《Philips-FWD-550-Service-Manual(1) 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Philips-FWD-550-Service-Manual(1) 电路图 维修手册.pdf（55页珍藏版）》请在收音机爱好者资料库上搜索。
1、CLASS 1 LASER PRODUCT Service ServiceService ServiceService FW-D550/21M Copyright 2003 Philips Consumer Electronics B.V. Eindhoven, The Netherlands All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic
2、, mechanical, photocopying, or otherwise without the prior permission of Philips. Published by SL- ET0350 Service Audio Printed in The Netherlands Subject to modification. GB 3140 785 32790 Mini System Version 1.0 TABLE OF CONTENTS Page Location of PC Boards.1- 2 Versions Variation fr Reparaturen si
3、nd Original- Ersatzteile zu verwenden. I Le norme di sicurezza esigono che lapparecchio venga rimesso nelle condizioni originali e che siano utilizzati i pezzi di ricambio identici a quelli specificati. After servicing and before returning set to customer perform a leakage current measurement test f
4、rom all exposed metal parts to earth ground to assure no shock hazard exist. The leakage current must not exceed 0.5mA. CLASS 1 LASER PRODUCT 3122 110 03420 GB Warning ! Invisible laser radiation when open. Avoid direct exposure to beam. SVarning ! Osynlig laserstrlning nr apparaten r ppnad och sprr
5、en r urkopplad. Betrakta ej strlen. SFVaroitus ! Avatussa laitteessa ja suojalukituksen ohitettaessa olet alttiina nkymttmlle laseristeilylle. l katso steeseen! DK Advarse ! Usynlig laserstrling ved bning nr sikkerhedsafbrydere er ude af funktion. Undg udsaettelse for strling. Connections Step 1: Pl
6、acing speakers Place the front left and right speakers at equal distances from the TV set and at an angle of approximately 45 degrees from the listening position. Notes: To avoid magnetic interference, do not position the front speakers too close to your TV set. Allow adequate ventilation around the
7、 DVD Mini Hi-Fi System. Step 2: Connecting speakers DIN OUT speaker (right) speaker (left) SPEAKERS 6 SUBWOOFER OUT Connect the speaker wires to the SPEAKERS (FRONT) terminals, right speaker to “R”and left speaker to “L”, coloured (marked) wire to “+” and black (unmarked) wire to “”. Fully insert th
8、e stripped portion of the speaker wire into the terminal as shown. Notes: For optimal sound performance, use the supplied speakers. Do not connect more than one speaker to any one pair of +/- speaker terminals. Do not connect speakers with an impedance lower than the speakers supplied. Please refer
9、to the SPECIFICATIONS section of this manual. IMPORTANT! The type plate is located on the rear of the system. To avoid overheating of the system, a safety circuit has been built in. Therefore, your system may switch to Standby mode automatically under extreme conditions. If this happens, let the sys
10、tem cool down before reusing it. Speakers Front Left (L) Front Right (R) Black Black White Red + Connections Step 3: Connecting TV set IMPORTANT! You only need to make one video connection from the following options, according to the capabilities of your TV system. S-Video or Component Video connect
11、ion provides higher picture quality. These options must be available on your TV set. Connect the system directly to the TV set. Using Video In jack (CVBS) Use the composite video cable (yellow) to connect the systems CVBS jack to the video input jack (or labeled as A/V In, Video In, Composite or Bas
12、eband) on the TV set. To listen to TV channels through this system, use the audio cables (white/red) to connect AUX/ TV IN (L/R) jacks to the corresponding AUDIO OUT jacks on the TV set. Deactivate Progressive Scan through System Menu.See page 31, Using the Setup Menu Improving the image for progres
13、sive scanvideo output setting. Y? Televisio? n? Y? AUX/ TV IN LINE OUT (CVBS) D? D?D?P? U?UU?(?(? IMPORTANT! If both S-Video and Component (Pr Pb Y) Video connections are used to connect to your TV set, the Video signal will automatically switch to S-Video when you power up the system. To set theVID
14、EO OUT (put) toPr PbY,see page 31, Using the Setup Menu Setting thevideo out. Using component Video In jack (Pr Pb Y) Use the component video cables (red/blue/ green) to connect the systems Pr Pb Y jacks to the corresponding Component video input jacks (or labeled as Pr/Cr Pb/Cb Y or YUV) on the TV
15、set. To listen to TV channels through this system, use the audio cables (white/red) to connect AUX/ TV IN (L/R) jacks to the corresponding AUDIO OUT jacks on the TV set. If you are using a Progressive Scan TV set (TV must indicate Progressive Scan or ProScan capability),activate the PROGRESSIVE SCAN
16、 function through SYSTEM MENU. 1- 7 Connections AUDIO IN R L VIDEO IN TO TVINT IN CH3 CH4 RF coaxial cable to TV Back of RF Modulator (example only) Antenna or Cable TV signal LINE OUT (CVBS) D DDP UUU( IMPORTANT! If your TV set only has a single Antenna In jack (or labeled as 75 ohm or RF In), you
17、will need a RF modulator in order to view the DVD playback via TV. See your electronics retailer or contact Philips for details on RF modulator availability and operations. Using an accessory RF modulator Use the composite cable (yellow) to connect the systems CVBS jack to the video input jack on th
18、e RF modulator. Use the RF coaxial cable (not supplied) to connect the RF modulator to your TVs RF jack. Deactivate Progressive Scan through System Menu.See page 31, Using the Setup Menu Improving the image for progressive scanvideo output setting. Y Television Y AUX/ TV IN LINE OUT (CVBS) D DDP UUU
19、( IMPORTANT! If the picture is distorted, check the Video Output setting. Make sure it is set to S-Video. Using the Setup Menu Setting the video out. Using S-Video In jack Use the S-Video cable (not supplied) to connect the systems S-VIDEO OUT jack to the S- Video input jack (or labeled as Y/C or S-
20、VHS) on the TV set. To listen to TV channels through this system, use the audio cables (white/red) to connect AUX/ TV IN (L/R) jacks to the corresponding AUDIO OUT jacks on the TV set. Deactivate Progressive Scan through System Menu.See page 31, Using the Setup Menu Improving the image for progressi
21、ve scanvideo output setting. Connections Step 4: Connecting FM/AM antennas DIN OU? T? AM ? ANTENNA? FM ? ANTENNA? FM antenna AM antenna fix the claw into the slot Connect the supplied AM loop antenna to the AM jack. Place the AM loop antenna on a shelf or attach it to a stand or wall. Connect the su
22、pplied FM antenna to the FM jack. Extend the FM antenna and fix its end to the wall. For better FM stereo reception, connect an outdoor FM antenna to the FM ANTENNA terminal. AM ? ANTENNA? FM ? ANTENNA? Notes: Adjust the position of the antennas for optimal reception. Position the antennas as far as
23、 possible from your TV set, VCR or other radiation sources to prevent unwanted interference. Step 5: Connecting the power cord AC MAINS AUDIO OUT Pr/Cr Pb/Cb Y S-VIDEO IN VIDEO IN COMPONENT VIDEO IN Power Outlet DIN OU? T? SUBWOOFER OUT After everything is connected properly, plug in the AC power co
24、rd to the power outlet. Never make or change any connection with the power switched on. On the DVD Mini Hi-Fi System “AUTO INSTALL-PRESS PLAY” may appear on the display panel. Press 2; on the front panel to search and store all available radio stations or press 9 to exit (See page 35, Tuner Operatio
25、ns- Presetting radio stations). If your system is equipped with a Voltage Selector, set the VOLTAGE SELECTOR to the local power line voltage. VOLTAG? E? NOT FOR ALL? ? VERSION? S? SELECTO? R? 110V? -? 127V? 220V? -? 240V? 1- 8 Connections Connecting a VCR or cable/satellite box AUDIO OUT Pr/Cr Pb/Cb
26、 Y S-VIDEO IN VIDEO IN COMPONENT VIDEO IN ANT IN TO TV VCR or Cable/Satellite Box 2 4 1 3 3 AUX/ TV IN LINE OUT (CVBS) D DDP UUU( Viewing and listening to playback 1 Connect the VCR or Cable/Satellite Box to the TV system as shown. 2 Connect the systems AUX/TV IN (R/L) jacks to the AUDIO OUT jacks o
27、n the VCR or Cable/ Satellite box. Before starting operation, press AUX/TV on the remote control to select “AUX” in order to activate the input source. Using the VCR for recording DVDs Some DVDs are copy-protected. You cannot record or dub protected discs using a VCR. 3 Connect the systems CVBS jack
28、 to the VIDEO IN jack on the VCR. 4 Connect the systems LINE OUT (R/L) jacks to the AUDIO IN jacks on the VCR. This will allow you to make analog stereo (two channel, right and left) recording. To view DVD playback while recording You must connect the system to your TV system using the S-VIDEO (as s
29、hown above) or the Component (Pr Pb Y) video connection. Connecting digital audio equipment DIGIT AL OUT AUX/ TV IN LINE OUT (CVBS) D DDP UUU( Recording (digital) Connect the systems DIGITAL OUT jack to the DIGITAL IN jack on a digital recording device (DTS-Digital Theater System compatible, with a
30、Dolby Digital decoder, for example). Before operation, set the DIGITAL OUTPUT according to the audio connection. (See page 31, Using the Setup Menu Setting the digital output). 1- 9 PREV / PRESET / NEXT O P (TITLE / +) for DISC .to select previous/next title, chapter and track during playback. for T
31、UNER .to select a preset radio station. for CLOCK .(on the system only) to set the minute. 24; to connect headphones. 25SUBTITLE to select the preferred language for subtitle. LANGUAGE to select the preferred language for audio recorded. 27PROGRAM for DISC .to programme disc tracks. for TUNER .to pr
32、ogramme preset radio stations. DISPLAY to view the time, title or chapter information. CLOCK to view the clock, set the clock. TIMER to set the timer. Functional OverviewFunctional Overview Controls on the system 1 ECO POWER to switch the system on or to Eco Power Standby mode. 2 STANDBY ON2 to swit
33、ch the system on or to Standby mode. 3 DISPLAY SCREEN to view the current status of the system. 4 DISC TRAYS 5 DISC CHANGE to change disc(s). 6 DISC 1 / DISC 2 / DISC 3 to select a disc tray for playback. 7 OPENCLOSE to open or close the disc tray. 8 INTERACTIVE VU METER to show the VU (volume unit)
34、 meter in music or volume mode depending on the display mode selected. 9 SENSOR point the remote control towards this sensor. 0 VOLUME to increase or decrease the volume. ! Tape Deck Operation AUTO REPLAY to select continuous playback in either AUTO PLAY or ONCE mode only. DUBBING to dub a tape. REC
35、 to start recording on tape deck 2. VOCAL to fade out the original vocal from Karaoke or to switch between mono or stereo mode during audio disc playback. # JOG CONTROL to select the desired sound effect for the selected sound feature. $ KEY CONTROL to change the tone level to suit your vocal range.
36、 I .to decrease the key tone level. .to restore the key tone level to original setting. i .to increase the key tone level. % ECHO to adjust the echo level for karaoke after inserting the microphone. SOUND to activate or deactivate the surround sound effect. to start or interrupt disc playback. 7 STO
37、P 9 to stop playing the disc. 8 SURROUND to select multichannel surround (Dolby Digital, DTS and VSS) or stereo sound effect. 9 SOUND to select various sound effect: CONCERT, DRAMA, ACTION,SCI-FI, CLASSIC, JAZZ, ROCK or DIGITAL, MAX ON, MAX OFF. 0 MODE to select the REPEAT or SHUFFLE function. ! REP
38、EAT A-B to repeat a specific section on a disc. POWER 2 to switch to standby mode. # Numeric Keypad (0-9) to enter a track/title number of the disc. to enter a number of preset radio stations. $ VOL +/- adjust the volume level. % OK to exit or confirm the selection. RESUME to continue disc playback
39、after interruption. , 4, ). CAUTION! Remove batteries if they are exhausted or will not be used for a long time. Do not use old and new or different types of batteries in combination. Batteries contain chemical substances, so they should be disposed of properly. Step 2: Setting the clock The clock c
40、an be set in either 12-hour or 24- hour mode (“PM 00:00”or “00:00” for example). 1Go into Standby mode. If you have not set the clock,“-:-” will display until you set the clock. 2Press CLOCK and “00:00”blinks on the display. The current time is flashing on the display. If you have not set the clock,
41、 “-:-” will appear on the display. 3Press w or on the system to set the hours. 4Press 5 or 6 on the system to set the minutes. 5Press CLOCK to confirm your setting, and then go into standby mode. The system will store the setting automatically. The time setting becomes effective. To exit the setting
42、 without storing Press 9 on the system to exit. “CANCEL”will appear on the display. Press ECO POWER to exit setting mode and go into ECO POWER mode. You can also press DISC,DISC13,DISC CHANGE, OPEN/CLOSE to exit setting mode and go into disc mode. The system will also exit setting mode and go to tun
43、er,AUX, tape mode when you press the corresponding source button. Viewing the clock in any source mode Press DISPLAY on the system to toggle between 12-hour and 24-hour modes. The time will be displayed for a few seconds. Notes: The clock will be cancelled when the power cord is disconnected or if a
44、 power failure occurs. During clock setting, if no button is pressed within 30 seconds, the system will exit the setting mode and go into standby mode. TAPE 1/2 1- 12 Preparations Step 3: Setting the TV set IMPORTANT! Make sure you have completed all the necessary connections. (See page 11-12, Conne
45、ctions ConnectingTV set) 1Press DISC (DISC 123) on the front panel (or press DISC on the remote control). 2Turn on the TV set and set to the correct Video- In channel. You should see the blue Philips DVD background screen on the TV set. You may go to channel 1 on your TV set, then press the channel
46、down button repeatedly until you see the Video In channel. Or, you can use the TV remote control to select different video modes. Or, set TV to channel 3 or 4 if you are using an RF modulator. Selecting the color system that matches your TV set This DVD Mini Hi-Fi System is compatible with both NTSC
47、 and PAL. For the playback of a DVD disc on this DVD Mini Hi-Fi System, the color systems of the DVD, TV set and DVD Mini Hi-Fi System should match. 1In disc mode, stop playback and press SYSTEM MENU. 2Select icon and press 4. 3Press 1 / 2 / 3 / 4 keys on the remote control to toggle through the fun
48、ctions and select your preferred option. Move to and press 2. Move to “TV System” and press 2. AUTO Select this if the connected TV set is compatible with both NTSC and PAL (multi system). The output format will be consistent with the video signal of the disc. NTSC Select this if the connected TV se
49、t is NTSC system. It will change the video signal of a PAL video disc and output to NTSC system. PAL Select this if the connected TV set is PAL system. It will change the video signal of an NTSC disc and output to PAL format. 4Select an item and press OK. To remove the menu Press SYSTEM MENU. P-SCAN SET TO NTSC NTSC PAL 1 2,3 4 Pr
免费区 
