《Sony-STRSE581-rec-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Sony-STRSE581-rec-sm 电路图 维修手册.pdf（28页珍藏版）》请在收音机爱好者资料库上搜索。
1、STR-SE581 US ModelSERVICE MANUAL FM STEREO/FM-AM RECEIVER MICROFILM Manufactured under license from Dolby Laboratories Licensing Corporation. “Dolby” “Pro Logic” and the double-D symbol a are trademarks of Dolby Laboratories Licensing Corporation. SPECIFICATIONS Continued on next page Audio power sp
2、ecifications POWER OUTPUT AND TOTAL HARMONIC DISTORTION With 8 load, both channels driven, from 40 - 20,000 Hz, rated 100 watts per channel minimum RMS power, with no more than 0.5% total harmonic distortion from 250 milliwatts to rated output. Amplifier section Stereo mode(8 at 40 Hz - 20 kHz less
3、than 0.5% total harmonic distortion) 100 W + 100 W Surround mode(8 at 1 kHz, THD 0.5%) Front: 100 W/ch Center: (Pro Logic Mode) 100 W Rear: 50 W/ch 5.1/DVD INPUT* mode(8 at 1 kHz, THD 0.8%) Front: 100 W/ch Center: 100 W Rear: 50 W/ch Frequency responsePHONO: RIAA equalization curve 0.5 dB TV/DBS, CD
4、, TAPE/MD, VIDEO, 5.1/DVD INPUT 10 Hz - 50 kHz 1 dB Inputs Sensitivity Impedance S/N (weighting network, input level) PHONO (MM) 2.5 mV50 Kilohms 72 dB* (A, 2.5 mV) CD400 mV TAPE/MD,250 mV 82 dB* TV/DBS,50 Kilohms (A, 150 mV) VIDEO, 5.1/ DVD INPUT* *78 IHF OutputsTAPE/MD REC OUT: Voltage: 150 mV, Im
5、pedance: 10 k VIDEO AUDIO OUT: Voltage: 150 mV, Impedance: 10 k WOOFER: Voltage: 2 V, Impedance: 10 k PHONES: Accepts low and high impedance headphones MutingFull mute BASS BOOST+10 dB at 70 Hz TONE8 dB at 100 Hz and 10 kHz FM tuner section Tuning range87.5 - 108.0 MHz Antenna terminals75 ohms, unba
6、lanced 300 ohms, balanced SensitivityMono: 18.3 dBf, 4.5 V Stereo: 38.3 dBf, 45 V Usable sensitivity11.2 dBf, 2 V (IHF) S/NMono: 76 dB Stereo: 70 dB Harmonic distortion at 1 kHz Mono: 0.3% Stereo: 0.59% Separation45 dB at 1 kHz +0.5 Frequency response30 Hz 15 kHz2 dB Selectivity60 dB at 400 kHz AM t
7、uner section Tuning range531 1710 kHz AntennaLoop antenna Usable sensitivity50 dB/m (at 1,000 kHz) S/N54 dB (at 50 mV/m) RadioFans.CN 收音机爱 好者资料库 2 1.GENERAL3 2.TEST MODE5 3.DIAGRAMS 3-1.Circuit Boards Location 6 3-2.Printed Wiring Board Display Section 7 3-3.Schematic Diagram Display Section 9 3-4.P
8、rinted Wiring Board Volume/Video Section 11 3-5.Schematic Diagram Volume/Video Section 13 3-6.Printed Wiring Board Main Section 15 3-7.Schematic Diagram Main Section (1/3) 17 3-8.Printed Wiring Board SP-SW, Power Section 19 3-9.Schematic Diagram Main Section (2/3), SP-SW 21 3-10. Schematic Diagram M
9、ain Section (3/3), Power 23 3-11. IC Pin Function 25 3-12. IC Block Diagrams 27 4.EXPLODED VIEWS 4-1.Front Panel Section 29 4-2.Chassis Section30 5.ELECTRICAL PARTS LIST31 TABLE OF CONTENTS Harmonic distortion0.5% (50 mV/m, 400 kHz) SelectivityAt 10 kHz: 40 dB General SystemTuner section: PLL quartz
10、-locked digital synthesizer system Preamplifier section: Low-noise NF type equalizer Power amplifier section: Pure-complementary SEPP Power requirements120 V AC, 60 Hz Power consumption230 W AC outlets2 switched, total 120 W/1A Max Dimensions17 5 7/8 11 5/8 inches (430 145 295 mm) Mass (Approx.)16 I
11、B 15 oz (7.7 kg) Supplied accessoriesFM wire antenna (1) AM loop antenna (1) Remote controller (remote) (1) Size AA (R6) batteries (2) Design and specifications are subject to change without notice. SAFETY-RELATED COMPONENT WARNING! COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH MARK ! ON THE S
12、CHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. After correcting the original service problem, perform the following safety checks before releasing
13、the set to the customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal p
14、art having a return to chassis, must not exceed 0.5 mA (500 microampers). Leakage current can be measured by any one of three methods. 1.A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers instructions to use these instruments. 2.A battery-operated AC millia
15、mmeter. The Data Precision 245 digital multimeter is suitable for this job. 3.Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indication is 0.75 V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Tr
16、d are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2V AC range are suitable. (See Fig. A) SAFETY CHECK-OUT To Exposed Metal Parts on Set 0.15 F 1.5 k AC Voltmeter (0.75 V) Earth Ground Fig. A. Using an AC voltmeter to check AC leakage. Radio
17、Fans.CN 收音机爱 好者资料库 3 SECTION 1 GENERAL LOCATION AND FUNCTION OF CONTROLS FRONT PANEL 1POWER switch (I/u) 2CENTER LEVEL +, buttons 3PRO LOGIC indicator 4C. STUDIO indicator 5HALL indicator 6MASTER VOLUME control 7BALANCE control 8TREBLE control 9BASS control 0BASS BOOST button/indicator !SURROUND ON/
18、OFF button !MODE button !SET UP button !EFECT/DELAY TIME button !5.1/DVD INPUT button !TAPE/MD FUNCTION button !TV/DBS FUNCTION button !VIDEO FUNCTION button !PHONO FUNCTION button TUNER FUNCTION button CD FUNCTION button DIRECT button SHIFT button Numeric buttons PRESET TUNING +, buttons MEMORY but
19、ton AM button FM button FM MODE button #TUNING +, buttons #PHONES jack #SPEAKERS A/B buttons #REAR LEVEL +, buttons 12# 3 4 5! ! ! !6 # # # 78! ! !9! RadioFans.CN 收音机爱 好者资料库 4 REAR PANEL 1SIGNAL GND 25.1/DVD INPUT (FRONT/REAR) 3WOOFER 4ANTENNA (AM/FM) 5PHONO 6CD 7TAPE/MD 8TV/DBS 9VIDEO 0SURROUND SPE
20、AKERS (REAR) !FRONT SPEAKERS !AC OUTLET !AC power code !5.1/DVD INPUT (CENTER) !5.1/DVD INPUT (WOOFER) !SURROUND SPEAKERS (CENTER) 12 !? !?3!? 45 6 7 8 90!?!?!? 5 6 SECTION 2 TEST MODE INITIALIZATION MODE *All preset contents are cleared when this mode is activated. Use this mode before returning th
21、e product to clients upon completion of repair. *Procedure: While depressing the VIDEO, TAPE/MD and the CD buttons simultaneously, press the power I/u button to turn on the main power. The message INITIAL appears and initialization is performed. FLUORESCENT INDICATOR TUBE TEST MODE *All fluorescent
22、segments are tested. When this test is activated, all segments turn on at the same time, then each segment turns on one after another. *Procedure: While depressing the CD and the TAPE/MD buttons simultaneously, press the power I/u button to turn on the main power. All segments turn on at the same ti
23、me, then each segment turns on one after another. The message FINISH appears when this test is complete. AM CHANNEL STEP 9 kHz/10 kHz SELECTION MODE *Either the 9 kHz step or 10 kHz step can be selected for the AM channel step. *Procedure: Set the FUNCTION to AM. Turn off the main power. While depre
24、ssing the TUNING+ button, press the power I/u button to turn on the main power. Either the message 9k STEP or 10k STEP appears. Select the desired step. REAR SPEAKER GAIN UP MODE *The rear speaker gain can be set to either NORMAL or GAIN UP. *Procedure: While depressing the -SURROUND button, press t
25、he power I/ u button to turn on the main power. Either the message NORMAL or GAIN UP appears. When the product enters this mode again, the other gain appears. Select the desired gain. SECTION 3 DIAGRAMS 3-1.CIRCUIT BOARDS LOCATION Waveforms For schematic diagrams. Note: All capacitors are in F unles
26、s otherwise noted. pF: F 50 WV or less are not indicated except for electrolytics and tantalums. All resistors are in and 1/4 W or less unless otherwise specified. %: indicates tolerance. : internal component. 2 : nonflammable resistor. 1 : fusible resistor. C : panel designation. U : B+ Line. V : B
27、 Line. Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. No mark : FM Voltages are taken with a VOM (Input impedance 10 M). Voltage variations may be noted due to normal production tolerances. Waveforms are taken with a oscilloscope. Circled numbers refer to
28、waveforms. Signal path. F: FM THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this necessary note is printed in each block.) For printed wiring boards. Note: X : parts extracted from the component side. b : Pattern from the side which enables seeing. SP-SW BOARD
29、 PRIMARY BOARD SECONDARY BOARD STANDBY BOARD MAIN BOARD VIDEO BOARD SWITCH BOARD VOLUME BOARD VR-TONE BOARD KEY BOARD DISPLAY BOARD Note: The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. 1 IC300 (OSC) 2 IC201 # (X1) 8MHz
30、 4.19MHz 4.75Vp-p 5.3Vp-p STR-SE581 7 8 3-2.PRINTED WIRING BOARD DISPLAY SECTION Ref. No.Location D201C-3 D202C-3 D203C-3 D204B-13 D211C-9 D213C-9 D214C-9 D231C-1 D234C-2 D235C-9 D236C-10 D237C-11 Semiconductor Location Ref. No.Location D239C-3 D240C-2 IC201D-6 IC202B-2 IC203D-11 Q201B-13 Q202B-12 Q
31、231C-1 Q232E-3 12 A B C D E F G H 3456789101112131415 DISPLAY BOARD KEY BOARD F TO VOLUME BOARD CNP202 J TO MAIN BOARD CNS204 1-665-280- 11 (12) 110 E 1 9 (5.1 INPUT) 1 80 24 25 65 64 40 41 IC201 1-665-281- 11 (12) (HALL)(C.STUDIO)(PRO LOGIC) (REMOTO SEUSOR) 41 PRESET TUNING MEMORY DIRECT VIDEO TV/D
32、BS CDTUNERPHONO TAPE/MD EFFECT DELAY TIME SET UP 5.1/DVD INPUT MODE SHIFT FM MODE TUNING REAR LEVEL CENTER LEVEL POWER AMFM EE 2134 67890 5 SURROUND ON/OFF 41 E 16 23 22 1 2 (Page 16) (Page 11) STR-SE581 9 10 3-3.SCHEMATIC DIAGRAM DISPLAY SECTION See page 6 for Waveforms. See page 25 for IC Pin Func
33、tions. STR-SE581 H TO MAIN BOARD CNP503 TO MAIN BOARD CNP504 E TO MAIN BOARD CNS701 I TO MAIN BOARD CNS251 G 1-665-284- 11 (12) 1-665- 283- 1-665-261- 1-665- 255- 11 (12) 11 (12) 11 (12) M MASTER VOLUME SWITCH BOARD VIDEO BOARD VR-TONE BOARD VOLUME BOARD 110 E E E E E 10 1 E FRONTREARWOOFERCENTER J5
34、01 WOOFER J253 RLRLRL F TO DISPLAY BOARD CNS202 10 1 BASS BASS BOOST TREBLEBALANCE E E E E 58 41 16 15 30 1 1 5 4 8 1717 16 CN505CN501 (Page 15)(Page 15) (Page 15) (Page 7) (Page 15) JW261 E 11 12 3-4.PRINTED WIRING BOARD VOLUME/VIDEO SECTION 12 A B C D E F G H I 345678910111213 Ref. No.Location D23
35、8F-5 D310H-12 IC404C-9 IC500C-11 IC502C-12 Q361D-6 Q362C-6 Q363C-6 Q364C-6 Q365C-6 Q367H-11 Q401D-8 Q402D-9 Q451D-8 Q452D-9 Q501B-11 Semiconductor Location STR-SE581 13 14 3-5.SCHEMATIC DIAGRAM VOLUME/VIDEO SECTION See page 7 for KEY Board Printed Wiring Board. STR-SE581 1-665-279- 13 MAIN BOARD 1 5
36、 E E E E E E E E E E E E E E E E E E E E 1 9 E 1 1414 21 22 42 5588 1 7 1 7 1 1 3 13 15 E E 1 15 16 30 1 1 4 4 5 10 11 23 5 8 1 5 1 5 14 58 1 1 4 8 10 1 RY801 E G TO SWITCH BOARD CNS503 H TO SWITCH BOARD CNS504 I TO VIDEO BOARD CNS250 B TO SP-SW BOARD CNS705 C TO STANDBY BOARD CNP802 D TO SECONDARY
37、BOARD CNP801 TO SP-SW BOARD CNP703 CNP704 A 112 1324 E J TO DISPLAY BOARD CNS201 E TO VOLUME BOARD CNS402 AUDIO OUT AUDIO ININREC OUTCDPHONO FRONT SPEAKERS SURROUND SPEAKERS REAR ANTENNA CENTERRL RLRLRLRLRLRLRL VIDEOTAPE /MD A B TM701 TM601 TV/DBS TM1 E IC300 16 1 222 23 (Page 19) (Page 19) (Page 19
38、) (Page 19) (Page 7)(Page 11) (Page 12) (Page 12) (Page 12) 15 16 3-6.PRINTED WIRING BOARD MAIN SECTION 12 A B C D E F G H I J K 3456789101112131415 Ref. No.Location D311J-5 D312J-5 D560C-7 D610C-7 D710J-13 D721H-6 D722H-6 D723I-6 D724H-6 D725I-6 D726I-6 D727J-6 D728J-5 D801I-7 D802F-13 D803D-13 D80
39、4K-8 D810C-14 D811C-14 D812C-14 D813C-14 D814C-13 D815C-13 D817F-6 D818D-15 D901D-3 IC300H-5 IC301G-4 IC302H-3 IC401C-5 IC402C-3 IC501H-3 IC551H-8 IC601C-10 IC651D-10 IC701E-8 IC801E-6 IC802E-6 IC950B-11 Q551I-9 Q552I-10 Q553J-10 Q554I-10 Q560C-7 Q570I-9 Q610D-7 Q701H-8 Q702G-10 Q703H-10 Q704G-10 Q7
40、10K-12 Q720G-9 Q721H-6 Q722I-7 Q723I-6 Q751F-9 Q752E-10 Q753F-10 Q754E-10 Q770E-9 Q801I-8 Q802C-15 Q808F-6 Q809E-14 Q951B-12 Semiconductor Location STR-SE581 17 18 3-7.SCHEMATIC DIAGRAM MAIN SECTION (1/3) See page 6 for Waveforms. See page 27 for IC Block Diagrams. OSC STR-SE581 19 20 3-8.PRINTED WI
41、RING BOARD SP-SW, POWER SECTION 12 A B C D E F G H I 345678910111213 1 2 1 4 T902 CN902 CNP903 PRIMARY BOARD SECONDARY BOARD SP-SW BOARD STANDBY BOARD C TO MAIN BOARD CNS802 B A TO MAIN BOARD CNP702 TO MAIN BOARD CN706 D TO MAIN BOARD CN801 OFF ON TO MAIN BOARD CN706 A 1-665-289-11 (12) 1-665-285- 1
42、1 (12) 1-665- 286- 11 (12) 1-665-287- 11 (12) J741 PHONES S701 SPEAKERS T901 POWER TRANSFORMER 1 3 1 5 15 110 AC IN AC OUTLET 16 (Page 16) (Page 16) (Page 16) (Page 16) (Page 16) CNJ902 STR-SE581 21 22 3-9.SCHEMATIC DIAGRAM MAIN SECTION (2/3), SP-SW See page 15 for MAIN Board Printed Wiring Board. S
43、ee page 27 for IC Block Diagrams. STR-SE581 23 24 3-10. SCHEMATIC DIAGRAM MAIN SECTION (3/3), POWER See page 15 for MAIN Board Printed Wiring Board. See page 19 for SECONDARY/PRIMARY/STANDBY Board Printed Wiring Boards. See page 27 for IC Block Diagrams. CN902 CNP903 JW1 25 Pin No. 1 2 3 4 5 6 7 8 9
44、 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 I/O O O O O O O O I I I O O I O I I I I O O O I I I I O O Description Fluorescent indicator tube drive. Power supply (+5V). System clock. System data. PLL data input from TU001. Chip enable output. Chip ena
45、blr output. Input for model slect. Standby relay ON/OFF control. Protector detect input. System reset terminal. Auto stop detect input. Stereo detect input. Ground. Speaker relay drive. Surround Relay. Power relay drive. Not used. A/D signal input terminal. A/D3 key input terminal. A/D2 key input te
46、rminal. A/D1 key input terminal. Power supply (+5V). Reference voltage (+5V). Ground. Not used (Open). Ground. System clock (4.19MHz). System clock (4.19MHz). Mute drive output for PD2581V (IC701). Plologic LED drive. CINEMA STUDIO LED drive. Hall LED drive. Tuner mute drive output. Pin Name DIG7 DI
47、G6 DIG5 DIG4 DIG3 DIG2 DIG1 +5V S. CLK S. DATA PLL. DATA S. CE (LC7288) S. CE (LV100) REARRY BRIDGE CABLE PROTECT RESET AUTO-STOP STEREO-IN AVss SP-RY SURR-RY POWER-RY Not used SIGNAL A/D3 A/D2 A/D1 AVDD AV. REF GND NC Vss X1 X2 IC. MUTE PROLOGIC CSTUDIO HALL T. MUTE 3-11. IC PIN FUNCTION DISPLAY BO
48、ARD IC201 : PD78044FGF-064-3B9 (DISPLAY CONTROL) 26 Pin No. 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 I/O O O I I I I I I O O O I I I I I O O O O O O O O O O O O O O O O O O O Description Volume up. Volume down. Standby LE
49、D drive. System power ON/OFF. RDS data input terminal (EXCEPT Australian, E, Saudi Arabia, PX model). RDS clock input terminal (EXCEPT Australian, E, Saudi Arabia, PX model). Stop signal input from NJM2103D (IC950). Ground. Sircs signal input. Power switch input terminal. 5.1ch input LED. Power supply (+5V). Bass boost LED drive. Line mute drive. Surround Lch mute. Input for model select. Ke
免费区 
