《Sony-STRDA5300ES-rec-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Sony-STRDA5300ES-rec-sm 电路图 维修手册.pdf（328页珍藏版）》请在收音机爱好者资料库上搜索。
1、SERVICE MANUAL AUDIO POWER SPECIFICATIONS (US model) POWER OUTPUT AND TOTAL HARMONIC DISTORTION: With 8 ohm loads, both channels driven, from 20 20,000 Hz; rated 120 watts per channel minimum RMS power, with no more than 0.09% total harmonic distortion from 250 milliwatts to rated output. Amplifier
2、section POWER OUTPUT (US and Canadian models) Rated Power Output at Stereo Mode1) 2) (8 ohms 20 Hz 20 kHz, THD 0.09%): 120 W + 120 W Reference Power Output at Stereo Mode (4 ohms 20 Hz 20 kHz, THD 0.15%): 120 W + 120 W Reference Power Output (8 ohms 1 kHz, THD 0.7%) FRONT2): 130 W + 130 W CENTER2):
3、130 W SURROUND2): 130 W + 130 W SURROUND BACK2): 130 W + 130 W Reference Power Output (4 ohms 1 kHz, THD 0.7%) FRONT2): 120 W + 120 W CENTER2): 120 W SURROUND2): 120 W + 120 W SURROUND BACK2): 120 W + 120 W 1)Depending on the sound field settings and the source, there may be no sound output. 2)Measu
4、red under the following conditions: Power requirements: 120 V AC, 60 Hz (AEP, Russian, Ukrainian, UK and Chinese models) Rated Power Output at Stereo Mode1) 2) (8 ohms 1 kHz, THD 0.7%): 125 W + 125 W Reference Power Output at Stereo Mode (4 ohms 1 kHz, THD 0.7%): 125 W + 125 W Reference Power Output
5、 (8 ohms 20 Hz 20 kHz, THD 0.09%) FRONT2): 120 W + 120 W CENTER2): 120 W SURROUND2): 120 W + 120 W SURROUND BACK2): 120 W + 120 W Reference Power Output (4 ohms 20 Hz 20 kHz, THD 0.15%) FRONT2): 120 W + 120 W CENTER2): 120 W SURROUND2): 120 W + 120 W SURROUND BACK2): 120 W + 120 W Reference Power Ou
6、tput at Stereo Mode (8 ohms 1 kHz, THD 10%): 150 W + 150 W MULTI CHANNEL AV RECEIVER SPECIFICATIONS Ver. 1.6 2009.05 Continued on next page 9-887-741-07 2009E05-1 2009.05 Sony Corporation AudioDSP board 4two screws (BVTP3 8) 3eight screws (BVTP3 8) qftwo screws (BVTP3 8) qjscrew (BVTP3 8) qatwo scre
7、ws (BVTP3 8) 8four screws (BVTP3 8) 6two connectors (CN2204, CN2207) qhCIS board waCONTROL board qg 5 ql qkthree connectors (CN2012, CN2013, CN2014) w;connector (CN2002) 1six connectors (CN2401, CN2402, CN2403, CN2404, CN2405, CN2406) 2five connectors (CN3509, CN3523, CN3605, CN3611, CN3902) 4two sc
8、rews (BV3) 8D-VIDEO board 3screw (BVTP3 8) (AEP, Russian, Ukrainian, UK and Chinese models) (US and Canadian models) 1two clamps 1clamp 7bracket (HDMI) 6screw (BVTP3 8) 5seven screws (B3 6) Ver. 1.2 STR-DA5300ES 22 3-6.FRONT PANEL SECTION 3-7.S-VIDEO BOARD AND A-VIDEO BOARD 3connector (CNP53) 7two s
9、crews (BVTP3 8) 6five screws (BVTP3 8) 9front panel section 8 5connector (CN6904) 4connector (CN606) 1two clamps 2clamp 5two connectors (CN6518, CN6519) 3four screws (BVTP3 8) 4S-VIDEO board 8A-VIDEO board 1connector (CN6904) 2wire (flat type) (21 core) (S-VIDEO board (CN6903), A-VIDEO board (CN6509
10、) 6seven screws (BVTP3 8) 7screw (BVTP3 8) STR-DA5300ES 23 3-8.FLI-1.8REG BOARD AND ANALOG BOARD 5connector (CN608) 6connector (CN606) 7two connectors (CN601, CN1003) 3two screws (BVTP3 8) qascrew (BVTP3 8) 4bracket (WB) qfANALOG board 9screw (B3 6) qdwire (flat type) (9 core) (US and Canadian model
11、s) (CN609), wire (flat type) (11 core) (AEP, Russian, Ukrainian, UK and Chinese models) (CN603) 8connector (CN727) qsbracket (side) (US and Canadian models) 2FLI-1.8REG board 1screws (BVTP3 8) q; q;six screws (BVTP3 8) Ver. 1.2 STR-DA5300ES 24 3-9.POWER TRANS FORMER (T001), E-VOL BOARD AND MAIN BOAR
12、D 2connector (CNP02) 7CONNECTOR 2 board 9CONNECTOR 1 board 4four screws (BVTT4 8) q;wire (E-VOL board (CN1209), MAIN board (CN1205) 1connector (CN1402) 3two connectors (CN1403, CN1408) 5power transformer (T001) qstwo screws (BVTP3 8) qftwo screws (BVTP3 8) qjtwo screws (supllied with J1499) qhE-VOL
13、board qgbracket (SS) qgbracket (SS) wstwo wires (CN1001, CN1004) w;three screws (BV/ring) qlfour screws (BVTP3 8) wafive screws (BVTP3 8) wdMAIN board 8two connectors (CN1207, CN1209) 6two connectors (CN1205, CN1206) qdtwo connectors (CN1203, CN1204) qawire (E-VOL board (CN1208), MAIN board (CN1206)
14、 qkfeeder fixed screw STR-DA5300ES 25 3-10. HEAT SINK SECTION 5connector (CN1405) 6four screws (BVTP3 8) 6three screws (BVTP3 8) 7heart sink section 2CONNECTOR 2 board 4CONNECTOR 1 board 3two connectors (CN1207, CN1209) 1two connectors (CN1205, CN1206) 26 STR-DA5300ES color pattern generator DMPORT
15、check jig (Part No.: J-2501-309-A) J001 AF oscillator set TV monitor FL/FR speaker A-VIDEO board CN6505 MAIN board TM4002 A-VIDEO board J6203 SECTION 4 TEST MODE MEMORY CLEARING MODE All preset contents are cleared when this mode is activated. Use this mode before returning the product to clients up
16、on completion of repair. Procedure: 1. While pressing the TONE MODE and DMPORT buttons, press the POWER button to turn on the main power. 2. The message “MEMORY CLEARING*” appears and the memories are reset to the default values. 3. When done, the message “MEMORY CLEARED*” appears. FLUORESCENT INDIC
17、ATOR TUBE PATTERN CHECK MODE All fluorescent segments are tested. When this test is activated, all segments turn on at the same time, then each segment turns on one after another. Procedure: 1. While pressing the MOVIE and DMPORT buttons, press the POWER button to turn on the main power. 2. All segm
18、ents and all LEDs turn on. SOUND FIELD CLEAR MODE The preset sound field is cleared when this mode is activated. Use this mode before returning the product to clients upon completion of repair. Procedure: 1. While pressing the MUSIC button, press the POWER button to turn on the main power. 2. The me
19、ssage “S. F. Initialize” appears and initialization is performed. TUNER AM STEP CHANGE (9 kHz/10 kHz) MODE (US and Canadian models only) Either the 9 kHz step or 10 kHz step can be selected for the AM channel step. Procedure: 1.Press the POWER button to turn on the main power. 2.Turn the INPUT SELEC
20、TOR dial to select the “AM”. 3.Press the POWER button to turn off the main power. 4.While pressing the TUNING MODE button, press the POWER button to turn on the main power. 5.Either the message “AM 9kHz Step” or “AM 10kHz Step” appears, select the desired step. COMMAND MODE CHANGE MODE The command m
21、ode of the remote-commander which this set receives can be changed. Procedure: 1. While pressing the 2CH/A. DIRECT button, press the POWER button to turn on the main power. 2. Either the message “COMMAND MODE AV1” or “COMMAND MODE AV2” appears. Select the desired mode. SF LOCK ON/OFF CHANGE MODE Pro
22、cedure: 1. While pressing the MUSIC and DMPORT buttons, press the POWER button to turn on the main power. 2. Either the message “SF LOCK OFF” or “SF LOCK ON” appears. XM FACTORY TEST MODE (US and Canadian models only) Mode to confirm operation of XM. Doing display of ID of XM antenna and output of a
23、udio signal that XM antenna generates, it is confirmed that there are no problems in the communication of the XM antenna and the tranmission of the audio signal. Procedure: 1. The XM antenna was connected, while pressing the TUNING MODE and MOVIE buttons, press the POWER button to turn on the main p
24、ower. 2. Whenever the DISPLAY button is pressed, the output of the audio signal of 1 kHz L/R, 20 Hz L/R, 5 kHz L/R, muting, 1 kHz L and 1 kHz R are switched. SIRIUS FACTORY TEST MODE (US and Canadian models only) Mode to confirm operation of SIRIUS. Doing display of ID of SIRIUS antenna and output o
25、f audio signal that SIRIUS antenna generates, it is confirmed that there are no problems in the communication of the SIRIUS antenna and the transmission of the audio signal. Procedure: 1. The SIRIUS antenna was connected, while pressing the TUNING MODE and A.F.D. buttons, press the POWER button to t
26、urn on the main power. 2. Whenever the DISPLAY button is pressed, the output of the audio signal of 1 kHz L/R, 20 Hz L/R, 5 kHz L/R, muting, 1 kHz L and 1 kHz R are switched. DIGITAL MEDIA PORT TEST Procedure: 1. Connect the DMPORT check jig (P/N: J-2501-309-A) with the DMPORT jack (CN6505) on the A
27、-VIDEO board. 2. While pressing the A.F.D. and DMPORT buttons, press the POWER button to turn on the main power. 3. The message “DMPORT OK.” appears on the fluorescent indicator tube and enter the digital media port test mode (Confirmation of communication line). When “NO DETECT”, “UART NG” and “UAR
28、T TO” are displayed on the fluorescent indicator tube, confirm the connection of the DMPORT check jig, and enter the mode again. Each time the button on the remote commander is pressed, the connect check and adaptor version check are switched. Press the . button on the remote commander, connected co
29、nfirmation of the DMPORT check jig is done again. 4. To a pin-jack of the DMPORT check jig input information relevant to audio signal (sine-wave 1.0 Vrms) and composite video signal (white 100% 1.0 Vp-p, color bar, etc.). 5. Confirm the output of speakers and monitor TV (Confirmation of analog signa
30、l). 6. To exit from this mode, press the x button on the remote commander. 27 STR-DA5300ES HISTORY MODE The state that the set is used is memorized. Procedure: 1.While pressing the MUSIC and MEMORY/ENTER buttons, press the POWER button to turn on the power and “HIS- TORY MODE” is displayed. 2.Each t
31、ime the M m key of remote commander is pressed, the item is switched in order as follows. ItemsDisplay Number of protector is generatedPRCT COUNT: XXX Total use timeTTL_TIME: XXXXH XXM Sound field settingXXXXXXXXXXXXXXXX Input when protect is detectedINPUT: XXXXXXXXXX Input mode settingINMODE: XXXXX
32、XXXXXXX Input mode under lick stateDSEL: XXXXXXXXXXXXXXX Stream under inputSTREAM: XXXXXXX Channel informationCONFIG:XXXXXXX State of headphoneHEAD PHONES: XXX VolumeVOL: XXXdB EQ setting value BASS: XXXdB TREB: XXXdB Lv FL/FR XXXX/XXXX Level collection valueLv SL/SR XXXX/XXXX each channelLv CT/SW X
33、XXX/XXXX Lv BL/BR XXXX/XXXX Total time of power onTTL_P_ON: XXXXH XXM 28 STR-DA5300ES SPECIAL MENU MODE Procedure: 1. Press the POWER button to turn on the main power, then while pressing the TONE MODE button, press the A.F.D., 2CH/A. DIRECT, MUSIC, MOVIE button in order, the message “MENU SPECIALIZ
34、ED!” appears. 2. Press the M m button of the remote commander, the message “” appears. 3. Press the , button of the remote commander, the item is appears. 4. Each time the M m button of the remote commander is pressed, the item is switched in order as follows. Some items can change the content. Disp
35、lay the cursor by pressing the , button of the remote commander, and changing the content by pressing the M m button of the remote commander, and fix the content by pressing the button of the remote commander when you want to change the content of the item. 5. To release from this mode, while pressi
36、ng the TONE MODE button, press the A.F.D., 2CH/A. DIRECT, MUSIC, MOVIE button in order again, the message “MENU SPECIALIZED OFF” appears. ItemsDisplayRemark Video factory menuMenu mode to enter video calibration menu and DDR access check menu If the ENTER button of the remote commander is pressed, e
37、ntering the menu, and operating two the following menu become possible Video calibrationV.CALIBRATION START?Procedure: (Video factory menu)1.“DVD” is selected by using INPUT SELECTOR dial. 2.Connect a color pattern generator to the COMPONENT VIDEO ASSIGNABLE (INPUT ONLY) DVD/BD IN jack (J6002) on th
38、e A- VIDEO board, DVD/BD VIDEO IN jack (J6201) on the A-VIDEO board, DVD/BD S VIDEO IN jack (J6901) on the S-VIDEO board and EXT VIDEO IN jack (J6904). 3.Input 100% color bars signal from the color pattern generator. 4.Menu that measures individual difference of hardness by automatic operation in pr
39、essing the ENTER button of the remote commander, and corrects reference value. In a measurement once, only one of NTSC/PAL/HD can be measured “Check XXXX V-IN” at display: Video signal necessary for the measurement while measuring it last time was not detected and it became an error Confirm the inpu
40、t of the video of the terminal connection etc. , and measure the ENTER button of the remote commander again pressing DDR access checkDDR CHECK XX secXX: Time to do access check on DDR (for design evaluation) (Video factory menu) Auto cal mic testSPEAKER OUT XXXXXXXXXX: Selection of speaker output au
41、dio SOURCE: nomally mode, MIC: mode that output audio from mic from speaker FL display fonts testFL FONT 0 x * = X*: 20 to FE, X: character FL display testALL ONEach time DISPLAY button to change as follows all on t test pattern 1 t test pattern 2 t all off t all on HDCP key readHDCP KEY READ XXXXXX
42、: ON or OFF DSP SRAM checkXX: OK or NG r ENTER button of the remoteOK: success access SRAM, NG: fail access to SRAM commander SRAM1 XX SRAM2 XX FAROUDJA updateFAROUDJA UPDATE XXXXXX: ON or OFF Model version display# * vX. XX #: Model *: Destination X.XX: System controller software version : Sum valu
43、e of flash memory in the system controller Video Ucom version displayVideo Ucom Ver X. XXX.XX: Video system controller software version FAROUDJA version displayFAROUDJA Ver X. XXX.XX: Video Processor software version GUI CG-ROM version displayGUI CGROM Ver X. XXX.XX: CG-ROM software version DSP Ucom
44、 version displayDSP Ucom Ver X. XXX.XX: DSP controller version DSP serial flash version displayDSP SFLASH Ver X. XXX.XX: Serial flash software version DSP parallel flash version displayDSP PFLASH Ver X. XXX.XX: DSP parallel flash version DSP haltDSP HALT XXXXXX: ON or OFF DSP RAM*=XXXXXXXXMode that
45、refers to internal RAM of DSP (for design evaluation) 29 STR-DA5300ES ItemsDisplayRemark Super resetSUPER RESET XXXNot used for the servicing If super reset is performed, “up convert signal level adjustment” will also be initialized When EEPROM initialization is required, perform the “memory clearin
46、g mode” RAM watch menuXXXXXX: For monitor of various internal RAM (for design evaluation) EERROM debugEEPROM * XX*: EEPROM address, XX: EEPROM data Protector on/offPROTECTOR ON/OFF XXXXXX: ON or OFF Model/destination changeMODEL # * * * * X X#: Model, *: Destination, XX: At or fx Audio swapSWAP XXXX
47、XXXXXXXSwitching with M m button of the remote commander Decoder selectDECODER SEL XXXXXXXX: AUTO, LEGACY, DDPLUS, TRUEHD, DTSEXP, MP3SUR (for debug) Volume value display (FL/FR)FL* FR XXXX*: Front L-ch volume value, XXXX: Front R-ch volume value Volume value display (SL/SR)SL* SR XXXX*: Surround L-
48、ch volume value, XXXX: Surround R-ch volume value Volume value display (CT/SW)CT* SW XXXX*: Center volume value, XXXX: Sub woofer volume value Volume value display (SBL/SBR)SBL* SBR XXXX*: Surround back L-ch volume value, XXXX: Surround back R-ch volume value DAC mute information disclosure 1 DAC MU
49、TE U XXXXXXXXDisplay of module information to demand muting in system controller (for design evaluation) DAC mute information disclosure 2 DAC MUTE L XXXXXXXXDisplay of module information to demand muting in system controller (for design evaluation) 2nd volume value display2nd VOLUME XXXXXX: 2nd room volume value (00 to ) FL display duty changeDARK OUT DUTY XXX%XXX: Duty value of FL display (0% to 100%) DMPORT debugDMP KEY DEBUG XXXXXX: ON or OFF (for debug) Bus overflow debug HA
免费区 
