Sony-CDPCE335-cd-sm 电路图 维修手册.pdf

《Sony-CDPCE335-cd-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Sony-CDPCE335-cd-sm 电路图 维修手册.pdf（28页珍藏版）》请在收音机爱好者资料库上搜索。

1、CDP-C591/CE235/CE335 US Model CDP-C591/CE235/CE335 Canadian Model AEP Model UK Model E Model Australian Model CDP-CE235/CE335 SERVICE MANUAL COMPACT DISC PLAYER MICROFILM SPECIFICATIONS Model Name Using Similar MechanismNEW CD Mechanism TypeCDM27-5BD32A Base Unit TypeBU-5BD32A Optical Pick-up TypeKS

2、S-213BA/F-NP Compact Disc Player LaserSemiconductor laser ( = 780 nm) Emission duration: continuous Laser outputMax 44.6 W* * This output is the value measured at a distance of 200 mm from the objective lens surface on the Optical Pick-up block with 7 mm aperture. Frequency response2 Hz to 20 kHz 0.

3、5 dB Signal-to-noise ratio More than 102 dB Dynamic rangeMore than 98 dB Harmonic distortion Less than 0.0045% Output JackMaximumLoad typeoutputimpedance level LINE OUTPhono2VOver 10 k jacks(at 50 k) DIGITAL OUTOptical18 dBmWave length: (OPTICAL)output660 nm connector General Power requirements Wher

4、e purchasedPower requirements USA and Canada120V AC, 60 Hz Europe and some Asian countries220V 230V AC, 50/60 Hz Other countries110V 120V AC or 220V 240V AC, adjustable, 50/60 Hz Power consumption14 W Dimensions (approx.)430 120 385 mm (w/h/d)(17 4 3/4 15 1/4 in.) incl. projecting parts Mass (approx

5、.)5.4 kg (11 lbs 15 oz) Supplied accessories Audio cord (2 phono plugs2 phono plugs) (1) Remote commander (remote) (1) (CDP-CE335 only) R6 (size AA) batteries (2) (CDP-CE335 only) Design and specifications are subject to change without notice. Photo : CDP-CE235 RadioFans.CN 收音机爱 好者资料库 2 TABLE OF CON

6、TENTS SAFETY-RELATED COMPONENT WARNING! COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY

7、 SONY. ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT! LES COMPOSANTS IDENTIFS PAR UNE MARQUE ! SUR LES DIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONT CRITIQUES POUR LA SCURIT DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PISES SONY DONT LES NUMROS SONT DONNS DANS CE MANUEL OU DANS L

8、ES SUPPMENTS PUBLIS PAR SONY. This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior. CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

9、1.GENERAL5 2.DISASSEMBLY 2-1.Case, Bottom Plate and Front Panel 6 2-2.Back Panel and Disc Table 6 2-3.Optical Pick-up Block Assembly 7 2-4.Bracket (Gear) Assembly 7 3.TEST MODE8 4.ELECTRICAL BLOCK CHECKING9 5.DIAGRAMS 5-1.Circuit Boards Location 10 5-2.IC Block Diagrams 11 5-3.Printed Wiring Board B

10、D Section 12 5-4.Schematic Diagram BD Section 13 5-5.Printed Wiring Board Main Section 14 5-6.Schematic Diagram Main Section 15 5-7.Printed Wiring Board Display Section 16 5-8.Schematic Diagram Display Section 17 5-9IC Pin Function IC302 System Control (CXP82324-090Q) 18 6.EXPLODED VIEWS 6-1.Front P

11、anel and Case Section 19 6-2.Back Panel and Disc Table Section 20 6-3.Chassis Section 21 6-4.Base Unit Section (BU-5BD32A) 22 7.ELECTRICAL PARTS LIST. 23 RadioFans.CN 收音机爱 好者资料库 3 MODEL IDENTIFICATION BACK PANEL CDP-C591 US MODEL: 618-7 CDP-CE235 US MODEL: 618-0 Canadian MODEL: 618-1 AEP,North Europ

12、ean MODEL : 618-2 UK MODEL: 618-3 Australian MODEL: 618-4 E,Saudi Arabia MODEL: 618-5 Singapore MODEL: 618-6 CDP-CE335 US MODEL: 619-0 Canadian MODEL: 619-1 AEP,North European MODEL : 619-2 UK MODEL: 619-3 Australian MODEL: 619-4 E,Saudi Arabia MODEL: 619-5 Singapore MODEL: 619-6 SAFETY CHECK-OUT (U

13、S model only) After correcting the original service problem, perform the following safety checks before releasing the set to the customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE

14、The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microampers). Leakage current can be measured by any one of three methods. 1.A commercial leakage tester, such as the Simpson

15、229 or RCA WT-540A. Follow the manufacturers instructions to use these instruments. 2.A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3.Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit”

16、 indication is 0.75 V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2V AC range are suitable. (See Fig. A) NOTES ON HANDLING THE OPTICAL PICK-UP

17、 BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostatic breakdown because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic breakdown and also use the procedure

18、 in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical

19、 pick- up block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens. 4-987- To Exposed Metal Parts on Set 0.15F1.5k AC voltmeter (0.75V) Earth Ground Fig. A. Using an AC voltmeter to check AC leakage. RadioFans.CN 收音机爱 好者资料库 4 HOW TO OPEN THE

20、 DISC TRAY WHEN POWER SWITCH TURNS OFF NOTE FOR MAIN GEAR INSTALLATION INOUT Tray Insert a tapeing driver into the aperture of the unit bottom, and turn in the direction of arrow (to OUT direction.) * To close the disc tray, turn the driver in the reverse direction(to IN direction). 2 Set the cut-ou

21、t of the ENCODER to the right when viewed from the front view. 3 Install the MAIN GEAR while aligning the protrusion of the MAIN GEAR to the cut-off of the ENCODER. 6 Stopper washer (5) 5 Rotate the MAIN GEAR until the portion that has no gears, of the MAIN GEAR is aligned with the shaft of the GEAR

22、 (REV). Then insert the GEAR (REV). Projected portion SHAFT 1 Rotate the GEAR (U/D) to the arrow A direction. 4 Open the SET LEVER and LOCK LEVER in the direction of the arrow B, and push in the MAIN GEAR. Front view B B A 5 SECTION 1 GENERAL Identifying the Parts Front Panel 11/u POWER switch 2CONT

23、INUE button 3SHUFFLE button 4PROGRAM button 5REPEAT button 6DISC CHECK button 7DISC 1-5 button 8Display window 9” (play) button !P (pause) button !p (stop) button !EX-CHANGE button !DISC SKIP button !6 OPEN/CLOSE button !AMS knob !FADER button !MUSIC SCAN button !CLEAR button !CHECK button ) (forwar

24、d) button 0 (backward) button Disc tray PEAK SEARCH button EDIT/TIME FADE button TIME button 12 3 4 5 67890 !? !?!? !? !?!?!? ? ? !?!? 6 SECTION 2 DISASSEMBLY 2-2. BACK PANEL AND DISC TABLE Note : Follow the disassembly procedure in the numerical order given. 2-1. CASE, BOTTOM PLATE AND FRONT PANEL

25、5 Four screws (BVTP 3 10) 7 Bottom plate! Three screws (BVTP 3 10) 6 Three screws (BVTP 3 10) 2 Two screws (M3 8) 3 Two screws (BV3 8) 1 Two screws (M3 8) 0 Two screws (BVTT3 8) ! Front panel 4 Case 8 Flat type wire(35 core) (MAIN board, to CN402) 9 Flat type wire(9 core) (MAIN board, to CN402) 7 Sc

26、rew (BVTP 3 8) ! Screw (BVTP 3 8) 9 Screw (BVTP 3 8) 5 Screw (BVTP 3 8) 6 Bracket (guide B1) ! Bracket (guide B1) 0 Bracket (guide F1) 8 Bracket (guide F1) 4 Flat type wire(6 core) (MAIN board, to CN404) 1 Connector 3 Back panel ! Disc table(B) ! Disc table(A) 2 Five screws (BVTP 3 10) ! Screw (PTPW

27、H 3 12) 7 2-3. OPTICAL PICK-UP BLOCK ASSEMBLY 2-4. BRACKET (GEAR) ASSEMBLY Note : As for the installation of the main gear, refer to “Note for MAIN GEAR installation” on page 4. 5 Two screws (PTPWH 2.6 6) 4 Two screws (PTPWH 2.6 6) 7 Compression spring(BU) 1 Pull out the tray. (Refer to HOW TO OPEN

28、THE DISC TRAY WHEN POWER SWITCH TURNS OFF on page 4.) 6 Holder (BU) 8 Compression spring (BU) 9 Optical pick-up block assembly 2 Flat type wire(16 core) (BD board, to CN101) 3 Screw (PTPWH 3 12) 6 Rotary encoder 4 Gear (MAIN) 2 Gear (REV) 8 Gear (U/D) 0 Bracket (GEAR) assembly 3 Stopper washer(5) 1

29、Stopper washer(5) 7 Stopper washer(5) 5 Screws (BVTP 3 8) 9 Five screws (BVTP 3 8) 8 SECTION 3 TEST MODE 1 ADJ Mode When the main power is turned on while the ADJ terminal is set to LOW, the CDP-C591/CE235/335 enters the ADJ mode that enables to implement the servo related checks. The disk tray is n

30、ot loaded or rotated. The fifth program is automatically played back. The following items are valid even when the main power is turned on first and the ADJ terminal is then set to LOW. The high speed search cannot be performed. The focus servo gain is not decreased. CLV servo gain is not decreased.

31、GFS is ignored even if it is set to the LOW. Q data is ignored even if it cannot be read. Switching of the monitor terminal is possible. Every pressing of the FADER key advances the MONITOR terminal in the following order. RFCKnGFCnError rate When “3” of the remote controller is pressed, the trackin

32、g servo is turned off. When “8” of the remote controller is pressed, the tracking servo is turned on. * The servo related items cannot be checked in the CDP-C591/ CE235/335. 2 Key Check and Display Check Mode When the main power is turned on while the AFADJ terminal is set to LOW, the CDP-C591/CE235

33、/335 enters the key check and display check mode in which keys and displays can be checked. First, all display tubes turn on. When any key is pressed after display tubes are turned on, the number of the keys that have been pressed appear on the left and the key number appears on the right. (Pushing

34、the JOG key is counted as one of the keys.) However, the following keys are treated as the special keys that show the different operations. STOP: All display turn-on check PLAY: Grid check PAUSE : Segment check JOG: Calendar check When receiving a signal from remote controller, the display “ * ” app

35、ears. (Number of asterisks * changes depending on the pressed key. For example, * is 50 when the PLAY key is pressed.) 3 Default Shipment Mode When the main power is turned on while pressing the DISCSKIP and the PROGRAM keys, the CDP-C591/CE235/335 enters the default shipment mode in which the defau

36、lt settings when shipped from the factory are set. Move the DISC 1 to the front and stop the machine. When the message “NODISC” appears, it indicates that the mode has ended with success. 4 Aging Mode When the OPEN key is pressed while the DISC1 and the CHECK keys are being pressed with the main pow

37、er being turned ON, the CDP-C591/CE235/335 enters the aging mode in which aging is performed in the following sequence. Reads TOCA-1 Accesses the last programA-2 Plays the last program for 3 secondsPLAY display appears EX-CHANGEA-4 DISCSKIPA-5 CLOSEA-6 Accesses the first programA-7 Playback the firs

38、t programPLAY display appears OPENA-9 DISPSKIPA-A CLOSEA-0 When an error occurs during aging, the message “Err*” appears and the operation is stopped. The system does not accept any key operations during aging. 9 RF PLL Free-run Frequency Check Procedure : 1.Connect frequency counter to TP (PLCK) wi

39、th lead wire. 2.Turned Power switch on. 3.Put the disc (YEDS-18) in to play the number five track. Confirm that reading on frequency counter is 4.3218MHz. Adjustment Location : BD BOARD Conductor Side BD board TP (PLCK) frequency counter TP(VC) TP(RF) TP(TE) TP(TE1) CN102 TP(FE) TP(PLCK) TP(GND) TP(

40、FE1) TP(AGCCON) IC101 20 21 40 4160 61 80 1 Note :Clear RF signal waveform means that the shape “ ” can be clearly distinguished at the center of the waveform. E-F Balance (1 Track jump) Check Procedure : 1.Connect oscilloscope to TP (TE) and TP (VC). 2.Turned Power switch on. 3.Load a disc (YEDS-18

41、) and playback the number five track. 4.Press the ( button. (Becomes the 1 track jump mode.) 5.Confirm that the level B and A (DC voltage) on the oscilloscope waveform. Note : 1.CD Block is basically designed to operate without adjustment. Therefore, check each item in order given. 2.Use YEDS-18 dis

42、c (3-702-101-01) unless otherwise indicated. 3.Use an oscilloscope with more than 10M impedance. 4.Clean the object lens by an applicator with neutral detergent when the signal level is low than specified value with the following checks. S-Curve Check Procedure : 1.Connect oscilloscope to TP (FE). 2

43、.Connect between TP (FE1) and TP (VC) by lead wire. 3.Connect between TP (AGCCON) and TP (GND) by lead wire. 4.Turn Power switch on. 5.Load a disc (YEDS-18) and actuate the focus search. (In consequence of open and close the disc tray, actuate the focus search) 6.Confirm that the oscilloscope wavefo

44、rm (S-curve) is symmetrical between A and B. And confirm peak to peak level within 4 1 Vp-p. 7.After check, remove the lead wire connected in step 2 and 3. Note : Try to measure several times to make sure than the ratio of A : B or B : A is more than 10 : 7. Take sweep time as long as possible and l

45、ight up the brightness to obtain best waveform. RF Level Check Procedure : 1.Connect oscilloscope to TP (RF). 2.Connect between TP (AGCCON) and TP (GND) by lead wire. 3.Turned Power switch on. 4.Load a disc (YEDS-18) and playback. 5.Confirm that oscilloscope waveform is clear and check RF signal lev

46、el is correct or not. 6.After check, remove the lead wire connected in step 2. SECTION 4 ELECTRICAL BLOCK CHECKING BD board Oscilloscope TP(FE) TP(VC) symmetry S-curve waveform within 4 1Vp-p A B TP(RF) TP(VC) BD board oscilloscope RF signal waveform VOLT/DIV : 200mV TIME/DIV : 500ns level : 1.45 0.

47、3Vp-p TP(TE) TP(VC) BD board oscilloscope level=1.30.6Vp-p symmetry A (DC voltage) center of waveform B 0V 1 track jump waveform Specified level: 100=less than 22% B A CDP-C591/CE235/CE335 10 5-1. CIRCUIT BOARDS LOCATION SECTION 5 DIAGRAMS BD BOARD SENSOR BOARD MAIN BOARD DISPLAY BOARD KEY BOARD POW

48、ER SW BOARD LOADING MOTOR BOARD TABLE MOTOR BOARD THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this necessary note is printed in each block) Note on Schematic Diagram: All capacitors are in F unless otherwise noted. pF: F 50 WV or less are not indicated excep

49、t for electrolytics and tantalums. All resistors are in and 1/4 W or less unless otherwise specified. %: indicates tolerance. : internal component. C : panel designation. U : B+ Line. V : B Line. Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. Voltages are taken with a VOM (Input impedance 10 M). Voltage variations may be noted due to norm