Sony-STRDA7100ES-rec-sm 电路图 维修手册.pdf

《Sony-STRDA7100ES-rec-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Sony-STRDA7100ES-rec-sm 电路图 维修手册.pdf（240页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL FM STEREO FM/AM RECEIVER US Model Canadian Model AEP Model Taiwan Model Korean Model Chinese Model STR-DA7100ES Ver. 1.3 2005.12 SPECIFICATIONS 9-879-764-04 2005L05-1 2005.12 Sony Corporation Home Audio Division Published by Sony Engineering Corporation Continued on next page This rec

2、eiver incorporates Dolby* Digital and Pro Logic Surround and the DTS* Digital Surround System. *Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic”, “Surround EX”, and the double-D symbol are trademarks of Dolby Laboratories. * Manufactured under license from Digital Theater Sys

3、tems, Inc. U.S. Pat. Nos. 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535 and other U.S. and world-wide patents issued and pending. “DTS”, “DTS-ES”, “Neo:6”, and “DTS 96/24” are trademarks of Digital Theater Systems, Inc. Copyright 1996, 2003 Digital Theater Systems, Inc. All Rights

4、 Reserved. AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION: (Models of area code US only) With 8 ohm loads, both channels driven, from 20 20,000 Hz; rated 170 watts per channel minimum RMS power, with no more than 0.15% total harmonic distortion from 250 milliwatts to rated out

5、put. Amplifier section Models of area code US, CND, TW: POWER OUTPUT Rated Power Output at Stereo Mode1) (8 ohms 20 Hz 20 kHz, THD 0.15%): 170 W + 170 W Reference Power Output at Stereo Mode (4 ohms 20 Hz 20 kHz, THD 0.15%): 170 W + 170 W Reference Power Output (8 ohms 20 Hz 20 kHz, THD 0.15%) FRONT

6、2): 170 W + 170 W CENTER2): 170 W SURR2): 170 W + 170 W SURR BACK2): 170 W + 170 W Reference Power Output (4 ohms 20 Hz 20 kHz, THD 0.15%) FRONT2): 170 W + 170 W CENTER2): 170 W SURR2): 170 W + 170 W SURR BACK2): 170 W + 170 W Models of area code AEP, KR, CH: POWER OUTPUT Rated Power Output in Stere

7、o Mode1) (8 ohms 1 kHz, THD 0.7%): 170 W + 170 W Reference Power Output in Stereo Mode (4 ohms 1 kHz, THD 0.7%): 170 W + 170 W Reference Power Output (8 ohms 1 kHz, THD 0.7%): FRONT2): 170 W + 170 W CENTER2): 170 W SURR2): 170 W + 170 W SURR BACK2): 170 W + 170 W RadioFans.CN 收音机爱 好者资料库 2 STR-DA7100

8、ES ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT! LES COMPOSANTS IDENTIFIS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONT CRITIQUES POUR LA SCURIT DE FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS QUE PAR DES PICES SONY DONT LES NUMROS SONT DONNS DANS CE MANUEL OU DANS LE

9、S SUPPLMENTS PUBLIS PAR SONY. SAFETY-RELATED COMPONENT WARNING! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN

10、SUPPLEMENTS PUBLISHED BY SONY. Abbreviation CH: Chinese model CND: Canadian model KR: Korean model TW : Taiwan model Reference Power Output (4 ohms 1 kHz, THD 0.7%): FRONT2): 170 W + 170 W CENTER2): 170 W SURR2): 170 W + 170 W SURR BACK2): 170 W + 170 W 1)Depending on the sound field settings and th

11、e source, there may be no sound output. 2)Measured under the following conditions: Frequency response Inputs (Analog) Inputs (Digital) Outputs EQUALIZER FM tuner section Tuning range87.5 - 108.0 MHz AntennaFM wire antenna Antenna terminals75 ohms, unbalanced Sensitivity Mono:18.3 dBf, 2.2 V/75 ohms

12、Stereo:38.3 dBf, 22.5 V/75 ohms Usable sensitivity 11.2 dBf, 1 V/75 ohms S/N Mono:76 dB Stereo:70 dB Harmonic distortion at 1 kHz Mono:0.3% Stereo:0.5% Separation45 dB at 1 kHz Frequency response 30 Hz 15 kHz, +0.5/2 dB Selectivity60 dB at 400 kHz AM tuner section Tuning range Models of area code US

13、, CND: 530 1,710 kHz3) (With 10-kHz tuning scale) 531 1,710 kHz3) (With 9-kHz tuning scale) Area codePower requirements US, CND120 V AC, 60 Hz TW110 V AC, 60 Hz AEP230 V AC, 50/60 Hz KR230 V AC, 60 Hz PHONORIAA equalization curve 0.5 dB Power Amp Block10 Hz 50 kHz 3 dB (8 ohms) PHONOSensitivity: 2.5

14、mV Impedance: 50kohms S/N: 86dB (A, 20 kHz LPF) MULTI CHANNEL INPUT1/2, SA-CD/CD, TAPE, MD/DAT, DVD, TV/SAT, VIDEO1/2/3 Sensitivity: 150mV Impedance: 50kohms S/N: 96dB (A, 20 kHz LPF) CH230 V AC, 50 Hz SA-CD/CD, DVD (Coaxial) Impedance: 75ohms S/N: 96dB (A, 20 kHz LPF) SA-CD/CD, DVD, TV/SAT, MD/DAT,

15、 VIDEO 3 (Optical) S/N: 96 dB (A, 20 kHz LPF) TAPE, MD/DAT (REC OUT), VIDEO1/2 (AUDIO OUT) Voltage:150mV Impedance: 10kohms FRONT L/R, CENTER, SURROUND L/R, SURROUND BACK L/R, SUB WOOFER Voltage: 2V Impedance: 1kohms Gain levels10 dB, 1 dB step Models of other area codes: 531 1,602 kHz (With 9-kHz t

16、uning scale) AntennaLoop antenna Usable sensitivity50 dB /m (at 1,000 kHz or 999 kHz) S/N54 dB (at 50 mV/m) Harmonic distortion 0.5% (50 mV/m, 400 Hz) Selectivity At 9 kHz:35 dB At 10 kHz:40 dB 3)You can change the AM tuning scale to either 9 kHz or 10 kHz. After tuning in any AM station, turn off t

17、he receiver. While holding down PRESET TUNING + or TUNING +, press ?/1. All preset stations will be erased when you change the tuning scale. To reset the scale to 10 kHz (or 9 kHz), repeat the procedure. Video section Inputs/Outputs Video:1 Vp-p, 75 ohms S-video:Y: 1 Vp-p, 75 ohms C: 0.286 Vp-p, 75

18、ohms COMPONENT VIDEO: Y: 1 Vp-p, 75 ohms PB/CB/B-Y: 0.7 Vp-p, 75 ohms PR/CR/R-Y: 0.7 Vp-p, 75 ohms 80 MHz HD Pass Through (When PROGRESSIVE OUT is set to “OFF”) i.LINK section Pin4 pins Transmission speedS200 (Maximum data transmission speed 200 Mbps) Transmission protocol A/M transmission protocol

19、Format (input)Super Audio CD* (DSD PLAIN) 2 channel linear PCM (IEC-60958-3) Sampling frequency: 44.1 kHz * Conforms to the copy protection technology of DTLA (Revision 1.3). General Power requirements Power consumption Power consumption (during standby mode) 1 W AC outlets Dimensions430 175 470 mm

20、(17 7 18 5/8 in.) including projecting parts and controls Mass (Approx.)23.5 kg (51 lb. 13 oz.) Supplied accessories FM wire antenna (1) AM loop antenna (1) AC power cord (1) Remote commander RM-AAE003 (1) LR6 (size-AA) batteries (3) Remote commander RM-US106A (1) R6 (size-AA) batteries (2) Design a

21、nd specifications are subject to change without notice. Area codePower requirements US, CND120 V AC, 60 Hz AEP230 V AC, 50/60 Hz TW110 V AC, 60 Hz KR220 V AC, 60 Hz Area codePower consumption US, AEP, TW, KR, CH 250 W CND300 VA Area codeAC outlets US, CND2 switched, 120 W/1A MAX AEP1 switched, 100 W

22、 MAX TW, KR, CH (no AC outlet) CH220 V AC, 50 Hz Ver 1.2 RadioFans.CN 收音机爱 好者资料库 3 STR-DA7100ES Notes on chip component replacement Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor may be damaged by heat. SAFETY CHECK-OUT After correcting the original ser

23、vice problem, perform the following safety check before releasing the set to the customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE TEST The AC leakage from any exposed metal part

24、to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes.). Leakage current can be measured by any one of three methods. 1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufactu

25、rers instructions to use these instruments. 2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indication is 0.75 V, so analog meter

26、s must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suitable. (See Fig. A) Fig. A.Using an AC voltmeter to check AC leakage. 1.5 k0.15 F AC voltmeter

27、 (0.75 V) To Exposed Metal Parts on Set Earth Ground RadioFans.CN 收音机爱 好者资料库 4 STR-DA7100ES TABLE OF CONTENTS 1.SERVICING NOTES.5 2.GENERAL. 13 3.DISASSEMBLY 3-1.Disassembly Flow . 18 3-2.Case . 18 3-3.Front Panel Assy. 19 3-4.Bottom Plate . 20 3-5.D-AMP Board Block. 20 3-6.DC Fan Block . 21 3-7.Bac

28、k Panel Block . 21 3-8.Mother COM Board . 22 4.TEST MODE. 23 5.ELECTRICAL ADJUSTMENTS. 27 6.DIAGRAMS 6-1.Block Diagram Audio Input Section . 61 6-2.Block Diagram Control Section . 62 6-3.Block Diagram i.LINK Section . 63 6-4.Block Diagram DSP Section . 64 6-5.Block Diagram Digital Audio Section . 65

29、 6-6.Block Diagram Audio Output Section . 66 6-7.Block Diagram Power AMP Section . 67 6-8.Block Diagram SUB Section . 68 6-9.Block Diagram Video Input Section . 69 6-10. Block Diagram CIS Display Section . 70 6-11. Block Diagram HDMI Receiver Section . 71 6-12. Block Diagram HDMI Trasceiver Section

30、. 72 6-13. Block Diagram Power Supply Section . 73 6-14. Printed Wiring Board Digital Board (Component Side) . 74 6-15. Printed Wiring Board Digital Board (Conductor Side) . 75 6-16. Schematic Diagram Digital Board (1/8) . 76 6-17. Schematic Diagram Digital Board (2/8) . 77 6-18. Schematic Diagram D

31、igital Board (3/8) . 78 6-19. Schematic Diagram Digital Board (4/8) . 79 6-20. Schematic Diagram Digital Board (5/8) . 80 6-21. Schematic Diagram Digital Board (6/8) . 81 6-22. Schematic Diagram Digital Board (7/8) . 82 6-23. Schematic Diagram Digital Board (8/8) . 83 6-24. Printed Wiring Board DSP

32、Board . 84 6-25. Schematic Diagram DSP Board . 85 6-26. Printed Wiring Board Analog Board (Component Side) . 86 6-27. Printed Wiring Board Analog Board (Conductor Side) . 87 6-28. Schematic Diagram Analog Board (1/4) . 88 6-29. Schematic Diagram Analog Board (2/4) . 89 6-30. Schematic Diagram Analog

33、 Board (3/4) . 90 6-31. Schematic Diagram Analog Board (4/4) . 91 6-32. Schematic Diagram Ilink Section (1/10) . 92 6-33. Schematic Diagram Ilink Section (2/10) . 93 6-34. Schematic Diagram Ilink Section (3/10) . 94 6-35. Schematic Diagram Ilink Section Board (4/10) . 95 6-36. Schematic Diagram Ilin

34、k Section (5/10) . 96 6-37. Schematic Diagram Ilink Section (6/10) . 97 6-38. Schematic Diagram Ilink Section (7/10) . 98 6-39. Schematic Diagram Ilink Section (8/10) . 99 6-40. Schematic Diagram Ilink Section (9/10) .100 6-41. Schematic Diagram Ilink Section (10/10) .101 6-42. Printed Wiring Board

35、Ilink Board (Component Side) . 102 6-43. Printed Wiring Board ILINK Board (Conductor Side) . 103 6-44. Printed Wiring Board Conect Boards .104 6-45. Schematic Diagram Video Board (1/3) .105 6-46. Schematic Diagram Video Board (2/3) .106 6-47. Schematic Diagram Video Board (3/3) .107 6-48. Printed Wi

36、ring Board Video Board (Component Side) .108 6-49. Printed Wiring Board Video Board (Conductor Side) .109 6-50. Printed Wiring Board S-video Board (Component Side) .110 6-51. PPrinted Wiring Board S-video Board (Conductor Side) .111 6-52. Printed Wiring Board Video3 Board .112 6-53. Schematic Diagra

37、m S-video Section . 113 6-54. Printed Wiring Board Mother COM Board (Component Side) . 114 6-55. Printed Wiring Board Mother COM Board (Conductor Side) . 115 6-56. Schematic Diagram Mother COM Board (1/3) . 116 6-57. Schematic Diagram Mother COM Board (2/3) . 117 6-58. Schematic Diagram Mother COM B

38、oard (3/3) . 118 6-59. Printed Wiring Board D-AMP Board (Component Side) . 119 6-60. Printed Wiring Board D-AMP Board (Conductor Side) . 120 6-61. Schematic Diagram D-AMP Board (1/4) . 121 6-62. Schematic Diagram D-AMP Board (2/4) . 122 6-63. Schematic Diagram D-AMP Board (3/4) . 123 6-64. Schematic

39、 Diagram D-AMP Board (4/4) . 124 6-65. Printed Wiring Board Filter-l Boards . 125 6-66. Schematic Diagram Filter-l Board . 126 6-67. Printed Wiring Board Filter-R Boards . 127 6-68. Schematic Diagram Filter-R Board . 128 6-69. Printed Wiring Board SP-Term COM Board (Component Side) . 129 6-70. Print

40、ed Wiring Board SP-Term Com Board (Conductor Side) . 130 6-71. Schematic Diagram SP-Term COM Board (1/3) . 131 6-72. Schematic Diagram SP-Term COM Board (2/3) . 132 6-73. Schematic Diagram SP-Term COM Board (3/3) . 133 6-74. Printed Wiring Board CIS Board (Component Side) . 134 6-75. Printed Wiring

41、Board CIS Board (Conductor Side) . 135 6-76. Schematic Diagram CIS Board . 136 6-77. Printed Wiring Board FL Board . 137 6-78. Schematic Diagram FL Board . 138 6-79. Printed Wiring Board Panel Section . 139 6-80. Schematic Diagram Panel Section . 140 6-81. Printed Wiring Board Regulator Sections . 141 6-82. Schematic Diagram Regulator Sections . 142 6-83. Printed Wiring Board DC DIF Board . 143 6-84. Schematic Diagram DC DIF Boards . 144 6-85. Printed Wiring Board AC DIF Section .