《Sony-STRV5550-rec-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Sony-STRV5550-rec-sm 电路图 维修手册.pdf（52页珍藏版）》请在收音机爱好者资料库上搜索。
1、STR-V5550/V7770 E Model Chinese Model SERVICE MANUAL FM STEREO/FM-AM RECEIVER MICROFILM SPECIFICATIONS This set is the tuner and amplifier section in MHC-V5550/V7770AV. Amplifier section The following measured at AC 230V 50/60 Hz DIN power output (Rated) (FRONT) 95 + 95W (6 at 1kHz DIN) Continuous R
2、MS power output (Reference) FRONT SPEAKER: 110 + 110W (6 at 1kHz, 10% THD) CENTER SPEAKER: 55W (8 at 1kHz, 10% THD) (V7770) REAR SPEAKER: 35 + 35W (8 at 1kHz, 10% THD) (V7770) The following measured at AC 120, 220, 240V 50/60Hz DIN power output (Rated) (FRONT) 100 + 100W (6 at 1kHz DIN) Continuous R
3、MS power output (Reference) FRONT SPEAKER: 120 + 120 W (6 at 1kHz, 10% THD) CENTER SPEAKER: 60W (8 at 1kHz, 10% THD) (V7770) REAR SPEAKER: 40 + 40W (8 at 1kHz 10% THD) (V7770) Peak music power output 2400W (V7770) 2000W (V5550) InputsMD/VIDEO 1 IN (phone jacks): voltage 450/250mV, impedance 47k AV I
4、NPUT AUDIO (phone jacks): voltage 250mV, impedance 47k MIX MIC 1/2 (phone jack): sensitivity 1mV, impedance 10k OutputMD/VIDEO 1 OUT (phono jacks): voltage 450/250mV, impedance 1k PHONES (stereo phone jack): accepts headphones of 8 or more. FRONT SPEAKER: accepts impedance of 6 to 16 CENTER SPEAKER:
5、 accepts impedance of 8 to 16 (V7770) REAR SPEAKER: accepts impedance of 8 to 16 SUPER WOOFER: Voltage 1V, impedance 1k Photo : STR-V7770 Tuner section FM stereo, FM/AM superheterodyne tuner FM tuner section Tuning range87.5 108.0MHz AerialFM lead aerial Aerial terminals75 unbalanced Intermediate fr
6、equency10.7MHz AM tuner section Tuning range Thai models:531 1,602kHz (with the AM tuning interval set at 9kHz) 530 1,710kHz (with the AM tuning interval set at 10kHz) Other models:MW: 531 1,602kHz (with the MW tuning interval set at 9kHz) 530 1,710kHz (with the MW tuning interval set at 10kHz) SW:
7、5.95 17.90MHz (with the SW tuning interval set at 5kHz) Intermediate frequency450kHz AntennaAM loop antenna External antenna terminal General Power requirements Chinese, Thai models:220V AC, 50/60Hz Other models:120V or 220V or 230 240, 50/60Hz Adjustable with voltage selector Power consumption300W
8、Dimensions (w/h/d)Approx. 288 205 375mm MassApprox. 8.8kg Design and specifications are subject to change without notice. RadioFans.CN 收音机爱 好者资料库 2 TABLE OF CONTENTS 1. GENERAL3 2. DISASSEMBLY 2-1.Sliding Panel Assembly 5 3. SERVICE MODE6 4. DIAGRAMS 4-1.Circuit Boards Location 10 4-2.Block Diagrams
9、 Main Section 11 Power Section 13 4-3.Printed Wiring Board Main Section 17 4-4.Schematic Diagram Main (1/2) Section (V5550 Model) 19 4-5.Schematic Diagram Main (1/2) Section (V7770 Model) 21 4-6.Schematic Diagram Main (2/2) Section 23 4-7.Schematic Diagram Power Amp Section 25 4-8.Printed Wiring Boa
10、rd Power Amp Section 27 4-9.Schematic Diagram Display Section 29 4-10. Printed Wiring Board Display Section 31 4-11. Schematic Diagram Sliding Panel Section 33 4-12. Printed Wiring Board Sliding Panel Section 35 4-13. Schematic Diagram Surround Amp Section 37 4-14. Printed Wiring Board Surround Amp
11、Section 39 4-15. Printed Wiring Board Trans Section 41 4-16. Schematic Diagram Trans Section 43 4-17. Schematic Diagram AV/Mic Section 44 4-18. Printed Wiring Board AV/Mic Section 45 4-19. IC Block Diagrams 46 4-20. IC Pin Function 49 5. EXPLODED VIEWS 5-1.Case and Sliding Panel Section 52 5-2.Front
12、 Panel Section 53 5-3.Slide Mechanism Section 54 5-4.Circuit Boards and Back Panel Section55 6. ELECTRICAL PARTS LIST56 SAFETY-RELATED COMPONENT WARNING ! COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLAC
13、E THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. MODEL IDENTIFICATION BACK PANEL V5550:Hong Kong, Malaysia, Singapore, Indonesia 4-900-848-5 V7770:Hong Kong, Malaysia, Singapore4-900-848-6 V7770:Thai, Chinese4-900-848-7 V5550:C
14、hinese4-900-848-8 MODELPART No. LABEL MODEL NUMBER No. RadioFans.CN 收音机爱 好者资料库 3 Front Panel SECTION 1 GENERAL 1 MOVIE button 2 MUSIC button 3 GAME button 4 PLACE button 5 P FILE button 6 EFFECT ON/OFF button 7 OPEN/CLOSE button 8 TUNER BAND button 9 STEREO/MONO button ! MEMORY button ! KARAOKE PON/
15、MIX button ! MIC LEVEL/ECHO VOL dial ! MIX MIC1 jack ! GROOVE button ! VOLUME dial ! ) + button ! ENTER/NEXT button ! MULTI JOG STATION dial ! 0 button NON-STOP button EDIT button FLASH button PLAY MODE button REPEAT button PHONES jack LOOP button CLOCK/TIMER SET button TIMER SELECT button FUNCTION
16、button # PROLOGIC button # DSP button # DBFB button # DISPLAY/DEMO button # I/u (POWER) button # MIX MIC2 jack # KEY CONTROL (n) # KEY CONTROL () 1234567 8 9 ! ! ! ! ! # ! # # # #! # # Photo : STR-V7770 RadioFans.CN 收音机爱 好者资料库 4 Rear Panel 1 SYSTEM CONTROL jack 2 ANTENNA terminal 3 CENTER SPEAKER te
17、rminal 4 REAR SPEAKER terminal 5 MONITOR OUT jack 6 FRONT SPEAKER terminal 7 MD/VIDEO 1 jack 2 453 1 6 7 Photo : STR-V7770 (Chinese model) 5 SECTION 2 DISASSEMBLY Note: Follow the disassembly procedure in the numerical order given. 2-1. SLIDING PANEL ASSEMBLY NOTE FOR INSTALLATION (LEVEL SLIDER) (Pe
18、rform this DISASSEMBLY after the front panel is removed.) NOTE : Attach in the reverse order, but make sure the rollers (a, b) of the holder (L) assembly and holder (R) assembly fit into the grooves of the level slider. 4 Flat type cable (19 core) 2 Screw (BVTP 3 8) 3 Holder level 5 Sliding panel as
19、sembly Slide mechanism 1 Push the OPEN/CLOSE button to open the Sliding panel assembly. 1 Screw (BVTP2.6 8) 4 Four screws (BVTP2.6 8) 5 Holder (L) assembly a a b b 6 Four screws (BVTP2.6 8) 7 Holder (R) assembly 8 Remove the Level slider direction of arrow. 2 Screw (BVTP2.6 8) 3 Top bracket 6 SECTIO
20、N 3 SERVICE MODE Connections and Operations When Used Alone Normally, use the unit connected to the HTC-V5550 as follows. Basically, when servicing the unit, connect the unit as follows. Even when not connected to the HTC-V5550, the unit can operate alone as it mounts a power supply (some functions
21、will however not be available). MC Cold Reset The cold reset clears all data including preset data stored in the RAM to initial conditions. Execute this mode when returning the set to the customer. Procedure: 1.Press three buttons EDIT , ENTER/NEXT , and DISPLAY/DEMO simultaneously. 2.The fluorescen
22、t indicator tube becomes blink instantaneously, and the set is reset. CD Delivery Mode (This mode can be used only when the HTC-V5550 is connected.) This mode moves the pick-up to the position durable to vibration. Use this mode when returning the set to the customer after repair. Procedure: 1.Press
23、 1/u button to turn the set ON. 2.Press LOOP button and 1/u button simultaneously. 3.A message “LOCK” is displayed on the fluorescent indicator tube, and the CD delivery mode is set. MC Hot Reset This mode resets the set with the preset data kept stored in the memory. The hot reset mode functions sa
24、me as if the power cord is plugged in and out. Procedure: 1.Press three buttons REPEAT , ENTER/NEXT , and DISPLAY/DEMO simultaneously. 2.The fluorescent indicator tube becomes blink instantaneously, and the set is reset. Sled Servo Mode (This mode can be used only when the HTC-V5550 is connected.) T
25、his mode can run the CD sled motor freely. Use this mode, for instance, when cleaning the pick-up. Procedure: 1.Select the function “CD”. 2.Press three buttons FLASH , ENTER/NEXT , and KARAOKE PON/MIX simultaneously. 3.The Sled Servo mode is selected, if “CD” is blinking on the fluorescent indicator
26、 tube. 4.With the CD in stop status, press ) + button move the pick-up to outside track, or 0 button to inside track. 5.To exit from this mode, perform as follows: 1) Move the pick-up to the most inside track. 2) Press three buttons in the same manner as step 2. Note: Always move the pick-up to most
27、 inside track when exiting from this mode. Otherwise, a disc will not be unloaded. Do not run the sled motor excessively, otherwise the gear can be chipped. Change-over of FUNCTION Name The FUNCTION name of external input terminal can be changed over to VIDEO 1 or MD. With the FUNCTION selected to “
28、MD”, about 5dB mute is applied to the input gain. Procedure: 1.Press 1/u button to turn the set OFF. 2.Press 1/u button together with FUNCTION button, and the power is turned on, the display of fluorescent indicator tube changes to “MD” or “VIDEO 1” instantaneously, and thus the FUNCTION is changed
29、over. Change-over of AM Tuner Step between 9kHz and 10kHz A step of AM channels can be changed over between 9kHz and 10kHz. Procedure: 1.Press 1/u button to turn the set ON. 2.Select the function “TUNER”, and press TUNER/BAND button to select the BAND “MW”. 3.Press 1/u button to turn the set OFF. 4.
30、Press ENTER/NEXT and 1/u buttons simultaneously, and the display of fluorescent indicator tube changes to “MW step 10” or “MW step 9”, and thus the channel step is changed over. AC IN UNITHTC-V5550 SYSTEM CONTROL 17P 7 LED and Fluorescent Indicator Tube All Lit, Key Check Mode (Do not connect the HT
31、C-V5550.) Procedure: 1.Press 1/u button to turn the set ON. 2.Press the OPEN/CLOSE button to open the sliding panel. 3.Press three buttons DELAY , ENTER/NEXT , and DISPLAY/DEMO simultaneously. 4.LEDs and fluorescent indicator tube are all turned on. Each time the MOVIE button is pressed, the fluores
32、cent indicator tube lights up as follows: lights up completely n lights up partially 1 n lights up partially 2 n lights up completely. 5.Press GAME button, and the key check mode is activated. 6.In the key check mode, the fluorescent indicator tube displays “K V0 J0”. Each time a button is pressed,
33、“K”value decreases. However, once a button is pressed, it is no longer taken into account. ( means the total of buttons) “J” Value increases like 1, 2, 3 . if rotating JOG knob in “+” direction, or it decreases like 0, 9, 8 . if rotating in “-” direction. “V” Value increases like 1, 2, 3 . if rotati
34、ng VOLUME knob in “+” direction, or it decreases like 0, 9, 8 . if rotating in “-” direction. 7.Pressing all buttons lights up the fluorescent indicator tube completely. 8.To exit from this mode, press three buttons EDIT , ENTER/NEXT and DISPLAY/DEMO simultaneously. (COLD RESET) 9.To exit from this
35、mode, press three buttons in the same manner as step 1, or disconnect the power cord. CD, TAPE Deck Aging Mode (This mode can be used only when the HTC-V5550 is connected.) This mode can be used for checking the operations of the CD player and tape deck. When problems occur; Aging stops, and the sto
36、pped state is displayed on the fluorescent indicator tube. When no problems; Aging continues. Preparations: Set the CD on the DISC1 tray. Insert a commercially available tape for recording (tapes which contents can be erased, etc.) in decks A and B. Setting the aging mode: Press the PLAY MODE button
37、, ENTER/NEXT button, and STEREO/MONO button together. When the aging mode is set, the CD roulette mark blinks. To exit the mode, press the 1/u button and turn OFF the power. Sequence: The aging mode is executed in the following sequence. If the function is set to “CD” when the aging mode is set, agi
38、ng is performed starting from the CD player. When set to “TAPE A” or “TAPE B”, aging is started from deck A. If the function is set to others, aging will not be started until the function is switched to CD or TAPE. Display of status: The aging status is displayed on the fluorescent indicator tube. N
39、ormally, the CD player displays the remaining aging time. But if operations ended abnormally, it displays the cause. During the aging of the tape deck, the operations performed will be displayed. If operations ended abnormally, this will be displayed at the fluorescent display tube. CD Player During
40、 normal operations: Display of fluorescent indicator tube *1- *: Displays “CD” and the remaining aging time (minutes) alternately. The remaining aging time is counted down from 12. : Track number being accessed. Aging of CD player (12 minutes) Aging of deck A Aging of deck B 12 minutes 8 When operat
41、ions end abnormally: Display of fluorescent display tube Display of OperationsOperation TAPE A AG-1 TAPE A AG-2 TAPE A AG-3 TAPE A AG-4 TAPE A AG-5 TAPE B AG-1 TAPE B AG-2 TAPE B AG-3 TAPE B AG-4 TAPE B AG-5 TAPE A REW TAPE A FWD TAPE A FF TAPE A REV TAPE A REW TAPE B REW TAPE B FWD TAPE B FF TAPE B
42、 REV TAPE B REW Timing of Ending Shutoff 2 minute playback 20 seconds or shutoff 2 minutes playback Shutoff Shutoff 2 minute playback 20 seconds or shutoff 2 minute playback Shutoff Operations during aging Operations are performed in the following sequence during aging. 1.The CD tray rotates and dis
43、c 1 is selected. 2.Chucking is performed. 3.TOC is read. 4.Track 1 played back for 2 seconds. 5.The last track is played back for 2 seconds. 6.1 to 5 is repeated. 7.After 12 minutes of aging, aging is switched to the tape deck. 1.The tape in deck A is rewound to the head. 2.The FWD side is played ba
44、ck for 2 minutes. 3.The tape is fast forwarded (FF) for 20 seconds. The following procedure is performed when the tape end is reached before the 20 seconds. 4.The REV side is played back for 2 minutes. 5.The tape is rewound to the head (REW). 6.The tape in deck B is rewound to the head. 7.The FWD si
45、de is played back for 2 minutes. 8.The tape is fast forwarded (FF) for 20 seconds. The following procedure is performed when the tape end is reached before the 20 seconds. 9.The REV side is played back for 2 minutes. 10. The tape is rewound to the head (REW). 11. Aging is switched to the CD player.
46、Display Main Cause NO DISC ERR FOCUS1 ERR FOCUS2 ERR GFS ERR FBIAS ERR SENSOR ERR TABLE ERR TRAY ERR DISC 1 is NO DISC from the beginning Focus is not imposed properly The focus deviated several times after the disc rotated normally GFS ERROR Error during focus bias adjustment DISC 1 was found to be
47、 NO DISC by the disc sensor The table did not rotate normally The tray containing the BD did not operate normally Tape Deck 9 PANEL Aging Mode This mode is used for opening and closing the sliding panel continuously. Setting the aging mode : With the set at standby condition, press FLASH button, ENT
48、ER/NEXT button and STEREO/MONO button together. The aging will start and sliding panel will follow aging sequence as described below. When problems occur ; Aging stops and “AGING ERROR” is displayed on the fluorescent indicator tube. When no problems; Aging is carried out repeatedly. After 65000 tim
49、es, “AGING STOP” is displayed and aging stops. Aging Sequence Counts upnnPanel openPanel closenStops for one second in the opened state Stops for one second in the closed state Each time the DISPLAY/DEMO button is pressed, the display switches as follows. Aging (No. of agings carried out) OP Max . (Maximum time taken for OPEN:In seconds) OP Min . (Minimum time taken for OPEN:In seconds) CL Max . (Maximum time taken for CLOSE:In seconds) CL Min . (Minimum
免费区 
