 in power board has normal voltage:+5v、 -27v、VF（-12V)、S5V(5V)、 and ha

46、s STB provide voltage Use Oscillograph to check jack (J300)pin No 15#(HDMI_SCL)、 16#（HDM_SDA）wave if normal check J300 cable pin No 1#、 3#、4#、6#、7#、9#、10# TX signal normal or no Check whether provide 18V voltage for Digital Output Board jack(J3) Check location U201 in display board pin No15#、37# has

47、 5V provide voltage,check 27# pin has -30v provide voltage Replace a new Power Transfer Board N Replace a new one N Replace a new Board N Replace a new one N Replace a new one N Check&replace the digital output board N Replace a new one N N N N Replace the decoder board Y Y Check the FUSE is ok or n

48、ot? Y Y Y Y Cant Loading Check the flat connect wire is OK or NOT and Re-planted Check&replace the Loader Replace a new one N Test decoder board jack (XP4)pin no.1#2# imp- edance 0ohm N Y Y Y Y Y Y Y Y Y Y Troubleshooting 10-110-1 Check a television change to HDMI mode NChange to HD- MI mode Y Y Che

49、ck&replace the transformer N Y Test the decoder board jack(xp8) pin no.22#(+12vA)、23#（-12V） has provided voltage Confirm decoder board jack(xp8) location pin no.16#(mute) low le- vel Y N Y Check related MUTE circuit decoder board use oscillograph to check decoder board jack(xp8)pin no.6#(MCLK)、 8#（BCK)data whether normal Y replace digital output board N replace decoder board Confirmed machine tray in and out action normal check decoder board