Sony-CDPCX57-cd-sm 电路图 维修手册.pdf

《Sony-CDPCX57-cd-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Sony-CDPCX57-cd-sm 电路图 维修手册.pdf（58页珍藏版）》请在收音机爱好者资料库上搜索。

1、MICROFILM SERVICE MANUAL COMPACT DISC PLAYER US Model Canadian Model AEP Model UK Model E Model Australian Model Compact disc player LaserSemiconductor laser ( = 780 nm) Emission duration: continuous Laser outputMax 44.6 W* * This output is the value measured at a distance of 200 mm from the objecti

2、ve lens surface on the Optical Pick-up block with 7 mm aperture. Frequency response20 Hz to 20 kHz 1dB Signal-to-noise ratioMore than 107 dB Dynamic rangeMore than 88 dB Harmonic distortionLess than 0.013% Channel separationMore than 100 dB Outputs SPECIFICATIONS CDP-CX57 Model Name Using Similar Me

3、chanism CDP-CX50/CX571 CD Mechanism TypeCDM-46C1 Base Unit TypeKSM-213BFN/M-NP Optical Pick-up TypeKSS-213B/S-N JackMaximumLoad impedance typeoutput level LINE OUTPhono2VOver 10 kilohms Jacks(at 50 kilohms) DIGITALOptical18 dBmWave length: 660 nm OUToutput (OPTICAL)connector Where purchasedPower req

4、uirements US/Canada120 V AC, 60 Hz Australia240 V AC, 50/60 Hz UK220 V 230 V AC, 50/60 Hz Other countries110 V 120 V or 220 V 240 V AC, adjustable, 50/60 Hz General Power requirements Power consumption12 W Dimensions (approx.)When the front cover is closed (w/h/d)430 182.5 295 mm (17 7 1/4 11 5/8 in

5、.) incl. projecting parts When the front cover is open 430 182.5 414 mm (17 7 1/4 16 3/8 in.) incl. projecting parts Mass (approx.)5.5 kg (12 lbs 3 oz) Supplied accessories Audio cord (2 phono plugs 2 phono plugs) (1) CONTROL A1 cord (supplied for Canadian models only) (1) Remote commander (remote)

6、(1) Sony SUM-3 (NS) batteries (2) CD booklet holder (1) and Label (1) Design and specifications are subject to change without notice. RadioFans.CN 收音机爱 好者资料库 2 TABLE OF CONTENTS 1.SERVICING NOTES.2 2.GENERAL.6 3.DISASSEMBLY.7 4.TEST MODE. 11 5.MECHANICAL ADJUSTMENTS. 14 6.ELECTRICAL ADJUSTMENTS. 17

7、7.DIAGRAMS. 20 7-1.Block Diagrams BD Section. 23 Main Section . 25 7-2.Printed Wiring Board BD Section . 27 7-3.Schematic Diagram BD Section . 29 7-4.Printed Wiring Board Audio Section . 31 7-5.Schematic Diagram Audio Section . 33 7-6.Printed Wiring Board Main Section . 35 7-7.Schematic Diagram Main

8、 Section . 37 7-8.Printed Wiring Boards Panel Section . 39 7-9.Schematic Diagram Panel Section . 41 7-10. Printed Wiring Boards Sensor/Motor Section . 43 7-11. Schematic Diagram Sensor/Motor Section . 45 7-12. IC Pin Function Description . 49 8.EXPLODED VIEWS. 55 9.ELECTRICAL PARTS LIST. 61 CAUTION

9、Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. The laser component in this product is capable of emitting radiation exceeding the limit for Class 1. This appliance is classified as a CLASS 1 LASER product. The

10、 CLASS 1 LASER PRODUCT MARKING is located on the rear exterior. 4-997-568-0 4-997-568-1 4-997-568-2 4-997-568-3 4-997-568-4 4-997-568-5 4-997-568-6 US model Canadian model AEP, AED model UK model Australian model E model Singapore model PART No.MODEL MODEL IDENTIFICATION BACK PANEL Abbreviation AED:

11、 North European PART No. CAUTION:INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED. AVOID EXPOSURE TO BEAM. ADVARSEL :USYNLIG LASERSTRLING VED BNING NR SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION. UNDG UDSAETTELSE FOR STRLING. VORSICHT :UNSICHTBARE LASERSTRAHLUNG, WENN ABDECKUNG GEFFNET UND SIC

12、HEREITSVERRIEGELUNG BERBRCKT. NICHT DEM STRAHL AUSSETZEN. VARO!:AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALT- TIINA NKYMTTMLLE LASERSTEILYLLE. L KATSO STEESEEN. VARNING:OSYNLING LASERSTRLING NR DENNA DEL R PPNAD OCH SPRREN R URKOPPLAD. BETRAKTA EJ STRLEN. ADVERSEL :USYNLIG LASERSTRLING NR DEKSEL

13、 PNES OG SIKKERHEDSLS BRYTES. UNNG EKSPONERING FOR STRLEN. VIGYAZAT!:A BURKOLAT NYITSAKOR LTHATATLAN LZERSU- GRVESZLY! KERLJE A BESUGRZST! (Except for the customers in the United States and Canada) The following caution label is located inside the unit. SECTION 1 SERVICING NOTES RadioFans.CN 收音机爱 好者

14、资料库 3 ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT! LES COMPOSANTS IDENTIFIS PAR UNE MARQUE ! SUR LES DIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONT CRITIQUES POUR LA SCURIT DE FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS QUE PAR DES PICES SONY DONT LES NUMROS SONT DONNS DANS CE MANUEL OU DANS

15、 LES SUPPLMENTS PUBLIS PAR SONY. SAFETY-RELATED COMPONENT WARNING! COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR

16、IN SUPPLEMENTS PUB- LISHED BY SONY. SAFETY CHECK-OUT After correcting the original service problem, perform the follow- ing safety check before releasing the set to the customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Ch

17、eck leakage as described below. LEAKAGE The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microampers.). Leakage current can be measured by any one of three methods. 1.A commer

18、cial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers instructions to use these instruments. 2.A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3.Measuring the voltage drop across a resistor by means of a VOM or b

19、attery-operated AC voltmeter. The “limit” indica- tion is 0.75 V, so analog meters must have an accurate low- voltage scale. The Simpson 250 and Sanwa SH-63Trd are ex- amples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suit- able. (

20、See Fig. A) Fig. A.Using an AC voltmeter to check AC leakage. 1.5 k0.15 F AC voltmeter (0.75 V) To Exposed Metal Parts on Set Earth Ground The laser diode in the optical pick-up block may suffer electro- static break-down because of the potential difference generated by the charged electrostatic loa

21、d, etc. on clothing and the human body. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK The laser

22、 beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pick-up block. Therefore, when checking the laser diode emis- sion, observe from more than 30 cm away from the objective lens. LASER DIODE AND FOCUS SEARCH OPERATION CHECK Carr

23、y out the “S curve check” in ”CD section adjustment” and check that the S curve waveform is output repeatedly. NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT RadioFans.CN 收音机爱 好者资料库 4 CD-TEXT TEST DISC This unit is able to display the test data (character information) written in the CD on

24、its fluorescent indicator tube. The CD-TEXT TEST DISC (TGCS-313:4-989-366-01) is used for checking the display. To check, perform the following procedure. Checking Method: 1. Turn ON the power, set the disc on the disc table with the side labeled as “test disc” as the right side, close the front cov

25、er, and chuck the disc. 2. Press the button and play back the disc. 3. The following will be displayed on the fluorescent indicator tube. Display : 1kHz/0 dB/ L ?(38h to 3Fh)N All the same 46A B C D E F G(40h to 47Fh)N All the same 47H I J K L MNO(48h to 4Fh)N All the same 48P QR S T U VW(50h to 57F

26、h)PQR S T U VW (50h to 57h) 49X Y Z _(58h to 5Fh)XY Z _ (58 50a b c d e f g(60h to 67Fh)a b c d e f g (60h to 67h) 51h i j k l m n o(68h to 6Fh)N All the same 52p q r s t u v w(70h to 77Fh)p q r s t u v w (70h to 77h) 53x y z I (78h to 7Fh)x y z (78 54i (A0h to A7h) 8859-1i (A0 is not displayed 55C

27、PR (A8h to AFh)(A8 C P R are not displayed 56 23 (B0h to B7h) (B0 2 3 are not displayed 57 1 (B8h to BFh) (B8 1 are not displayed 58 (C0h to C7Fh) (C0h to C7h) 59 (C8h to CFh)N All the same 60D (D0h to D7Fh)D (D0h to D7h) 61 Y(D8h to DFh) Y (D8 62 (E0h to E7h) (E0h to E7h) 63 (E8h to EFh)N All the s

28、ame 64 (F0h to F7Fh) (F0h to F7h) 65 y(F8h to FFFh) y (F8h to FFh) 66No.66N All the same 67No.67N All the same tototo 99No.99N All the same Table 2: CD-TEXT TEST DISC Recorded Contents and Display (In this unit, some special characters cannot be displayed. This is no a fault.) * TRACK No. Recorded C

29、ontentsDisplay 1 4 1 2 3 4 1 4 1 2 3 4 6 SECTION 2 GENERAL 1I/u (power switch) button 2Front cover 3PLAY MODE button 4REPEAT button 5GROUP FILE button 6Display window 7GROUP 1-5 buttons 8TIME/TEXT button 9INPUT button !MEMO SEARCH button !JOG dial (DISC/CHARACTER/PUSH ENTER knob) !FADER button LOCAT

30、ION OF PARTS AND CONTROLS Front Panel !CHECK button !CLEAR button ! button ! button !p button !P button ! button PLUS ONE button X-FADE button NO DELAY button MEGA CONTROL button PUSH OPEN STANDBY 1/u PULS ONE PLAY MODEREPEATGROUP FILE123 GROUP 45CHECKFADERCLEAR PUSH ENTERg DISC/CHARACTER TIME/TEXT

31、INPUT MEMO SEARCH Pp X-FADE NO DELAY MEGA CONTROL 123456789 ! ! 0 ! ! ! ! ! 7 CASE, FRONT PANEL Note: Follow the disassembly procedure in the numerical order given. SECTION 3 DISASSEMBLY 1two screws (M3 8) 1two screws (M3 8) 4screw (BVTT3 6) 3two screws (BVTT3 6) 6three screws (BVTT3 6) 5wire (flat

32、type) (19 core) (CN503) 2case 7claw 7claw 8front panel 1two screws (M3 8) 5table (50) 4screw (PTPWH2.6 8) 1screw (BVTT3 6) 2connector (NO 806) 3bracket (ILLUMINATION) TABLE (50) 8 CD MECHANISM DECK SECTION AUDIO BOARD, MAIN BOARD 5two screws (BVTT3 10) 3two screws (BVTP3 8) 2reinforcement 5screw (BV

33、TT3 6) 9screw (BVTT3 8) 1screw (BVTT3 6) 9screw (P3 14) 6connector (CN53) !connector (CN61) 0connector (CN51) 7wire (flat type) (9 core) (CN103) 6connector (CN54) !base (CDM) 4ring (B) 0connector (CN52) 7wire (flat type) (16 core) (CN102) 8base (LOADING) 6transformer cover 1two screws 4MAIN board !A

34、UDIO board 3connector (CN 801) 5two screws (BVTT3 6) 1screw (BVTP3 8) 8two screws (BVTT3 6) !connector (CN201) 2ring (A) 7screw (BVTT3 6) 9three screws (BVTP3 10) 9 BASE UNIT BD BOARD, SLED MOTOR (M102) 1wire (flat type) (16 core) (CN101) 8gear cover 2screw (B2 5) 7three claws 4BD board 3Removal fou

35、r solders. !sled motor (M102) 0two screws (2 3) 5claw 9gear (B) (RP) 6gear (A) (S) 1two screws (BTP2.6 8) 6four screws (PTPWH2.6 8) 3screw (BTP2.6 10) 2bracket 4reinforcement (small) 5two tention springs 7base unit 10 OPTICAL PICK-UP (KSS-213B/S-N) 3Remove the optical pick-up to direction of the arr

36、ow A. A 1claw 2sled shaft 11 SECTION 4 TEST MODE ADJ MODE 1.Press the I/ubutton to turn ON the power, and open the front cover. 2.Place the CD on the slit, close the front cover, and chuck the the CD. 3.Press the I/ubutton to turn OFF the power. 4Disconnect the power supply from the outlet. 5.Short-

37、circuit the test point (TP ADJ) and test point (TP GND) of the MAIN board with a lead wire. 6.Insert the power plug into the outlet. The CD is played back automatically and the ADJ mode is set. Prohibits high speed search during accessing Ignores even if GFS becomes L ADJ Mode Special Function Table

38、 (The buttons shown in the () function only when the remote commander provided is used.) ButtonFunction (3) (8) CHECK CLEAR Tracking servo, sled servo OFF Tracking servo, sled servo ON Observation mode during S Automatic eccentricity measurement (Not used for servicing) Display of special functions

39、in ADJ mode Observation mode during S When this mode is set, the below will be displayed. *1 Automatic eccentricity measurement (Not used for servicing) When this mode is set, the below will be displayed.The Sokuteichu count down display will be counted down from 4 to to 1 *2.After counting down, th

40、e eccentricity value will be displayed *3. FLUORESCENT INDICATOR TUBE, LED ALL LIT, AND KEY CHECK MODE 1.Short-circuit the test point (TP ADJ) and test point (TP AFADJ) of the MAIN board with a lead wire. 2.Insert the power plug into the outlet. The whole fluorescent indicator tube lights up. When t

41、he SRAM is faulty, “SRAMNG” will be displayed. 3.Pressing the I/ubutton sets the key check mode. All buttons have individual button numbers. When a button is pressed, the button number is counted up and displayed. Buttons and Corresponding Button Numbers CLEAR CHECK FADER MEMO SEARCH INPUT TIME/TEXT

42、 PUSH ENTER REPEAT PLAY MODE I/u X-FADE NO DELAY GROUP 5 GROUP 4 GROUP 3 GROUP 2 GROUP 1 GROUP FILE P p PLUS ONE MEGA CONTROL DISC/CHARACTER ButtonButton Number or Display ALL DISCS S-JI mode *1 CD1 ALL DISCS Sokuteichu count down display TRACKMIN SEC NEXT DISC DISC CD1 Sokuteichu -4 *2 ALL DISCS CD

43、1 Henshin 021 *3 Eccentricity value 1 DISCS DISC CD1 * Count up displayDisplays button number 0 1 2 3 4 5 6 8 9 14 15 16 17 18 24 25 26 27 28 29 All lit (LED lights up) Partially lit 1 (LED lights up) Partially lit 2 LED lights up Partially lit 3 (LED lights up) Partially lit 4 Each time JOG is rota

44、ted, GROUP FILE 1 2 3 4 5 is displayed on the fluorescent indicator tube, and 1, 2, 3, 4, 5 light up one by one, and GROUP LED 1, 2, 3, 4, 5 lights up one by one. Clockwise : GROUP FILE 1n2n3n4n5 Counterclockwise : GROUP FILE 5n4n3n2n1 STANDBY LED OFF PUSH OPEN (DOOR SW ON) STANDBY LED ON PUSH OPEN

45、(DOOR SW OFF) 12 Partially lit 1 Partially lit 2 Partially lit 3 Partially lit 4 FLUORESCENT INDICATOR TUBE AND LED CHECK MODE This mode is set by pressing the I/ubutton while pressing the CHECK and PLUSONE buttons in order in the power-off (standby) state. The whole fluorescent indicator tube light

46、s up, and the STANDBY, MEGACONTROL, GROUP1-5, PLUSONE, and P LEDs light up. This mode can be exited by pressing the I/ubutton. SHIPMENT MODE (Set to this mode when returning the unit to the user.) This mode is set by pressing the I/ubutton while pressing the PUSHENTER and PLUSONE buttons in order in the power- off (standby) state. The power goes off automatically after the SRAM is all-erased and the BD is opened (loading out state). Test points and connecting po