《Sony-STRDG710-rec-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Sony-STRDG710-rec-sm 电路图 维修手册.pdf（86页珍藏版）》请在收音机爱好者资料库上搜索。
1、1 SERVICE MANUALUS Model Canadian Model AEP Model UK Model E Model Australian Model STR-DG710 MULTI CHANNEL AV RECEIVER Amplifier section Models of area code US, CND 1) Minimum RMS Output Power (8 ohms, 20 Hz 20 kHz, THD 0.09%) 95 W + 95 W Stereo Mode Output Power (8 ohms, 1 kHz, THD 1%) 105 W + 105
2、 W Surround Mode Output Power 2) (8 ohms, 1 kHz, THD 10%) 140 W/ch Models of area code AEP, UK, AUS 3) Minimum RMS Output Power (8 ohms, 20 Hz 20 kHz, THD 0.09%) 85 W + 85 W Stereo Mode Output Power (8 ohms, 1 kHz, THD 1%) 100 W + 100 W Surround Mode Output Power 2) (8 ohms, 1 kHz, THD 10%) 140 W/ch
3、 Models of area code SP, MY, TH 3) Minimum RMS Output Power (8 ohms, 20 Hz 20 kHz, THD 0.09%) 70 W + 70 W Stereo Mode Output Power (8 ohms, 1 kHz, THD 1%) 80 W + 80 W Surround Mode Output Power 2) (8 ohms, 1 kHz, THD 10%) 120 W/ch 1) Measured under the following conditions: Area codePower requiremen
4、ts US, CND120 V AC, 60 Hz SPECIFICATIONS 2) Reference power output for front, center, surround and surround back speakers. Depending on the sound field settings and the source, there may be no sound output. 3) Measured under the following conditions: Area codePower requirements AEP, UK, MY, SP, TH23
5、0 V AC, 50 Hz AUS240 V AC, 50 Hz Frequency response Analog10 Hz 70 kHz +0.5/2 dB (with sound field and equalizer bypassed) Inputs AnalogSensitivity: 500 mV/50 kohms S/N 4) : 96 dB (A, 500 mV 5) Digital (Coaxial)Impedance: 75 ohms S/N: 100 dB (A, 20 kHz LPF) Digital (Optical)S/N: 100 dB (A, 20 kHz LP
6、F) Outputs (Analog) AUDIO OUTVoltage: 500 mV/10 kohms SUB WOOFERVoltage: 2 V/1 kohm Equalizer Gain levels6 dB, 1 dB step 4) INPUT SHORT (with sound field and equalizer bypassed). 5) Weighted network, input level. Ver. 1.1 2007.08 9-887-623-02 2007H04-1 2007.08 Sony Corporation Home Audio Division Pu
7、blished by Sony Techno Create Corporation Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic”, “Surround EX”, and the double-D symbol are trademarks of Dolby Laboratories. “DTS”, “DTS-ES Neo:6” are registered trademarks of DTS, Inc. “96/24” is a trademark of DTS, Inc. This recei
8、ver incorporates High-Definition Multimedia Interface (HDMITM) technology. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. Continued on next page XM is a registered trademark of XM Satellite Radio Inc. AUDIO POWER SPECIFICAT
9、IONS (US model) POWER OUTPUT AND TOTAL HARMONIC DISTORTION: With 8 ohm loads, both channels driven, from 20 20,000 Hz; rated 95 watts per channel minimum RMS power, with no more than 0.09% total harmonic distortion from 250 milliwatts to rated output. RadioFans.CN 收音机爱 好者资料库 2 STR-DG710 FM tuner sec
10、tion Tuning range87.5 - 108.0 MHz AntennaFM wire antenna Antenna terminals75 ohms, unbalanced Intermediate frequency10.7 MHz AM tuner section Tuning range Area codeTuning scale 10 kHz step9 kHz step US, CND530 531 1,710 kHz 6)1,710 kHz 6) AEP, UK, AUS, SP,531 MY, TH1,602 kHz AntennaLoop antenna Inte
11、rmediate frequency450 kHz 6) You can change the AM tuning scale to 9 kHz or 10 kHz. After tuning in any AM station, turn off the receiver. While holding down TUNING MODE, press ?/1. All preset stations will be erased when you change the tuning scale. To reset the scale to 10 kHz (or 9 kHz), repeat t
12、he procedure. Video section Inputs/Outputs Video:1 Vp-p/75 ohms COMPONENT VIDEO:Y: 1 Vp-p/75 ohms PB/CB: 0.7 Vp-p/75 ohms PR/CR: 0.7 Vp-p/75 ohms 80 MHz HD Pass Through SAFETY-RELATED COMPONENT WARNING! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE P
13、ARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. General Power requirements Area codePower requirements US, CND120 V AC, 60 Hz AEP, UK230 V AC, 50/60 Hz AUS240 V AC, 50 Hz MY, SP,
14、 TH230 240 V AC, 50/60 Hz Power output (DIGITAL MEDIA PORT) DC OUT:5 V, 700 mA Power consumption Area codePower consumption US250 W CND340 VA AEP, UK, AUS220 W MY, SP, TH210 W Power consumption (during standby mode) 0.3 W (when “CONTROL” in VIDEO menu is set to “CTRL OFF”) Dimensions (w/h/d) (Approx
15、.) 430 157.5 310 mm (16 7/8 6 2/8 12 2/8 inches) including projecting parts and controls Mass (Approx.)7.8 kg (17 lb 4 oz) Supplied accessories FM wire antenna (aerial) (1) AM loop antenna (aerial) (1) Remote commander RM-AAU014 (1) (US, CND) Remote commander RM-AAU015 (1) (EXCEPT US, CND) R6 (size-
16、AA) batteries (2) Optimizer microphone (ECM-AC2 or ECM-AC2a) (1) Design and specifications are subject to change without notice. Abbreviation CND : Canadian model AUS : Australian model SP: Singapore model TH: Thai model ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT! LES COMPOSANTS IDENTIFIS PAR UN
17、E MARQUE 0 SUR LES DIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONT CRITIQUES POUR LA SCURIT DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PICES SONY DONT LES NUMROS SONT DONNS DANS CE MANUEL OU DANS LES SUPPLMENTS PUBLIS PAR SONY. Ver. 1.1 RadioFans.CN 收音机爱 好者资料库 3 STR-DG710 MODEL IDE
18、NTIFICATION BACK PANEL Part No. MODELPART No. US2-898-467-0s Canadian2-898-467-1s AEP, UK2-898-467-2s Malaysia, Singapore2-898-467-3s Australian2-898-467-4s Thai2-898-467-5s 1.5 k0.15 F AC voltmeter (0.75 V) To Exposed Metal Parts on Set Earth Ground SAFETY CHECK-OUT (US MODEL) After correcting the
19、original service problem, perform the follow- ing safety check before releasing the set to the customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE TEST The AC leakage from any expos
20、ed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microampers.). Leakage current can be measured by any one of three methods. 1.A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow t
21、he manufacturers instructions to use these instruments. 2.A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3.Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indica- tion is 0.75 V, so
22、analog meters must have an accurate low- voltage scale. The Simpson 250 and Sanwa SH-63Trd are ex- amples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suit- able. (See Fig. A) Fig. A. Using an AC voltmeter to check AC leakage. UNLEAD
23、ED SOLDER Boards requiring use of unleaded solder are printed with the lead- free mark (LF) indicating the solder contains no lead. (Caution:Some printed circuit boards may not come printed with the lead free mark due to their particular size.) : LEAD FREE MARK Unleaded solder has the following char
24、acteristics. Unleaded solder melts at a temperature about 40C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350C. Caution:The pr
25、inted pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. Usable with ordinary solder I
26、t is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. Notes on Chip Component Replacement Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor may be damaged by heat. NOTE OF REPLACING THE IC3511 AND IC3513 ON THE HDM
27、I RE BOARD When IC3511 and IC3513 on the HDMI RE board are damaged, exchange the new HDMI RE board for the HDMI RE board which IC damaged. When throwing away the HDMI RE board, be sure to throw away after destroying IC3511 and IC3513 physically with the hammer etc. Ver. 1.1 RadioFans.CN 收音机爱 好者资料库 4
28、 TABLE OF CONTENTS 1. GENERAL Description and location of parts. 5 2. DISASSEMBLY 2-1. Case .10 2-2. Back Panel Section. 11 2-3. Front Panel Section .11 2-4. DIGITAL Board . 12 2-5. MAIN Board Section . 12 2-6. STANDBY Board . 13 3. TEST MODE. 14 4. FM TUNER CHECK. 15 5. DIAGRAMS 5-1. Circuit Boards
29、 Location .16 5-2. Block Diagram Tuner/Audio Section . 17 5-3. Block Diagram Digital Section .18 5-4. Block Diagram Video Section . 19 5-5. Block Diagram HDMI RE Section . 20 5-6. Block Diagram XM Section .21 5-7. Block Diagram Key/Display Section . 22 5-8. Block Diagram Output/Power Section . 23 5-
30、9. Printed Wiring Boards Main Section . 25 5-10. Schematic Diagram Main Section (1/2) . 26 5-11. Schematic Diagram Main Section (2/2) . 27 5-12. Printed Wiring Board Digital Section (1/2) . 28 5-13. Printed Wiring Board Digital Section (2/2) . 29 5-14. Schematic Diagram Digital Section (1/3) .30 5-1
31、5. Schematic Diagram Digital Section (2/3) .31 5-16. Schematic Diagram Digital Section (3/3) .32 5-17. Printed Wiring Boards DCAC, Power Key Section . 33 5-18. Schematic Diagram DCAC, Power Key Section .33 5-19. Printed Wiring Boards Video Section . 34 5-20. Schematic Diagram Video Section . 35 5-21
32、. Printed Wiring Board HDMI RE Section (1/2) .36 5-22. Printed Wiring Board HDMI RE Section (2/2) .37 5-23. Schematic Diagram HDMI RE Section (1/2) . 38 5-24. Schematic Diagram HDMI RE Section (2/2) . 39 5-25. Printed Wiring Board XM Section . 40 5-26. Schematic Diagram XM Section . 41 5-27. Printed
33、 Wiring Board Display Section . 42 5-28. Schematic Diagram Display Section .43 5-29. Printed Wiring Board Power Section . 44 5-30. Schematic Diagram Power Section . 44 5-31. Printed Wiring Board DCDC Section . 45 5-32. Schematic Diagram DCDC Section .45 6. EXPLODED VIEWS 6-1. Case Section . 64 6-2.
34、Front Panel Section .65 6-3. Back Panel Section. 66 6-4. Chassis Section . 67 7. ELECTRICAL PARTS LIST. 68 STR-DG710 5 STR-DG710 SECTION 1 GENERALThis section is extracted from instruction manual. 5US Getting Started Description and location of parts Getting Started Front panel ?/1 AUTO CAL MIC SPEA
35、KERS (OFF/A/B) PHONES VIDEO 3 IN/PORTABLE AV IN VIDEOL AUDIO R MEMORY/ ENTER CATEGORY MODECATEGORY TUNING 2CHA.F.D.MOVIEMUSICAUTO CALDIRECT DISPLAYINPUT MODE INPUT SELECTOR MASTER VOLUME TUNING MODE 9q;qhqaqdqsqgqf 813567 NameFunction A ?/1 (on/standby) Press to turn the receiver on or off (page 26,
36、 34, 35, 55, 82). B SPEAKERS (OFF/A/B) Press to select the front speaker system (page 27). C TUNING MODE Press or turn to operate the tuner (FM/AM/XM) (page 55). TUNING +/ MEMORY/ ENTER D DisplayThe current status of the selected component or a list of selectable items appears here (page 7). E Remot
37、e sensor Receives signals from remote commander. F DISPLAYPress to select information displayed on the display (page 73). NameFunction G INPUT MODEPress to select the input mode when the same components are connected to both digital and analog jacks (page 67). H MASTER VOLUME Turn to adjust the volu
38、me level of all speakers at the same time (page 32, 33, 34, 35). I DIRECTPress to listen to high quality analog sound (page 54). J AUTO CALPress to activate the Auto Calibration function (page 29). K INPUT SELECTOR Turn to select the input source to play back (page 33, 34, 35, 54, 56, 58, 59, 67, 72
39、, 74). 24 continued US, Canadian MODEL 6US NameFunction L 2CHPress to select a sound field (page 49). A.F.D. MOVIE MUSIC M CATEGORY MODE Used when listening to XM Radio (page 60). CATEGORY +/ N VIDEO 3 IN/ PORTABLE AV IN jacks Connects to a portable audio/ video component such as a camcorder or vide
40、o game (page 24, 33). O AUTO CAL MIC jack Connects to the supplied optimizer microphone for the Auto Calibration function (page 28). P PHONES jack Connects to headphones (page 78). 7US Getting Started About the indicators on the display SWLFE SP A SP B LC SLS ;D EX;PL IIx;PLOPTDTS -ES CAT96/24MEMORY
41、ST MONOD.RANGECOAXHDMINEO:6 SB R SR 12345678q;9 qaqsqhqfqgqd NameFunction A SWLights up when sub woofer selection is set to “YES” (page 45) and the audio signal is output from the SUB WOOFER jack. B LFELights up when the disc being played back contains an LFE (Low Frequency Effect) channel and the L
42、FE channel signal is actually being reproduced. C SP A/SP BLights up according to the speaker system used. However, these indicators do not light up if the speaker output is turned off or if headphones are connected. D ; D/ ; D EX “; D” lights up when the receiver is decoding Dolby Digital signals.
43、“; D EX” lights up when the receiver is decoding Dolby Digital Surround EX signals. Note When playing a Dolby Digital format disc, be sure that you have made digital connections and that INPUT MODE is not set to “ANALOG” (page 67). NameFunction E ; PL/ ; PLII/ ; PLIIx “; PL” lights up when the recei
44、ver applies Pro Logic processing to 2 channel signals in order to output the center and surround channel signals. “; PLII” lights up when the Pro Logic II Movie/Music/ Game decoder is activated. “; PLIIx” lights up when the Pro Logic IIx Movie/Music/ Game decoder is activated. However, these indicators do not light up if both the center and surround speakers are set to “NO” (page 39) and you select a sound field using t
免费区 
