Sony-STRDA9000ES-rec-sm 电路图 维修手册.pdf

《Sony-STRDA9000ES-rec-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Sony-STRDA9000ES-rec-sm 电路图 维修手册.pdf（202页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL FM STEREO FM/AM RECEIVER SPECIFICATIONS STR-DA9000ES Ver 1.2 2004.09 9-961-292-03Sony Corporation 2004I05-1Audio Group 2004.09Published by Sony Engineering Corporation US Model Canadian Model Continued on next page This receiver incorporates Dolby* Digital and Pro Logic Surround and t

2、he DTS* Digital Surround System. * Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories. *“DTS”, “DTS-ES Extended Surround”, and “Neo:6” are trademarks of Digital Theater Systems, Inc. AUDIO POWER SPECIFICATIONS POWER O

3、UTPUT AND TOTAL HARMONIC DISTORTION: (Models of area code US only) With 8 ohm loads, both channels driven, from 20 20,000 Hz; rated 170 watts per channel minimum RMS power, with no more than 0.09% total harmonic distortion from 250 milliwatts to rated output. Amplifier section POWER OUTPUT Rated Pow

4、er Output at Stereo Mode (8 ohms, 20 Hz 20 kHz, THD 0.15%) 200 W + 200 W (4 ohms, 20 Hz 20 kHz, THD 0.15%) 220 W + 220 W Reference Power Output (8 ohms, 1 kHz, THD 0.09%) FRONT1): 200 W + 200 W CENTER1): 200 W SURR1): 200 W + 200 W SURR BACK1): 200 W + 200 W (4 ohms, 1 kHz, THD 0.09%) FRONT1): 220 W

5、 + 220 W CENTER1): 220 W SURR1): 220 W + 220 W SURR BACK1): 220 W + 220 W 1) Depending on the sound field settings and the source, there may be no sound output. Frequency response Inputs (Analog) 2) Input shorted and sealed at VOL MAX. 3) Weighted network + 20 kHz LPF, input level. Inputs (Digital)

6、Outputs EQUALIZER PHONORIAA equalization curve 0.5 dB Power Amp Block10 Hz 50 kHz 3 dB (8 ohms) PHONOSensitivity: 3.5 mV Impedance: 50 kilohms S/N2): 90 dB (A, 40 mV3) CD/SACD, TAPE, MD/DAT, DVD, LD, TV/SAT, VIDEO 1, 2, 3, 4, 5 Sensitivity: 170 mV Impedance: 50 kilohms S/N2): 100 dB (A, 2 V3) CD/SAC

7、D, DVD, LD, VIDEO 1, TV/SAT (Coaxial) Impedance: 75 ohms S/N: 100 dB (A Network, 20 kHz LPF) CD/SACD, DVD, LD, TV/SAT, MD/DAT, VIDEO1, 3 (Optical) S/N: 100 dB (A Network, 20 kHz LPF) TAPE, MD/DAT (REC OUT), VIDEO 1, 2, 3 (AUDIO OUT) Voltage: 170 mV Impedance: 2.2 kilohms FRONT L/R, CENTER, SURROUND

8、L/R, SURROUND BACK L/R, SUB WOOFER Voltage: 2 V Impedance: 220 ohms Gain levels10 dB, 1 dB step RadioFans.CN 收音机爱 好者资料库 2 STR-DA9000ES SAFETY-RELATED COMPONENT WARNING! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPE

9、RATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB- LISHED BY SONY. 4) You can change the AM tuning scale to 9 kHz or 10 kHz. After tuning in any AM station, turn off the receiver. While holding down PRESET TUNING + or TUNING +, p

10、ress ?/1. All preset stations will be erased when you change the tuning scale. To reset the scale to 10 kHz (or 9 kHz), repeat the procedure. Video section Inputs/Outputs Video:1 Vp-p, 75 ohms S-video:Y: 1 Vp-p, 75 ohms C: 0.286 Vp-p, 75 ohms COMPONENT VIDEO:Y: 1 Vp-p, 75 ohms PB/CB/B-Y: 0.7 Vp-p, 7

11、5 ohms PR/CR/R-Y: 0.7 Vp-p, 75 ohms i.LINK section Pin4 pins Transmission speedS200 (Maximum data transmission speed 200 Mbps) Transmission protocolA/M transmission protocol Format (input)Super Audio CD* (DSD PLAIN) 2 channel linear PCM (IEC- 60958-3) Sampling frequency: 44.1 kHz * Conforms to the c

12、opy protection technology of DTLA (Revision 1.2). General Power requirements120 V AC, 60 Hz Power consumption600 W Power consumption (during standby mode) 1 W AC outlets1 switched, 120 W/1A MAX Dimensions430 238 480 mm including projecting parts and controls Mass (Approx.)28.5 kg Supplied accessorie

13、s AC power coad (1) Easy Setup Guide (1) FM wire antenna (1) AM loop antenna (1) Remote commander RM-TP2 (1) Operating Instructions for RM-TP2 (1) AC adapter AC-96NP (1 for RM-TP2) RMB-TP1 (1 for RM-TP2) Remote commander RM-US106 (1) Operating Instructions for RM-US106 (1) R6 (size-AA) batteries (2)

14、 Design and specifications are subject to change without notice. FM tuner section Tuning range87.5 - 108.0 MHz AntennaFM wire antenna Antenna terminals75 ohms, unbalanced Sensitivity Mono:18.3 dBf, 2.2 V/75 ohms Stereo:38.3 dBf, 22.5 V/75 ohms Useable sensitivity11 76 dB 70 dB .2 dBf, 1 V/75 ohms S/

15、N Mono: Stereo: Harmonic distortion at 1 kHz Mono:0.3% Stereo:0.5% Separation45 dB at 1 kHz Frequency response30 Hz 15 kHz, +0.5/2 dB Selectivity60 dB at 400 kHz AM tuner section Tuning range530 1,710 kHz4) (With 10-kHz tuning scale) 531 1,710 kHz4) (With 9-kHz tuning scale) AntennaLoop antenna Usab

16、le sensitivity50 dB/m (at 1,000 kHz or 999 kHz) S/N54 dB (at 50 mV/m) Harmonic distortion0.5% (50 mV/m, 400 Hz) Selectivity At 9 kHz:35 dB At 10 kHz:40 dB ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT! LES COMPOSANTS IDENTIFIS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SO

17、NT CRITIQUES POUR LA SCURIT DE FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS QUE PAR DES PICES SONY DONT LES NUMROS SONT DONNS DANS CE MANUEL OU DANS LES SUPPLMENTS PUBLIS PAR SONY. RadioFans.CN 收音机爱 好者资料库 3 STR-DA9000ES Notes on chip component replacement Never reuse a disconnected chip component.

18、Notice that the minus side of a tantalum capacitor may be dam- aged by heat. Fig. A.Using an AC voltmeter to check AC leakage. 1.5 k0.15 F AC voltmeter (0.75 V) To Exposed Metal Parts on Set Earth Ground SAFETY CHECK-OUT After correcting the original service problem, perform the follow- ing safety c

19、heck before releasing the set to the customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE TEST The AC leakage from any exposed metal part to earth ground and from all exposed metal p

20、arts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes.). Leakage current can be measured by any one of three methods. 1.A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers instructions to use these instruments. 2

21、.A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3.Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indication is 0.75 V, so analog meters must have an accurate low-voltage scale. The

22、Simpson 250 and Sanwa SH-63Trd are examples of a pas- sive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suitable. (See Fig. A) UNLEADED SOLDER Boards requiring use of unleaded solder are printed with the lead- free mark (LF) indicating the solder

23、 contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size) : LEAD FREE MARK Unleaded solder has the following characteristics. Unleaded solder melts at a temperature about 40 C higher than ordinary solder. Ordinary soldering ir

24、ons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350 C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! Strong vis

25、cosity Unleaded solder is more viscou-s (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges oc- cur such as on IC pins, etc. Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. TABLE OF CO

26、NTENTS 1.SERVICING NOTES.5 2.GENERAL Location of Controls .9 3.DISASSEMBLY 3-1.Disassembly Flow . 12 3-2.Case (Top)/(Side-L)/(Side-R) . 13 3-3.Bracket (J)/(P-B) . 13 3-4.AMP Board Block. 14 3-5.Tuner, COMPONENT/TRIGGER/DVI Board Block . 14 3-6.S-VIDEO/VIDEO Board Block . 15 3-7.SUB Board, PREOUT Boa

27、rd, MAIN Board. 15 3-8.I. LINK Board, DIGITAL Board . 16 3-9.MOTHER Board Section . 16 3-10. MOTHER Board . 17 4.TEST MODE. 18 5.ELECTRICAL ADJUSTMENTS. 21 6.DIAGRAMS 6-1.Block Diagram AUDIO INPUT Section . 23 6-2.Block Diagram A/D CONVERTER Section . 24 6-3.Block Diagram DIGITAL INPUT, TUNER Sectio

28、n . 25 6-4.Block Diagram I. LINK Section . 26 6-5.Block Diagram DSP Section . 27 6-6.Block Diagram DIGITAL AUDIO Section . 28 6-7.Block Diagram AUDIO OUTPUT Section . 29 6-8.Block Diagram POWER AMP Section . 30 6-9.Block Diagram VIDEO INPUT/OUT Section . 31 6-10. Block Diagram COMPONENT VIDEO Sectio

29、n . 32 6-11. Block Diagram DVI, DISPLAY/CONTROL Section . 33 6-12. Block Diagram POWER SUPPLY Section . 34 6-13. Note for Printed Wiring Boards and Schematic Diagrams . 35 6-14. Printed Wiring Board DIGITAL Board (Component Side) . 36 6-15. Printed Wiring Board DIGITAL Board (Conductor Side) . 37 6-

30、16. Schematic Diagram DIGITAL Board (1/11) . 38 6-17. Schematic Diagram DIGITAL Board (2/11) . 39 6-18. Schematic Diagram DIGITAL Board (3/11) . 40 6-19. Schematic Diagram DIGITAL Board (4/11) . 41 6-20. Schematic Diagram DIGITAL Board (5/11) . 42 6-21. Schematic Diagram DIGITAL Board (6/11) . 43 6-

31、22. Schematic Diagram DIGITAL Board (7/11) . 44 6-23. Schematic Diagram DIGITAL Board (8/11) . 45 6-24. Schematic Diagram DIGITAL Board (9/11) . 46 6-25. Schematic Diagram DIGITAL Board (10/11) . 47 6-26. Schematic Diagram DIGITAL Board (11/11) . 48 6-27. Schematic Diagram MAIN Board (1/3) . 49 6-28

32、. Schematic Diagram MAIN Board (2/3) . 50 6-29. Schematic Diagram MAIN Board (3/3) . 51 6-30. Printed Wiring Board MAIN Board (Component Side) . 52 6-31. Printed Wiring Board MAIN Board (Conductor Side) . 53 6-32. Printed Wiring Board SUB Board (Component Side) . 54 6-33. Printed Wiring Board SUB Bo

33、ard (Conductor Side) . 55 RadioFans.CN 收音机爱 好者资料库 4 STR-DA9000ES 7.EXPLODED VIEWS 7-1.Case Section .146 7-2.Disp Board Section .147 7-3.Volume Section .148 7-4.Panel (Door) Section.149 7-5.Front Panel Section .150 7-6.Base Panel Section .151 7-7.AMP Board Section .152 7-8.Tuner Section .153 7-9.Main

34、 Board Section .154 7-10. Digital/I. link Board Section.155 7-11. Back Panel Section.156 7-12. Transformer Section.157 7-13. MOTHER Board Section .158 8.ELECTRICAL PARTS LIST.159 6-34. Schematic Diagram SUB Board (1/2) . 56 6-35. Schematic Diagram SUB Board (2/2) . 57 6-36. Printed Wiring Board PREO

35、UT Board . 58 6-37. Schematic Diagram PREOUT Board . 59 6-38. Printed Wiring Board VIDEO Board . 60 6-39. Schematic Diagram VIDEO Board . 61 6-40. Printed Wiring Board S-VIDEO Board . 62 6-41. Schematic Diagram S-VIDEO Board . 63 6-42. Printed Wiring Board COMPONENT Section (Component Side) . 64 6-4

36、3. Printed Wiring Boards COMPONENT Section (Conductor Side) . 65 6-44. Schematic Diagram COMPONENT Section (1/4) . 66 6-45. Schematic Diagram COMPONENT Section (2/4) . 67 6-46. Schematic Diagram COMPONENT Section (3/4) . 68 6-47. Schematic Diagram COMPONENT Section (4/4) . 69 6-48. Printed Wiring Bo

37、ard TRIGGER Board . 70 6-49. Schematic Diagram TRIGGER Board . 71 6-50. Schematic Diagram DVI Board (1/2) . 72 6-51. Schematic Diagram DVI Board (2/2) . 73 6-52. Printed Wiring Board DVI Board . 74 6-53. Schematic Diagram AMP Board (1/5) . 75 6-54. Schematic Diagram AMP Board (2/5) . 76 6-55. Schema

38、tic Diagram AMP Board (3/5) . 77 6-56. Schematic Diagram AMP Board (4/5) . 78 6-57. Schematic Diagram AMP Board (5/5) . 79 6-58. Printed Wiring Board AMP Board (Component Side) . 80 6-59. Printed Wiring Board AMP Board (Conductor Side) . 81 6-60. Printed Wiring Board FCOIL Board . 82 6-61. Schematic

39、 Diagram FCOIL Board . 83 6-62. Printed Wiring Board RCOIL Board . 84 6-63. Schematic Diagram RCOIL Board . 85 6-64. Printed Wiring Boards SP Section . 86 6-65. Schematic Diagram SP Section . 87 6-66. Printed Wiring Board I. LINK Board (Component Side) . 88 6-67. Printed Wiring Board I. LINK Board (

40、Conductor Side) . 89 6-68. Schematic Diagram I. LINK Board (1/4) . 90 6-69. Schematic Diagram I. LINK Board (2/4) . 91 6-70. Schematic Diagram I. LINK Board (3/4) . 92 6-71. Schematic Diagram I. LINK Board (4/4) . 93 6-72. Printed Wiring Board DISPLAY Section . 94 6-73. Schematic Diagram DISPLAY Section . 95 6-74. Printed Wiring Boards PANEL